diff options
Diffstat (limited to 'doc/README.nand')
| -rw-r--r-- | doc/README.nand | 60 |
1 files changed, 60 insertions, 0 deletions
diff --git a/doc/README.nand b/doc/README.nand index b91f1985d1..70cf768d23 100644 --- a/doc/README.nand +++ b/doc/README.nand @@ -190,6 +190,24 @@ Configuration Options: This is used by SoC platforms which do not have built-in ELM hardware engine required for BCH ECC correction. + CONFIG_SYS_NAND_BUSWIDTH_16BIT + Indicates that NAND device has 16-bit wide data-bus. In absence of this + config, bus-width of NAND device is assumed to be either 8-bit and later + determined by reading ONFI params. + Above config is useful when NAND device's bus-width information cannot + be determined from on-chip ONFI params, like in following scenarios: + - SPL boot does not support reading of ONFI parameters. This is done to + keep SPL code foot-print small. + - In current U-Boot flow using nand_init(), driver initialization + happens in board_nand_init() which is called before any device probe + (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are + not available while configuring controller. So a static CONFIG_NAND_xx + is needed to know the device's bus-width in advance. + Some drivers using above config are: + drivers/mtd/nand/mxc_nand.c + drivers/mtd/nand/ndfc.c + drivers/mtd/nand/omap_gpmc.c + Platform specific options ========================= @@ -231,6 +249,48 @@ Platform specific options 8-bit BCH code with - ecc calculation using GPMC hardware engine, - error detection using ELM hardware engine. + OMAP_ECC_BCH16_CODE_HW + 16-bit BCH code with + - ecc calculation using GPMC hardware engine, + - error detection using ELM hardware engine. + + How to select ECC scheme on OMAP and AMxx platforms ? + ----------------------------------------------------- + Though higher ECC schemes have more capability to detect and correct + bit-flips, but still selection of ECC scheme is dependent on following + - hardware engines present in SoC. + Some legacy OMAP SoC do not have ELM h/w engine thus such + SoC cannot support BCHx_HW ECC schemes. + - size of OOB/Spare region + With higher ECC schemes, more OOB/Spare area is required to + store ECC. So choice of ECC scheme is limited by NAND oobsize. + + In general following expression can help: + NAND_OOBSIZE >= 2 + (NAND_PAGESIZE / 512) * ECC_BYTES + where + NAND_OOBSIZE = number of bytes available in + OOB/spare area per NAND page. + NAND_PAGESIZE = bytes in main-area of NAND page. + ECC_BYTES = number of ECC bytes generated to + protect 512 bytes of data, which is: + 3 for HAM1_xx ecc schemes + 7 for BCH4_xx ecc schemes + 14 for BCH8_xx ecc schemes + 26 for BCH16_xx ecc schemes + + example to check for BCH16 on 2K page NAND + NAND_PAGESIZE = 2048 + NAND_OOBSIZE = 64 + 2 + (2048 / 512) * 26 = 106 > NAND_OOBSIZE + Thus BCH16 cannot be supported on 2K page NAND. + + However, for 4K pagesize NAND + NAND_PAGESIZE = 4096 + NAND_OOBSIZE = 64 + ECC_BYTES = 26 + 2 + (4096 / 512) * 26 = 210 < NAND_OOBSIZE + Thus BCH16 can be supported on 4K page NAND. + NOTE: ===== |