[IA64] remove time interpolator

Remove time_interpolator code (This is generic code, but
only user was ia64.  It has been superseded by the
CONFIG_GENERIC_TIME code).

Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Peter Keilty <peter.keilty@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

1 files changed, 0 insertions, 60 deletions

diff --git a/include/linux/timex.h b/include/linux/timex.h
index da929dbbea2..37ac3ff90fa 100644
--- a/include/linux/timex.h
+++ b/include/linux/timex.h
@@ -224,66 +224,6 @@ static inline int ntp_synced(void)
 	__x < 0 ? -(-__x >> __s) : __x >> __s;	\
 })
 
-
-#ifdef CONFIG_TIME_INTERPOLATION
-
-#define TIME_SOURCE_CPU 0
-#define TIME_SOURCE_MMIO64 1
-#define TIME_SOURCE_MMIO32 2
-#define TIME_SOURCE_FUNCTION 3
-
-/* For proper operations time_interpolator clocks must run slightly slower
- * than the standard clock since the interpolator may only correct by having
- * time jump forward during a tick. A slower clock is usually a side effect
- * of the integer divide of the nanoseconds in a second by the frequency.
- * The accuracy of the division can be increased by specifying a shift.
- * However, this may cause the clock not to be slow enough.
- * The interpolator will self-tune the clock by slowing down if no
- * resets occur or speeding up if the time jumps per analysis cycle
- * become too high.
- *
- * Setting jitter compensates for a fluctuating timesource by comparing
- * to the last value read from the timesource to insure that an earlier value
- * is not returned by a later call. The price to pay
- * for the compensation is that the timer routines are not as scalable anymore.
- */
-
-struct time_interpolator {
-	u16 source;			/* time source flags */
-	u8 shift;			/* increases accuracy of multiply by shifting. */
-				/* Note that bits may be lost if shift is set too high */
-	u8 jitter;			/* if set compensate for fluctuations */
-	u32 nsec_per_cyc;		/* set by register_time_interpolator() */
-	void *addr;			/* address of counter or function */
-	cycles_t mask;			/* mask the valid bits of the counter */
-	unsigned long offset;		/* nsec offset at last update of interpolator */
-	u64 last_counter;		/* counter value in units of the counter at last update */
-	cycles_t last_cycle;		/* Last timer value if TIME_SOURCE_JITTER is set */
-	u64 frequency;			/* frequency in counts/second */
-	long drift;			/* drift in parts-per-million (or -1) */
-	unsigned long skips;		/* skips forward */
-	unsigned long ns_skipped;	/* nanoseconds skipped */
-	struct time_interpolator *next;
-};
-
-extern void register_time_interpolator(struct time_interpolator *);
-extern void unregister_time_interpolator(struct time_interpolator *);
-extern void time_interpolator_reset(void);
-extern unsigned long time_interpolator_get_offset(void);
-extern void time_interpolator_update(long delta_nsec);
-
-#else /* !CONFIG_TIME_INTERPOLATION */
-
-static inline void time_interpolator_reset(void)
-{
-}
-
-static inline void time_interpolator_update(long delta_nsec)
-{
-}
-
-#endif /* !CONFIG_TIME_INTERPOLATION */
-
 #define TICK_LENGTH_SHIFT	32
 
 #ifdef CONFIG_NO_HZ