Merge branch 'dmaengine' into async-tx-next

Conflicts:
	crypto/async_tx/async_xor.c
	drivers/dma/ioat/dma_v2.h
	drivers/dma/ioat/pci.c
	drivers/md/raid5.c

1 files changed, 17 insertions, 1078 deletions

diff --git a/arch/powerpc/kernel/head_64.S b/arch/powerpc/kernel/head_64.S
index 50ef505b8fb..012505ebd9f 100644
--- a/arch/powerpc/kernel/head_64.S
+++ b/arch/powerpc/kernel/head_64.S
@@ -12,8 +12,9 @@
  *  Adapted for 64bit PowerPC by Dave Engebretsen, Peter Bergner, and
  *    Mike Corrigan {engebret|bergner|mikejc}@us.ibm.com
  *
- *  This file contains the low-level support and setup for the
- *  PowerPC-64 platform, including trap and interrupt dispatch.
+ *  This file contains the entry point for the 64-bit kernel along
+ *  with some early initialization code common to all 64-bit powerpc
+ *  variants.
  *
  *  This program is free software; you can redistribute it and/or
  *  modify it under the terms of the GNU General Public License
@@ -38,36 +39,25 @@
 #include <asm/exception.h>
 #include <asm/irqflags.h>
 
-/*
- * We layout physical memory as follows:
- * 0x0000 - 0x00ff : Secondary processor spin code
- * 0x0100 - 0x2fff : pSeries Interrupt prologs
- * 0x3000 - 0x5fff : interrupt support, iSeries and common interrupt prologs
- * 0x6000 - 0x6fff : Initial (CPU0) segment table
- * 0x7000 - 0x7fff : FWNMI data area
- * 0x8000 -        : Early init and support code
- */
-
-/*
- *   SPRG Usage
- *
- *   Register	Definition
- *
- *   SPRG0	reserved for hypervisor
- *   SPRG1	temp - used to save gpr
- *   SPRG2	temp - used to save gpr
- *   SPRG3	virt addr of paca
+/* The physical memory is layed out such that the secondary processor
+ * spin code sits at 0x0000...0x00ff. On server, the vectors follow
+ * using the layout described in exceptions-64s.S
  */
 
 /*
  * Entering into this code we make the following assumptions:
- *  For pSeries:
+ *
+ *  For pSeries or server processors:
  *   1. The MMU is off & open firmware is running in real mode.
  *   2. The kernel is entered at __start
  *
  *  For iSeries:
  *   1. The MMU is on (as it always is for iSeries)
  *   2. The kernel is entered at system_reset_iSeries
+ *
+ *  For Book3E processors:
+ *   1. The MMU is on running in AS0 in a state defined in ePAPR
+ *   2. The kernel is entered at __start
  */
 
 	.text
@@ -166,1065 +156,14 @@ exception_marker:
 	.text
 
 /*
- * This is the start of the interrupt handlers for pSeries
- * This code runs with relocation off.
- * Code from here to __end_interrupts gets copied down to real
- * address 0x100 when we are running a relocatable kernel.
- * Therefore any relative branches in this section must only
- * branch to labels in this section.
- */
-	. = 0x100
-	.globl __start_interrupts
-__start_interrupts:
-
-	STD_EXCEPTION_PSERIES(0x100, system_reset)
-
-	. = 0x200
-_machine_check_pSeries:
-	HMT_MEDIUM
-	mtspr	SPRN_SPRG1,r13		/* save r13 */
-	EXCEPTION_PROLOG_PSERIES(PACA_EXMC, machine_check_common)
-
-	. = 0x300
-	.globl data_access_pSeries
-data_access_pSeries:
-	HMT_MEDIUM
-	mtspr	SPRN_SPRG1,r13
-BEGIN_FTR_SECTION
-	mtspr	SPRN_SPRG2,r12
-	mfspr	r13,SPRN_DAR
-	mfspr	r12,SPRN_DSISR
-	srdi	r13,r13,60
-	rlwimi	r13,r12,16,0x20
-	mfcr	r12
-	cmpwi	r13,0x2c
-	beq	do_stab_bolted_pSeries
-	mtcrf	0x80,r12
-	mfspr	r12,SPRN_SPRG2
-END_FTR_SECTION_IFCLR(CPU_FTR_SLB)
-	EXCEPTION_PROLOG_PSERIES(PACA_EXGEN, data_access_common)
-
-	. = 0x380
-	.globl data_access_slb_pSeries
-data_access_slb_pSeries:
-	HMT_MEDIUM
-	mtspr	SPRN_SPRG1,r13
-	mfspr	r13,SPRN_SPRG3		/* get paca address into r13 */
-	std	r3,PACA_EXSLB+EX_R3(r13)
-	mfspr	r3,SPRN_DAR
-	std	r9,PACA_EXSLB+EX_R9(r13)	/* save r9 - r12 */
-	mfcr	r9
-#ifdef __DISABLED__
-	/* Keep that around for when we re-implement dynamic VSIDs */
-	cmpdi	r3,0
-	bge	slb_miss_user_pseries
-#endif /* __DISABLED__ */
-	std	r10,PACA_EXSLB+EX_R10(r13)
-	std	r11,PACA_EXSLB+EX_R11(r13)
-	std	r12,PACA_EXSLB+EX_R12(r13)
-	mfspr	r10,SPRN_SPRG1
-	std	r10,PACA_EXSLB+EX_R13(r13)
-	mfspr	r12,SPRN_SRR1		/* and SRR1 */
-#ifndef CONFIG_RELOCATABLE
-	b	.slb_miss_realmode
-#else
-	/*
-	 * We can't just use a direct branch to .slb_miss_realmode
-	 * because the distance from here to there depends on where
-	 * the kernel ends up being put.
