diff options
Diffstat (limited to 'board/Marvell/openrd/openrd.c')
| -rw-r--r-- | board/Marvell/openrd/openrd.c | 160 |
1 files changed, 160 insertions, 0 deletions
diff --git a/board/Marvell/openrd/openrd.c b/board/Marvell/openrd/openrd.c new file mode 100644 index 0000000000..17a65600e4 --- /dev/null +++ b/board/Marvell/openrd/openrd.c @@ -0,0 +1,160 @@ +/* + * (C) Copyright 2009 + * Net Insight <www.netinsight.net> + * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net> + * + * Based on sheevaplug.c: + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Prafulla Wadaskar <prafulla@marvell.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <miiphy.h> +#include <asm/arch/cpu.h> +#include <asm/arch/soc.h> +#include <asm/arch/mpp.h> +#include "openrd.h" + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + /* + * default gpio configuration + * There are maximum 64 gpios controlled through 2 sets of registers + * the below configuration configures mainly initial LED status + */ + mvebu_config_gpio(OPENRD_OE_VAL_LOW, + OPENRD_OE_VAL_HIGH, + OPENRD_OE_LOW, OPENRD_OE_HIGH); + + /* Multi-Purpose Pins Functionality configuration */ + static const u32 kwmpp_config[] = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_GPO, + MPP8_TW_SDA, + MPP9_TW_SCK, + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_SD_CLK, + MPP13_SD_CMD, /* Alt UART1_TXD */ + MPP14_SD_D0, /* Alt UART1_RXD */ + MPP15_SD_D1, + MPP16_SD_D2, + MPP17_SD_D3, + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_GE1_0, + MPP21_GE1_1, + MPP22_GE1_2, + MPP23_GE1_3, + MPP24_GE1_4, + MPP25_GE1_5, + MPP26_GE1_6, + MPP27_GE1_7, + MPP28_GPIO, + MPP29_TSMP9, + MPP30_GE1_10, + MPP31_GE1_11, + MPP32_GE1_12, + MPP33_GE1_13, + MPP34_GPIO, /* UART1 / SD sel */ + MPP35_TDM_CH0_TX_QL, + MPP36_TDM_SPI_CS1, + MPP37_TDM_CH2_TX_QL, + MPP38_TDM_CH2_RX_QL, + MPP39_AUDIO_I2SBCLK, + MPP40_AUDIO_I2SDO, + MPP41_AUDIO_I2SLRC, + MPP42_AUDIO_I2SMCLK, + MPP43_AUDIO_I2SDI, + MPP44_AUDIO_EXTCLK, + MPP45_TDM_PCLK, + MPP46_TDM_FS, + MPP47_TDM_DRX, + MPP48_TDM_DTX, + MPP49_TDM_CH0_RX_QL, + 0 + }; + + kirkwood_mpp_conf(kwmpp_config, NULL); + return 0; +} + +int board_init(void) +{ + /* + * arch number of board + */ +#if defined(CONFIG_BOARD_IS_OPENRD_BASE) + gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE; +#elif defined(CONFIG_BOARD_IS_OPENRD_CLIENT) + gd->bd->bi_arch_number = MACH_TYPE_OPENRD_CLIENT; +#elif defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE) + gd->bd->bi_arch_number = MACH_TYPE_OPENRD_ULTIMATE; +#endif + + /* adress of boot parameters */ + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; + return 0; +} + +#ifdef CONFIG_RESET_PHY_R +/* Configure and enable MV88E1116/88E1121 PHY */ +void mv_phy_init(char *name) +{ + u16 reg; + u16 devadr; + + if (miiphy_set_current_dev(name)) + return; + + /* command to read PHY dev address */ + if (miiphy_read(name, 0xEE, 0xEE, (u16 *)&devadr)) { + printf("Err..%s could not read PHY dev address\n", __func__); + return; + } + + /* + * Enable RGMII delay on Tx and Rx for CPU port + * Ref: sec 4.7.2 of chip datasheet + */ + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); + miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); + reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); + miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); + + /* reset the phy */ + miiphy_reset(name, devadr); + + printf(PHY_NO" Initialized on %s\n", name); +} + +void reset_phy(void) +{ + mv_phy_init("egiga0"); + +#ifdef CONFIG_BOARD_IS_OPENRD_CLIENT + /* Kirkwood ethernet driver is written with the assumption that in case + * of multiple PHYs, their addresses are consecutive. But unfortunately + * in case of OpenRD-Client, PHY addresses are not consecutive.*/ + miiphy_write("egiga1", 0xEE, 0xEE, 24); +#endif + +#if defined(CONFIG_BOARD_IS_OPENRD_CLIENT) || \ + defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE) + /* configure and initialize both PHY's */ + mv_phy_init("egiga1"); +#endif +} +#endif /* CONFIG_RESET_PHY_R */ |