summaryrefslogtreecommitdiffstats
path: root/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts
Commit message (Collapse)AuthorAgeFilesLines
* arm64: zynqmp: Add psgtr DT descriptionsMichal Simek2021-05-191-0/+31
| | | | | | | | | Mainline kernel has psgtr driver that's why it is good to add description to DT files. Some boards are just missing description for USB3 and sata. zc1751-dc1 and p-a2197 are also missing clock descriptions for input clocks. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* arm64: zynqmp: Add pinctrl descriptionMichal Simek2021-05-191-0/+229
| | | | | | | ZynqMP pinctrl Linux driver has been merged to 5.13-rc1 kernel. Based on it DT files can be extended by pinctrl configurations. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* xilinx: Sync DTs with Linux kernelMichal Simek2021-03-301-17/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are several changes which happen in mainline kernel which should get also to U-Boot. Here is the list of patches from the kernel: - ARM: zynq: Fix leds subnode name for zc702/zybo-z7 - arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1 - arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111 - arm64: dts: zynqmp: Wire up the DisplayPort subsystem - arm64: dts: zynqmp: Add DisplayPort subsystem - arm64: dts: zynqmp: Add DPDMA node - arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106 - arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111 - arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106 - arm64: dts: zynqmp-zcu100-revC: correct interrupt flags - arm64: dts: xilinx: align GPIO hog names with dtschema - arm64: zynqmp: Add Xilinx AES node - dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA but also some other changes have been done. - Using only one compatible string for adxl345 on zturn - Remove Xilinx internal DP bindings - Remove USB3.0 serdes configurations - Remove SATA serdes configuration for zc1232 - Resort nvmem_firmware - Update nand compatible string - Aling power-domains property for sd0/1 Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* xilinx: Fix xlnx,mio_bank propertyMichal Simek2020-08-201-2/+2
| | | | | | | | | | | s/xlnx,mio_bank/xlnx,mio-bank/g DT binding is describing mio-bank not mio_bank that's why fix all DTSes and also driver itself. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Peng Fan <peng.fan@nxp.com>
* arm64: zynqmp: Fix addresses in partition definitionsMichal Simek2020-04-061-4/+4
| | | | | | | | | | | | Node name should be <name>@<address> which is not how partitions are described. Issue was found by running dtbs_check as: flash@0: 'partition@qspi-device-tree', 'partition@qspi-fsbl-uboot', 'partition@qspi-linux', 'partition@qspi-rootfs' do not match any of the regexes: ... Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* arm64: zynqmp: Sync DP subsystemMichal Simek2020-04-061-14/+5
| | | | | | | | Sync DP subsystem with the latest state in Xilinx U-Boot repository. This binding hasn't been approved in mainline Linux but it is much better than ancient version which this patch removes. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* arm64: zynqmp: Add 'no-1-8-v' property for ZynqMP BoardsManish Narani2020-04-061-1/+4
| | | | | | | | | | Modify dts files to add 'no-1-8-v' property for all the ZynqMP boards. User can remove this property to enable the UHS mode. This is to keep the same speed (HS) modes across all the stages of the Linux Boot. Due to power cycling limitation of some of the ZynqMP boards, some SD cards don't get power cycled and are failing in Linux. Signed-off-by: Manish Narani <manish.narani@xilinx.com>
* arm64: zynqmp: Update Copyright years to 2020Michal Simek2020-04-061-1/+1
| | | | | | Trivial change. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* arm64: zynqmp: Use ethernet-phy as node name for ethernet physMichal Simek2019-10-241-1/+1
| | | | | | | Ethernet phys based on devicetree specification should be using ethernet-phy@ node name instead of pure phy@. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* dts: switch spi-flash to jedec, spi-nor compatibleNeil Armstrong2019-04-121-1/+1
| | | | | | | | | | | | | | | | | | | | There is no reason not to use the Linux "jedec,spi-nor" binding in U-Boot dts files. This compatible has been added in sf_probe, let use it. This patch switches to jedec,spi-nor when spi-flash is used in the DTS and DTSI files, and removed spi-flash when jedec,spi-nor is already present. The x86 dts are switched in a separate commit since it depends on a change in fdtdec. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Evgeniy Paltsev <paltsev@synopsys.com> Reviewed-by: Rick Chen <rick@andestech.com> Reviewed-by: Patrick Delaunay <Patrick.delaunay@st.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
* arm64: zynqmp: Wire spi-flash compatible string with flashesMichal Simek2018-11-291-1/+1
| | | | | | | | Enable reading tx and rx buswidth from DT via spi-uclass. To get these from uclass spi-flash compatible string has to be added to flash node. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* arm64: zynqmp: Add eeprom reference to eeprom nodesMichal Simek2018-04-091-1/+2
| | | | | | eeprom can contain information which can be used by nvmem drivers. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* arm64: zynqmp: Use atmel prefix instead of atMichal Simek2018-04-091-1/+1
| | | | | | This changes was done in mainline and this patch is just following it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* arm64: zynqmp: Remove additional comments from dts filesMichal Simek2018-04-091-1/+0
| | | | | | Remove additional comments which were removed as the part of upstreaming. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* arm64: zynqmp: Sync up license with mainline kernelMichal Simek2018-04-091-3/+2
| | | | | | | | | | Mainline Linux kernel has adopted SPDX header license in a different format then was used before. This patch is syncing it up. Also update years in License text and remove Nathalie's email because it is no longer valid. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* arm64: zynqmp: Convert board to use zynqmp-clk driverMichal Simek2018-03-231-1/+1
| | | | | | Use zynqmp clock driver instead of fixed clocks. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* arm64: zynqmp: Remove undocumented dma propertiesMichal Simek2017-12-141-9/+0
| | | | | | | | | Remove overfetch, ratectrl, include-sg and src-issue dma properties. Driver is not using them and they are also not documented in the binding doc. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
* arm64: zynqmp: Remove local-mac-address from dtsi fileMichal Simek2017-11-281-1/+0
| | | | | | | | Generic dtsi file can't use the same mac address for all. U-Boot read mac from eeprom in zcu102 case and for others random mac address is generated. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Fix usb nodes for dc1 and dc2Michal Simek2017-01-101-0/+4
| | | | | | | Fix DT binding for usb nodes. Setup correct aliases and enable dwc3 nodes. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: change sdhci compatible string.Sai Krishna Potthuri2016-11-151-0/+2
| | | | | | | | This patch changes the compatible string for sdhci node, adds "xlnx,device_id" and "xlnx,mio_bank" property to sdhci node. Signed-off-by: Sai Krishna Potthuri <lakshmis@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Remove DTC 1.4.2 warningsMichal Simek2016-11-151-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DTC 1.4.2 reports these warnings: Warning (unit_address_vs_reg): Node /amba_apu has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /amba has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /amba/usb@fe200000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /amba/usb@fe300000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /amba/dma@fd4c0000/dma-video0channel@fd4c0000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /amba/dma@fd4c0000/dma-video1channel@fd4c0000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /amba/dma@fd4c0000/dma-video2channel@fd4c0000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /amba/dma@fd4c0000/dma-graphicschannel@fd4c0000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /amba/dma@fd4c0000/dma-audio0channel@fd4c0000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /amba/dma@fd4c0000/dma-audio1channel@fd4c0000 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name This patch is fixing them. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Add support for zc1751 with DC cardsMichal Simek2016-04-131-0/+211
Support ZynqMP zc1751 with DC cards. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit (git 2.34.1) at 2025-02-01 12:51:00 +0000