diff options
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_82598.c | 115 | ||||
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_82599.c | 13 | ||||
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_common.c | 245 | ||||
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_common.h | 4 | ||||
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_dcb_82599.c | 2 | ||||
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_ethtool.c | 28 | ||||
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_main.c | 6 | ||||
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_type.h | 7 |
8 files changed, 193 insertions, 227 deletions
diff --git a/drivers/net/ixgbe/ixgbe_82598.c b/drivers/net/ixgbe/ixgbe_82598.c index 88e8350aa78..b9923047ce1 100644 --- a/drivers/net/ixgbe/ixgbe_82598.c +++ b/drivers/net/ixgbe/ixgbe_82598.c @@ -293,6 +293,17 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num) u32 rmcs_reg; u32 reg; +#ifdef CONFIG_DCB + if (hw->fc.requested_mode == ixgbe_fc_pfc) + goto out; + +#endif /* CONFIG_DCB */ + /* Negotiate the fc mode to use */ + ret_val = ixgbe_fc_autoneg(hw); + if (ret_val) + goto out; + + /* Disable any previous flow control settings */ fctrl_reg = IXGBE_READ_REG(hw, IXGBE_FCTRL); fctrl_reg &= ~(IXGBE_FCTRL_RFCE | IXGBE_FCTRL_RPFCE); @@ -304,14 +315,20 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num) * 0: Flow control is completely disabled * 1: Rx flow control is enabled (we can receive pause frames, * but not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames but + * 2: Tx flow control is enabled (we can send pause frames but * we do not support receiving pause frames). * 3: Both Rx and Tx flow control (symmetric) are enabled. * other: Invalid. +#ifdef CONFIG_DCB + * 4: Priority Flow Control is enabled. +#endif */ switch (hw->fc.current_mode) { case ixgbe_fc_none: - /* Flow control completely disabled by software override. */ + /* + * Flow control is disabled by software override or autoneg. + * The code below will actually disable it in the HW. + */ break; case ixgbe_fc_rx_pause: /* @@ -336,6 +353,11 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num) fctrl_reg |= IXGBE_FCTRL_RFCE; rmcs_reg |= IXGBE_RMCS_TFCE_802_3X; break; +#ifdef CONFIG_DCB + case ixgbe_fc_pfc: + goto out; + break; +#endif /* CONFIG_DCB */ default: hw_dbg(hw, "Flow control param set incorrectly\n"); ret_val = -IXGBE_ERR_CONFIG; @@ -343,7 +365,7 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num) break; } - /* Enable 802.3x based flow control settings. */ + /* Set 802.3x based flow control settings. */ fctrl_reg |= IXGBE_FCTRL_DPF; IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl_reg); IXGBE_WRITE_REG(hw, IXGBE_RMCS, rmcs_reg); @@ -377,79 +399,6 @@ out: } /** - * ixgbe_setup_fc_82598 - Configure flow control settings - * @hw: pointer to hardware structure - * @packetbuf_num: packet buffer number (0-7) - * - * Configures the flow control settings based on SW configuration. This - * function is used for 802.3x flow control configuration only. - **/ -static s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num) -{ - s32 ret_val = 0; - ixgbe_link_speed speed; - bool link_up; - - /* Validate the packetbuf configuration */ - if (packetbuf_num < 0 || packetbuf_num > 7) { - hw_dbg(hw, "Invalid packet buffer number [%d], expected range is" - " 0-7\n", packetbuf_num); - ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; - goto