diff options
Diffstat (limited to 'include/configs/GENIETV.h')
| -rw-r--r-- | include/configs/GENIETV.h | 354 |
1 files changed, 0 insertions, 354 deletions
diff --git a/include/configs/GENIETV.h b/include/configs/GENIETV.h deleted file mode 100644 index 6a34b12bc6..0000000000 --- a/include/configs/GENIETV.h +++ /dev/null @@ -1,354 +0,0 @@ - /* - * A collection of structures, addresses, and values associated with - * the Motorola 860T FADS board. Copied from the MBX stuff. - * Magnus Damm added defines for 8xxrom and extended bd_info. - * Helmut Buchsbaum added bitvalues for BCSRx - * - * Copyright (c) 1998 Dan Malek (dmalek@jlc.net) - */ - -/* - * The GENIETV is using the following physical memorymap (copied from - * the FADS configuration): - * - * ff020000 -> ff02ffff : pcmcia - * ff010000 -> ff01ffff : BCSR connected to CS1, setup by 8xxROM - * ff000000 -> ff00ffff : IMAP internal in the cpu - * 30000000 -> 300fffff : flash connected to CS0 - * 00000000 -> nnnnnnnn : sdram setup by U-Boot - * - * CS pins are connected as follows: - * - * CS0 -512Kb boot flash - * CS1 - SDRAM #1 - * CS2 - SDRAM #2 - * CS3 - Flash #1 - * CS4 - Flash #2 - * CS5 - Lon (if present) - * CS6 - PCMCIA #1 - * CS7 - PCMCIA #2 - */ - -/* ------------------------------------------------------------------------- */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_SYS_TEXT_BASE 0x00000000 - -#define CONFIG_ETHADDR 08:00:22:50:70:63 /* Ethernet address */ -#define CONFIG_ENV_OVERWRITE 1 /* Overwrite the environment */ - -#define CONFIG_SYS_ALLOC_DPRAM /* Use dynamic DPRAM allocation */ - -#define CONFIG_SYS_AUTOLOAD "n" /* No autoload */ - -/*#define CONFIG_VIDEO 1 / To enable the video initialization */ -/*#define CONFIG_VIDEO_ADDR 0x00200000 */ -/*#define CONFIG_HARD_I2C 1 / I2C with hardware support */ -/*#define CONFIG_PCMCIA 1 / To enable the PCMCIA initialization */ - -/*#define CONFIG_SYS_PCMCIA_IO_ADDR 0xff020000 */ -/*#define CONFIG_SYS_PCMCIA_IO_SIZE 0x10000 */ -/*#define CONFIG_SYS_PCMCIA_MEM_ADDR 0xe0000000 */ -/*#define CONFIG_SYS_PCMCIA_MEM_SIZE 0x10000 */ - -/* Video related */ - -/*#define CONFIG_VIDEO_LOGO 1 / Show the logo */ -/*#define CONFIG_VIDEO_ENCODER_AD7177 1 / Enable this encoder */ -/*#define CONFIG_VIDEO_ENCODER_AD7177_ADDR 0xF4 / ALSB to ground */ - -/* Wireless 56Khz 4PPM keyboard on SMCx */ - -/*#define CONFIG_KEYBOARD 0 */ -/*#define CONFIG_WL_4PPM_KEYBOARD_SMC 0 / SMC to use (0 indexed) */ - -/* - * High Level Configuration Options - * (easy to change) - */ -#include <mpc8xx_irq.h> - -#define CONFIG_GENIETV 1 -#define CONFIG_MPC823 1 - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#undef CONFIG_8xx_CONS_NONE -#define CONFIG_BAUDRATE 9600 - -#define MPC8XX_FACT 12 /* Multiply by 12 */ -#define MPC8XX_XIN 5000000 /* 4 MHz clock */ - -#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT)) -#define CONFIG_SYS_PLPRCR_MF ((MPC8XX_FACT-1) << 20) -#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ /* Force it - dont measure it */ - -#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ - -#if 1 -#define CONFIG_BOOTDELAY 1 /* autoboot after 2 seconds */ -#define CONFIG_LOADS_ECHO 0 /* Dont echoes received characters */ -#define CONFIG_BOOTARGS "" -#define CONFIG_BOOTCOMMAND \ -"bootp; tftp; " \ -"setenv bootargs console=tty0 console=ttyS0 " \ -"root=/dev/nfs nfsroot=${serverip}:${rootpath} " \ -"ip=${ipaddr}:${serverip}:${gatewayip}:${subnetmask}:${hostname}:eth0:off ;" \ -"bootm " -#else -#define CONFIG_BOOTDELAY 0 /* autoboot disabled */ -#endif - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT ":>" /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 8 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 0 ... 