1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
|
Motorola MPC8540ADS and MPC8560ADS board
Xianghua Xiao(X.Xiao@motorola.com)
Created 10/15/03
-----------------------------------------
1. SWITCH SETTINGS & JUMPERS
1.1 First, make sure the board default setting is consistent with the document
shipped with your board. Then apply the following changes:
SW3[1-6]="all OFF" (boot from 32bit flash, no boot sequence is used)
SW10[2-6]="all OFF" (turn on CPM SCC for serial port,works for 8540/8560)
SW11[2]='OFF for dracom, ON for draco' (single switch to toggle draco.dracom mode)
SW4[7-8]="OFF OFF" (enable serial ports,I'm using the top serial connector)
SW22[1-4]="OFF OFF ON OFF"
SW5[1-10[="ON ON OFF OFF OFF OFF OFF OFF OFF OFF"
J1 = "Enable Prog" (Make sure your flash is programmable for development)
Ethernet PHY connectors(J47,J56) should be removed if you want to use the ethernet.
1.2 If you want to test PCI functionality with a 33Mhz PCI card, you will have to change
the system clock from the default 66Mhz to 33Mhz by setting SW15[1]="OFF" and
SW17[8]="OFF". After that you may also need double your platform clock(SW6) because
the system clock is now only half of its original value.
1.3 SW6 is a very important switch, it decides your platform clock and CPU clock based on
the on-board system clock(default 66MHz). Check the document along with your board
for details.
2. MEMORY MAP TO WORK WITH LINUX KERNEL
2.1. For the initial bringup, we adopted a consistent memory scheme between u-boot and
linux kernel, you can customize it based on your system requirements:
DDR: 0x00000000-0x1fffffff (max 512MB)
PCI: 0xe0000000-0xefffffff (256MB)
RIO: 0xf0000000-0xf7ffffff (128MB)
Local SDRAM: 0xf8000000-0xfbffffff (64MB)
Local CSx: 0xfc000000-0xfdefffff (31MB) BCSR,RTC,ATM config,etc.
CCSRBAR: 0xfdf00000-0xfdffffff (1MB)
Flash: 0xfe000000-0xffffffff (max 32MB)
2.2 We are submitting Linux kernel patches for MPC8540 and MPC8560. Hope you will be
able to download them from linuxppc-2.4 public source by the time you are reading
this. Please make sure the kernel's ppcboot.h is consistent with U-Boot's u-boot.h,
then you can use two default configuration files in the kernel source as a test:
arch/ppc/configs/mpc8540ads_defconfig
arch/ppc/configs/mpc8560ads_defconfig
3. DEFINITIONS AND COMPILATION
3.1 Explanation on NEW definitions in include/configs/MPC8540ADS.h and include/
configs/MPC8560ADS.h
CONFIG_BOOKE BOOKE(e.g. Motorola MPC85xx, IBM 440, etc)
CONFIG_E500 BOOKE e500 family(Motorola)
CONFIG_MPC85xx MPC8540,MPC8560 and their derivatives
CONFIG_MPC85xx_REV1 MPC85xx Rev 1 Chip, in general you will use a Rev2
chip from Nov.2003. If you still see this definition
while you have a Rev2(and newer) chip,undef this.
CONFIG_MPC8540 MPC8540 specific
CONFIG_MPC8560 MPC8560 specific
CONFIG_MPC8540ADS MPC8540ADS board specific
CONFIG_MPC8560ADS MPC8560ADS board specific
CONFIG_TSEC_ENET Use on-chip 10/100/1000 ethernet for networking
CONFIG_SPD_EEPROM Use SPD EEPROM for DDR auto configuration, you can also
manual config the DDR after undef this definition.
CONFIG_DDR_ECC only for ECC DDR module
CONFIG_DDR_DLL possible DLL fix needed for Rev1 chip for more stability.
you can disable this if you're having a newer chip.