out; - } - - /* - * Validate the water mark configuration. Zero water marks are invalid - * because it causes the controller to just blast out fc packets. - */ - if (!hw->fc.low_water || !hw->fc.high_water || !hw->fc.pause_time) { - if (hw->fc.requested_mode != ixgbe_fc_none) { - hw_dbg(hw, "Invalid water mark configuration\n"); - ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; - goto out; - } - } - - /* - * Validate the requested mode. Strict IEEE mode does not allow - * ixgbe_fc_rx_pause because it will cause testing anomalies. - */ - if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { - hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n"); - ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; - goto out; - } - - /* - * 10gig parts do not have a word in the EEPROM to determine the - * default flow control setting, so we explicitly set it to full. - */ - if (hw->fc.requested_mode == ixgbe_fc_default) - hw->fc.requested_mode = ixgbe_fc_full; - - /* - * Save off the requested flow control mode for use later. Depending - * on the link partner's capabilities, we may or may not use this mode. - */ - - hw->fc.current_mode = hw->fc.requested_mode; - - /* Decide whether to use autoneg or not. */ - hw->mac.ops.check_link(hw, &speed, &link_up, false); - if (!hw->fc.disable_fc_autoneg && hw->phy.multispeed_fiber && - (speed == IXGBE_LINK_SPEED_1GB_FULL)) - ret_val = ixgbe_fc_autoneg(hw); - - if (ret_val) - goto out; - - ret_val = ixgbe_fc_enable_82598(hw, packetbuf_num); - -out: - return ret_val; -} - -/** * ixgbe_setup_mac_link_82598 - Configures MAC link settings * @hw: pointer to hardware structure * @@ -488,13 +437,6 @@ static s32 ixgbe_setup_mac_link_82598(struct ixgbe_hw *hw) } } - /* - * We want to save off the original Flow Control configuration just in - * case we get disconnected and then reconnected into a different hub - * or switch with different Flow Control capabilities. - */ - ixgbe_setup_fc_82598(hw, 0); - /* Add delay to filter out noises during initial link setup */ msleep(50); @@ -581,6 +523,11 @@ static s32 ixgbe_check_mac_link_82598(struct ixgbe_hw *hw, else *speed = IXGBE_LINK_SPEED_1GB_FULL; + /* if link is down, zero out the current_mode */ + if (*link_up == false) { + hw->fc.current_mode = ixgbe_fc_none; + hw->fc.fc_was_autonegged = false; + } out: return 0; } @@ -1168,7 +1115,7 @@ static struct ixgbe_mac_operations mac_ops_82598 = { .disable_mc = &ixgbe_disable_mc_generic, .clear_vfta = &ixgbe_clear_vfta_82598, .set_vfta = &ixgbe_set_vfta_82598, - .setup_fc = &ixgbe_setup_fc_82598, + .fc_enable = &ixgbe_fc_enable_82598, }; static struct ixgbe_eeprom_operations eeprom_ops_82598 = { diff --git a/drivers/net/ixgbe/ixgbe_82599.c b/drivers/net/ixgbe/ixgbe_82599.c index 84b83f7b473..4d83e591659 100644 --- a/drivers/net/ixgbe/ixgbe_82599.c +++ b/drivers/net/ixgbe/ixgbe_82599.c @@ -413,9 +413,6 @@ s32 ixgbe_setup_mac_link_82599(struct ixgbe_hw *hw) } } - /* Set up flow control */ - status = ixgbe_setup_fc_generic(hw, 0); - /* Add delay to filter out noises during initial link setup */ msleep(50); @@ -641,6 +638,11 @@ s32 ixgbe_check_mac_link_82599(struct ixgbe_hw *hw, ixgbe_link_speed *speed, else *speed = IXGBE_LINK_SPEED_100_FULL; + /* if link is down, zero out the current_mode */ + if (*link_up == false) { + hw->fc.current_mode = ixgbe_fc_none; + hw->fc.fc_was_autonegged = false; + } return 