diff options
32 files changed, 103 insertions, 226 deletions
diff --git a/board/atmel/at91rm9200ek/at91rm9200ek.c b/board/atmel/at91rm9200ek/at91rm9200ek.c index 64ab572619..4ca8106c06 100644 --- a/board/atmel/at91rm9200ek/at91rm9200ek.c +++ b/board/atmel/at91rm9200ek/at91rm9200ek.c @@ -14,7 +14,6 @@ #include <netdev.h> #include <asm/arch/hardware.h> #include <asm/arch/at91_pio.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/at91_common.h> #include <asm/io.h> diff --git a/board/atmel/at91rm9200ek/led.c b/board/atmel/at91rm9200ek/led.c index 6761b141fb..fbe8e3d22c 100644 --- a/board/atmel/at91rm9200ek/led.c +++ b/board/atmel/at91rm9200ek/led.c @@ -12,7 +12,7 @@ #include <common.h> #include <asm/io.h> #include <asm/arch/hardware.h> -#include <asm/arch/at91_pmc.h> +#include <asm/arch/clk.h> #include <asm/arch/at91_pio.h> #include <status_led.h> @@ -59,11 +59,9 @@ void red_led_off(void) void coloured_LED_init (void) { - at91_pmc_t *pmc = (at91_pmc_t *)ATMEL_BASE_PMC; at91_pio_t *pio = (at91_pio_t *)ATMEL_BASE_PIO; - /* Enable PIOB clock */ - writel(1 << ATMEL_ID_PIOB, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOB); /* Disable peripherals on LEDs */ writel(GREEN_LED | YELLOW_LED | RED_LED, &pio->piob.per); diff --git a/board/atmel/at91sam9260ek/at91sam9260ek.c b/board/atmel/at91sam9260ek/at91sam9260ek.c index 7f14af1011..98193bfdc6 100644 --- a/board/atmel/at91sam9260ek/at91sam9260ek.c +++ b/board/atmel/at91sam9260ek/at91sam9260ek.c @@ -11,7 +11,7 @@ #include <asm/arch/at91sam9260_matrix.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> +#include <asm/arch/clk.h> #include <asm/arch/gpio.h> #include <atmel_mci.h> @@ -70,11 +70,9 @@ static void at91sam9260ek_nand_hw_init(void) #ifdef CONFIG_MACB static void at91sam9260ek_macb_hw_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA; - /* Enable EMAC clock */ - writel(1 << ATMEL_ID_EMAC0, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_EMAC0); /* * Disable pull-up on: @@ -122,12 +120,9 @@ int board_mmc_init(bd_t *bd) int board_early_init_f(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - - /* Enable clocks for all PIOs */ - writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) | - (1 << ATMEL_ID_PIOC), - &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOA); + at91_periph_clk_enable(ATMEL_ID_PIOB); + at91_periph_clk_enable(ATMEL_ID_PIOC); return 0; } diff --git a/board/atmel/at91sam9261ek/at91sam9261ek.c b/board/atmel/at91sam9261ek/at91sam9261ek.c index 52504742cd..7b7cd2c426 100644 --- a/board/atmel/at91sam9261ek/at91sam9261ek.c +++ b/board/atmel/at91sam9261ek/at91sam9261ek.c @@ -12,7 +12,6 @@ #include <asm/arch/at91sam9261_matrix.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> #include <asm/arch/clk.h> #include <asm/arch/gpio.h> @@ -35,7 +34,6 @@ static void at91sam9261ek_nand_hw_init(void) { struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; unsigned long csa; /* Enable CS3 */ @@ -74,7 +72,7 @@ static void at91sam9261ek_nand_hw_init(void) AT91_SMC_MODE_TDF_CYCLE(2), &smc->cs[3].mode); - writel(1 << ATMEL_ID_PIOC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOC); /* Configure RDY/BSY */ at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); @@ -161,8 +159,6 @@ void lcd_disable(void) static void at91sam9261ek_lcd_hw_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - at91_set_A_periph(AT91_PIN_PB1, 0); /* LCDHSYNC */ at91_set_A_periph(AT91_PIN_PB2, 0); /* LCDDOTCK */ at91_set_A_periph(AT91_PIN_PB3, 0); /* LCDDEN */ @@ -186,7 +182,7 @@ static void at91sam9261ek_lcd_hw_init(void) at91_set_B_periph(AT91_PIN_PB27, 0); /* LCDD22 */ at91_set_B_periph(AT91_PIN_PB28, 0); /* LCDD23 */ - writel(AT91_PMC_HCK1, &pmc->scer); + at91_system_clk_enable(AT91_PMC_HCK1); /* For 9G10EK, let U-Boot allocate the framebuffer in SDRAM */ #ifdef CONFIG_AT91SAM9261EK diff --git a/board/atmel/at91sam9261ek/led.c b/board/atmel/at91sam9261ek/led.c index 18a68d8c59..485d7ea81f 100644 --- a/board/atmel/at91sam9261ek/led.c +++ b/board/atmel/at91sam9261ek/led.c @@ -8,17 +8,15 @@ #include <common.h> #include <asm/arch/at91sam9261.