CONFIG_RAM_AS_FLASH after define this, you can load U-Boot into localbus
SDRAM and treat localbus SDRAM as a flash. We use this
memory based U-Boot before flash is working while Metrowerks
and Windriver are still working on their flash/JTAG tools.
if you can program the flash directly, undef this.
Other than the above definitions, the rest in the config files are straightforward.
3.2 Compilation
export CROSS_COMPILE=your-cross-compile-prefix(assuming you're using BASH shell)
cd u-boot
make distclean
make MPC8560ADS_config (or make MPC8540ADS_config)
make
4. Note on the 10/100/1000 Ethernet controller:
4.1 Sometimes after U-Boot is up, the 'tftp' won't work well with TSEC ethernet. If that
happens, you can try the following steps to make network work:
MPC8560ADS>tftp 1000000 pImage
(if it hangs, use Ctrl-C to quit)
MPC8560ADS>nm fdf24524
>0
>1
>. (to quit this memory operation)
MPC8560ADS>tftp 1000000 pImage
5. Screen dump:
5.1 MPC8540ADS board
U-Boot 1.0.0-pre (Oct 15 2003 - 13:40:33)
Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200010
Board: Motorola MPC8540ADS Board
CPU: 792 MHz
CCB: 264 MHz
DDR: 132 MHz
LBC: 66 MHz
L1 D-cache 32KB, L1 I-cache 32KB enabled.
I2C: ready
DRAM: DDR module detected, total size:128MB.
128 MB
FLASH: 16 MB
L2 cache enabled: 256KB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: MOTOROLA ETHERNE
Hit any key to stop autoboot: 0
MPC8540ADS=> fli
Bank # 1: Intel 28F640J3A (64 Mbit, 64 x 128K)
Size: 16 MB in 64 Sectors
Sector Start Addresses:
FF000000 FF040000 FF080000 FF0C0000 FF100000
FF140000 FF180000 FF1C0000 FF200000 FF240000
FF280000 FF2C0000 FF300000 FF340000 FF380000
FF3C0000 FF400000 FF440000 FF480000 FF4C0000
FF500000 FF540000 FF580000 FF5C0000 FF600000
FF640000 FF680000 FF6C0000 FF700000 FF740000
FF780000 FF7C0000 FF800000 FF840000 FF880000
FF8C0000 FF900000 FF940000 FF980000 FF9C0000
FFA00000 FFA40000 FFA80000 FFAC0000 FFB00000
FFB40000 FFB80000 FFBC0000 FFC00000 FFC40000
FFC80000 FFCC0000 FFD00000 FFD40000 FFD80000
FFDC0000 FFE00000 FFE40000 FFE80000 FFEC0000
FFF00000 FFF40000 FFF80000 (RO) FFFC0000 (RO)
MPC8540ADS=> imi ff000000
## Checking Image at ff000000 ...
Image Name: Linux-2.4.21-rc5
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 800594 Bytes = 781.8 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
