diff options
Diffstat (limited to 'board/freescale/common/vid.c')
| -rw-r--r-- | board/freescale/common/vid.c | 24 |
1 files changed, 12 insertions, 12 deletions
diff --git a/board/freescale/common/vid.c b/board/freescale/common/vid.c index 2617f61520..20f5421da0 100644 --- a/board/freescale/common/vid.c +++ b/board/freescale/common/vid.c @@ -65,14 +65,14 @@ static int find_ir_chip_on_i2c(void) u8 byte; int i; const int ir_i2c_addr[] = {0x38, 0x08, 0x09}; -#ifdef CONFIG_DM_I2C +#if CONFIG_IS_ENABLED(DM_I2C) struct udevice *dev; #endif /* Check all the address */ for (i = 0; i < (sizeof(ir_i2c_addr)/sizeof(ir_i2c_addr[0])); i++) { i2caddress = ir_i2c_addr[i]; -#ifndef CONFIG_DM_I2C +#if !CONFIG_IS_ENABLED(DM_I2C) ret = i2c_read(i2caddress, IR36021_MFR_ID_OFFSET, 1, (void *)&byte, sizeof(byte)); @@ -117,12 +117,12 @@ static int read_voltage_from_INA220(int i2caddress) int i, ret, voltage_read = 0; u16 vol_mon; u8 buf[2]; -#ifdef CONFIG_DM_I2C +#if CONFIG_IS_ENABLED(DM_I2C) struct udevice *dev; #endif for (i = 0; i < NUM_READINGS; i++) { -#ifndef CONFIG_DM_I2C +#if !CONFIG_IS_ENABLED(DM_I2C) ret = i2c_read(I2C_VOL_MONITOR_ADDR, I2C_VOL_MONITOR_BUS_V_OFFSET, 1, (void *)&buf, 2); @@ -160,12 +160,12 @@ static int read_voltage_from_IR(int i2caddress) int i, ret, voltage_read = 0; u16 vol_mon; u8 buf; -#ifdef CONFIG_DM_I2C +#if CONFIG_IS_ENABLED(DM_I2C) struct udevice *dev; #endif for (i = 0; i < NUM_READINGS; i++) { -#ifndef CONFIG_DM_I2C +#if !CONFIG_IS_ENABLED(DM_I2C) ret = i2c_read(i2caddress, IR36021_LOOP1_VOUT_OFFSET, 1, (void *)&buf, 1); @@ -213,7 +213,7 @@ static int read_voltage_from_LTC(int i2caddress) int ret, vcode = 0; u8 chan = PWM_CHANNEL0; -#ifndef CONFIG_DM_I2C +#if !CONFIG_IS_ENABLED(DM_I2C) /* select the PAGE 0 using PMBus commands PAGE for VDD*/ ret = i2c_write(I2C_VOL_MONITOR_ADDR, PMBUS_CMD_PAGE, 1, &chan, 1); @@ -229,7 +229,7 @@ static int read_voltage_from_LTC(int i2caddress) return ret; } -#ifndef CONFIG_DM_I2C +#if !CONFIG_IS_ENABLED(DM_I2C) /*read the output voltage using PMBus command READ_VOUT*/ ret = i2c_read(I2C_VOL_MONITOR_ADDR, PMBUS_CMD_READ_VOUT, 1, (void *)&vcode, 2); @@ -344,7 +344,7 @@ static int set_voltage_to_IR(int i2caddress, int vdd) vid = DIV_ROUND_UP(vdd - 245, 5); #endif -#ifndef CONFIG_DM_I2C +#if !CONFIG_IS_ENABLED(DM_I2C) ret = i2c_write(i2caddress, IR36021_LOOP1_MANUAL_ID_OFFSET, 1, (void *)&vid, sizeof(vid)); #else @@ -392,7 +392,7 @@ static int set_voltage_to_LTC(int i2caddress, int vdd) vdd & 0xFF, (vdd & 0xFF00) >> 8}; /* Write the desired voltage code to the regulator */ -#ifndef CONFIG_DM_I2C +#if !CONFIG_IS_ENABLED(DM_I2C) /* Check write protect state */ ret = i2c_read(I2C_VOL_MONITOR_ADDR, PMBUS_CMD_WRITE_PROTECT, 1, @@ -621,7 +621,7 @@ int adjust_vdd(ulong vdd_override) } /* check IR chip work on Intel mode*/ -#ifndef CONFIG_DM_I2C +#if !CONFIG_IS_ENABLED(DM_I2C) ret = i2c_read(i2caddress, IR36021_INTEL_MODE_OOFSET, 1, (void *)&buf, 1); @@ -803,7 +803,7 @@ int adjust_vdd(ulong vdd_override) } /* check IR chip work on Intel mode*/ -#ifndef CONFIG_DM_I2C +#if !CONFIG_IS_ENABLED(DM_I2C) ret = i2c_read(i2caddress, IR36021_INTEL_MODE_OOFSET, 1, (void *)&buf, 1); |