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/gpio.h> #include <asm/arch/at91_pio.h> +#include <asm/arch/clk.h> #include <asm/io.h> void coloured_LED_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - /* Enable clock */ - writel(ATMEL_ID_PIOA, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOA); at91_set_gpio_output(CONFIG_RED_LED, 1); at91_set_gpio_output(CONFIG_GREEN_LED, 1); diff --git a/board/atmel/at91sam9263ek/at91sam9263ek.c b/board/atmel/at91sam9263ek/at91sam9263ek.c index 927adb0d38..af68e10390 100644 --- a/board/atmel/at91sam9263ek/at91sam9263ek.c +++ b/board/atmel/at91sam9263ek/at91sam9263ek.c @@ -11,7 +11,6 @@ #include <asm/arch/at91sam9263.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/at91_matrix.h> #include <asm/arch/at91_pio.h> #include <asm/arch/clk.h> @@ -39,7 +38,6 @@ static void at91sam9263ek_nand_hw_init(void) unsigned long csa; at91_smc_t *smc = (at91_smc_t *) ATMEL_BASE_SMC0; at91_matrix_t *matrix = (at91_matrix_t *) ATMEL_BASE_MATRIX; - at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; /* Enable CS3 */ csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A; @@ -68,8 +66,8 @@ static void at91sam9263ek_nand_hw_init(void) AT91_SMC_MODE_TDF_CYCLE(2), &smc->cs[3].mode); - writel(1 << ATMEL_ID_PIOA | 1 << ATMEL_ID_PIOCDE, - &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOA); + at91_periph_clk_enable(ATMEL_ID_PIOCDE); /* Configure RDY/BSY */ at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); @@ -82,11 +80,9 @@ static void at91sam9263ek_nand_hw_init(void) #ifdef CONFIG_MACB static void at91sam9263ek_macb_hw_init(void) { - at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO; - /* Enable clock */ - writel(1 << ATMEL_ID_EMAC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_EMAC); /* * Disable pull-up on: @@ -139,8 +135,6 @@ void lcd_disable(void) static void at91sam9263ek_lcd_hw_init(void) { - at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; - at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* LCDHSYNC */ at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* LCDDOTCK */ at91_set_a_periph(AT91_PIO_PORTC, 3, 0); /* LCDDEN */ @@ -164,7 +158,7 @@ static void at91sam9263ek_lcd_hw_init(void) at91_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDD22 */ at91_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDD23 */ - writel(1 << ATMEL_ID_LCDC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_LCDC); gd->fb_base = ATMEL_BASE_SRAM0; } @@ -226,12 +220,9 @@ int board_mmc_init(bd_t *bd) int board_early_init_f(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - - /* Enable clocks for all PIOs */ - writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) | - (1 << ATMEL_ID_PIOCDE), - &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOA); + at91_periph_clk_enable(ATMEL_ID_PIOB); + at91_periph_clk_enable(ATMEL_ID_PIOCDE); at91_seriald_hw_init(); return 0; diff --git a/board/atmel/at91sam9263ek/led.c b/board/atmel/at91sam9263ek/led.c index e317d99831..21d81def5e 100644 --- a/board/atmel/at91sam9263ek/led.c +++ b/board/atmel/at91sam9263ek/led.c @@ -9,16 +9,13 @@ #include <common.h> #include <asm/io.h> #include <asm/arch/gpio.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/at91sam9263.h> +#include <asm/arch/clk.h> void coloured_LED_init(void) { - /* Enable clock */ - at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; - - writel(1 << ATMEL_ID_PIOB | 1 << ATMEL_ID_PIOCDE, - &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOB); + at91_periph_clk_enable(ATMEL_ID_PIOB); at91_set_gpio_output(CONFIG_RED_LED, 1); at91_set_gpio_output(CONFIG_GREEN_LED, 1); diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c index 0a51fcd9aa..4c6431266f 100644 --- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c +++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c @@ -12,7 +12,6 @@ #include <asm/arch/at91sam9g45_matrix.