summaryrefslogtreecommitdiffstats
path: root/drivers/usb/gadget/omap_udc.h
blob: 652ee462734470345eed415a474c096fbe4a7909 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
/*
 * omap_udc.h -- for omap 3.2 udc, with OTG support
 *
 * 2004 (C) Texas Instruments, Inc.
 * 2004 (C) David Brownell
 */

/*
 * USB device/endpoint management registers
 */
#define UDC_REG(offset)              __REG16(UDC_BASE + (offset))

#define	UDC_REV_REG			UDC_REG(0x0)	/* Revision */
#define	UDC_EP_NUM_REG			UDC_REG(0x4)	/* Which endpoint */
#	define	UDC_SETUP_SEL		(1 << 6)
#	define	UDC_EP_SEL		(1 << 5)
#	define	UDC_EP_DIR		(1 << 4)
	/* low 4 bits for endpoint number */
#define	UDC_DATA_REG			UDC_REG(0x08)	/* Endpoint FIFO */
#define	UDC_CTRL_REG			UDC_REG(0x0C)	/* Endpoint control */
#	define	UDC_CLR_HALT		(1 << 7)
#	define	UDC_SET_HALT		(1 << 6)
#	define	UDC_CLRDATA_TOGGLE	(1 << 3)
#	define	UDC_SET_FIFO_EN		(1 << 2)
#	define	UDC_CLR_EP		(1 << 1)
#	define	UDC_RESET_EP		(1 << 0)
#define	UDC_STAT_FLG_REG		UDC_REG(0x10)	/* Endpoint status */
#	define	UDC_NO_RXPACKET		(1 << 15)
#	define	UDC_MISS_IN		(1 << 14)
#	define	UDC_DATA_FLUSH		(1 << 13)
#	define	UDC_ISO_ERR		(1 << 12)
#	define	UDC_ISO_FIFO_EMPTY	(1 << 9)
#	define	UDC_ISO_FIFO_FULL	(1 << 8)
#	define	UDC_EP_HALTED		(1 << 6)
#	define	UDC_STALL		(1 << 5)
#	define	UDC_NAK			(1 << 4)
#	define	UDC_ACK			(1 << 3)
#	define	UDC_FIFO_EN		(1 << 2)
#	define	UDC_NON_ISO_FIFO_EMPTY	(1 << 1)
#	define	UDC_NON_ISO_FIFO_FULL	(1 << 0)
#define	UDC_RXFSTAT_REG			UDC_REG(0x14)	/* OUT bytecount */
#define	UDC_SYSCON1_REG			UDC_REG(0x18)	/* System config 1 */
#	define	UDC_CFG_LOCK		(1 << 8)
#	define	UDC_DATA_ENDIAN		(1 << 7)
#	define	UDC_DMA_ENDIAN		(1 << 6)
#	define	UDC_NAK_EN		(1 << 4)
#	define	UDC_AUTODECODE_DIS	(1 << 3)
#	define	UDC_SELF_PWR		(1 << 2)
#	define	UDC_SOFF_DIS		(1 << 1)
#	define	UDC_PULLUP_EN		(1 << 0)
#define	UDC_SYSCON2_REG			UDC_REG(0x1C)	/* System config 2 */
#	define	UDC_RMT_WKP		(1 << 6)
#	define	UDC_STALL_CMD		(1 << 5)
#	define	UDC_DEV_CFG		(1 << 3)
#	define	UDC_CLR_CFG		(1 << 2)
#define	UDC_DEVSTAT_REG			UDC_REG(0x20)	/* Device status */
#	define	UDC_B_HNP_ENABLE	(1 << 9)
#	define	UDC_A_HNP_SUPPORT	(1 << 8)
#	define	UDC_A_ALT_HNP_SUPPORT	(1 << 7)
#	define	UDC_R_WK_OK		(1 << 6)
#	define	UDC_USB_RESET		(1 << 5)
#	define	UDC_SUS			(1 << 4)
#	define	UDC_CFG			(1 << 3)
#	define	UDC_ADD			(1 << 2)
#	define	UDC_DEF			(1 << 1)
#	define	UDC_ATT			(1 << 0)
#define	UDC_SOF_REG			UDC_REG(0x24)	/* Start of frame */
#	define	UDC_FT_LOCK		(1 << 12)
#	define	UDC_TS_OK		(1 << 11)
#	define	UDC_TS			0x03ff
#define	UDC_IRQ_EN_REG			UDC_REG(0x28)	/* Interrupt enable */
#	define	UDC_SOF_IE		(1 << 7)
#	define	UDC_EPN_RX_IE		(1 << 5)
#	define	UDC_EPN_TX_IE		(1 << 4)
#	define	UDC_DS_CHG_IE		(1 << 3)
#	define	UDC_EP0_IE		(1 << 0)
#define	UDC_DMA_IRQ_EN_REG		UDC_REG(0x2C)	/* DMA irq enable */
	/* rx/tx dma channels numbered 1-3 not 0-2 */
#	define	UDC_TX_DONE_IE(n)	(1 << (4 * (n) - 2))
#	define	UDC_RX_CNT_IE(n)	(1 << (4 * (n) - 3))
#	define	UDC_RX_EOT_IE(n)	(1 << (4 * (n) - 4))
#define	UDC_IRQ_SRC_REG			UDC_REG(0x30)	/* Interrupt source */
#	define	UDC_TXN_DONE		(1 << 10)
#	define	UDC_RXN_CNT		(1 << 9)
#	define	UDC_RXN_EOT		(1 << 8)
#	define	UDC_SOF			(1 << 7)
#	define	UDC_EPN_RX		(1 << 5)
#	define	UDC_EPN_TX		(1 << 4)
#	define	UDC_DS_CHG		(1 << 3)
#	define	UDC_SETUP		(1 << 2)
#	define	UDC_EP0_RX		(1 << 1)
#	define	UDC_EP0_TX		(1 << 0)
#	define	UDC_IRQ_SRC_MASK	0x7bf
#define	UDC_EPN_STAT_REG		UDC_REG(0x34)	/* EP irq status */
#define	UDC_DMAN_STAT_REG		UDC_REG(0x38)	/* DMA irq status */
#	define	UDC_DMA_RX_SB		(1 << 12)
#	define	UDC_DMA_RX_SRC(x)	(((x)>>8) & 0xf)
#	define	UDC_DMA_TX_SRC(x)	(((x)>>0) & 0xf)


