diff options
Diffstat (limited to 'drivers/mtd/nand/raw/Kconfig')
| -rw-r--r-- | drivers/mtd/nand/raw/Kconfig | 297 |
1 files changed, 297 insertions, 0 deletions
diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig new file mode 100644 index 0000000000..1e4ea7bdd4 --- /dev/null +++ b/drivers/mtd/nand/raw/Kconfig @@ -0,0 +1,297 @@ + +menuconfig NAND + bool "NAND Device Support" +if NAND + +config SYS_NAND_SELF_INIT + bool + help + This option, if enabled, provides more flexible and linux-like + NAND initialization process. + +config NAND_ATMEL + bool "Support Atmel NAND controller" + imply SYS_NAND_USE_FLASH_BBT + help + Enable this driver for NAND flash platforms using an Atmel NAND + controller. + +config NAND_DAVINCI + bool "Support TI Davinci NAND controller" + help + Enable this driver for NAND flash controllers available in TI Davinci + and Keystone2 platforms + +config NAND_DENALI + bool + select SYS_NAND_SELF_INIT + imply CMD_NAND + +config NAND_DENALI_DT + bool "Support Denali NAND controller as a DT device" + select NAND_DENALI + depends on OF_CONTROL && DM + help + Enable the driver for NAND flash on platforms using a Denali NAND + controller as a DT device. + +config NAND_DENALI_SPARE_AREA_SKIP_BYTES + int "Number of bytes skipped in OOB area" + depends on NAND_DENALI + range 0 63 + help + This option specifies the number of bytes to skip from the beginning + of OOB area before last ECC sector data starts. This is potentially + used to preserve the bad block marker in the OOB area. + +config NAND_LPC32XX_SLC + bool "Support LPC32XX_SLC controller" + help + Enable the LPC32XX SLC NAND controller. + +config NAND_OMAP_GPMC + bool "Support OMAP GPMC NAND controller" + depends on ARCH_OMAP2PLUS + help + Enables omap_gpmc.c driver for OMAPx and AMxxxx platforms. + GPMC controller is used for parallel NAND flash devices, and can + do ECC calculation (not ECC error detection) for HAM1, BCH4, BCH8 + and BCH16 ECC algorithms. + +config NAND_OMAP_GPMC_PREFETCH + bool "Enable GPMC Prefetch" + depends on NAND_OMAP_GPMC + default y + help + On OMAP platforms that use the GPMC controller + (CONFIG_NAND_OMAP_GPMC_PREFETCH), this options enables the code that + uses the prefetch mode to speed up read operations. + +config NAND_OMAP_ELM + bool "Enable ELM driver for OMAPxx and AMxx platforms." + depends on NAND_OMAP_GPMC && !OMAP34XX + help + ELM controller is used for ECC error detection (not ECC calculation) + of BCH4, BCH8 and BCH16 ECC algorithms. + Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine, + thus such SoC platforms need to depend on software library for ECC error + detection. However ECC calculation on such plaforms would still be + done by GPMC controller. + +config NAND_VF610_NFC + bool "Support for Freescale NFC for VF610" + select SYS_NAND_SELF_INIT + imply CMD_NAND + help + Enables support for NAND Flash Controller on some Freescale + processors like the VF610, MCF54418 or Kinetis K70. + The driver supports a maximum 2k page size. The driver + currently does not support hardware ECC. + +choice + prompt "Hardware ECC strength" + depends on NAND_VF610_NFC + default SYS_NAND_VF610_NFC_45_ECC_BYTES + help + Select the ECC strength used in the hardware BCH ECC block. + +config SYS_NAND_VF610_NFC_45_ECC_BYTES + bool "24-error correction (45 ECC bytes)" + +config SYS_NAND_VF610_NFC_60_ECC_BYTES + bool "32-error correction (60 ECC bytes)" + +endchoice + +config NAND_PXA3XX + bool "Support for NAND on PXA3xx and Armada 370/XP/38x" + select SYS_NAND_SELF_INIT + imply CMD_NAND + help + This enables the driver for the NAND flash device found on + PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2). + +config NAND_SUNXI + bool "Support for NAND on Allwinner SoCs" + default ARCH_SUNXI + depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I + select SYS_NAND_SELF_INIT + select SYS_NAND_U_BOOT_LOCATIONS + select SPL_NAND_SUPPORT + imply CMD_NAND + ---help--- + Enable support for NAND. This option enables the standard and + SPL drivers. + The SPL driver only supports reading from the NAND using DMA + transfers. + +if NAND_SUNXI + +config NAND_SUNXI_SPL_ECC_STRENGTH + int "Allwinner NAND SPL ECC Strength" + default 64 + +config NAND_SUNXI_SPL_ECC_SIZE + int "Allwinner NAND SPL ECC Step Size" + default 1024 + +config NAND_SUNXI_SPL_USABLE_PAGE_SIZE + int "Allwinner NAND SPL Usable Page Size" + default 1024 + +endif + +config NAND_ARASAN + bool "Configure Arasan Nand" + select SYS_NAND_SELF_INIT + imply CMD_NAND + help + This enables Nand driver support for Arasan nand flash + controller. This uses the hardware ECC for read