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/gpio.h> #include <asm/arch/clk.h> #include <lcd.h> @@ -36,7 +35,6 @@ void at91sam9m10g45ek_nand_hw_init(void) { struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; unsigned long csa; /* Enable CS3 */ @@ -63,7 +61,7 @@ void at91sam9m10g45ek_nand_hw_init(void) AT91_SMC_MODE_TDF_CYCLE(3), &smc->cs[3].mode); - writel(1 << ATMEL_ID_PIOC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOC); /* Configure RDY/BSY */ at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); @@ -130,13 +128,11 @@ static void ddr2_conf(struct atmel_mpddrc_config *ddr2) void mem_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; struct atmel_mpddrc_config ddr2; ddr2_conf(&ddr2); - /* enable DDR2 clock */ - writel(AT91_PMC_DDR, &pmc->scer); + at91_system_clk_enable(AT91_PMC_DDR); /* DDRAM2 Controller initialize */ ddr2_init(ATMEL_BASE_DDRSDRC0, ATMEL_BASE_CS6, &ddr2); @@ -146,9 +142,7 @@ void mem_init(void) #ifdef CONFIG_CMD_USB static void at91sam9m10g45ek_usb_hw_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - - writel(1 << ATMEL_ID_PIODE, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIODE); at91_set_gpio_output(AT91_PIN_PD1, 0); at91_set_gpio_output(AT91_PIN_PD3, 0); @@ -158,11 +152,9 @@ static void at91sam9m10g45ek_usb_hw_init(void) #ifdef CONFIG_MACB static void at91sam9m10g45ek_macb_hw_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA; - /* Enable clock */ - writel(1 << ATMEL_ID_EMAC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_EMAC); /* * Disable pull-up on: @@ -222,8 +214,6 @@ void lcd_disable(void) static void at91sam9m10g45ek_lcd_hw_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - at91_set_A_periph(AT91_PIN_PE0, 0); /* LCDDPWR */ at91_set_A_periph(AT91_PIN_PE2, 0); /* LCDCC */ at91_set_A_periph(AT91_PIN_PE3, 0); /* LCDVSYNC */ @@ -255,7 +245,7 @@ static void at91sam9m10g45ek_lcd_hw_init(void) at91_set_A_periph(AT91_PIN_PE29, 0); /* LCDD22 */ at91_set_A_periph(AT91_PIN_PE30, 0); /* LCDD23 */ - writel(1 << ATMEL_ID_LCDC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_LCDC); gd->fb_base = CONFIG_AT91SAM9G45_LCD_BASE; } diff --git a/board/atmel/at91sam9m10g45ek/led.c b/board/atmel/at91sam9m10g45ek/led.c index fe98723962..866052ee1c 100644 --- a/board/atmel/at91sam9m10g45ek/led.c +++ b/board/atmel/at91sam9m10g45ek/led.c @@ -9,15 +9,12 @@ #include <common.h> #include <asm/io.h> #include <asm/arch/at91sam9g45.h> -#include <asm/arch/at91_pmc.h> +#include <asm/arch/clk.h> #include <asm/arch/gpio.h> void coloured_LED_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - - /* Enable clock */ - writel(1 << ATMEL_ID_PIODE, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIODE); at91_set_gpio_output(CONFIG_RED_LED, 1); at91_set_gpio_output(CONFIG_GREEN_LED, 1); diff --git a/board/atmel/at91sam9n12ek/at91sam9n12ek.c b/board/atmel/at91sam9n12ek/at91sam9n12ek.c index 0b0177df2b..d3555bbdf6 100644 --- a/board/atmel/at91sam9n12ek/at91sam9n12ek.c +++ b/board/atmel/at91sam9n12ek/at91sam9n12ek.c @@ -10,7 +10,6 @@ #include <asm/arch/at91sam9x5_matrix.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> #include <asm/arch/at91_pio.h> #include <asm/arch/clk.h> @@ -208,9 +207,8 @@ void at91sam9n12ek_usb_hw_init(void) int board_early_init_f(void) { - /* Enable clocks for all PIOs */ - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - writel((1 << ATMEL_ID_PIOAB) | (1 << ATMEL_ID_PIOCD), &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOAB); + at91_periph_clk_enable(ATMEL_ID_PIOCD); at91_seriald_hw_init(); return 0; diff --git a/board/atmel/at91sam9rlek/at91sam9rlek.c b/board/atmel/at91sam9rlek/at91sam9rlek.c index f995cef1e2..9ef2864bb1 100644 --- a/board/atmel/at91sam9rlek/at91sam9rlek.c +++ b/board/atmel/at91sam9rlek/at91sam9rlek.c @@ -12,7 +12,6 @@ #include <asm/arch/at91sam9rl_matrix.