8 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 4800, 9600, 19200, 38400, 57600, 115200 } - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xFF000000 -#define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024)) - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - * Also NOTE that it doesn't mean SDRAM - it means MEMORY. - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0x02800000 -#define CONFIG_SYS_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */ -#if 0 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 128 kB for Monitor */ -#else -#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */ -#endif -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_OFFSET 0x10000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector (64k)*/ - -/* values according to the manual */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - * -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC10) - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer * - * interrupt status bit - leave PLL multiplication factor unchanged ! - * - * #define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) - */ -#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | CONFIG_SYS_PLPRCR_MF) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF11 -#define CONFIG_SYS_SCCR (SCCR_TBS | \ - SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ - SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ - SCCR_DFALCD00) - -/*----------------------------------------------------------------------- - * - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_DER 0 - -/* Because of the way the 860 starts up and assigns CS0 the -* entire address space, we have to set the memory controller -* differently. Normally, you write the option register -* first, and then enable the chip select by writing the -* base register. For CS0, you must write the base register -* first, followed by the option register. -*/ - -/* - * Init Memory Controller: - * - * BR0 and OR0(FLASH) - */ - -#define FLASH_BASE0_PRELIM 0x02800000 /* FLASH bank #0 */ - -#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xFF800000 /* OR addr mask (512Kb) */ - -/* FLASH timing */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \ - OR_SCY_15_CLK | OR_TRLX ) - -/*#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) */ -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) /* 0xfff80ff4 */ -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_8) /* 0x02800401 */ - -/* - * BR1/2 and OR1/2 (SDRAM) -*/ - -#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00 - -#define SDRAM_MAX_SIZE 0x04000000 /* 64Mb bank */ -#define SDRAM_BASE1_PRELIM 0x00000000 /* First bank */ -#define SDRAM_BASE2_PRELIM 0x10000000 /* Second bank */ - -/* - * Memory Periodic Timer Prescaler - */ - -/* periodic timer for refresh */ -#define CONFIG_SYS_MBMR_PTB 0x5d /* start with divider for 100 MHz */ - -/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ -#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 -/* - * MBMR settings for SDRAM - */ - -/* 8 column SDRAM */ -#define CONFIG_SYS_MBMR_8COL ((CONFIG_SYS_MBMR_PTB << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_G0CLA_A11 | MAMR_RLFA_1X | MAMR_WLFA_1X \ - | MAMR_TLFA_4X) /* 0x5d802114 */ - -/* values according to the manual */ - -#define CONFIG_DRAM_50MHZ 1 -#define CONFIG_SDRAM_50MHZ - -/* We don't use the 8259. -*/ -#define NR_8259_INTS 0 - -/* - * MPC8xx CPM Options - */ -#define CONFIG_SCC_ENET 1 - -#define CONFIG_DISK_SPINUP_TIME 1000000 - -/* PCMCIA configuration */ - -#define PCMCIA_MAX_SLOTS 1 -#define PCMCIA_SLOT_B 1 - -#endif /* __CONFIG_H */ |