1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
|
/*
* Copyright 2018-2019 NXP
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <command.h>
#include <cpu_func.h>
#include <hang.h>
#include <image.h>
#include <init.h>
#include <log.h>
#include <spl.h>
#include <asm/io.h>
#include <errno.h>
#include <asm/io.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/arch/imx8mp_pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-imx/boot_mode.h>
#include <power/pmic.h>
#include <power/pca9450.h>
#include <asm/arch/clock.h>
#include <asm/mach-imx/gpio.h>
#include <asm/mach-imx/mxc_i2c.h>
#include <fsl_esdhc.h>
#include <mmc.h>
#include <asm/arch/ddr.h>
DECLARE_GLOBAL_DATA_PTR;
int spl_board_boot_device(enum boot_device boot_dev_spl)
{
return BOOT_DEVICE_BOOTROM;
}
void spl_dram_init(void)
{
ddr_init(&dram_timing);
}
void spl_board_init(void)
{
puts("Normal Boot\n");
}
#define I2C_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PE)
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
struct i2c_pads_info i2c_pad_info1 = {
.scl = {
.i2c_mode = MX8MP_PAD_I2C1_SCL__I2C1_SCL | PC,
.gpio_mode = MX8MP_PAD_I2C1_SCL__GPIO5_IO14 | PC,
.gp = IMX_GPIO_NR(5, 14),
},
.sda = {
.i2c_mode = MX8MP_PAD_I2C1_SDA__I2C1_SDA | PC,
.gpio_mode = MX8MP_PAD_I2C1_SDA__GPIO5_IO15 | PC,
.gp = IMX_GPIO_NR(5, 15),
},
};
#ifdef CONFIG_POWER
#define I2C_PMIC 0
int power_init_board(void)
{
struct pmic *p;
int ret;
ret = power_pca9450_init(I2C_PMIC);
if (ret)
printf("power init failed");
p = pmic_get("PCA9450");
pmic_probe(p);
/* BUCKxOUT_DVS0/1 control BUCK123 output */
pmic_reg_write(p, PCA9450_BUCK123_DVS, 0x29);
/*
* increase VDD_SOC to typical value 0.95V before first
* DRAM access, set DVS1 to 0.85v for suspend.
* Enable DVS control through PMIC_STBY_REQ and
* set B1_ENMODE=1 (ON by PMIC_ON_REQ=H)
*/
pmic_reg_write(p, PCA9450_BUCK1OUT_DVS0, 0x1C);
pmic_reg_write(p, PCA9450_BUCK1OUT_DVS1, 0x14);
pmic_reg_write(p, PCA9450_BUCK1CTRL, 0x59);
/* set WDOG_B_CFG to cold reset */
pmic_reg_write(p, PCA9450_RESET_CTRL, 0xA1);
return 0;
}
#endif
#ifdef CONFIG_SPL_LOAD_FIT
int board_fit_config_name_match(const char *name)
{
/* Just empty function now - can't decide what to choose */
debug("%s: %s\n", __func__, name);
return 0;
}
#endif
/* Do not use BSS area in this phase */
void board_init_f(ulong dummy)
{
int ret;
arch_cpu_init();
init_uart_clk(1);
board_early_init_f();
ret = spl_early_init();
if (ret) {
debug("spl_init() failed: %d\n", ret);
hang();
}
preloader_console_init();
enable_tzc380();
setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
power_init_board();
/* DDR initialization */
spl_dram_init();
}
|