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> #include <asm/arch/clk.h> #include <asm/arch/gpio.h> @@ -36,7 +35,6 @@ static void at91sam9rlek_nand_hw_init(void) { struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; unsigned long csa; /* Enable CS3 */ @@ -64,7 +62,7 @@ static void at91sam9rlek_nand_hw_init(void) AT91_SMC_MODE_TDF_CYCLE(2), &smc->cs[3].mode); - writel(1 << ATMEL_ID_PIOD, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOD); /* Configure RDY/BSY */ at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); @@ -106,8 +104,6 @@ void lcd_disable(void) } static void at91sam9rlek_lcd_hw_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - at91_set_B_periph(AT91_PIN_PC1, 0); /* LCDPWR */ at91_set_A_periph(AT91_PIN_PC5, 0); /* LCDHSYNC */ at91_set_A_periph(AT91_PIN_PC6, 0); /* LCDDOTCK */ @@ -130,7 +126,7 @@ static void at91sam9rlek_lcd_hw_init(void) at91_set_B_periph(AT91_PIN_PC24, 0); /* LCDD22 */ at91_set_B_periph(AT91_PIN_PC25, 0); /* LCDD23 */ - writel(1 << ATMEL_ID_LCDC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_LCDC); } #ifdef CONFIG_LCD_INFO @@ -174,12 +170,10 @@ int board_mmc_init(bd_t *bis) int board_early_init_f(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - - /* Enable clocks for all PIOs */ - writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) | - (1 << ATMEL_ID_PIOC) | (1 << ATMEL_ID_PIOD), - &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOA); + at91_periph_clk_enable(ATMEL_ID_PIOB); + at91_periph_clk_enable(ATMEL_ID_PIOC); + at91_periph_clk_enable(ATMEL_ID_PIOD); return 0; } diff --git a/board/atmel/at91sam9rlek/led.c b/board/atmel/at91sam9rlek/led.c index fede59cd32..d593aba6e4 100644 --- a/board/atmel/at91sam9rlek/led.c +++ b/board/atmel/at91sam9rlek/led.c @@ -8,16 +8,13 @@ #include <common.h> #include <asm/arch/at91sam9rl.h> -#include <asm/arch/at91_pmc.h> +#include <asm/arch/clk.h> #include <asm/arch/gpio.h> #include <asm/io.h> void coloured_LED_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - - /* Enable clock */ - writel(ATMEL_ID_PIOD, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOD); at91_set_gpio_output(CONFIG_RED_LED, 1); at91_set_gpio_output(CONFIG_GREEN_LED, 1); diff --git a/board/atmel/at91sam9x5ek/at91sam9x5ek.c b/board/atmel/at91sam9x5ek/at91sam9x5ek.c index 833e38335a..c14df303b2 100644 --- a/board/atmel/at91sam9x5ek/at91sam9x5ek.c +++ b/board/atmel/at91sam9x5ek/at91sam9x5ek.c @@ -9,10 +9,9 @@ #include <asm/arch/at91sam9x5_matrix.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> -#include <asm/arch/gpio.h> #include <asm/arch/clk.h> +#include <asm/arch/gpio.h> #include <lcd.h> #include <atmel_hlcdc.h> #include <atmel_mci.h> @@ -39,7 +38,6 @@ static void at91sam9x5ek_nand_hw_init(void) { struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; unsigned long csa; /* Enable CS3 */ @@ -72,7 +70,7 @@ static void at91sam9x5ek_nand_hw_init(void) AT91_SMC_MODE_TDF_CYCLE(1), &smc->cs[3].mode); - writel(1 << ATMEL_ID_PIOCD, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOCD); /* Configure RDY/BSY */ at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); @@ -141,8 +139,6 @@ void lcd_disable(void) static void at91sam9x5ek_lcd_hw_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - if (has_lcdc()) { at91_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDPWM */ at91_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDVSYNC */ @@ -176,7 +172,7 @@ static void at91sam9x5ek_lcd_hw_init(void) at91_set_a_periph(AT91_PIO_PORTC, 22, 0); /* LCDD22 */ at91_set_a_periph(AT91_PIO_PORTC, 23, 0); /* LCDD23 */ - writel(1 << ATMEL_ID_LCDC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_LCDC); } } diff --git a/board/atmel/sama5d2_xplained/sama5d2_xplained.c b/board/atmel/sama5d2_xplained/sama5d2_xplained.c index 8ed01ddbea..10edf28a9b 100644 --- a/board/atmel/sama5d2_xplained/sama5d2_xplained.c +++ b/board/atmel/sama5d2_xplained/sama5d2_xplained.c @@ -15,7 +15,6 @@ #include <version.h> #include <asm/io.