summaryrefslogtreecommitdiffstats
path: root/board/freescale/imx8mn_evk
Commit message (Collapse)AuthorAgeFilesLines
* imx8mn-ddr4-evk: switch to use binmanPeng Fan2021-04-081-0/+10
| | | | | | Use binman to pack images Signed-off-by: Peng Fan <peng.fan@nxp.com>
* imx8mn: evk: update MAINTAINERSPeng2021-04-081-1/+2
| | | | | | | Add imx8mn_evk_defconfig to be maintained Typo fix Signed-off-by: Peng <peng.fan@nxp.com>
* imx8m: ddr: Disable CA VREF Training for LPDDR4Ye Li2021-04-081-1/+0
| | | | | | | | | | | | | | | | Users reported LPDDR4 MR12 value is set to 0 during PHY training, not the value from FSP timing structure, which cause compliance test failed. The root cause is the CATrainOpt[0] is set to 1 in 2D FSP timing but not set in 1D. According to PHY training application node, to enable the feature both 1D and 2D need set this field to 1, otherwise the training result will be incorrect. The PHY training doc also recommends to set CATrainOpt[0] to 0 to use MR12 value from message block (FSP structure). So update the LPDDR4 scripts of all mscale to clear CATrainOpt[0]. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Jacky Bai <ping.bai@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
* imx8mn: Add low drive mode support for DDR4/LPDDR4 EVKYe Li2021-04-085-1/+2513
| | | | | | | | | Add dedicated defconfigs for iMX8MN low drive mode which set the VDD_SOC and VDD_DRAM to 0.8v, DDR at 1600MTS (800Mhz clock) and GPU at 200Mhz. Signed-off-by: Ye Li <ye.li@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
* imx8mn: Add LPDDR4 EVK board supportPeng Fan2021-04-084-1/+1632
| | | | | | | | Add support for iMX8MN LPDDR4 EVK board which uses 2GB LPDDR4 and PCA9450B PMIC. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
* imx8mn_evk: drop duplicated codePeng Fan2021-04-081-2/+0
| | | | | | uart clk has been enabled, no need enable again. Signed-off-by: Peng Fan <peng.fan@nxp.com>
* imx8mn: Update the DDR4 timing script on imx8mn ddr4 evkJacky Bai2021-04-081-608/+449
| | | | | | | | | On i.MX8MN, we can only support DLL-ON mode only, so update the timing to support 2400mts & 1066mts setpoint. Signed-off-by: Jacky Bai <ping.bai@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
* common: Drop asm/global_data.h from common headerSimon Glass2021-02-022-0/+2
| | | | | | | | | | | | Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
* imx: imx8mn_ddr4_evk: Use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK boardPeng Fan2021-01-231-1/+1
| | | | | | | use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK board, we will use CONFIG_TARGET_IMX8MN_EVK for LPDDR4 EVK board. Signed-off-by: Peng Fan <peng.fan@nxp.com>
* doc: board: Convert i.MX8MN EVK README to reSTPeng Fan2020-11-011-37/+0
| | | | | | | Convert plain text documentation to reStructuredText format and add it to Sphinx TOC tree. No essential content change. Signed-off-by: Peng Fan <peng.fan@nxp.com>
* board: imx: address dd usage in READMEPeng Fan2020-11-011-1/+1
| | | | | | | | | | | | | | When using cygwin64 "dd (coreutils) 8.26 Packaged by Cygwin (8.26-2)", the last not 512bytes aligned data wat cut off and not burned into SD card. Saying the flash.bin size is 1085608 bytes, not 512bytes aligned. It only burned 1085440 bytes, the leaving 168 bytes were not burnned and cause boot issue. So update README dd command to add "conv=notrunc" Signed-off-by: Peng Fan <peng.fan@nxp.com>
* imx8m: Refactor the OPTEE memory removalPeng Fan2020-07-141-7/+0
| | | | | | | | | | | | | | | Current codes assume the OPTEE address is at the end of first DRAM bank. Adjust the process to allow OPTEE in the middle of first bank. When OPTEE memory is removed from first bank, it may split the first bank to two banks, adjust the MMU table for the split case, Since the default CONFIG_NR_DRAM_BANKS is 4, it is enough, just enlarge i.MX8MP evk to default to avoid issue. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com> Tested-by: Silvano di Ninno <silvano.dininno@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
* common: Drop log.h from common headerSimon Glass2020-05-181-0/+1
| | | | | | Move this header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
* command: Remove the cmd_tbl_t typedefSimon Glass2020-05-182-0/+2
| | | | | | | | | | | | | We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass <sjg@chromium.org>
* common: Drop init.h from common headerSimon Glass2020-05-182-0/+2
| | | | | | Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
* common: Drop image.h from common headerSimon Glass2020-05-181-0/+1
| | | | | | Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
* imx: imx8m*: Remove do_reset from board filesClaudius Heine2020-05-011-9/+0
| | | | | | | | | | | | | | | | | Use the `do_reset` implementation of `arch/arm/lib/reset.c` in SPL instead. It is very close to what is done here, anyway, and plays more nicely with the rest of U-Boot than adding a custom `do_reset` implementation into board files. `do_reset` from `arch/arm/lib/reset.c` calls `reset_cpu` with 0 as the addr parameter while the boards are passing WDOG1_BASE_ADDR. This is ok because the `reset_cpu` implementation uses WDOG1_BASE_ADDR by default if 0 is passed in. Co-Authored-by: Harald Seiler <hws@denx.de> Signed-off-by: Claudius Heine <ch@denx.de> Signed-off-by: Harald Seiler <hws@denx.de> Reviewed-by: Marek Vasut <marex@denx.de>
* common: Move hang() to the same header as panic()Simon Glass2020-01-171-0/+1
| | | | | | | | | | At present panic() is in the vsprintf.h header file. That does not seem like an obvious choice for hang(), even though it relates to panic(). So let's put hang() in its own header. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Migrate a few more files] Signed-off-by: Tom Rini <trini@konsulko.com>
* common: Move reset_cpu() to the CPU headerSimon Glass2020-01-171-0/+1
| | | | | | Move this function out of common.h and into a relevant header file. Signed-off-by: Simon Glass <sjg@chromium.org>
* imx: imx8mn_evk: add board_mmc_get_env_devPeng Fan2020-01-081-0/+5
| | | | | | | | | | Add board_mmc_get_env_dev, otherwise, Loading Environment from MMC... MMC Device 0 not found *** Warning - No MMC card found, using default environment Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
* imx8mn: evk: add READMEPeng Fan2020-01-081-0/+37
| | | | | | | Add a README for users to build a workable image. Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
* imx: add i.MX8MN DDR4 board supportPeng Fan2019-11-056-0/+1398
Support pinctrl/clk/sdhc, include ddr4 timing data. Log: U-Boot SPL 2019.10-rc3-00356-g497c500423-dirty (Sep 16 2019 - 10:54:58 +0800) Normal Boot Trying to boot from BOOTROM image offset 0x8000, pagesize 0x200, ivt offset 0x0 U-Boot 2019.10-rc3-00356-g497c500423-dirty (Sep 16 2019 - 10:54:58 +0800) CPU: Freescale i.MX8MNano rev1.0 at 24 MHz Reset cause: POR Model: NXP i.MX8MNano DDR4 EVK board DRAM: 2 GiB MMC: FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com>
generated by cgit (git 2.34.1) at 2025-09-03 00:56:08 +0000