and + write operations. + +config NAND_MXC + bool "MXC NAND support" + depends on CPU_ARM926EJS || CPU_ARM1136 || MX5 + imply CMD_NAND + help + This enables the NAND driver for the NAND flash controller on the + i.MX27 / i.MX31 / i.MX5 rocessors. + +config NAND_MXS + bool "MXS NAND support" + depends on MX23 || MX28 || MX6 || MX7 + select SYS_NAND_SELF_INIT + imply CMD_NAND + select APBH_DMA + select APBH_DMA_BURST if ARCH_MX6 || ARCH_MX7 + select APBH_DMA_BURST8 if ARCH_MX6 || ARCH_MX7 + help + This enables NAND driver for the NAND flash controller on the + MXS processors. + +if NAND_MXS + +config NAND_MXS_DT + bool "Support MXS NAND controller as a DT device" + depends on OF_CONTROL && MTD + help + Enable the driver for MXS NAND flash on platforms using + device tree. + +config NAND_MXS_USE_MINIMUM_ECC + bool "Use minimum ECC strength supported by the controller" + default false + +endif + +config NAND_ZYNQ + bool "Support for Zynq Nand controller" + select SYS_NAND_SELF_INIT + imply CMD_NAND + help + This enables Nand driver support for Nand flash controller + found on Zynq SoC. + +config NAND_ZYNQ_USE_BOOTLOADER1_TIMINGS + bool "Enable use of 1st stage bootloader timing for NAND" + depends on NAND_ZYNQ + help + This flag prevent U-boot reconfigure NAND flash controller and reuse + the NAND timing from 1st stage bootloader. + +comment "Generic NAND options" + +config SYS_NAND_BLOCK_SIZE + hex "NAND chip eraseblock size" + depends on ARCH_SUNXI + help + Number of data bytes in one eraseblock for the NAND chip on the + board. This is the multiple of NAND_PAGE_SIZE and the number of + pages. + +config SYS_NAND_PAGE_SIZE + hex "NAND chip page size" + depends on ARCH_SUNXI + help + Number of data bytes in one page for the NAND chip on the + board, not including the OOB area. + +config SYS_NAND_OOBSIZE + hex "NAND chip OOB size" + depends on ARCH_SUNXI + help + Number of bytes in the Out-Of-Band area for the NAND chip on + the board. + +# Enhance depends when converting drivers to Kconfig which use this config +# option (mxc_nand, ndfc, omap_gpmc). +config SYS_NAND_BUSWIDTH_16BIT + bool "Use 16-bit NAND interface" + depends on NAND_VF610_NFC || NAND_OMAP_GPMC || NAND_MXC || ARCH_DAVINCI + help + Indicates that NAND device has 16-bit wide data-bus. In absence of this + config, bus-width of NAND device is assumed to be either 8-bit and later + determined by reading ONFI params. + Above config is useful when NAND device's bus-width information cannot + be determined from on-chip ONFI params, like in following scenarios: + - SPL boot does not support reading of ONFI parameters. This is done to + keep SPL code foot-print small. + - In current U-Boot flow using nand_init(), driver initialization + happens in board_nand_init() which is called before any device probe + (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are + not available while configuring controller. So a static CONFIG_NAND_xx + is needed to know the device's bus-width in advance. + +if SPL + +config SYS_NAND_U_BOOT_LOCATIONS + bool "Define U-boot binaries locations in NAND" + help + Enable CONFIG_SYS_NAND_U_BOOT_OFFS though Kconfig. + This option should not be enabled when compiling U-boot for boards + defining CONFIG_SYS_NAND_U_BOOT_OFFS in their include/configs/<board>.h + file. + +config SYS_NAND_U_BOOT_OFFS + hex "Location in NAND to read U-Boot from" + default 0x800000 if NAND_SUNXI + depends on SYS_NAND_U_BOOT_LOCATIONS + help + Set the offset from the start of the nand where u-boot should be + loaded from. + +config SYS_NAND_U_BOOT_OFFS_REDUND + hex "Location in NAND to read U-Boot from" + default SYS_NAND_U_BOOT_OFFS + depends on SYS_NAND_U_BOOT_LOCATIONS + help + Set the offset from the start of the nand where the redundant u-boot + should be loaded from. + +config SPL_NAND_AM33XX_BCH + bool "Enables SPL-NAND driver which supports ELM based" + depends on NAND_OMAP_GPMC && !OMAP34XX + default y + help + Hardware ECC correction. This is useful for platforms which have ELM + hardware engine and use NAND boot mode. + Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine, + so those platforms should use CONFIG_SPL_NAND_SIMPLE for enabling + SPL-NAND driver with software ECC correction support. + +config SPL_NAND_DENALI + bool "Support Denali NAND controller for SPL" + help + This is a small implementation of the Denali NAND controller + for use on SPL. + +config SPL_NAND_SIMPLE + bool "Use simple SPL NAND driver" + depends on !SPL_NAND_AM33XX_BCH + help + Support for NAND boot using simple NAND drivers that + expose the cmd_ctrl() interface. +endif + +endif # if NAND |