summaryrefslogtreecommitdiffstats
path: root/drivers/usb/host/ehci-pci.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/usb/host/ehci-pci.c')
-rw-r--r--drivers/usb/host/ehci-pci.c46
1 files changed, 38 insertions, 8 deletions
diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c
index 441c26064b4..13f73a836e4 100644
--- a/drivers/usb/host/ehci-pci.c
+++ b/drivers/usb/host/ehci-pci.c
@@ -121,8 +121,8 @@ static int ehci_pci_reinit(struct ehci_hcd *ehci, struct pci_dev *pdev)
return 0;
}
-/* called by khubd or root hub (re)init threads; leaves HC in halt state */
-static int ehci_pci_reset(struct usb_hcd *hcd)
+/* called during probe() after chip reset completes */
+static int ehci_pci_setup(struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
struct pci_dev *pdev = to_pci_dev(hcd->self.controller);
@@ -141,6 +141,11 @@ static int ehci_pci_reset(struct usb_hcd *hcd)
if (retval)
return retval;
+ /* data structure init */
+ retval = ehci_init(hcd);
+ if (retval)
+ return retval;
+
/* NOTE: only the parts below this line are PCI-specific */
switch (pdev->vendor) {
@@ -154,7 +159,8 @@ static int ehci_pci_reset(struct usb_hcd *hcd)
/* AMD8111 EHCI doesn't work, according to AMD errata */
if (pdev->device == 0x7463) {
ehci_info(ehci, "ignoring AMD8111 (errata)\n");
- return -EIO;
+ retval = -EIO;
+ goto done;
}
break;
case PCI_VENDOR_ID_NVIDIA:
@@ -207,9 +213,8 @@ static int ehci_pci_reset(struct usb_hcd *hcd)
/* REVISIT: per-port wake capability (PCI 0x62) currently unused */
retval = ehci_pci_reinit(ehci, pdev);
-
- /* finish init */
- return ehci_init(hcd);
+done:
+ return retval;
}
/*-------------------------------------------------------------------------*/
@@ -228,14 +233,36 @@ static int ehci_pci_reset(struct usb_hcd *hcd)
static int ehci_pci_suspend(struct usb_hcd *hcd, pm_message_t message)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+ unsigned long flags;
+ int rc = 0;
if (time_before(jiffies, ehci->next_statechange))
msleep(10);
+ /* Root hub was already suspended. Disable irq emission and
+ * mark HW unaccessible, bail out if RH has been resumed. Use
+ * the spinlock to properly synchronize with possible pending
+ * RH suspend or resume activity.
+ *
+ * This is still racy as hcd->state is manipulated outside of
+ * any locks =P But that will be a different fix.
+ */
+ spin_lock_irqsave (&ehci->lock, flags);
+ if (hcd->state != HC_STATE_SUSPENDED) {
+ rc = -EINVAL;
+ goto bail;
+ }
+ writel (0, &ehci->regs->intr_enable);
+ (void)readl(&ehci->regs->intr_enable);
+
+ clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
+ bail:
+ spin_unlock_irqrestore (&ehci->lock, flags);
+
// could save FLADJ in case of Vaux power loss
// ... we'd only use it to handle clock skew
- return 0;
+ return rc;
}
static int ehci_pci_resume(struct usb_hcd *hcd)
@@ -251,6 +278,9 @@ static int ehci_pci_resume(struct usb_hcd *hcd)
if (time_before(jiffies, ehci->next_statechange))
msleep(100);
+ /* Mark hardware accessible again as we are out of D3 state by now */
+ set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
+
/* If CF is clear, we lost PCI Vaux power and need to restart. */
if (readl(&ehci->regs->configured_flag) != FLAG_CF)
goto restart;
@@ -319,7 +349,7 @@ static const struct hc_driver ehci_pci_hc_driver = {
/*
* basic lifecycle operations
*/
- .reset = ehci_pci_reset,
+ .reset = ehci_pci_setup,
.start = ehci_run,
#ifdef CONFIG_PM
.suspend = ehci_pci_suspend,