diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/power/Kconfig | 16 |
1 files changed, 10 insertions, 6 deletions
diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index 64e5bc2f74..911ecb1144 100644 --- a/drivers/power/Kconfig +++ b/drivers/power/Kconfig @@ -10,7 +10,7 @@ choice prompt "Select Sunxi PMIC Variant" depends on ARCH_SUNXI default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I - default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 + default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40 default AXP818_POWER if MACH_SUN8I_A83T default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I @@ -37,7 +37,7 @@ config AXP209_POWER config AXP221_POWER bool "axp221 / axp223 pmic support" - depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 + depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40 select CMD_POWEROFF ---help--- Select this to enable support for the axp221/axp223 pmic found on most @@ -70,7 +70,7 @@ endchoice config AXP_DCDC1_VOLT int "axp pmic dcdc1 voltage" depends on AXP221_POWER || AXP809_POWER || AXP818_POWER - default 3300 if AXP818_POWER + default 3300 if AXP818_POWER || MACH_SUN8I_R40 default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I ---help--- Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to @@ -97,6 +97,7 @@ config AXP_DCDC2_VOLT On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V. On A80 boards dcdc2 powers the GPU and can be left off. On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V. + On R40 boards dcdc2 is VDD-CPU and should be 1.1V config AXP_DCDC3_VOLT int "axp pmic dcdc3 voltage" @@ -104,6 +105,7 @@ config AXP_DCDC3_VOLT default 900 if AXP809_POWER || AXP818_POWER default 1500 if AXP152_POWER default 1250 if AXP209_POWER + default 1100 if MACH_SUN8I_R40 default 1200 if MACH_SUN6I || MACH_SUN8I ---help--- Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to @@ -114,6 +116,7 @@ config AXP_DCDC3_VOLT On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V. On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V. On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V. + On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V. config AXP_DCDC4_VOLT int "axp pmic dcdc4 voltage" @@ -138,13 +141,13 @@ config AXP_DCDC5_VOLT ---help--- Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to disable dcdc5. - On A23 / A31 / A33 / A80 / A83T boards dcdc5 is VCC-DRAM and + On A23 / A31 / A33 / A80 / A83T / R40 boards dcdc5 is VCC-DRAM and should be 1.5V, 1.35V if DDR3L is used. config AXP_ALDO1_VOLT int "axp pmic (a)ldo1 voltage" depends on AXP221_POWER || AXP809_POWER || AXP818_POWER - default 0 if MACH_SUN6I + default 0 if MACH_SUN6I || MACH_SUN8I_R40 default 1800 if MACH_SUN8I_A83T default 3000 if MACH_SUN8I || MACH_SUN9I ---help--- @@ -183,7 +186,8 @@ config AXP_ALDO3_VOLT Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to disable aldo3. On A10(s) / A13 / A20 boards aldo3 should be 2.8V. - On A23 / A31 / A33 boards aldo3 is VCC-PLL and AVCC and should be 3.0V. + On A23 / A31 / A33 / R40 boards aldo3 is VCC-PLL and AVCC and should + be 3.0V. On A80 boards aldo3 is normally not used. On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be 3.0V. |