-	 */
-	mfctr	r11
-	ld	r10,PACAKBASE(r13)
-	LOAD_HANDLER(r10, .slb_miss_realmode)
-	mtctr	r10
-	bctr
-#endif
-
-	STD_EXCEPTION_PSERIES(0x400, instruction_access)
-
-	. = 0x480
-	.globl instruction_access_slb_pSeries
-instruction_access_slb_pSeries:
-	HMT_MEDIUM
-	mtspr	SPRN_SPRG1,r13
-	mfspr	r13,SPRN_SPRG3		/* get paca address into r13 */
-	std	r3,PACA_EXSLB+EX_R3(r13)
-	mfspr	r3,SPRN_SRR0		/* SRR0 is faulting address */
-	std	r9,PACA_EXSLB+EX_R9(r13)	/* save r9 - r12 */
-	mfcr	r9
-#ifdef __DISABLED__
-	/* Keep that around for when we re-implement dynamic VSIDs */
-	cmpdi	r3,0
-	bge	slb_miss_user_pseries
-#endif /* __DISABLED__ */
-	std	r10,PACA_EXSLB+EX_R10(r13)
-	std	r11,PACA_EXSLB+EX_R11(r13)
-	std	r12,PACA_EXSLB+EX_R12(r13)
-	mfspr	r10,SPRN_SPRG1
-	std	r10,PACA_EXSLB+EX_R13(r13)
-	mfspr	r12,SPRN_SRR1		/* and SRR1 */
-#ifndef CONFIG_RELOCATABLE
-	b	.slb_miss_realmode
-#else
-	mfctr	r11
-	ld	r10,PACAKBASE(r13)
-	LOAD_HANDLER(r10, .slb_miss_realmode)
-	mtctr	r10
-	bctr
-#endif
-
-	MASKABLE_EXCEPTION_PSERIES(0x500, hardware_interrupt)
-	STD_EXCEPTION_PSERIES(0x600, alignment)
-	STD_EXCEPTION_PSERIES(0x700, program_check)
-	STD_EXCEPTION_PSERIES(0x800, fp_unavailable)
-	MASKABLE_EXCEPTION_PSERIES(0x900, decrementer)
-	STD_EXCEPTION_PSERIES(0xa00, trap_0a)
-	STD_EXCEPTION_PSERIES(0xb00, trap_0b)
-
-	. = 0xc00
-	.globl	system_call_pSeries
-system_call_pSeries:
-	HMT_MEDIUM
-BEGIN_FTR_SECTION
-	cmpdi	r0,0x1ebe
-	beq-	1f
-END_FTR_SECTION_IFSET(CPU_FTR_REAL_LE)
-	mr	r9,r13
-	mfspr	r13,SPRN_SPRG3
-	mfspr	r11,SPRN_SRR0
-	ld	r12,PACAKBASE(r13)
-	ld	r10,PACAKMSR(r13)
-	LOAD_HANDLER(r12, system_call_entry)
-	mtspr	SPRN_SRR0,r12
-	mfspr	r12,SPRN_SRR1
-	mtspr	SPRN_SRR1,r10
-	rfid
-	b	.	/* prevent speculative execution */
-
-/* Fast LE/BE switch system call */
-1:	mfspr	r12,SPRN_SRR1
-	xori	r12,r12,MSR_LE
-	mtspr	SPRN_SRR1,r12
-	rfid		/* return to userspace */
-	b	.
-
-	STD_EXCEPTION_PSERIES(0xd00, single_step)
-	STD_EXCEPTION_PSERIES(0xe00, trap_0e)
-
-	/* We need to deal with the Altivec unavailable exception
-	 * here which is at 0xf20, thus in the middle of the
-	 * prolog code of the PerformanceMonitor one. A little
-	 * trickery is thus necessary
-	 */
-	. = 0xf00
-	b	performance_monitor_pSeries
-
-	. = 0xf20
-	b	altivec_unavailable_pSeries
-
-	. = 0xf40
-	b	vsx_unavailable_pSeries
-
-#ifdef CONFIG_CBE_RAS
-	HSTD_EXCEPTION_PSERIES(0x1200, cbe_system_error)
-#endif /* CONFIG_CBE_RAS */
-	STD_EXCEPTION_PSERIES(0x1300, instruction_breakpoint)
-#ifdef CONFIG_CBE_RAS
-	HSTD_EXCEPTION_PSERIES(0x1600, cbe_maintenance)
-#endif /* CONFIG_CBE_RAS */
-	STD_EXCEPTION_PSERIES(0x1700, altivec_assist)
-#ifdef CONFIG_CBE_RAS
-	HSTD_EXCEPTION_PSERIES(0x1800, cbe_thermal)
-#endif /* CONFIG_CBE_RAS */
-
-	. = 0x3000
-
-/*** pSeries interrupt support ***/
-
-	/* moved from 0xf00 */
-	STD_EXCEPTION_PSERIES(., performance_monitor)
-	STD_EXCEPTION_PSERIES(., altivec_unavailable)
-	STD_EXCEPTION_PSERIES(., vsx_unavailable)
-
-/*
- * An interrupt came in while soft-disabled; clear EE in SRR1,
- * clear paca->hard_enabled and return.
- */
-masked_interrupt:
-	stb	r10,PACAHARDIRQEN(r13)
-	mtcrf	0x80,r9
-	ld	r9,PACA_EXGEN+EX_R9(r13)
-	mfspr	r10,SPRN_SRR1
-	rldicl	r10,r10,48,1		/* clear MSR_EE */
-	rotldi	r10,r10,16
-	mtspr	SPRN_SRR1,r10
-	ld	r10,PACA_EXGEN+EX_R10(r13)
-	mfspr	r13,SPRN_SPRG1
-	rfid
-	b	.
-
-	.align	7
-do_stab_bolted_pSeries:
-	mtcrf	0x80,r12
-	mfspr	r12,SPRN_SPRG2
-	EXCEPTION_PROLOG_PSERIES(PACA_EXSLB, .do_stab_bolted)
-
-#ifdef CONFIG_PPC_PSERIES
-/*
- * Vectors for the FWNMI option.  Share common code.
