diff options
Diffstat (limited to 'include/configs/wepep250.h')
| -rw-r--r-- | include/configs/wepep250.h | 199 |
1 files changed, 0 insertions, 199 deletions
diff --git a/include/configs/wepep250.h b/include/configs/wepep250.h deleted file mode 100644 index a961a27922..0000000000 --- a/include/configs/wepep250.h +++ /dev/null @@ -1,199 +0,0 @@ -/* - * Copyright (C) 2003 ETC s.r.o. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - * - * Written by Peter Figuli <peposh@etc.sk>, 2003. - * - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_PXA250 1 /* this is an PXA250 CPU */ -#define CONFIG_WEPEP250 1 /* config for wepep250 board */ -#undef CONFIG_USE_IRQ /* don't need use IRQ/FIQ */ - -/* we will never enable dcache, because we have to setup MMU first */ -#define CONFIG_SYS_NO_DCACHE - -/* - * Select serial console configuration - */ -#define CONFIG_PXA_SERIAL -#define CONFIG_BTUART 1 /* BTUART is default on WEP dev board */ -#define CONFIG_BAUDRATE 115200 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#undef CONFIG_CMD_CONSOLE -#undef CONFIG_CMD_LOADS -#undef CONFIG_CMD_NET -#undef CONFIG_CMD_SOURCE - - -/* - * Boot options. Setting delay to -1 stops autostart count down. - * NOTE: Sending parameters to kernel depends on kernel version and - * 2.4.19-rmk6-pxa1 patch used while my u-boot coding didn't accept - * parameters at all! Do not get confused by them so. - */ -#define CONFIG_BOOTDELAY -1 -#define CONFIG_BOOTARGS "root=/dev/mtdblock2 mem=32m console=ttyS01,115200n8" -#define CONFIG_BOOTCOMMAND "bootm 40000" - - -/* - * General options for u-boot. Modify to save memory foot print - */ -#define CONFIG_SYS_LONGHELP /* undef saves memory */ -#define CONFIG_SYS_PROMPT "WEP> " /* prompt string */ -#define CONFIG_SYS_CBSIZE 256 /* console I/O buffer */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* print buffer size */ -#define CONFIG_SYS_MAXARGS 16 /* max command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* boot args buf size */ - -#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest test area */ -#define CONFIG_SYS_MEMTEST_END 0xa0800000 - -#define CONFIG_SYS_HZ 1000 -#define CONFIG_SYS_CPUSPEED 0x141 /* core clock - register value */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -/* - * Definitions related to passing arguments to kernel. - */ -#define CONFIG_CMDLINE_TAG 1 /* send commandline to Kernel */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* send memory definition to kernel */ -#undef CONFIG_INITRD_TAG /* do not send initrd params */ -#undef CONFIG_VFD /* do not send framebuffer setup */ - - -/* - * Malloc pool need to host env + 128 Kb reserve for other allocations. - */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128<<10) ) -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ - -#define CONFIG_STACKSIZE (120<<10) /* stack size */ - -#ifdef CONFIG_USE_IRQ -#define CONFIG_STACKSIZE_IRQ (4<<10) /* IRQ stack */ -#define CONFIG_STACKSIZE_FIQ (4<<10) /* FIQ stack */ -#endif - -/* - * SDRAM Memory Map - */ -#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of SDRAM */ -#define WEP_SDRAM_1 0xa0000000 /* SDRAM bank #1 */ -#define WEP_SDRAM_1_SIZE 0x02000000 /* 32 MB ( 2 chip ) */ -#define WEP_SDRAM_2 0xa2000000 /* SDRAM bank #2 */ -#define WEP_SDRAM_2_SIZE 0x00000000 /* 0 MB */ -#define WEP_SDRAM_3 0xa8000000 /* SDRAM bank #3 */ -#define WEP_SDRAM_3_SIZE 0x00000000 /* 0 MB */ -#define WEP_SDRAM_4 0xac000000 /* SDRAM bank #4 */ -#define WEP_SDRAM_4_SIZE 0x00000000 /* 0 MB */ - -#define CONFIG_SYS_DRAM_BASE 0xa0000000 -#define CONFIG_SYS_DRAM_SIZE 0x02000000 - -/* Uncomment used SDRAM chip */ -#define WEP_SDRAM_K4S281633 -/*#define WEP_SDRAM_K4S561633*/ - - -/* - * Configuration for FLASH memory - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* number of sector in FLASH bank */ -#define WEP_FLASH_BUS_WIDTH 4 /* we use 32 bit FLASH memory... */ -#define WEP_FLASH_INTERLEAVE 2 /* ... made of 2 chips */ -#define WEP_FLASH_BANK_SIZE 0x2000000 /* size of one flash bank*/ -#define WEP_FLASH_SECT_SIZE 0x0040000 /* size of erase sector */ -#define WEP_FLASH_BASE 0x0000000 /* location of flash memory */ -#define WEP_FLASH_UNLOCK 1 /* perform hw unlock first */ - - -/* This should be defined if CFI FLASH device is present. Actually benefit - is not so clear to me. In other words we can provide more informations - to user, but this expects more complex flash handling we do not provide - now.*/ -#undef CONFIG_SYS_FLASH_CFI - -#define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ) /* timeout for Erase operation */ -#define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ) /* timeout for Write operation */ - -#define CONFIG_SYS_FLASH_BASE WEP_FLASH_BASE - -/* - * This is setting for JFFS2 support in u-boot. - * Right now there is no gain for user, but later on booting kernel might be - * possible. Consider using XIP kernel running from flash to save RAM - * footprint. - * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support. - */ -#define CONFIG_SYS_JFFS2_FIRST_BANK 0 -#define CONFIG_SYS_JFFS2_FIRST_SECTOR 5 -#define CONFIG_SYS_JFFS2_NUM_BANKS 1 - -/* - * Environment setup. Definitions of monitor location and size with - * definition of environment setup ends up in 2 possibilities. - * 1. Embeded environment - in u-boot code is space for environment - * 2. Environment is read from predefined sector of flash - * Right now we support 2. possiblity, but expecting no env placed - * on mentioned address right now. This also needs to provide whole - * sector for it - for us 256Kb is really waste of memory. U-boot uses - * default env. and until kernel parameters could be sent to kernel - * env. has no sense to us. - */ - -#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_LEN 0x20000 /* 128kb ( 1 flash sector ) */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR 0x20000 /* absolute address for now */ -#define CONFIG_ENV_SIZE 0x2000 - -#define PHYS_SDRAM_1 WEP_SDRAM_1 -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_GBL_DATA_SIZE + PHYS_SDRAM_1) - -#undef CONFIG_ENV_OVERWRITE /* env is not writable now */ - -/* - * Well this has to be defined, but on the other hand it is used differently - * one may expect. For instance loadb command do not cares :-) - * So advice is - do not relay on this... - */ -#define CONFIG_SYS_LOAD_ADDR 0x40000 - -#endif /* __CONFIG_H */ |