summaryrefslogtreecommitdiffstats
path: root/drivers/usb/dwc3/Kconfig
Commit message (Collapse)AuthorAgeFilesLines
* usb: dwc3: add Amlogic GXL & GXL DWC3 GlueNeil Armstrong2020-10-051-0/+8
| | | | | | | | | | | | | | The USB support was initialy done with a set of PHYs and dwc3-of-simple because the architecture of the USB complex was not understood correctly at the time (and proper documentation was missing...). But with the G12A family, the USB complex was correctly understood and implemented correctly. This adds a proper driver for the glue, based on the G12A one, but with enough changes to require a different driver in U-Boot. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
* usb: dwc3: Kconfig: get rid of obsolete mode selectionJean-Jacques Hiblot2019-10-241-16/+2
| | | | | | | | | | | | | | The mode selection for the DWC3 is kind of obsolete. The driver does not have to be host only or gadget only. This choice is confusing. All the remaining callers of dwc3_uboot_init() explicitly set dr_mode before calling the function, so none rely on a default behavior. Remove the choice menu and keep only the USB_DWC3_GADGET option. Enable it by default if USB_GADGET and USB_DWC3 are enabled. It must be disabled for the evb-rk3328 as it uses DWC2 for the gadget and DWC3 for the host. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
* usb: dwc3: Add Meson G12A USB GlueNeil Armstrong2019-05-091-0/+8
| | | | | | | | | | | | | | | | | | | | | Adds support for Amlogic G12A USB Control Glue HW. The Amlogic G12A SoC Family embeds 2 USB Controllers : - a DWC3 IP configured as Host for USB2 and USB3 - a DWC2 IP configured as Peripheral USB2 Only A glue connects these both controllers to 2 USB2 PHYs, and optionnally to an USB3+PCIE Combo PHY shared with the PCIE controller. The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY. This driver sets the OTG capable port as Host mode by default, the switch to Device mode is to be done in a separate patch. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Marek Vasut <marex@denx.de>
* dwc3-generic: Handle the PHYs, the clocks and the reset linesJean-Jacques Hiblot2018-12-071-3/+4
| | | | | | | | This make the driver more generic. At this point this driver can replace the dwc3-of-simple implementation. Make the description in the Kconfig more generic too. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
* usb: dwc3: Add generic DWC3 glue logic driverMichal Simek2018-05-181-0/+6
| | | | | | | | | By enabling BLK by default this is the next driver which needs to get support for DM_USB. Adding generic DWC3 glue logic which only parse nodes and read device mode. Based on it probe proper host/peripheral DWC3 drivers for it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* usb: dwc3: add UniPhier specific glue layerMasahiro Yamada2017-10-011-0/+7
| | | | | | | | Add UniPhier platform specific glue layer to support USB3 Host mode on Synopsys DWC3 IP. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
* usb: dwc3: fix Kconfig dependency to accept host driver in drivers/usb/dwc3Masahiro Yamada2017-08-281-2/+2
| | | | | | | | | | | We see the choice of USB_DWC3_HOST / _GADGET in drivers/usb/dwc3/Kconfig, but we can not choose USB_DWC3_HOST unless USB_GADGET is defined. This is strange. Loosen the "depends on" and also move "select USB_GADGET_DUALSPEED" to the correct place. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* usb: dwc3: Move CONFIG_USB_DWC3_PHY_* to KconfigSam Protsenko2016-04-201-0/+17
| | | | Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
* usb: dwc3: Move CONFIG_USB_DWC3_OMAP to KconfigSam Protsenko2016-04-201-0/+10
| | | | Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
* usb: dwc3: Move CONFIG_USB_DWC3_GADGET/HOST to KconfigSam Protsenko2016-04-201-0/+23
| | | | | | Description was borrowed from kernel dwc3 Kconfig. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
* usb: gadget: Move CONFIG_USB_GADGET_DUALSPEED to KconfigSam Protsenko2016-04-201-0/+7
| | | | | | | | | | | | | | | | | | | | | | Move CONFIG_USB_GADGET_DUALSPEED option to Kconfig and make all UDC controllers select USB_GADGET_DUALSPEED: - add next options to Kconfig selecting USB_GADGET_DUALSPEED: - USB_GADGET_ATMEL_USBA - USB_GADGET_DWC2_OTG - USB_DWC3 - CI_UDC - make USB_MUSB_GADGET select USB_GADGET_DUALSPEED While at it, make some related fixes: - remove DUALSPEED from configs that don't enable gadget support: - kwb.h - tseries.h - add missing USB_GADGET option to next configs: - novena_defconfig - pcm051_rev*_defconfig - xfi3_defconfig Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
* usb: dwc3: remove un-used files from dwc3 folderKishon Vijay Abraham I2015-04-141-120/+0
| | | | | | | | removed un-used/un-supported files from dwc3. These files can be added later as and when the support is added. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
* usb: dwc3: add dwc3 folder from linux kernel to u-bootKishon Vijay Abraham I2015-04-141-0/+120
Added dwc3 folder from linux kernel 3.19-rc1 (97bf6af1f9) to u-boot. This will be adapted to work with u-boot in the following patches. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
generated by cgit (git 2.34.1) at 2026-01-07 08:54:41 +0000