- */
-	.globl system_reset_fwnmi
-      .align 7
-system_reset_fwnmi:
-	HMT_MEDIUM
-	mtspr	SPRN_SPRG1,r13		/* save r13 */
-	EXCEPTION_PROLOG_PSERIES(PACA_EXGEN, system_reset_common)
-
-	.globl machine_check_fwnmi
-      .align 7
-machine_check_fwnmi:
-	HMT_MEDIUM
-	mtspr	SPRN_SPRG1,r13		/* save r13 */
-	EXCEPTION_PROLOG_PSERIES(PACA_EXMC, machine_check_common)
-
-#endif /* CONFIG_PPC_PSERIES */
-
-#ifdef __DISABLED__
-/*
- * This is used for when the SLB miss handler has to go virtual,
- * which doesn't happen for now anymore but will once we re-implement
- * dynamic VSIDs for shared page tables
- */
-slb_miss_user_pseries:
-	std	r10,PACA_EXGEN+EX_R10(r13)
-	std	r11,PACA_EXGEN+EX_R11(r13)
-	std	r12,PACA_EXGEN+EX_R12(r13)
-	mfspr	r10,SPRG1
-	ld	r11,PACA_EXSLB+EX_R9(r13)
-	ld	r12,PACA_EXSLB+EX_R3(r13)
-	std	r10,PACA_EXGEN+EX_R13(r13)
-	std	r11,PACA_EXGEN+EX_R9(r13)
-	std	r12,PACA_EXGEN+EX_R3(r13)
-	clrrdi	r12,r13,32
-	mfmsr	r10
-	mfspr	r11,SRR0			/* save SRR0 */
-	ori	r12,r12,slb_miss_user_common@l	/* virt addr of handler */
-	ori	r10,r10,MSR_IR|MSR_DR|MSR_RI
-	mtspr	SRR0,r12
-	mfspr	r12,SRR1			/* and SRR1 */
-	mtspr	SRR1,r10
-	rfid
-	b	.				/* prevent spec. execution */
-#endif /* __DISABLED__ */
-
-	.align	7
-	.globl	__end_interrupts
-__end_interrupts:
-
-/*
- * Code from here down to __end_handlers is invoked from the
- * exception prologs above.  Because the prologs assemble the
- * addresses of these handlers using the LOAD_HANDLER macro,
- * which uses an addi instruction, these handlers must be in
- * the first 32k of the kernel image.
- */
-
-/*** Common interrupt handlers ***/
-
-	STD_EXCEPTION_COMMON(0x100, system_reset, .system_reset_exception)
-
-	/*
-	 * Machine check is different because we use a different
-	 * save area: PACA_EXMC instead of PACA_EXGEN.
-	 */
-	.align	7
-	.globl machine_check_common
-machine_check_common:
-	EXCEPTION_PROLOG_COMMON(0x200, PACA_EXMC)
-	FINISH_NAP
-	DISABLE_INTS
-	bl	.save_nvgprs
-	addi	r3,r1,STACK_FRAME_OVERHEAD
-	bl	.machine_check_exception
-	b	.ret_from_except
-
-	STD_EXCEPTION_COMMON_LITE(0x900, decrementer, .timer_interrupt)
-	STD_EXCEPTION_COMMON(0xa00, trap_0a, .unknown_exception)
-	STD_EXCEPTION_COMMON(0xb00, trap_0b, .unknown_exception)
-	STD_EXCEPTION_COMMON(0xd00, single_step, .single_step_exception)
-	STD_EXCEPTION_COMMON(0xe00, trap_0e, .unknown_exception)
-	STD_EXCEPTION_COMMON_IDLE(0xf00, performance_monitor, .performance_monitor_exception)
-	STD_EXCEPTION_COMMON(0x1300, instruction_breakpoint, .instruction_breakpoint_exception)
-#ifdef CONFIG_ALTIVEC
-	STD_EXCEPTION_COMMON(0x1700, altivec_assist, .altivec_assist_exception)
-#else
-	STD_EXCEPTION_COMMON(0x1700, altivec_assist, .unknown_exception)
-#endif
-#ifdef CONFIG_CBE_RAS
-	STD_EXCEPTION_COMMON(0x1200, cbe_system_error, .cbe_system_error_exception)
-	STD_EXCEPTION_COMMON(0x1600, cbe_maintenance, .cbe_maintenance_exception)
-	STD_EXCEPTION_COMMON(0x1800, cbe_thermal, .cbe_thermal_exception)
-#endif /* CONFIG_CBE_RAS */
-
-	.align	7
-system_call_entry:
-	b	system_call_common
-
-/*
- * Here we have detected that the kernel stack pointer is bad.
- * R9 contains the saved CR, r13 points to the paca,
- * r10 contains the (bad) kernel stack pointer,
- * r11 and r12 contain the saved SRR0 and SRR1.
- * We switch to using an emergency stack, save the registers there,
- * and call kernel_bad_stack(), which panics.
- */
-bad_stack:
-	ld	r1,PACAEMERGSP(r13)
-	subi	r1,r1,64+INT_FRAME_SIZE
-	std	r9,_CCR(r1)
-	std	r10,GPR1(r1)
-	std	r11,_NIP(r1)
-	std	r12,_MSR(r1)
-	mfspr	r11,SPRN_DAR
-	mfspr	r12,SPRN_DSISR
-	std	r11,_DAR(r1)
-	std	r12,_DSISR(r1)
-	mflr	r10
-	mfctr	r11
-	mfxer	r12
-	std	r10,_LINK(r1)
-	std	r11,_CTR(r1)
-	std	r12,_XER(r1)
-	SAVE_GPR(0,r1)
-	SAVE_GPR(2,r1)
-	SAVE_4GPRS(3,r1)
-	SAVE_2GPRS(7,r1)
-	SAVE_10GPRS(12,r1)
-	SAVE_10GPRS(22,r1)
-	lhz	r12,PACA_TRAP_SAVE(r13)
-	std	r12,_TRAP(r1)
-	addi	r11,r1,INT_FRAME_SIZE
-	std	r11,0(r1)
-	li	r12,0
-	std	r12,0(r11)
-	ld	r2,PACATOC(r13)
-1:	addi	r3,r1,STACK_FRAME_OVERHEAD
-	bl	.kernel_bad_stack
-	b	1b
-
-/*
- * Here r13 points to the paca, r9 contains the saved CR,
- * SRR0 and SRR1 are saved in r11 and r12,
- * r9 - r13 are saved in paca->exgen.
