diff options
Diffstat (limited to 'include/configs/MVBLUE.h')
| -rw-r--r-- | include/configs/MVBLUE.h | 325 |
1 files changed, 0 insertions, 325 deletions
diff --git a/include/configs/MVBLUE.h b/include/configs/MVBLUE.h deleted file mode 100644 index aa2d9c02de..0000000000 --- a/include/configs/MVBLUE.h +++ /dev/null @@ -1,325 +0,0 @@ -/* - * (C) Copyright 2001 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define MV_VERSION "v0.2.0" - -/* LED0 = Power , LED1 = Error , LED2-5 = error code, LED6-7=00 -->PPCBoot error */ -#define ERR_NONE 0 -#define ERR_ENV 1 -#define ERR_BOOTM_BADMAGIC 2 -#define ERR_BOOTM_BADCRC 3 -#define ERR_BOOTM_GUNZIP 4 -#define ERR_BOOTP_TIMEOUT 5 -#define ERR_DHCP 6 -#define ERR_TFTP 7 -#define ERR_NOLAN 8 -#define ERR_LANDRV 9 - -#define CONFIG_BOARD_TYPES 1 -#define MVBLUE_BOARD_BOX 1 -#define MVBLUE_BOARD_LYNX 2 - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 -#define CONFIG_SYS_LDSCRIPT "board/mvblue/u-boot.lds" - -#if 0 -#define ERR_LED(code) do { if (code) \ - *(volatile char *)(0xff000003) = ( 3 | (code<<4) ) & 0xf3; \ - else \ - *(volatile char *)(0xff000003) = ( 1 ); \ -} while(0) -#else -#define ERR_LED(code) -#endif - -#define CONFIG_MPC8245 1 -#define CONFIG_MVBLUE 1 - -#define CONFIG_CLOCKS_IN_MHZ 1 - -#define CONFIG_BOARD_TYPES 1 - -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_BOOTDELAY 3 -#define CONFIG_BOOT_RETRY_TIME -1 - -#define CONFIG_AUTOBOOT_KEYED -#define CONFIG_AUTOBOOT_PROMPT \ - "autoboot in %d seconds (stop with 's')...\n", bootdelay -#define CONFIG_AUTOBOOT_STOP_STR "s" -#define CONFIG_ZERO_BOOTDELAY_CHECK -#define CONFIG_RESET_TO_RETRY 60 - - -/* - * Command line configuration. - */ - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_BOOTD -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_SAVEENV -#define CONFIG_CMD_FLASH -#define CONFIG_CMD_IMI -#define CONFIG_CMD_NET -#define CONFIG_CMD_PCI -#define CONFIG_CMD_RUN - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_NISDOMAIN -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_DNS -#define CONFIG_BOOTP_DNS2 -#define CONFIG_BOOTP_SEND_HOSTNAME -#define CONFIG_BOOTP_NTPSERVER -#define CONFIG_BOOTP_TIMEOFFSET - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ - -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_MAXARGS 16 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */ - -#define CONFIG_BOOTCOMMAND "run nfsboot" -#define CONFIG_BOOTARGS "root=/dev/mtdblock5 ro rootfstype=jffs2" - -#define CONFIG_NFSBOOTCOMMAND "bootp; run nfsargs addcons;bootm" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "console_nr=0\0" \ - "dhcp_client_id=mvBOX-XP\0" \ - "dhcp_vendor-class-identifier=mvBOX\0" \ - "adminboot=setenv bootargs root=/dev/mtdblock5 rw rootfstype=jffs2;run addcons;bootm ffc00000\0" \ - "flashboot=setenv bootargs root=/dev/mtdblock5 ro rootfstype=jffs2;run addcons;bootm ffc00000\0" \ - "safeboot=setenv bootargs root=/dev/mtdblock2 rw rootfstype=cramfs;run addcons;bootm ffc00000\0" \ - "hdboot=setenv bootargs root=/dev/hda1;run addcons;bootm ffc00000\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off\0" \ - "addcons=setenv bootargs ${bootargs} console=ttyS${console_nr},${baudrate}N8\0" \ - "mv_version=" MV_VERSION "\0" \ - "bootretry=30\0" - -#define CONFIG_OVERWRITE_ETHADDR_ONCE - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ - -#define CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE -#define CONFIG_PCI_PNP -#define CONFIG_PCI_SCAN_SHOW - -#define CONFIG_NET_RETRY_COUNT 5 - -#define CONFIG_TULIP -#define CONFIG_TULIP_FIX_DAVICOM 1 -#define CONFIG_ETHADDR b6:b4:45:eb:fb:c0 - -#define CONFIG_HW_WATCHDOG - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -#define CONFIG_SYS_FLASH_BASE 0xFFF00000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE - -#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 -#define CONFIG_SYS_EUMB_ADDR 0xFC000000 - -#define CONFIG_SYS_MONITOR_LEN 0x00100000 -#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve some kB for malloc() */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 1M ... 