summaryrefslogtreecommitdiffstats
path: root/board/spc1920/spc1920.c
diff options
context:
space:
mode:
Diffstat (limited to 'board/spc1920/spc1920.c')
-rw-r--r--board/spc1920/spc1920.c248
1 files changed, 0 insertions, 248 deletions
diff --git a/board/spc1920/spc1920.c b/board/spc1920/spc1920.c
deleted file mode 100644
index 1775433f0d..0000000000
--- a/board/spc1920/spc1920.c
+++ /dev/null
@@ -1,248 +0,0 @@
-/*
- * (C) Copyright 2000-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-#include <common.h>
-#include <mpc8xx.h>
-#include "pld.h"
-#include "hpi.h"
-
-#define _NOT_USED_ 0xFFFFFFFF
-
-static long int dram_size (long int, long int *, long int);
-
-const uint sdram_table[] = {
- /*
- * Single Read. (Offset 0 in UPMB RAM)
- */
- 0x1F07FC04, 0xEEAEFC04, 0x11ADFC04, 0xEFBBBC00,
- 0x1FF77C47, /* last */
- /*
- * SDRAM Initialization (offset 5 in UPMB RAM)
- *
- * This is no UPM entry point. The following definition uses
- * the remaining space to establish an initialization
- * sequence, which is executed by a RUN command.
- *
- */
- 0x1FF77C34, 0xEFEABC34, 0x1FB57C35, /* last */
- /*
- * Burst Read. (Offset 8 in UPMB RAM)
- */
- 0x1F07FC04, 0xEEAEFC04, 0x10ADFC04, 0xF0AFFC00,
- 0xF0AFFC00, 0xF1AFFC00, 0xEFBBBC00, 0x1FF77C47, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Single Write. (Offset 18 in UPMB RAM)
- */
- 0x1F07FC04, 0xEEAEBC00, 0x01B93C04, 0x1FF77C47, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Burst Write. (Offset 20 in UPMB RAM)
- */
- 0x1F07FC04, 0xEEAEBC00, 0x10AD7C00, 0xF0AFFC00,
- 0xF0AFFC00, 0xE1BBBC04, 0x1FF77C47, /* last */
- _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Refresh (Offset 30 in UPMB RAM)
- */
- 0x1FF5FC84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
- 0xFFFFFC84, 0xFFFFFC07, /* last */
- _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Exception. (Offset 3c in UPMB RAM)
- */
- 0x7FFFFC07, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_,
-};
-
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immr->im_memctl;
- /* volatile spc1920_pld_t *pld = (spc1920_pld_t *) CONFIG_SYS_SPC1920_PLD_BASE; */
-
- long int size_b0;
- long int size8, size9;
- int i;
-
- /*
- * Configure UPMB for SDRAM
- */
- upmconfig (UPMB, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
-
- udelay(100);
-
- memctl->memc_mptpr = CONFIG_SYS_MPTPR;
-
- /* burst length=4, burst type=sequential, CAS latency=2 */
- memctl->memc_mar = CONFIG_SYS_MAR;
-
- /*
- * Map controller bank 1 to the SDRAM bank at preliminary address.