- */
-	.align	7
-	.globl data_access_common
-data_access_common:
-	mfspr	r10,SPRN_DAR
-	std	r10,PACA_EXGEN+EX_DAR(r13)
-	mfspr	r10,SPRN_DSISR
-	stw	r10,PACA_EXGEN+EX_DSISR(r13)
-	EXCEPTION_PROLOG_COMMON(0x300, PACA_EXGEN)
-	ld	r3,PACA_EXGEN+EX_DAR(r13)
-	lwz	r4,PACA_EXGEN+EX_DSISR(r13)
-	li	r5,0x300
-	b	.do_hash_page	 	/* Try to handle as hpte fault */
-
-	.align	7
-	.globl instruction_access_common
-instruction_access_common:
-	EXCEPTION_PROLOG_COMMON(0x400, PACA_EXGEN)
-	ld	r3,_NIP(r1)
-	andis.	r4,r12,0x5820
-	li	r5,0x400
-	b	.do_hash_page		/* Try to handle as hpte fault */
-
-/*
- * Here is the common SLB miss user that is used when going to virtual
- * mode for SLB misses, that is currently not used
- */
-#ifdef __DISABLED__
-	.align	7
-	.globl	slb_miss_user_common
-slb_miss_user_common:
-	mflr	r10
-	std	r3,PACA_EXGEN+EX_DAR(r13)
-	stw	r9,PACA_EXGEN+EX_CCR(r13)
-	std	r10,PACA_EXGEN+EX_LR(r13)
-	std	r11,PACA_EXGEN+EX_SRR0(r13)
-	bl	.slb_allocate_user
-
-	ld	r10,PACA_EXGEN+EX_LR(r13)
-	ld	r3,PACA_EXGEN+EX_R3(r13)
-	lwz	r9,PACA_EXGEN+EX_CCR(r13)
-	ld	r11,PACA_EXGEN+EX_SRR0(r13)
-	mtlr	r10
-	beq-	slb_miss_fault
-
-	andi.	r10,r12,MSR_RI		/* check for unrecoverable exception */
-	beq-	unrecov_user_slb
-	mfmsr	r10
-
-.machine push
-.machine "power4"
-	mtcrf	0x80,r9
-.machine pop
-
-	clrrdi	r10,r10,2		/* clear RI before setting SRR0/1 */
-	mtmsrd	r10,1
-
-	mtspr	SRR0,r11
-	mtspr	SRR1,r12
-
-	ld	r9,PACA_EXGEN+EX_R9(r13)
-	ld	r10,PACA_EXGEN+EX_R10(r13)
-	ld	r11,PACA_EXGEN+EX_R11(r13)
-	ld	r12,PACA_EXGEN+EX_R12(r13)
-	ld	r13,PACA_EXGEN+EX_R13(r13)
-	rfid
-	b	.
-
-slb_miss_fault:
-	EXCEPTION_PROLOG_COMMON(0x380, PACA_EXGEN)
-	ld	r4,PACA_EXGEN+EX_DAR(r13)
-	li	r5,0
-	std	r4,_DAR(r1)
-	std	r5,_DSISR(r1)
-	b	handle_page_fault
-
-unrecov_user_slb:
-	EXCEPTION_PROLOG_COMMON(0x4200, PACA_EXGEN)
-	DISABLE_INTS
-	bl	.save_nvgprs
-1:	addi	r3,r1,STACK_FRAME_OVERHEAD
-	bl	.unrecoverable_exception
-	b	1b
-
-#endif /* __DISABLED__ */
-
-
-/*
- * r13 points to the PACA, r9 contains the saved CR,
- * r12 contain the saved SRR1, SRR0 is still ready for return
- * r3 has the faulting address
- * r9 - r13 are saved in paca->exslb.
- * r3 is saved in paca->slb_r3
- * We assume we aren't going to take any exceptions during this procedure.
- */
-_GLOBAL(slb_miss_realmode)
-	mflr	r10
-#ifdef CONFIG_RELOCATABLE
-	mtctr	r11
-#endif
-
-	stw	r9,PACA_EXSLB+EX_CCR(r13)	/* save CR in exc. frame */
-	std	r10,PACA_EXSLB+EX_LR(r13)	/* save LR */
-
-	bl	.slb_allocate_realmode
-
-	/* All done -- return from exception. */
-
-	ld	r10,PACA_EXSLB+EX_LR(r13)
-	ld	r3,PACA_EXSLB+EX_R3(r13)
-	lwz	r9,PACA_EXSLB+EX_CCR(r13)	/* get saved CR */
-#ifdef CONFIG_PPC_ISERIES
-BEGIN_FW_FTR_SECTION
-	ld	r11,PACALPPACAPTR(r13)
-	ld	r11,LPPACASRR0(r11)		/* get SRR0 value */
-END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES)
-#endif /* CONFIG_PPC_ISERIES */
-
-	mtlr	r10
-
-	andi.	r10,r12,MSR_RI	/* check for unrecoverable exception */
-	beq-	2f
-
-.machine	push
-.machine	"power4"
-	mtcrf	0x80,r9
-	mtcrf	0x01,r9		/* slb_allocate uses cr0 and cr7 */
-.machine	pop
-
-#ifdef CONFIG_PPC_ISERIES
-BEGIN_FW_FTR_SECTION
-	mtspr	SPRN_SRR0,r11
-	mtspr	SPRN_SRR1,r12
-END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES)
-#endif /* CONFIG_PPC_ISERIES */
-	ld	r9,PACA_EXSLB+EX_R9(r13)
-	ld	r10,PACA_EXSLB+EX_R10(r13)
-	ld	r11,PACA_EXSLB+EX_R11(r13)
-	ld	r12,PACA_EXSLB+EX_R12(r13)
-	ld	r13,PACA_EXSLB+EX_R13(r13)
-	rfid
-	b	.	/* prevent speculative execution */
-
-2:
-#ifdef CONFIG_PPC_ISERIES
-BEGIN_FW_FTR_SECTION
-	b	unrecov_slb
-END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES)
-#endif /* CONFIG_PPC_ISERIES */
-	mfspr	r11,SPRN_SRR0
-	ld	r10,PACAKBASE(r13)
-	LOAD_HANDLER(r10,unrecov_slb)
-	mtspr	SPRN_SRR0,r10
-	ld	r10,PACAKMSR(r13)
-	mtspr	SPRN_SRR1,r10
-	rfid
-	b	.