MPC8540ADS=> bdinfo
memstart = 0x00000000
memsize = 0x08000000
flashstart = 0xFF000000
flashsize = 0x01000000
flashoffset = 0x00000000
sramstart = 0x00000000
sramsize = 0x00000000
immr_base = 0xFDF00000
bootflags = 0x40003F80
intfreq = 792 MHz
busfreq = 264 MHz
ethaddr = 00:01:AF:07:9B:8A
eth1addr = 00:01:AF:07:9B:8B
eth2addr = 00:01:AF:07:9B:8C
IP addr = 10.82.0.105
baudrate = 115200 bps
MPC8540ADS=> printenv
bootargs=root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200
bootcmd=bootm 0xff300000 0xff700000
bootdelay=3
baudrate=115200
loads_echo=1
ethaddr=00:01:af:07:9b:8a
eth1addr=00:01:af:07:9b:8b
eth2addr=00:01:af:07:9b:8c
ipaddr=10.82.0.105
serverip=163.12.64.52
rootpath=/home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
gatewayip=10.82.1.254
netmask=255.255.254.0
hostname=MPC8560ADS_PILOT_003
bootfile=pImage
stdin=serial
stdout=serial
stderr=serial
Environment size: 560/8188 bytes
MPC8540ADS=> bootm ff000000
## Booting image at ff000000 ...
Image Name: Linux-2.4.21-rc5
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 800594 Bytes = 781.8 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
mpc85xx_init(): exit
id mach(): done
MMU:enter
Memory CAM mapping: CAM0=64Mb, CAM1=64Mb, CAM2=0Mb residual: 0Mb
MMU:hw init
MMU:mapin
MMU:mapin_ram done
MMU:setio
MMU:exit
Linux version 2.4.21-rc5 (@etest) (gcc version 2.95.3 20010315 (release)) #1 Wed Oct 15 09:05:42 CDT 2003
setup_arch: enter
setup_arch: bootmem
mpc85xx_setup_arch
Host Bridge Vendor ID = 1057
Host Bridge Device ID = 3
Host Bridge header = 0
arch: exit
On node 0 totalpages: 32768
zone(0): 32768 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200
openpic: enter
OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fdf40000
openpic: timer
openpic: external
openpic: spurious
openpic: exit
time_init: decrementer frequency = 33.000000 MHz
Calibrating delay loop... 226.09 BogoMIPS
Memory: 127488k available (1344k kernel code, 448k data, 248k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xfdf04500 (irq = 90) is a 16550A
ttyS01 at 0xfdf04600 (irq = 0) is a 16550A
eth0: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8a:
eth1: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8b:
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 5.0.43-k1
Copyright (c) 1999-2003 Intel Corporation.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
IP-Config: Complete:
device=eth0, addr=10.82.0.105, mask=255.255.254.0, gw=10.82.1.254,
host=mpc8540ads-003, domain=, nis-domain=(none),
bootserver=163.12.64.52, rootserver=163.12.64.52, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Looking up port of RPC 100003/2 on 163.12.64.52
Looking up port of RPC 100005/1 on 163.12.64.52
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 248k init
INIT: version 2.78 booting
Activating swap...
Checking all file systems...
Parallelizing fsck version 1.22 (22-Jun-2001)
Mounting local filesystems...
nothing was mounted
Cleaning: /etc/network/ifstate.
Setting up IP spoofing protection: rp_filter.
Disable TCP/IP Explicit Congestion Notification: done.
Configuring network interfaces: done.
Starting portmap daemon: portmap.
Cleaning: /tmp /var/lock /var/run.
INIT: Entering runlevel: 2
Starting system log daemon: syslogd klogd.
Starting internet superserver: inetd.
mpc8540ads-003 login: root
Last login: Thu Jan 1 00:00:07 1970 on console
Linux mpc8540ads-003 2.4.21-rc5 #1 Wed Oct 15 09:05:42 CDT 2003 ppc unknown
root@mpc8540ads-003:~# ls
21142.o aa e100.o hello.o mii.o timer.o
root@mpc8540ads-003:~# /sbin/ifconfig
eth0 Link encap:Ethernet HWaddr 00:01:AF:07:9B:8A
inet addr:10.82.0.105 Bcast:10.82.1.255 Mask:255.255.254.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4576 errors:0 dropped:0 overruns:0 frame:0
TX packets:2587 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:4457023 (4.2 Mb) TX bytes:437770 (427.5 Kb)
Base address:0x4000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:296 (296.0 b) TX bytes:296 (296.0 b)
root@mpc8540ads-003:~# ping 163.12.64.52
PING 163.12.64.52 (163.12.64.52): 56 data bytes
64 bytes from 163.12.64.52: icmp_seq=0 ttl=63 time=0.2 ms
64 bytes from 163.12.64.52: icmp_seq=1 ttl=63 time=0.1 ms
64 bytes from 163.12.64.52: icmp_seq=2 ttl=63 time=0.1 ms
--- 163.12.64.52 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 0.1/0.1/0.2 ms
root@mpc8540ads-003:~#
5.2 MPC8560ADS board
U-Boot 1.0.0-pre (Oct 15 2003 - 13:42:04)
Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200010
Board: Motorola MPC8560ADS Board
CPU: 792 MHz
CCB: 264 MHz
DDR: 132 MHz
LBC: 66 MHz
CPM: 264 Mhz
L1 D-cache 32KB, L1 I-cache 32KB enabled.