0; } @@ -747,9 +749,6 @@ s32 ixgbe_setup_mac_link_speed_82599(struct ixgbe_hw *hw, } } - /* Set up flow control */ - status = ixgbe_setup_fc_generic(hw, 0); - /* Add delay to filter out noises during initial link setup */ msleep(50); } @@ -1509,7 +1508,7 @@ static struct ixgbe_mac_operations mac_ops_82599 = { .disable_mc = &ixgbe_disable_mc_generic, .clear_vfta = &ixgbe_clear_vfta_82599, .set_vfta = &ixgbe_set_vfta_82599, - .setup_fc = &ixgbe_setup_fc_generic, + .fc_enable = &ixgbe_fc_enable_generic, .init_uta_tables = &ixgbe_init_uta_tables_82599, .setup_sfp = &ixgbe_setup_sfp_modules_82599, }; diff --git a/drivers/net/ixgbe/ixgbe_common.c b/drivers/net/ixgbe/ixgbe_common.c index 4d36cd32cd3..db339d6fe63 100644 --- a/drivers/net/ixgbe/ixgbe_common.c +++ b/drivers/net/ixgbe/ixgbe_common.c @@ -85,6 +85,9 @@ s32 ixgbe_start_hw_generic(struct ixgbe_hw *hw) IXGBE_WRITE_REG(hw, IXGBE_CTRL_EXT, ctrl_ext); IXGBE_WRITE_FLUSH(hw); + /* Setup flow control */ + ixgbe_setup_fc(hw, 0); + /* Clear adapter stopped flag */ hw->adapter_stopped = false; @@ -1577,17 +1580,16 @@ s32 ixgbe_disable_mc_generic(struct ixgbe_hw *hw) } /** - * ixgbe_fc_enable - Enable flow control + * ixgbe_fc_enable_generic - Enable flow control * @hw: pointer to hardware structure * @packetbuf_num: packet buffer number (0-7) * * Enable flow control according to the current settings. **/ -s32 ixgbe_fc_enable(struct ixgbe_hw *hw, s32 packetbuf_num) +s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw, s32 packetbuf_num) { s32 ret_val = 0; - u32 mflcn_reg; - u32 fccfg_reg; + u32 mflcn_reg, fccfg_reg; u32 reg; u32 rx_pba_size; @@ -1596,7 +1598,12 @@ s32 ixgbe_fc_enable(struct ixgbe_hw *hw, s32 packetbuf_num) goto out; #endif /* CONFIG_DCB */ + /* Negotiate the fc mode to use */ + ret_val = ixgbe_fc_autoneg(hw); + if (ret_val) + goto out; + /* Disable any previous flow control settings */ mflcn_reg = IXGBE_READ_REG(hw, IXGBE_MFLCN); mflcn_reg &= ~(IXGBE_MFLCN_RFCE | IXGBE_MFLCN_RPFCE); @@ -1616,7 +1623,10 @@ s32 ixgbe_fc_enable(struct ixgbe_hw *hw, s32 packetbuf_num) */ switch (hw->fc.current_mode) { case ixgbe_fc_none: - /* Flow control completely disabled by software override. */ + /* + * Flow control is disabled by software override or autoneg. + * The code below will actually disable it in the HW. + */ break; case ixgbe_fc_rx_pause: /* @@ -1645,7 +1655,7 @@ s32 ixgbe_fc_enable(struct ixgbe_hw *hw, s32 packetbuf_num) case ixgbe_fc_pfc: goto out; break; -#endif +#endif /* CONFIG_DCB */ default: hw_dbg(hw, "Flow control param set incorrectly\n"); ret_val = -IXGBE_ERR_CONFIG; @@ -1653,7 +1663,7 @@ s32 ixgbe_fc_enable(struct ixgbe_hw *hw, s32 packetbuf_num) break; } - /* Enable 802.3x based flow control settings. */ + /* Set 802.3x based flow control settings. */ mflcn_reg |= IXGBE_MFLCN_DPF; IXGBE_WRITE_REG(hw, IXGBE_MFLCN, mflcn_reg); IXGBE_WRITE_REG(hw, IXGBE_FCCFG, fccfg_reg); @@ -1661,10 +1671,12 @@ s32 ixgbe_fc_enable(struct ixgbe_hw *hw, s32 packetbuf_num) reg = IXGBE_READ_REG(hw, IXGBE_MTQC); /* Thresholds are different for link flow control when in DCB mode */ if (reg & IXGBE_MTQC_RT_ENA) { + rx_pba_size = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(packetbuf_num)); + /* Always disable XON for LFC when in DCB mode */ - IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(packetbuf_num), 0); + reg = (rx_pba_size >> 5) & 0xFFE0; + IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(packetbuf_num), reg); - rx_pba_size = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(packetbuf_num)); reg = (rx_pba_size >> 2) & 0xFFE0; if (hw->fc.current_mode & ixgbe_fc_tx_pause) reg |= IXGBE_FCRTH_FCEN; @@ -1709,100 +1721,41 @@ out: * ixgbe_fc_autoneg - Configure flow control * @hw: pointer to hardware structure * - * Negotiates flow control capabilities with link partner using autoneg and - * applies the results. + * Compares our advertised flow control capabilities to those advertised by + * our link partner, and determines the proper flow control mode to use. **/ s32 ixgbe_fc_autoneg(struct ixgbe_hw *hw) { s32 ret_val = 0; - u32 i, reg, pcs_anadv_reg, pcs_lpab_reg; - - reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); + ixgbe_link_speed speed; + u32 pcs_anadv_reg, pcs_lpab_reg, linkstat; + bool link_up; /* - * The possible values of fc.current_mode are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause frames, - * but not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames but - * we do not support receiving pause frames). - * 3: Both Rx and Tx flow control (symmetric) are enabled. - * 4: Priority Flow Control is enabled. - * other: Invalid. + * AN should have completed when the cable was plugged in. + * Look for reasons to bail out. Bail out if: + * - FC autoneg is disabled, or if + * - we don't have multispeed fiber, or if + * - we're not running at 1G, or if + * - link is not up, or if + * - link is up but AN did not complete, or if + * - link is up and AN completed but timed out + * + * Since we're being called from an LSC, link is already know to be up. + * So use link_up_wait_to_complete=false. */ - switch (hw->fc.current_mode) { - case ixgbe_fc_none: - /* Flow control completely disabled by software override. */ - reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); - break; - case ixgbe_fc_rx_pause: - /* - * Rx Flow control is enabled and Tx Flow control is - * disabled by software override. Since there really - * isn't a way to advertise that we are capable of RX - * Pause ONLY, we will advertise that we support both - * symmetric and asymmetric Rx PAUSE. Later, we will - * disable the adapter's ability to send PAUSE frames. - */ - reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); - break; - case ixgbe_fc_tx_pause: - /* - * Tx Flow control is enabled, and Rx Flow control is - * disabled by software override. - */ - reg |= (IXGBE_PCS1GANA_ASM_PAUSE); - reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE); - break; - case ixgbe_fc_full: - /* Flow control (both Rx and Tx) is enabled by SW override. */ - reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); - break; -#ifdef CONFIG_DCB - case ixgbe_fc_pfc: - goto out; - break; -#endif - default: - hw_dbg(hw, "Flow control param set incorrectly\n"); - ret_val = -IXGBE_ERR_CONFIG; - goto out; - break; - } - - IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg); - reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL); - - /* Set PCS register for autoneg */ - /* Enable and restart autoneg */ - reg |= IXGBE_PCS1GLCTL_AN_ENABLE | IXGBE_PCS1GLCTL_AN_RESTART; - - /* Disable AN timeout */ - if (hw->fc.strict_ieee) - reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN; - - hw_dbg(hw, "Configuring Autoneg; PCS_LCTL = 0x%08X\n", reg); - IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg); - - /* See if autonegotiation has succeeded */ - hw->mac.autoneg_succeeded = 0; - for (i = 0; i < FIBER_LINK_UP_LIMIT; i++) { - msleep(10); - reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA); - if ((reg & (IXGBE_PCS1GLSTA_LINK_OK | - IXGBE_PCS1GLSTA_AN_COMPLETE)) == - (IXGBE_PCS1GLSTA_LINK_OK | - IXGBE_PCS1GLSTA_AN_COMPLETE)) { - if (!