-
-unrecov_slb:
-	EXCEPTION_PROLOG_COMMON(0x4100, PACA_EXSLB)
-	DISABLE_INTS
-	bl	.save_nvgprs
-1:	addi	r3,r1,STACK_FRAME_OVERHEAD
-	bl	.unrecoverable_exception
-	b	1b
-
-	.align	7
-	.globl hardware_interrupt_common
-	.globl hardware_interrupt_entry
-hardware_interrupt_common:
-	EXCEPTION_PROLOG_COMMON(0x500, PACA_EXGEN)
-	FINISH_NAP
-hardware_interrupt_entry:
-	DISABLE_INTS
-BEGIN_FTR_SECTION
-	bl	.ppc64_runlatch_on
-END_FTR_SECTION_IFSET(CPU_FTR_CTRL)
-	addi	r3,r1,STACK_FRAME_OVERHEAD
-	bl	.do_IRQ
-	b	.ret_from_except_lite
-
-#ifdef CONFIG_PPC_970_NAP
-power4_fixup_nap:
-	andc	r9,r9,r10
-	std	r9,TI_LOCAL_FLAGS(r11)
-	ld	r10,_LINK(r1)		/* make idle task do the */
-	std	r10,_NIP(r1)		/* equivalent of a blr */
-	blr
-#endif
-
-	.align	7
-	.globl alignment_common
-alignment_common:
-	mfspr	r10,SPRN_DAR
-	std	r10,PACA_EXGEN+EX_DAR(r13)
-	mfspr	r10,SPRN_DSISR
-	stw	r10,PACA_EXGEN+EX_DSISR(r13)
-	EXCEPTION_PROLOG_COMMON(0x600, PACA_EXGEN)
-	ld	r3,PACA_EXGEN+EX_DAR(r13)
-	lwz	r4,PACA_EXGEN+EX_DSISR(r13)
-	std	r3,_DAR(r1)
-	std	r4,_DSISR(r1)
-	bl	.save_nvgprs
-	addi	r3,r1,STACK_FRAME_OVERHEAD
-	ENABLE_INTS
-	bl	.alignment_exception
-	b	.ret_from_except
-
-	.align	7
-	.globl program_check_common
-program_check_common:
-	EXCEPTION_PROLOG_COMMON(0x700, PACA_EXGEN)
-	bl	.save_nvgprs
-	addi	r3,r1,STACK_FRAME_OVERHEAD
-	ENABLE_INTS
-	bl	.program_check_exception
-	b	.ret_from_except
-
-	.align	7
-	.globl fp_unavailable_common
-fp_unavailable_common:
-	EXCEPTION_PROLOG_COMMON(0x800, PACA_EXGEN)
-	bne	1f			/* if from user, just load it up */
-	bl	.save_nvgprs
-	addi	r3,r1,STACK_FRAME_OVERHEAD
-	ENABLE_INTS
-	bl	.kernel_fp_unavailable_exception
-	BUG_OPCODE
-1:	bl	.load_up_fpu
-	b	fast_exception_return
-
-	.align	7
-	.globl altivec_unavailable_common
-altivec_unavailable_common:
-	EXCEPTION_PROLOG_COMMON(0xf20, PACA_EXGEN)
-#ifdef CONFIG_ALTIVEC
-BEGIN_FTR_SECTION
-	beq	1f
-	bl	.load_up_altivec
-	b	fast_exception_return
-1:
-END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC)
-#endif
-	bl	.save_nvgprs
-	addi	r3,r1,STACK_FRAME_OVERHEAD
-	ENABLE_INTS
-	bl	.altivec_unavailable_exception
-	b	.ret_from_except
-
-	.align	7
-	.globl vsx_unavailable_common
-vsx_unavailable_common:
-	EXCEPTION_PROLOG_COMMON(0xf40, PACA_EXGEN)
-#ifdef CONFIG_VSX
-BEGIN_FTR_SECTION
-	bne	.load_up_vsx
-1:
-END_FTR_SECTION_IFSET(CPU_FTR_VSX)
-#endif
-	bl	.save_nvgprs
-	addi	r3,r1,STACK_FRAME_OVERHEAD
-	ENABLE_INTS
-	bl	.vsx_unavailable_exception
-	b	.ret_from_except
-
-	.align	7
-	.globl	__end_handlers
-__end_handlers:
-
-/*
- * Return from an exception with minimal checks.
- * The caller is assumed to have done EXCEPTION_PROLOG_COMMON.
- * If interrupts have been enabled, or anything has been
- * done that might have changed the scheduling status of
- * any task or sent any task a signal, you should use
- * ret_from_except or ret_from_except_lite instead of this.