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/atmel_pio4.h> #include <asm/arch/atmel_mpddrc.h> #include <asm/arch/atmel_usba_udc.h> diff --git a/board/atmel/sama5d3_xplained/sama5d3_xplained.c b/board/atmel/sama5d3_xplained/sama5d3_xplained.c index 7acb8d0974..c8a5795b1d 100644 --- a/board/atmel/sama5d3_xplained/sama5d3_xplained.c +++ b/board/atmel/sama5d3_xplained/sama5d3_xplained.c @@ -184,14 +184,13 @@ static void ddr2_conf(struct atmel_mpddrc_config *ddr2) void mem_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; struct atmel_mpddrc_config ddr2; ddr2_conf(&ddr2); - /* enable MPDDR clock */ + /* Enable MPDDR clock */ at91_periph_clk_enable(ATMEL_ID_MPDDRC); - writel(AT91_PMC_DDR, &pmc->scer); + at91_system_clk_enable(AT91_PMC_DDR); /* DDRAM2 Controller initialize */ ddr2_init(ATMEL_BASE_MPDDRC, ATMEL_BASE_DDRCS, &ddr2); diff --git a/board/atmel/sama5d3xek/sama5d3xek.c b/board/atmel/sama5d3xek/sama5d3xek.c index 0d824fc0ba..8576560ee5 100644 --- a/board/atmel/sama5d3xek/sama5d3xek.c +++ b/board/atmel/sama5d3xek/sama5d3xek.c @@ -443,14 +443,13 @@ static void ddr2_conf(struct atmel_mpddrc_config *ddr2) void mem_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; struct atmel_mpddrc_config ddr2; ddr2_conf(&ddr2); - /* enable MPDDR clock */ + /* Enable MPDDR clock */ at91_periph_clk_enable(ATMEL_ID_MPDDRC); - writel(AT91_PMC_DDR, &pmc->scer); + at91_system_clk_enable(AT91_PMC_DDR); /* DDRAM2 Controller initialize */ ddr2_init(ATMEL_BASE_MPDDRC, ATMEL_BASE_DDRCS, &ddr2); diff --git a/board/atmel/sama5d4_xplained/sama5d4_xplained.c b/board/atmel/sama5d4_xplained/sama5d4_xplained.c index e2f33a3e8b..e154aa9322 100644 --- a/board/atmel/sama5d4_xplained/sama5d4_xplained.c +++ b/board/atmel/sama5d4_xplained/sama5d4_xplained.c @@ -383,14 +383,13 @@ static void ddr2_conf(struct atmel_mpddrc_config *ddr2) void mem_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; struct atmel_mpddrc_config ddr2; ddr2_conf(&ddr2); - /* enable MPDDR clock */ + /* Enable MPDDR clock */ at91_periph_clk_enable(ATMEL_ID_MPDDRC); - writel(AT91_PMC_DDR, &pmc->scer); + at91_system_clk_enable(AT91_PMC_DDR); /* DDRAM2 Controller initialize */ ddr2_init(ATMEL_BASE_MPDDRC, ATMEL_BASE_DDRCS, &ddr2); diff --git a/board/atmel/sama5d4ek/sama5d4ek.c b/board/atmel/sama5d4ek/sama5d4ek.c index 1799059f87..f174cf5ba4 100644 --- a/board/atmel/sama5d4ek/sama5d4ek.c +++ b/board/atmel/sama5d4ek/sama5d4ek.c @@ -379,14 +379,13 @@ static void ddr2_conf(struct atmel_mpddrc_config *ddr2) void mem_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; struct atmel_mpddrc_config ddr2; ddr2_conf(&ddr2); - /* enable MPDDR clock */ + /* Enable MPDDR clock */ at91_periph_clk_enable(ATMEL_ID_MPDDRC); - writel(AT91_PMC_DDR, &pmc->scer); + at91_system_clk_enable(AT91_PMC_DDR); /* DDRAM2 Controller initialize */ ddr2_init(ATMEL_BASE_MPDDRC, ATMEL_BASE_DDRCS, &ddr2); diff --git a/board/bluewater/snapper9260/snapper9260.c b/board/bluewater/snapper9260/snapper9260.c index 95633b0d2e..2d1a89e102 100644 --- a/board/bluewater/snapper9260/snapper9260.c +++ b/board/bluewater/snapper9260/snapper9260.c @@ -15,7 +15,7 @@ #include <asm/arch/at91sam9260_matrix.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> +#include <asm/arch/clk.h> #include <asm/arch/gpio.h> #include <asm/arch/atmel_serial.h> #include <net.h> @@ -31,11 +31,9 @@ DECLARE_GLOBAL_DATA_PTR; static void macb_hw_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA; - /* Enable clock */ - writel(1 << ATMEL_ID_EMAC0, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_EMAC0); /* Disable pull-ups to prevent PHY going into test mode */ writel(pin_to_mask(AT91_PIN_PA14) | @@ -108,12 +106,9 @@ static void nand_hw_init(void) int board_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - - /* Enable PIO clocks */ - writel((1 << ATMEL_ID_PIOA) | - (1 << ATMEL_ID_PIOB) | - (1 << ATMEL_ID_PIOC), &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOA); + at91_periph_clk_enable(ATMEL_ID_PIOB); + at91_periph_clk_enable(ATMEL_ID_PIOC); /* The mach-type is the same for both Snapper 9260 and 9G20 */ gd->bd->bi_arch_number = MACH_TYPE_SNAPPER_9260; diff --git a/board/calao/usb_a9263/usb_a9263.c b/board/calao/usb_a9263/usb_a9263.c index 266e9507ef..d627b240d0 100644 --- a/board/calao/usb_a9263/usb_a9263.c +++ b/board/calao/usb_a9263/usb_a9263.c @@ -12,7 +12,7 @@ #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> #include <asm/arch/at91_matrix.h> -#include <asm/arch/at91_pmc.h> +#include <asm/arch/clk.h> #include <asm/arch/gpio.h> #include <asm-generic/gpio.h> #include <asm/io.h> @@ -43,7 +43,6 @@ static void usb_a9263_nand_hw_init(void) unsigned long csa; at91_smc_t *smc = (at91_smc_t *)ATMEL_BASE_SMC0; at91_matrix_t *matrix = (at91_matrix_t *)ATMEL_BASE_MATRIX; - at91_pmc_t *pmc = (at91_pmc_t *)ATMEL_BASE_PMC; /* Enable CS3 */ csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A; @@ -66,7 +65,8 @@ static void usb_a9263_nand_hw_init(void) AT91_SMC_MODE_DBW_8 | AT91_SMC_MODE_TDF_CYCLE(2), &smc->cs[3].mode); - writel(1 << ATMEL_ID_PIOA | 1 << ATMEL_ID_PIOCDE, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOA); + at91_periph_clk_enable(ATMEL_ID_PIOCDE); /* Configure RDY/BSY */ gpio_request(CONFIG_SYS_NAND_READY_PIN, "NAND ready/busy"); @@ -81,10 +81,7 @@ static void usb_a9263_nand_hw_init(void) #ifdef CONFIG_MACB static void usb_a9263_macb_hw_init(void) { - at91_pmc_t *pmc = (at91_pmc_t *)ATMEL_BASE_PMC; - - /* Enable clock */ - writel(1 << ATMEL_ID_EMAC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_EMAC); /* * Disable pull-up on: diff --git a/board/egnite/ethernut5/ethernut5.c b/board/egnite/ethernut5/ethernut5.c index 67d39844ac..2c8e978eb3 100644 --- a/board/egnite/ethernut5/ethernut5.c +++ b/board/egnite/ethernut5/ethernut5.c @@ -67,8 +67,8 @@ #include <asm/arch/at91sam9260_matrix.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/at91_spi.h> +#include <asm/arch/clk.h> #include <asm/arch/gpio.h> #include <asm/io.h> #include <asm/gpio.h> @@ -151,12 +151,10 @@ static void ethernut5_nand_hw_init(void) */ int board_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + at91_periph_clk_enable(ATMEL_ID_PIOA); + at91_periph_clk_enable(ATMEL_ID_PIOB); + at91_periph_clk_enable(ATMEL_ID_PIOC); - /* Enable clocks for all PIOs */ - writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) | - (1 << ATMEL_ID_PIOC), - &pmc->pcer); /* Set adress of boot parameters. */ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; /* Initialize UARTs and power management. */ @@ -179,10 +177,9 @@ int board_eth_init(bd_t *bis) { const char *devname; unsigned short mode; - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - /* Enable on-chip EMAC clock. */ - writel(1 << ATMEL_ID_EMAC0, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_EMAC0); + /* Need to reset PHY via power management. */ ethernut5_phy_reset(); /* Set peripheral pins. */ @@ -211,10 +208,8 @@ int board_eth_init(bd_t *bis) #ifdef CONFIG_GENERIC_ATMEL_MCI int board_mmc_init(bd_t *bd) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + at91_periph_clk_enable(ATMEL_ID_MCI); - /* Enable MCI clock. */ - writel(1 << ATMEL_ID_MCI, &pmc->pcer); /* Initialize MCI hardware. */ at91_mci_hw_init(); /* Register the device. */ @@ -229,6 +224,7 @@ int board_mmc_getcd(struct mmc *mmc) #ifdef CONFIG_ATMEL_SPI /* + * Note, that u-boot uses different code for SPI bus access. While * memory routines use automatic chip select control, the serial * flash support requires 'manual' GPIO control. Thus, we switch diff --git a/board/esd/meesc/meesc.c b/board/esd/meesc/meesc.c index b7f9f90cde..fe781dcc92 100644 --- a/board/esd/meesc/meesc.c +++ b/board/esd/meesc/meesc.c @@ -87,9 +87,8 @@ static void meesc_nand_hw_init(void) #ifdef CONFIG_MACB static void