(reg & IXGBE_PCS1GLSTA_AN_TIMED_OUT)) - hw->mac.autoneg_succeeded = 1; - break; - } - } - - if (!hw->mac.autoneg_succeeded) { - /* Autoneg failed to achieve a link, so we turn fc off */ - hw->fc.current_mode = ixgbe_fc_none; - hw_dbg(hw, "Flow Control = NONE.\n"); + hw->mac.ops.check_link(hw, &speed, &link_up, false); + linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA); + + if (hw->fc.disable_fc_autoneg || + !hw->phy.multispeed_fiber || + (speed != IXGBE_LINK_SPEED_1GB_FULL) || + !link_up || + ((linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) || + ((linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1)) { + hw->fc.fc_was_autonegged = false; + hw->fc.current_mode = hw->fc.requested_mode; + hw_dbg(hw, "Autoneg FC was skipped.\n"); goto out; } @@ -1845,21 +1798,23 @@ s32 ixgbe_fc_autoneg(struct ixgbe_hw *hw) hw_dbg(hw, "Flow Control = NONE.\n"); } + /* Record that current_mode is the result of a successful autoneg */ + hw->fc.fc_was_autonegged = true; + out: return ret_val; } /** - * ixgbe_setup_fc_generic - Set up flow control + * ixgbe_setup_fc - Set up flow control * @hw: pointer to hardware structure * - * Sets up flow control. + * Called at init time to set up flow control. **/ -s32 ixgbe_setup_fc_generic(struct ixgbe_hw *hw, s32 packetbuf_num) +s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) { s32 ret_val = 0; - ixgbe_link_speed speed; - bool link_up; + u32 reg; #ifdef CONFIG_DCB if (hw->fc.requested_mode == ixgbe_fc_pfc) { @@ -1881,16 +1836,14 @@ s32 ixgbe_setup_fc_generic(struct ixgbe_hw *hw, s32 packetbuf_num) * because it causes the controller to just blast out fc packets. */ if (!hw->fc.low_water || !hw->fc.high_water || !hw->fc.pause_time) { - if (hw->fc.requested_mode != ixgbe_fc_none) { - hw_dbg(hw, "Invalid water mark configuration\n"); - ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; - goto out; - } + hw_dbg(hw, "Invalid water mark configuration\n"); + ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; + goto out; } /* * Validate the requested mode. Strict IEEE mode does not allow - * ixgbe_fc_rx_pause because it will cause testing anomalies. + * ixgbe_fc_rx_pause because it will cause us to fail at UNH. */ if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict " @@ -1907,21 +1860,77 @@ s32 ixgbe_setup_fc_generic(struct ixgbe_hw *hw, s32 packetbuf_num) hw->fc.requested_mode = ixgbe_fc_full; /* - * Save off the requested flow control mode for use later. Depending - * on the link partner's capabilities, we may or may not use this mode. + * Set up the 1G flow control advertisement registers so the HW will be + * able to do fc autoneg once the cable is plugged in. If we end up + * using 10g instead, this is harmless. */ - hw->fc.current_mode = hw->fc.requested_mode; - - /* Decide whether to use autoneg or not. */ - hw->mac.ops.check_link(hw, &speed, &link_up, false); - if (!hw->fc.disable_fc_autoneg && hw->phy.multispeed_fiber && - (speed == IXGBE_LINK_SPEED_1GB_FULL)) - ret_val = ixgbe_fc_autoneg(hw); + reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); - if (ret_val) + /* + * The