+ * On server, we include the exception vectors code here as it
+ * relies on absolute addressing which is only possible within
+ * this compilation unit
  */
-fast_exc_return_irq:			/* restores irq state too */
-	ld	r3,SOFTE(r1)
-	TRACE_AND_RESTORE_IRQ(r3);
-	ld	r12,_MSR(r1)
-	rldicl	r4,r12,49,63		/* get MSR_EE to LSB */
-	stb	r4,PACAHARDIRQEN(r13)	/* restore paca->hard_enabled */
-	b	1f
-
-	.globl	fast_exception_return
-fast_exception_return:
-	ld	r12,_MSR(r1)
-1:	ld	r11,_NIP(r1)
-	andi.	r3,r12,MSR_RI		/* check if RI is set */
-	beq-	unrecov_fer
-
-#ifdef CONFIG_VIRT_CPU_ACCOUNTING
-	andi.	r3,r12,MSR_PR
-	beq	2f
-	ACCOUNT_CPU_USER_EXIT(r3, r4)
-2:
+#ifdef CONFIG_PPC_BOOK3S
+#include "exceptions-64s.S"
 #endif
 
-	ld	r3,_CCR(r1)
-	ld	r4,_LINK(r1)
-	ld	r5,_CTR(r1)
-	ld	r6,_XER(r1)
-	mtcr	r3
-	mtlr	r4
-	mtctr	r5
-	mtxer	r6
-	REST_GPR(0, r1)
-	REST_8GPRS(2, r1)
-
-	mfmsr	r10
-	rldicl	r10,r10,48,1		/* clear EE */
-	rldicr	r10,r10,16,61		/* clear RI (LE is 0 already) */
-	mtmsrd	r10,1
-
-	mtspr	SPRN_SRR1,r12
-	mtspr	SPRN_SRR0,r11
-	REST_4GPRS(10, r1)
-	ld	r1,GPR1(r1)
-	rfid
-	b	.	/* prevent speculative execution */
-
-unrecov_fer:
-	bl	.save_nvgprs
-1:	addi	r3,r1,STACK_FRAME_OVERHEAD
-	bl	.unrecoverable_exception
-	b	1b
-
-#ifdef CONFIG_ALTIVEC
-/*
- * load_up_altivec(unused, unused, tsk)
- * Disable VMX for the task which had it previously,
- * and save its vector registers in its thread_struct.
- * Enables the VMX for use in the kernel on return.
- * On SMP we know the VMX is free, since we give it up every
- * switch (ie, no lazy save of the vector registers).
- * On entry: r13 == 'current' && last_task_used_altivec != 'current'
- */
-_STATIC(load_up_altivec)
-	mfmsr	r5			/* grab the current MSR */
-	oris	r5,r5,MSR_VEC@h
-	mtmsrd	r5			/* enable use of VMX now */
-	isync
-
-/*
- * For SMP, we don't do lazy VMX switching because it just gets too
- * horrendously complex, especially when a task switches from one CPU
- * to another.  Instead we call giveup_altvec in switch_to.
- * VRSAVE isn't dealt with here, that is done in the normal context
- * switch code. Note that we could rely on vrsave value to eventually
- * avoid saving all of the VREGs here...
- */
-#ifndef CONFIG_SMP
-	ld	r3,last_task_used_altivec@got(r2)
-	ld	r4,0(r3)
-	cmpdi	0,r4,0
-	beq	1f
-	/* Save VMX state to last_task_used_altivec's THREAD struct */
-	addi	r4,r4,THREAD
-	SAVE_32VRS(0,r5,r4)
-	mfvscr	vr0
-	li	r10,THREAD_VSCR
-	stvx	vr0,r10,r4
-	/* Disable VMX for last_task_used_altivec */
-	ld	r5,PT_REGS(r4)
-	ld	r4,_MSR-STACK_FRAME_OVERHEAD(r5)
-	lis	r6,MSR_VEC@h
-	andc	r4,r4,r6
-	std	r4,_MSR-STACK_FRAME_OVERHEAD(r5)
-1:
-#endif /* CONFIG_SMP */
-	/* Hack: if we get an altivec unavailable trap with VRSAVE
-	 * set to all zeros, we assume this is a broken application
-	 * that fails to set it properly, and thus we switch it to
-	 * all 1's
-	 */
-	mfspr	r4,SPRN_VRSAVE
-	cmpdi	0,r4,0
-	bne+	1f
-	li	r4,-1
-	mtspr	SPRN_VRSAVE,r4
-1:
-	/* enable use of VMX after return */
-	ld	r4,PACACURRENT(r13)
-	addi	r5,r4,THREAD		/* Get THREAD */
-	oris	r12,r12,MSR_VEC@h
-	std	r12,_MSR(r1)
-	li	r4,1
-	li	r10,THREAD_VSCR
-	stw	r4,THREAD_USED_VR(r5)
-	lvx	vr0,r10,r5
-	mtvscr	vr0
-	REST_32VRS(0,r4,r5)
-#ifndef CONFIG_SMP
-	/* Update last_task_used_math to 'current' */
-	subi	r4,r5,THREAD		/* Back to 'current' */
-	std	r4,0(r3)
-#endif /* CONFIG_SMP */
-	/* restore registers and return */
-	blr
-#endif /* CONFIG_ALTIVEC */
-
-#ifdef CONFIG_VSX
-/*
- * load_up_vsx(unused, unused, tsk)
- * Disable VSX for the task which had it previously,
- * and save its vector registers in its thread_struct.
- * Reuse the fp and vsx saves, but first check to see if they have
- * been saved already.