meesc_macb_hw_init(void) { - at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; - /* Enable clock */ - writel(1 << ATMEL_ID_EMAC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_EMAC); + at91_macb_hw_init(); } #endif @@ -244,12 +243,10 @@ int misc_init_r(void) int board_early_init_f(void) { - at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; - - /* enable all clocks */ - writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) | - (1 << ATMEL_ID_PIOCDE) | (1 << ATMEL_ID_UHP), - &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOA); + at91_periph_clk_enable(ATMEL_ID_PIOB); + at91_periph_clk_enable(ATMEL_ID_PIOCDE); + at91_periph_clk_enable(ATMEL_ID_UHP); at91_seriald_hw_init(); diff --git a/board/mini-box/picosam9g45/led.c b/board/mini-box/picosam9g45/led.c index dc1013ad12..3fb6a7b7cd 100644 --- a/board/mini-box/picosam9g45/led.c +++ b/board/mini-box/picosam9g45/led.c @@ -9,15 +9,12 @@ #include <common.h> #include <asm/io.h> #include <asm/arch/at91sam9g45.h> -#include <asm/arch/at91_pmc.h> +#include <asm/arch/clk.h> #include <asm/arch/gpio.h> void coloured_LED_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - - /* Enable clock */ - writel(1 << ATMEL_ID_PIODE, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIODE); at91_set_gpio_output(CONFIG_GREEN_LED, 1); diff --git a/board/mini-box/picosam9g45/picosam9g45.c b/board/mini-box/picosam9g45/picosam9g45.c index 193f14d75a..32ba9c6225 100644 --- a/board/mini-box/picosam9g45/picosam9g45.c +++ b/board/mini-box/picosam9g45/picosam9g45.c @@ -17,7 +17,6 @@ #include <asm/arch/at91sam9g45_matrix.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/gpio.h> #include <asm/arch/clk.h> #include <lcd.h> @@ -80,15 +79,13 @@ static void ddr2_conf(struct atmel_mpddrc_config *ddr2) void mem_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; struct at91_matrix *mat = (struct at91_matrix *)ATMEL_BASE_MATRIX; struct atmel_mpddrc_config ddr2; unsigned long csa; ddr2_conf(&ddr2); - /* enable DDR2 clock */ - writel(AT91_PMC_DDR, &pmc->scer); + at91_system_clk_enable(AT91_PMC_DDR); /* Chip select 1 is for DDR2/SDRAM */ csa = readl(&mat->ebicsa); @@ -105,9 +102,7 @@ void mem_init(void) #ifdef CONFIG_CMD_USB static void picosam9g45_usb_hw_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - - writel(1 << ATMEL_ID_PIODE, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIODE); at91_set_gpio_output(AT91_PIN_PD1, 0); at91_set_gpio_output(AT91_PIN_PD3, 0); @@ -117,11 +112,9 @@ static void picosam9g45_usb_hw_init(void) #ifdef CONFIG_MACB static void picosam9g45_macb_hw_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA; - /* Enable clock */ - writel(1 << ATMEL_ID_EMAC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_EMAC); /* * Disable pull-up on: @@ -181,8 +174,6 @@ void lcd_disable(void) static void picosam9g45_lcd_hw_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - at91_set_A_periph(AT91_PIN_PE0, 0); /* LCDDPWR */ at91_set_A_periph(AT91_PIN_PE2, 0); /* LCDCC */ at91_set_A_periph(AT91_PIN_PE3, 0); /* LCDVSYNC */ @@ -214,7 +205,7 @@ static void picosam9g45_lcd_hw_init(void) at91_set_A_periph(AT91_PIN_PE29, 0); /* LCDD22 */ at91_set_A_periph(AT91_PIN_PE30, 0); /* LCDD23 */ - writel(1 << ATMEL_ID_LCDC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_LCDC); gd->fb_base = CONFIG_AT91SAM9G45_LCD_BASE; } diff --git a/board/ronetix/pm9261/led.c b/board/ronetix/pm9261/led.c index cc4c2a072b..53e353a75d 100644 --- a/board/ronetix/pm9261/led.c +++ b/board/ronetix/pm9261/led.c @@ -9,15 +9,12 @@ #include <common.h> #include <asm/gpio.h> -#include <asm/arch/at91_pmc.h> +#include <asm/arch/clk.h> #include <asm/arch/gpio.h> void coloured_LED_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - - /* Enable clock */ - writel(1 << ATMEL_ID_PIOC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOC); gpio_direction_output(CONFIG_RED_LED, 1); gpio_direction_output(CONFIG_GREEN_LED, 1); diff --git a/board/ronetix/pm9261/pm9261.c b/board/ronetix/pm9261/pm9261.c index b96f745773..3cc01cb687 100644 --- a/board/ronetix/pm9261/pm9261.c +++ b/board/ronetix/pm9261/pm9261.c @@ -14,7 +14,6 @@ #include <asm/gpio.