- */
- memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
- memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
-
- /* initialize memory address register */
- memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL; /* refresh not enabled yet */
-
- /* mode initialization (offset 5) */
- udelay (200); /* 0x80006105 */
- memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x05);
-
- /* run 2 refresh sequence with 4-beat refresh burst (offset 0x30) */
- udelay (1); /* 0x80006130 */
- memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
- udelay (1); /* 0x80006130 */
- memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
- udelay (1); /* 0x80006106 */
- memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x06);
-
- memctl->memc_mbmr |= MBMR_PTBE; /* refresh enabled */
-
- udelay (200);
-
- /* Need at least 10 DRAM accesses to stabilize */
- for (i = 0; i < 10; ++i) {
- volatile unsigned long *addr =
- (volatile unsigned long *) CONFIG_SYS_SDRAM_BASE;
- unsigned long val;
-
- val = *(addr + i);
- *(addr + i) = val;
- }
-
- /*
- * Check Bank 0 Memory Size for re-configuration
- *
- * try 8 column mode
- */
- size8 = dram_size (CONFIG_SYS_MBMR_8COL, (long *)CONFIG_SYS_SDRAM_BASE, SDRAM_MAX_SIZE);
-
- udelay (1000);
-
- /*
- * try 9 column mode
- */
- size9 = dram_size (CONFIG_SYS_MBMR_9COL, (long *)CONFIG_SYS_SDRAM_BASE, SDRAM_MAX_SIZE);
-
- if (size8 < size9) { /* leave configuration at 9 columns */
- size_b0 = size9;
- memctl->memc_mbmr = CONFIG_SYS_MBMR_9COL | MBMR_PTBE;
- udelay (500);
- } else { /* back to 8 columns */
- size_b0 = size8;
- memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL | MBMR_PTBE;
- udelay (500);
- }
-
- /*
- * Final mapping:
- */
-
- memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) |
- OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING;
- memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMB | BR_V;
- udelay (1000);
-
- /* initalize the DSP Host Port Interface */
- hpi_init();
-
- /* FRAM Setup */
- memctl->memc_or4 = CONFIG_SYS_OR4;
- memctl->memc_br4 = CONFIG_SYS_BR4;
- udelay(1000);
-
- return (size_b0);
-}
-
-/*
- * Check memory range for valid RAM. A simple memory test determines
- * the actually available RAM size between addresses `base' and
- * `base + maxsize'. Some (not all) hardware errors are detected:
- * - short between address lines
- * - short between data lines
- */
-static long int dram_size (long int mbmr_value, long int *base,
- long int maxsize)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
-
- memctl->memc_mbmr = mbmr_value;
-
- return (get_ram_size (base, maxsize));
-}
-
-
-/************* other stuff ******************/
-
-
-int board_early_init_f(void)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-
- /* Set Go/NoGo led (PA15) to color red */
- immap->im_ioport.iop_papar &= ~0x1;
- immap->im_ioport.iop_paodr &= ~0x1;
- immap->im_ioport.iop_padir |= 0x1;
- immap->im_ioport.iop_padat |= 0x1;
-
-#if 0
- /* Turn on LED PD9 */
- immap->im_ioport.iop_pdpar &= ~(0x0040);
- immap->im_ioport.iop_pddir |= 0x0040;
- immap->im_ioport.iop_pddat |= 0x0040;
-#endif
-
- /*
- * Enable console on SMC1. This requires turning on
- * the com2_en signal and SMC1_DISABLE
- */
-
- /* SMC1_DISABLE: PB17 */
- immap->im_cpm.cp_pbodr &= ~0x4000;
- immap->im_cpm.cp_pbpar &= ~0x4000;
- immap->im_cpm.cp_pbdir |= 0x4000;
- immap->im_cpm.cp_pbdat &= ~0x4000;
-
- /* COM2_EN: PD10 */
- immap->im_ioport.iop_pdpar &= ~0x0020;
- immap->im_ioport.iop_pddir &= ~0x4000;
- immap->im_ioport.iop_pddir |= 0x0020;
- immap->im_ioport.iop_pddat |= 0x0020;
-
-
-#ifdef CONFIG_SYS_SMC1_PLD_CLK4 /* SMC1 uses CLK4 from PLD */
- immap->im_cpm.cp_simode |= 0x7000;
- immap->im_cpm.cp_simode &= ~(0x8000);
-#endif
-
- return 0;
-}
-
-int last_stage_init(void)
-{
-#ifdef CONFIG_SPC1920_HPI_TEST
- printf("CMB1920 Host Port Interface Test: %s\n",
- hpi_test() ? "Failed!" : "OK");
-#endif
- return 0;
-}
-
-int checkboard (void)
-{
- puts("Board: SPC1920\n");
- return 0;
-}
generated by cgit (git 2.34.1) at 2024-05-27 19:11:13 +0000