- * On entry: r13 == 'current' && last_task_used_vsx != 'current'
- */
-_STATIC(load_up_vsx)
-/* Load FP and VSX registers if they haven't been done yet */
-	andi.	r5,r12,MSR_FP
-	beql+	load_up_fpu		/* skip if already loaded */
-	andis.	r5,r12,MSR_VEC@h
-	beql+	load_up_altivec		/* skip if already loaded */
-
-#ifndef CONFIG_SMP
-	ld	r3,last_task_used_vsx@got(r2)
-	ld	r4,0(r3)
-	cmpdi	0,r4,0
-	beq	1f
-	/* Disable VSX for last_task_used_vsx */
-	addi	r4,r4,THREAD
-	ld	r5,PT_REGS(r4)
-	ld	r4,_MSR-STACK_FRAME_OVERHEAD(r5)
-	lis	r6,MSR_VSX@h
-	andc	r6,r4,r6
-	std	r6,_MSR-STACK_FRAME_OVERHEAD(r5)
-1:
-#endif /* CONFIG_SMP */
-	ld	r4,PACACURRENT(r13)
-	addi	r4,r4,THREAD		/* Get THREAD */
-	li	r6,1
-	stw	r6,THREAD_USED_VSR(r4) /* ... also set thread used vsr */
-	/* enable use of VSX after return */
-	oris	r12,r12,MSR_VSX@h
-	std	r12,_MSR(r1)
-#ifndef CONFIG_SMP
-	/* Update last_task_used_math to 'current' */
-	ld	r4,PACACURRENT(r13)
-	std	r4,0(r3)
-#endif /* CONFIG_SMP */
-	b	fast_exception_return
-#endif /* CONFIG_VSX */
-
-/*
- * Hash table stuff
- */
-	.align	7
-_STATIC(do_hash_page)
-	std	r3,_DAR(r1)
-	std	r4,_DSISR(r1)
-
-	andis.	r0,r4,0xa450		/* weird error? */
-	bne-	handle_page_fault	/* if not, try to insert a HPTE */
-BEGIN_FTR_SECTION
-	andis.	r0,r4,0x0020		/* Is it a segment table fault? */
-	bne-	do_ste_alloc		/* If so handle it */
-END_FTR_SECTION_IFCLR(CPU_FTR_SLB)
-
-	/*
-	 * On iSeries, we soft-disable interrupts here, then
-	 * hard-enable interrupts so that the hash_page code can spin on
-	 * the hash_table_lock without problems on a shared processor.
-	 */
-	DISABLE_INTS
-
-	/*
-	 * Currently, trace_hardirqs_off() will be called by DISABLE_INTS
-	 * and will clobber volatile registers when irq tracing is enabled
-	 * so we need to reload them. It may be possible to be smarter here
-	 * and move the irq tracing elsewhere but let's keep it simple for
-	 * now
-	 */
-#ifdef CONFIG_TRACE_IRQFLAGS
-	ld	r3,_DAR(r1)
-	ld	r4,_DSISR(r1)
-	ld	r5,_TRAP(r1)
-	ld	r12,_MSR(r1)
-	clrrdi	r5,r5,4
-#endif /* CONFIG_TRACE_IRQFLAGS */
-	/*
-	 * We need to set the _PAGE_USER bit if MSR_PR is set or if we are
-	 * accessing a userspace segment (even from the kernel). We assume
-	 * kernel addresses always have the high bit set.
-	 */
-	rlwinm	r4,r4,32-25+9,31-9,31-9	/* DSISR_STORE -> _PAGE_RW */
-	rotldi	r0,r3,15		/* Move high bit into MSR_PR posn */
-	orc	r0,r12,r0		/* MSR_PR | ~high_bit */
-	rlwimi	r4,r0,32-13,30,30	/* becomes _PAGE_USER access bit */
-	ori	r4,r4,1			/* add _PAGE_PRESENT */
-	rlwimi	r4,r5,22+2,31-2,31-2	/* Set _PAGE_EXEC if trap is 0x400 */
-
-	/*
-	 * r3 contains the faulting address
-	 * r4 contains the required access permissions
-	 * r5 contains the trap number
-	 *
-	 * at return r3 = 0 for success
-	 */
-	bl	.hash_page		/* build HPTE if possible */
-	cmpdi	r3,0			/* see if hash_page succeeded */
-
-BEGIN_FW_FTR_SECTION
-	/*
-	 * If we had interrupts soft-enabled at the point where the
-	 * DSI/ISI occurred, and an interrupt came in during hash_page,
-	 * handle it now.
-	 * We jump to ret_from_except_lite rather than fast_exception_return
-	 * because ret_from_except_lite will check for and handle pending
-	 * interrupts if necessary.
-	 */
-	beq	13f
-END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES)
-
-BEGIN_FW_FTR_SECTION
-	/*
-	 * Here we have interrupts hard-disabled, so it is sufficient
-	 * to restore paca->{soft,hard}_enable and get out.
-	 */
-	beq	fast_exc_return_irq	/* Return from exception on success */
-END_FW_FTR_SECTION_IFCLR(FW_FEATURE_ISERIES)
-
-	/* For a hash failure, we don't bother re-enabling interrupts */
-	ble-	12f
-
-	/*
-	 * hash_page couldn't handle it, set soft interrupt enable back
-	 * to what it was before the trap.  Note that .raw_local_irq_restore
-	 * handles any interrupts pending at this point.
-	 */
-	ld	r3,SOFTE(r1)
-	TRACE_AND_RESTORE_IRQ_PARTIAL(r3, 11f)
-	bl	.raw_local_irq_restore
-	b	11f
-
-/* Here we have a page fault that hash_page can't handle. */
-handle_page_fault:
-	ENABLE_INTS
-11:	ld	r4,_DAR(r1)
-	ld	r5,_DSISR(r1)
-	addi	r3,r1,STACK_FRAME_OVERHEAD
-	bl	.do_page_fault
-	cmpdi	r3,0
-	beq+	13f
-	bl	.save_nvgprs
-	mr	r5,r3
-	addi	r3,r1,STACK_FRAME_OVERHEAD
-	lwz	r4,_DAR(r1)
-	bl	.bad_page_fault
-	b	.ret_from_except
-
-13:	b	.ret_from_except_lite
-
-/* We have a page fault that hash_page could handle but HV refused
- * the PTE insertion
- */
-12:	bl	.save_nvgprs
-	mr	r5,r3
-	addi	r3,r1,STACK_FRAME_OVERHEAD
-	ld	r4,_DAR(r1)
-	bl	.low_hash_fault
-	b	.ret_from_except
-
-	/* here we have a segment miss */
-do_ste_alloc:
-	bl	.ste_allocate		/* try to insert stab entry */
-	cmpdi	r3,0
-	bne-	handle_page_fault
-	b	fast_exception_return
-
-/*
- * r13 points to the PACA, r9 contains the saved CR,
- * r11 and r12 contain the saved SRR0 and SRR1.