I2C: ready
DRAM: DDR module detected, total size:128MB.
128 MB
FLASH: 16 MB
L2 cache enabled: 256KB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: MOTOROLA ETHERNE
Hit any key to stop autoboot: 3
MPC8560ADS=> bdinfo
memstart = 0x00000000
memsize = 0x08000000
flashstart = 0xFF000000
flashsize = 0x01000000
flashoffset = 0x00000000
sramstart = 0x00000000
sramsize = 0x00000000
immr_base = 0xFDF00000
bootflags = 0x00000000
vco = 528 MHz
sccfreq = 132 MHz
brgfreq = 132 MHz
intfreq = 792 MHz
cpmfreq = 264 MHz
busfreq = 264 MHz
ethaddr = 00:01:AF:07:9B:8A
eth1addr = 00:01:AF:07:9B:8B
eth2addr = 00:01:AF:07:9B:8C
IP addr = 10.82.0.105
baudrate = 115200 bps
MPC8560ADS=> printenv
bootargs=root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8560ads-003:eth0:off console=ttyS0,115200
bootcmd=bootm 0xff400000 0xff700000
bootdelay=3
baudrate=115200
loads_echo=1
ethaddr=00:01:af:07:9b:8a
eth1addr=00:01:af:07:9b:8b
eth2addr=00:01:af:07:9b:8c
ipaddr=10.82.0.105
serverip=163.12.64.52
rootpath=/home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
gatewayip=10.82.1.254
netmask=255.255.254.0
hostname=MPC8560ADS_PILOT_003
bootfile=pImage
stdin=serial
stdout=serial
stderr=serial
Environment size: 560/8188 bytes
MPC8560ADS=> fli
Bank # 1: Intel 28F640J3A (64 Mbit, 64 x 128K)
Size: 16 MB in 64 Sectors
Sector Start Addresses:
FF000000 FF040000 FF080000 FF0C0000 FF100000
FF140000 FF180000 FF1C0000 FF200000 FF240000
FF280000 FF2C0000 FF300000 FF340000 FF380000
FF3C0000 FF400000 FF440000 FF480000 FF4C0000
FF500000 FF540000 FF580000 FF5C0000 FF600000
FF640000 FF680000 FF6C0000 FF700000 FF740000
FF780000 FF7C0000 FF800000 FF840000 FF880000
FF8C0000 FF900000 FF940000 FF980000 FF9C0000
FFA00000 FFA40000 FFA80000 FFAC0000 FFB00000
FFB40000 FFB80000 FFBC0000 FFC00000 FFC40000
FFC80000 FFCC0000 FFD00000 FFD40000 FFD80000
FFDC0000 FFE00000 FFE40000 FFE80000 FFEC0000
FFF00000 FFF40000 FFF80000 (RO) FFFC0000 (RO)
MPC8560ADS=> imi ff100000
## Checking Image at ff100000 ...
Image Name: Linux-2.4.21-rc5
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 755361 Bytes = 737.7 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
MPC8560ADS=> tftp 1000000 pImage.dracom.public
TFTP from server 163.12.64.52; our IP address is 10.82.0.105; sending through gateway 10.82.1.254
Filename 'pImage.dracom.public'.