8M in DRAM */ - -/* Maximum amount of RAM. */ -#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000 /* 0 .. 256MB of (S)DRAM */ - - -#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE -#undef CONFIG_SYS_RAMBOOT -#else -#define CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_ISA_IO 0xFE000000 - -/* - * serial configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL - -#define CONFIG_SYS_NS16550_REG_SIZE 1 - -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_EUMB_ADDR + 0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4600) - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area - */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - * For the detail description refer to the MPC8240 user's manual. - */ - -#define CONFIG_SYS_CLK_FREQ 33000000 - -/* Bit-field values for MCCR1. */ -#define CONFIG_SYS_ROMNAL 7 -#define CONFIG_SYS_ROMFAL 11 - -/* Bit-field values for MCCR2. */ -#define CONFIG_SYS_TSWAIT 0x5 -#define CONFIG_SYS_REFINT 430 - -/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */ -#define CONFIG_SYS_BSTOPRE 121 - -/* Bit-field values for MCCR3. */ -#define CONFIG_SYS_REFREC 8 - -/* Bit-field values for MCCR4. */ -#define CONFIG_SYS_PRETOACT 3 -#define CONFIG_SYS_ACTTOPRE 5 -#define CONFIG_SYS_ACTORW 3 -#define CONFIG_SYS_SDMODE_CAS_LAT 3 -#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1 -#define CONFIG_SYS_EXTROM 1 -#define CONFIG_SYS_REGDIMM 0 -#define CONFIG_SYS_DBUS_SIZE2 1 -#define CONFIG_SYS_SDMODE_WRAP 0 - -#define CONFIG_SYS_PGMAX 0x32 -#define CONFIG_SYS_SDRAM_DSCD 0x20 - -/* Memory bank settings. - * Only bits 20-29 are actually used from these vales to set the - * start/end addresses. The upper two bits will always be 0, and the lower - * 20 bits will be 0x00000 for a start address, or 0xfffff for an end - * address. Refer to the MPC8240 book. - */ - -#define CONFIG_SYS_BANK0_START 0x00000000 -#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1) -#define CONFIG_SYS_BANK0_ENABLE 1 -#define CONFIG_SYS_BANK1_START 0x3ff00000 -#define CONFIG_SYS_BANK1_END 0x3fffffff -#define CONFIG_SYS_BANK1_ENABLE 0 -#define CONFIG_SYS_BANK2_START 0x3ff00000 -#define CONFIG_SYS_BANK2_END 0x3fffffff -#define CONFIG_SYS_BANK2_ENABLE 0 -#define CONFIG_SYS_BANK3_START 0x3ff00000 -#define CONFIG_SYS_BANK3_END 0x3fffffff -#define CONFIG_SYS_BANK3_ENABLE 0 -#define CONFIG_SYS_BANK4_START 0x3ff00000 -#define CONFIG_SYS_BANK4_END 0x3fffffff -#define CONFIG_SYS_BANK4_ENABLE 0 -#define CONFIG_SYS_BANK5_START 0x3ff00000 -#define CONFIG_SYS_BANK5_END 0x3fffffff -#define CONFIG_SYS_BANK5_ENABLE 0 -#define CONFIG_SYS_BANK6_START 0x3ff00000 -#define CONFIG_SYS_BANK6_END 0x3fffffff -#define CONFIG_SYS_BANK6_ENABLE 0 -#define CONFIG_SYS_BANK7_START 0x3ff00000 -#define CONFIG_SYS_BANK7_END 0x3fffffff -#define CONFIG_SYS_BANK7_ENABLE 0 - -#define CONFIG_SYS_ODCR 0xff - -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) - -#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U -#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#undef CONFIG_SYS_FLASH_PROTECTION -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 63 /* Max number of sectors per flash */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 12000 -#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 - - -#define CONFIG_ENV_IS_IN_FLASH - -#define CONFIG_ENV_OFFSET 0x00010000 -#define CONFIG_ENV_SIZE 0x00010000 -#define CONFIG_ENV_SECT_SIZE 0x00010000 - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif -#endif /* __CONFIG_H */ |