blob: fb6f94873af222f5e4d25a4790bf647ff0c42e0a (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
|
/*
* U-boot - Configuration file for BF561 EZKIT board
*/
#ifndef __CONFIG_BF561_EZKIT_H__
#define __CONFIG_BF561_EZKIT_H__
#include <asm/config-pre.h>
/*
* Processor Settings
*/
#define CONFIG_BFIN_CPU bf561-0.3
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
/*
* Clock Settings
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
*/
/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ 30000000
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
/* 1 = CLKIN / 2 */
#define CONFIG_CLKIN_HALF 0
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
/* 1 = bypass PLL */
#define CONFIG_PLL_BYPASS 0
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
/* Values can range from 0-63 (where 0 means 64) */
#define CONFIG_VCO_MULT 20
/* CCLK_DIV controls the core clock divider */
/* Values can be 1, 2, 4, or 8 ONLY */
#define CONFIG_CCLK_DIV 1
/* SCLK_DIV controls the system clock divider */
/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 6
/*
* Memory Settings
*/
#define CONFIG_MEM_ADD_WDTH 9
#define CONFIG_MEM_SIZE 64
#define CONFIG_EBIU_SDRRC_VAL 0x306
#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
#define CONFIG_EBIU_AMGCTL_VAL 0x3F
#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
#define CONFIG_SYS_MALLOC_LEN (128 * 1024)
/*
* Network Settings
*/
#define ADI_CMDS_NETWORK 1
#define CONFIG_SMC91111 1
#define CONFIG_SMC91111_BASE 0x2C010300
#define CONFIG_SMC_USE_32_BIT 1
#define CONFIG_HOSTNAME bf561-ezkit
/* Uncomment next line to use fixed MAC address */
/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
/*
* Flash Settings
*/
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI_AMD_RESET
#define CONFIG_SYS_FLASH_BASE 0x20000000
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 135
/* The BF561-EZKIT uses a top boot flash */
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_OFFSET (0x800000 - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
#define CONFIG_ENV_SECT_SIZE 0x2000
/*
* I2C Settings
*/
#define CONFIG_SYS_I2C_SOFT
#ifdef CONFIG_SYS_I2C_SOFT
#define CONFIG_SYS_I2C
#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF0
#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF1
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
#define CONFIG_SYS_I2C_SOFT_SPEED 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE 0
#endif
/*
* Misc Settings
*/
#define CONFIG_UART_CONSOLE 0
/*
* Run core 1 from L1 SRAM start address when init uboot on core 0
*/
/* #define CONFIG_CORE1_RUN 1 */
/*
* Pull in common ADI header for remaining command/environment setup
*/
#include <configs/bfin_adi_common.h>
#endif
|