- * r9 - r13 are saved in paca->exslb.
- * We assume we aren't going to take any exceptions during this procedure.
- * We assume (DAR >> 60) == 0xc.
- */
-	.align	7
-_GLOBAL(do_stab_bolted)
-	stw	r9,PACA_EXSLB+EX_CCR(r13)	/* save CR in exc. frame */
-	std	r11,PACA_EXSLB+EX_SRR0(r13)	/* save SRR0 in exc. frame */
-
-	/* Hash to the primary group */
-	ld	r10,PACASTABVIRT(r13)
-	mfspr	r11,SPRN_DAR
-	srdi	r11,r11,28
-	rldimi	r10,r11,7,52	/* r10 = first ste of the group */
-
-	/* Calculate VSID */
-	/* This is a kernel address, so protovsid = ESID */
-	ASM_VSID_SCRAMBLE(r11, r9, 256M)
-	rldic	r9,r11,12,16	/* r9 = vsid << 12 */
-
-	/* Search the primary group for a free entry */
-1:	ld	r11,0(r10)	/* Test valid bit of the current ste	*/
-	andi.	r11,r11,0x80
-	beq	2f
-	addi	r10,r10,16
-	andi.	r11,r10,0x70
-	bne	1b
-
-	/* Stick for only searching the primary group for now.		*/
-	/* At least for now, we use a very simple random castout scheme */
-	/* Use the TB as a random number ;  OR in 1 to avoid entry 0	*/
-	mftb	r11
-	rldic	r11,r11,4,57	/* r11 = (r11 << 4) & 0x70 */
-	ori	r11,r11,0x10
-
-	/* r10 currently points to an ste one past the group of interest */
-	/* make it point to the randomly selected entry			*/
-	subi	r10,r10,128
-	or 	r10,r10,r11	/* r10 is the entry to invalidate	*/
-
-	isync			/* mark the entry invalid		*/
-	ld	r11,0(r10)
-	rldicl	r11,r11,56,1	/* clear the valid bit */
-	rotldi	r11,r11,8
-	std	r11,0(r10)
-	sync
-
-	clrrdi	r11,r11,28	/* Get the esid part of the ste		*/
-	slbie	r11
-
-2:	std	r9,8(r10)	/* Store the vsid part of the ste	*/
-	eieio
-
-	mfspr	r11,SPRN_DAR		/* Get the new esid			*/
-	clrrdi	r11,r11,28	/* Permits a full 32b of ESID		*/
-	ori	r11,r11,0x90	/* Turn on valid and kp			*/
-	std	r11,0(r10)	/* Put new entry back into the stab	*/
-
-	sync
-
-	/* All done -- return from exception. */
-	lwz	r9,PACA_EXSLB+EX_CCR(r13)	/* get saved CR */
-	ld	r11,PACA_EXSLB+EX_SRR0(r13)	/* get saved SRR0 */
-
-	andi.	r10,r12,MSR_RI
-	beq-	unrecov_slb
-
-	mtcrf	0x80,r9			/* restore CR */
-
-	mfmsr	r10
-	clrrdi	r10,r10,2
-	mtmsrd	r10,1
-
-	mtspr	SPRN_SRR0,r11
-	mtspr	SPRN_SRR1,r12
-	ld	r9,PACA_EXSLB+EX_R9(r13)
-	ld	r10,PACA_EXSLB+EX_R10(r13)
-	ld	r11,PACA_EXSLB+EX_R11(r13)
-	ld	r12,PACA_EXSLB+EX_R12(r13)
-	ld	r13,PACA_EXSLB+EX_R13(r13)
-	rfid
-	b	.	/* prevent speculative execution */
-
-/*
- * Space for CPU0's segment table.
- *
- * On iSeries, the hypervisor must fill in at least one entry before
- * we get control (with relocate on).  The address is given to the hv
- * as a page number (see xLparMap below), so this must be at a
- * fixed address (the linker can't compute (u64)&initial_stab >>
- * PAGE_SHIFT).
- */
-	. = STAB0_OFFSET	/* 0x6000 */
-	.globl initial_stab
-initial_stab:
-	.space	4096
-
-#ifdef CONFIG_PPC_PSERIES
-/*
- * Data area reserved for FWNMI option.
- * This address (0x7000) is fixed by the RPA.
- */
-	.= 0x7000
-	.globl fwnmi_data_area
-fwnmi_data_area:
-#endif /* CONFIG_PPC_PSERIES */
-
-	/* iSeries does not use the FWNMI stuff, so it is safe to put
-	 * this here, even if we later allow kernels that will boot on
-	 * both pSeries and iSeries */
-#ifdef CONFIG_PPC_ISERIES
-        . = LPARMAP_PHYS
-	.globl xLparMap
-xLparMap:
-	.quad	HvEsidsToMap		/* xNumberEsids */
-	.quad	HvRangesToMap		/* xNumberRanges */
-	.quad	STAB0_PAGE		/* xSegmentTableOffs */
-	.zero	40			/* xRsvd */
-	/* xEsids (HvEsidsToMap entries of 2 quads) */
-	.quad	PAGE_OFFSET_ESID	/* xKernelEsid */
-	.quad	PAGE_OFFSET_VSID	/* xKernelVsid */
-	.quad	VMALLOC_START_ESID	/* xKernelEsid */
-	.quad	VMALLOC_START_VSID	/* xKernelVsid */
-	/* xRanges (HvRangesToMap entries of 3 quads) */
-	.quad	HvPagesToMap		/* xPages */
-	.quad	0			/* xOffset */
-	.quad	PAGE_OFFSET_VSID << (SID_SHIFT - HW_PAGE_SHIFT)	/* xVPN */
-
-#endif /* CONFIG_PPC_ISERIES */
-
-#ifdef CONFIG_PPC_PSERIES
-        . = 0x8000
-#endif /* CONFIG_PPC_PSERIES */
 
 /*
  * On pSeries and most other platforms, secondary processors spin