possible values of fc.requested_mode are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames, + * but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames but + * we do not support receiving pause frames). + * 3: Both Rx and Tx flow control (symmetric) are enabled. +#ifdef CONFIG_DCB + * 4: Priority Flow Control is enabled. +#endif + * other: Invalid. + */ + switch (hw->fc.requested_mode) { + case ixgbe_fc_none: + /* Flow control completely disabled by software override. */ + reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + break; + case ixgbe_fc_rx_pause: + /* + * Rx Flow control is enabled and Tx Flow control is + * disabled by software override. Since there really + * isn't a way to advertise that we are capable of RX + * Pause ONLY, we will advertise that we support both + * symmetric and asymmetric Rx PAUSE. Later, we will + * disable the adapter's ability to send PAUSE frames. + */ + reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + break; + case ixgbe_fc_tx_pause: + /* + * Tx Flow control is enabled, and Rx Flow control is + * disabled by software override. + */ + reg |= (IXGBE_PCS1GANA_ASM_PAUSE); + reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE); + break; + case ixgbe_fc_full: + /* Flow control (both Rx and Tx) is enabled by SW override. */ + reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + break; +#ifdef CONFIG_DCB + case ixgbe_fc_pfc: goto out; + break; +#endif /* CONFIG_DCB */ + default: + hw_dbg(hw, "Flow control param set incorrectly\n"); + ret_val = -IXGBE_ERR_CONFIG; + goto out; + break; + } + + IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg); + reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL); - ret_val = ixgbe_fc_enable(hw, packetbuf_num); + /* Enable and restart autoneg to inform the link partner */ + reg |= IXGBE_PCS1GLCTL_AN_ENABLE | IXGBE_PCS1GLCTL_AN_RESTART; + + /* Disable AN timeout */ + if (hw->fc.strict_ieee) + reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN; + + IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg); + hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg); out: return ret_val; diff --git a/drivers/net/ixgbe/ixgbe_common.h b/drivers/net/ixgbe/ixgbe_common.h index b2a4b2c99c4..0d34d4d8244 100644 --- a/drivers/net/ixgbe/ixgbe_common.h +++ b/drivers/net/ixgbe/ixgbe_common.h @@ -64,8 +64,8 @@ s32 ixgbe_update_uc_addr_list_generic(struct ixgbe_hw *hw, s32 ixgbe_enable_mc_generic(struct ixgbe_hw *hw); s32 ixgbe_disable_mc_generic(struct ixgbe_hw *hw); s32 ixgbe_enable_rx_dma_generic(struct ixgbe_hw *hw, u32 regval); -s32 ixgbe_setup_fc_generic(struct ixgbe_hw *hw, s32 packetbuf_num); -s32 ixgbe_fc_enable(struct ixgbe_hw *hw, s32 packtetbuf_num); +s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num); +s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw, s32 packtetbuf_num); s32 ixgbe_fc_autoneg(struct ixgbe_hw *hw); s32 ixgbe_validate_mac_addr(u8 *mac_addr); diff --git a/drivers/net/ixgbe/ixgbe_dcb_82599.c b/drivers/net/ixgbe/ixgbe_dcb_82599.c index f4417fc3b0f..589f62c7062 100644 --- a/drivers/net/ixgbe/ixgbe_dcb_82599.c +++ b/drivers/net/ixgbe/ixgbe_dcb_82599.c @@ -295,7 +295,7 @@ s32 ixgbe_dcb_config_pfc_82599(struct ixgbe_hw *hw, /* If PFC is disabled globally then fall back to LFC. */ if (!dcb_config->pfc_mode_enable) { for (i = 0; i < MAX_TRAFFIC_CLASS; i++) - hw->mac.ops.setup_fc(hw, i); + hw->mac.ops.fc_enable(hw, i); goto