/* DMA configuration registers:  up to three channels in each direction.  */
#define	UDC_RXDMA_CFG_REG		UDC_REG(0x40)	/* 3 eps for RX DMA */
#	define	UDC_DMA_REQ		(1 << 12)
#define	UDC_TXDMA_CFG_REG		UDC_REG(0x44)	/* 3 eps for TX DMA */
#define	UDC_DATA_DMA_REG		UDC_REG(0x48)	/* rx/tx fifo addr */

/* rx/tx dma control, numbering channels 1-3 not 0-2 */
#define	UDC_TXDMA_REG(chan)		UDC_REG(0x50 - 4 + 4 * (chan))
#	define UDC_TXN_EOT		(1 << 15)	/* bytes vs packets */
#	define UDC_TXN_START		(1 << 14)	/* start transfer */
#	define UDC_TXN_TSC		0x03ff		/* units in xfer */
#define	UDC_RXDMA_REG(chan)		UDC_REG(0x60 - 4 + 4 * (chan))
#	define UDC_RXN_STOP		(1 << 15)	/* enable EOT irq */
#	define UDC_RXN_TC		0x00ff		/* packets in xfer */


/*
 * Endpoint configuration registers (used before CFG_LOCK is set)
 * UDC_EP_TX_REG(0) is unused
 */
#define	UDC_EP_RX_REG(endpoint)		UDC_REG(0x80 + (endpoint)*4)
#	define	UDC_EPN_RX_VALID	(1 << 15)
#	define	UDC_EPN_RX_DB		(1 << 14)
	/* buffer size in bits 13, 12 */
#	define	UDC_EPN_RX_ISO		(1 << 11)
	/* buffer pointer in low 11 bits */
#define	UDC_EP_TX_REG(endpoint)		UDC_REG(0xc0 + (endpoint)*4)
	/* same bitfields as in RX_REG */

/*-------------------------------------------------------------------------*/

struct omap_req {
	struct usb_request		req;
	struct list_head		queue;
	unsigned			dma_bytes;
	unsigned			mapped:1;
};

struct omap_ep {
	struct usb_ep			ep;
	struct list_head		queue;
	unsigned long			irqs;
	struct list_head		iso;
	const struct usb_endpoint_descriptor	*desc;
	char				name[14];
	u16				maxpacket;
	u8				bEndpointAddress;
	u8				bmAttributes;
	unsigned			double_buf:1;
	unsigned			stopped:1;
	unsigned			fnf:1;
	unsigned			has_dma:1;
	u8				ackwait;
	u8				dma_channel;
	u16				dma_counter;
	int				lch;
	struct omap_udc			*udc;
	struct timer_list		timer;
};

struct omap_udc {
	struct usb_gadget		gadget;
	struct usb_gadget_driver	*driver;
	spinlock_t			lock;
	struct omap_ep			ep[32];
	u16				devstat;
	u16				clr_halt;
	struct otg_transceiver		*transceiver;
	struct list_head		iso;
	unsigned			softconnect:1;
	unsigned			vbus_active:1;
	unsigned			ep0_pending:1;
	unsigned			ep0_in:1;
	unsigned			ep0_set_config:1;
	unsigned			ep0_reset_config:1;
	unsigned			ep0_setup:1;
	struct completion		*done;
};

/*-------------------------------------------------------------------------*/

#ifdef DEBUG
#define DBG(stuff...)		printk(KERN_DEBUG "udc: " stuff)
#else
#define DBG(stuff...)		do{}while(0)
#endif

#ifdef VERBOSE
#    define VDBG		DBG
#else
#    define VDBG(stuff...)	do{}while(0)
#endif

#define ERR(stuff...)		printk(KERN_ERR "udc: " stuff)
#define WARN(stuff...)		printk(KERN_WARNING "udc: " stuff)
#define INFO(stuff...)		printk(KERN_INFO "udc: " stuff)

/*-------------------------------------------------------------------------*/

#define	MOD_CONF_CTRL_0_REG	__REG32(MOD_CONF_CTRL_0)
#define	VBUS_W2FC_1510		(1 << 17)	/* 0 gpio0, 1 dvdd2 pin */

#define	FUNC_MUX_CTRL_0_REG	__REG32(FUNC_MUX_CTRL_0)
#define	VBUS_CTRL_1510		(1 << 19)	/* 1 connected (software) */
#define	VBUS_MODE_1510		(1 << 18)	/* 0 hardware, 1 software */

#define	HMC_1510	((MOD_CONF_CTRL_0_REG >> 1) & 0x3f)
#define	HMC_1610	(OTG_SYSCON_2_REG & 0x3f)
#define	HMC		(cpu_is_omap15xx() ? HMC_1510 : HMC_1610)