Load address: 0x1000000
Loading: *#################################################################
#################################################################
##################
done
Bytes transferred = 755425 (b86e1 hex)
MPC8560ADS=> bootm ff100000
## Booting image at ff100000 ...
Image Name: Linux-2.4.21-rc5
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 755361 Bytes = 737.7 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
mpc85xx_init(): exit
id mach(): done
MMU:enter
Memory CAM mapping: CAM0=64Mb, CAM1=64Mb, CAM2=0Mb residual: 0Mb
MMU:hw init
MMU:mapin
MMU:mapin_ram done
MMU:setio
MMU:exit
Linux version 2.4.21-rc5 (@etest) (gcc version 2.95.3 20010315 (release)) #2 Wed Oct 15 09:13:46 CDT 2003
setup_arch: enter
setup_arch: bootmem
mpc85xx_setup_arch
Host Bridge Vendor ID = 1057
Host Bridge Device ID = 3
Host Bridge header = 0
arch: exit
On node 0 totalpages: 32768
zone(0): 32768 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8560ads-003:eth0:off console=ttyS0,115200
openpic: enter
OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fdf40000
openpic: timer
openpic: external
openpic: spurious
openpic: exit
time_init: decrementer frequency = 33.000000 MHz
Calibrating delay loop... 226.09 BogoMIPS
Memory: 127624k available (1276k kernel code, 384k data, 236k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
CPM UART driver version 0.01
ttyS0 on SCC1 at 0x8000, BRG1
UART interrupt installed(40)
pty: 256 Unix98 ptys configured
eth0: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8a:
eth1: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8b:
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 5.0.43-k1
Copyright (c) 1999-2003 Intel Corporation.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
IP-Config: Complete:
device=eth0, addr=10.82.0.105, mask=255.255.254.0, gw=10.82.1.254,
host=mpc8560ads-003, domain=, nis-domain=(none),
bootserver=163.12.64.52, rootserver=163.12.64.52, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Looking up port of RPC 100003/2 on 163.12.64.52
Looking up port of RPC 100005/1 on 163.12.64.52
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 236k init
INIT: version 2.78 booting
Activating swap...
Checking all file systems...
Parallelizing fsck version 1.22 (22-Jun-2001)
Mounting local filesystems...
nothing was mounted
Cleaning: /etc/network/ifstate.
Setting up IP spoofing protection: FAILED
Configuring network interfaces: done.
Starting portmap daemon: portmap.
Cleaning: /tmp /var/lock /var/run.
INIT: Entering runlevel: 2
Starting system log daemon: syslogd klogd.
Starting internet superserver: inetd.
mpc8560ads-003 login: root
Last login: Thu Jan 1 00:00:05 1970 on console
Linux mpc8560ads-003 2.4.21-rc5 #2 Wed Oct 15 09:13:46 CDT 2003 ppc unknown
root@mpc8560ads-003:~# ls
21142.o aa e100.o hello.o mii.o timer.o
root@mpc8560ads-003:~# cd /
root@mpc8560ads-003:/# ls
bin boot dev etc home lib mnt opt proc root sbin tmp usr var
root@mpc8560ads-003:/# /sbin/ifconfig
eth0 Link encap:Ethernet HWaddr 00:01:AF:07:9B:8A
inet addr:10.82.0.105 Bcast:10.82.1.255 Mask:255.255.254.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4608 errors:0 dropped:0 overruns:0 frame:0
TX packets:2610 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:4465943 (4.2 Mb) TX bytes:440944 (430.6 Kb)
Base address:0x4000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:296 (296.0 b) TX bytes:296 (296.0 b)
root@mpc8560ads-003:/# ping 163.12.64.52
PING 163.12.64.52 (163.12.64.52): 56 data bytes
64 bytes from 163.12.64.52: icmp_seq=0 ttl=63 time=0.1 ms
64 bytes from 163.12.64.52: icmp_seq=1 ttl=63 time=0.1 ms
64 bytes from 163.12.64.52: icmp_seq=2 ttl=63 time=0.1 ms
--- 163.12.64.52 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 0.1/0.1/0.1 ms
root@mpc8560ads-003:/#
|