out; } diff --git a/drivers/net/ixgbe/ixgbe_ethtool.c b/drivers/net/ixgbe/ixgbe_ethtool.c index 583cc5a3c4f..1c110459d33 100644 --- a/drivers/net/ixgbe/ixgbe_ethtool.c +++ b/drivers/net/ixgbe/ixgbe_ethtool.c @@ -283,6 +283,7 @@ static int ixgbe_set_pauseparam(struct net_device *netdev, { struct ixgbe_adapter *adapter = netdev_priv(netdev); struct ixgbe_hw *hw = &adapter->hw; + struct ixgbe_fc_info fc; #ifdef CONFIG_DCB if (adapter->dcb_cfg.pfc_mode_enable || @@ -291,26 +292,37 @@ static int ixgbe_set_pauseparam(struct net_device *netdev, return -EINVAL; #endif + + fc = hw->fc; + if (pause->autoneg != AUTONEG_ENABLE) - hw->fc.disable_fc_autoneg = true; + fc.disable_fc_autoneg = true; else - hw->fc.disable_fc_autoneg = false; + fc.disable_fc_autoneg = false; if (pause->rx_pause && pause->tx_pause) - hw->fc.requested_mode = ixgbe_fc_full; + fc.requested_mode = ixgbe_fc_full; else if (pause->rx_pause && !pause->tx_pause) - hw->fc.requested_mode = ixgbe_fc_rx_pause; + fc.requested_mode = ixgbe_fc_rx_pause; else if (!pause->rx_pause && pause->tx_pause) - hw->fc.requested_mode = ixgbe_fc_tx_pause; + fc.requested_mode = ixgbe_fc_tx_pause; else if (!pause->rx_pause && !pause->tx_pause) - hw->fc.requested_mode = ixgbe_fc_none; + fc.requested_mode = ixgbe_fc_none; else return -EINVAL; #ifdef CONFIG_DCB - adapter->last_lfc_mode = hw->fc.requested_mode; + adapter->last_lfc_mode = fc.requested_mode; #endif - hw->mac.ops.setup_fc(hw, 0); + + /* if the thing changed then we'll update and use new autoneg */ + if (memcmp(&fc, &hw->fc, sizeof(struct ixgbe_fc_info))) { + hw->fc = fc; + if (netif_running(netdev)) + ixgbe_reinit_locked(adapter); + else + ixgbe_reset(adapter); + } return 0; } diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index 0a3e8a35a0b..9684632f15b 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -4344,12 +4344,12 @@ static void ixgbe_watchdog_task(struct work_struct *work) #ifdef CONFIG_DCB if (adapter->flags & IXGBE_FLAG_DCB_ENABLED) { for (i = 0; i < MAX_TRAFFIC_CLASS; i++) - hw->mac.ops.setup_fc(hw, i); + hw->mac.ops.fc_enable(hw, i); } else { - hw->mac.ops.setup_fc(hw, 0); + hw->mac.ops.fc_enable(hw, 0); } #else - hw->mac.ops.setup_fc(hw, 0); + hw->mac.ops.fc_enable(hw, 0); #endif } diff --git a/drivers/net/ixgbe/ixgbe_type.h b/drivers/net/ixgbe/ixgbe_type.h index 199b288c345..4402552eb3e 100644 --- a/drivers/net/ixgbe/ixgbe_type.h +++ b/drivers/net/ixgbe/ixgbe_type.h @@ -1368,8 +1368,6 @@ #define IXGBE_LINK_UP_TIME 90 /* 9.0 Seconds */ #define IXGBE_AUTO_NEG_TIME 45 /* 4.5 Seconds */ -#define FIBER_LINK_UP_LIMIT 50 - /* PCS1GLSTA Bit Masks */ #define IXGBE_PCS1GLSTA_LINK_OK 1 #define IXGBE_PCS1GLSTA_SYNK_OK 0x10 @@ -2094,7 +2092,8 @@ struct ixgbe_fc_info { u16 pause_time; /* Flow Control Pause timer */ bool send_xon; /* Flow control send XON */ bool strict_ieee; /* Strict IEEE mode */ - bool disable_fc_autoneg; /* Turn off autoneg FC mode */ + bool disable_fc_autoneg; /* Do not autonegotiate FC */ + bool fc_was_autonegged; /* Is current_mode the result of autonegging? */ enum ixgbe_fc_mode current_mode; /* FC mode in effect */ enum ixgbe_fc_mode requested_mode; /* FC mode requested by caller */ }; @@ -2236,7 +2235,7 @@ struct ixgbe_mac_operations { s32 (*init_uta_tables)(struct ixgbe_hw *); /* Flow Control */ - s32 (*setup_fc)(struct ixgbe_hw *, s32); + s32 (*fc_enable)(struct ixgbe_hw *, s32); }; struct ixgbe_phy_operations { |