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> #include <asm/arch/at91_matrix.h> #include <asm/arch/clk.h> @@ -41,7 +40,6 @@ static void pm9261_nand_hw_init(void) unsigned long csa; struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; /* Enable CS3 */ csa = readl(&matrix->csa) | AT91_MATRIX_CSA_EBI_CS3A; @@ -69,9 +67,8 @@ static void pm9261_nand_hw_init(void) AT91_SMC_MODE_TDF_CYCLE(2), &smc->cs[3].mode); - writel(1 << ATMEL_ID_PIOA | - 1 << ATMEL_ID_PIOC, - &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOA); + at91_periph_clk_enable(ATMEL_ID_PIOC); /* Configure RDY/BSY */ gpio_direction_input(CONFIG_SYS_NAND_READY_PIN); @@ -89,7 +86,6 @@ static void pm9261_nand_hw_init(void) static void pm9261_dm9000_hw_init(void) { struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; /* Configure SMC CS2 for DM9000 */ writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) | @@ -110,7 +106,7 @@ static void pm9261_dm9000_hw_init(void) &smc->cs[2].mode); /* Configure Interrupt pin as input, no pull-up */ - writel(1 << ATMEL_ID_PIOA, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOA); at91_set_pio_input(AT91_PIO_PORTA, 24, 0); } #endif @@ -145,8 +141,6 @@ void lcd_disable(void) static void pm9261_lcd_hw_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - at91_set_a_periph(AT91_PIO_PORTB, 1, 0); /* LCDHSYNC */ at91_set_a_periph(AT91_PIO_PORTB, 2, 0); /* LCDDOTCK */ at91_set_a_periph(AT91_PIO_PORTB, 3, 0); /* LCDDEN */ @@ -170,7 +164,7 @@ static void pm9261_lcd_hw_init(void) at91_set_b_periph(AT91_PIO_PORTB, 27, 0); /* LCDD22 */ at91_set_b_periph(AT91_PIO_PORTB, 28, 0); /* LCDD23 */ - writel(1 << 17, &pmc->scer); /* LCD controller Clock, AT91SAM9261 only */ + at91_system_clk_enable(AT91_PMC_HCK1); gd->fb_base = ATMEL_BASE_SRAM; } @@ -224,12 +218,8 @@ void lcd_show_board_info(void) int board_early_init_f(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - - /* Enable clocks for some PIOs */ - writel(1 << ATMEL_ID_PIOA | - 1 << ATMEL_ID_PIOC, - &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOA); + at91_periph_clk_enable(ATMEL_ID_PIOC); at91_seriald_hw_init(); diff --git a/board/ronetix/pm9263/led.c b/board/ronetix/pm9263/led.c index bfc2310b0e..8025a20a6a 100644 --- a/board/ronetix/pm9263/led.c +++ b/board/ronetix/pm9263/led.c @@ -9,15 +9,12 @@ #include <common.h> #include <asm/gpio.h> -#include <asm/arch/at91_pmc.h> +#include <asm/arch/clk.h> #include <asm/arch/gpio.h> void coloured_LED_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - - /* Enable clock */ - writel(1 << ATMEL_ID_PIOB, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOB); gpio_direction_output(CONFIG_RED_LED, 1); gpio_direction_output(CONFIG_GREEN_LED, 1); diff --git a/board/ronetix/pm9263/pm9263.c b/board/ronetix/pm9263/pm9263.c index 1b00f08835..276ff80943 100644 --- a/board/ronetix/pm9263/pm9263.c +++ b/board/ronetix/pm9263/pm9263.c @@ -14,7 +14,6 @@ #include <asm/gpio.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> #include <asm/arch/at91_matrix.h> #include <asm/arch/clk.h> @@ -78,8 +77,6 @@ static void pm9263_nand_hw_init(void) #ifdef CONFIG_MACB static void pm9263_macb_hw_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - /* * PB27 enables the 50MHz oscillator for Ethernet PHY * 1 - enable @@ -88,8 +85,7 @@ static void pm9263_macb_hw_init(void) at91_set_pio_output(AT91_PIO_PORTB, 27, 1); at91_set_pio_value(AT91_PIO_PORTB, 27, 1); /* 1- enable, 0 - disable */ - /* Enable clock */ - writel(1 << ATMEL_ID_EMAC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_EMAC); /* * Disable pull-up on: @@ -231,8 +227,6 @@ static int pm9263_lcd_hw_psram_init(void) static void pm9263_lcd_hw_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - at91_set_a_periph(AT91_PIO_PORTC, 0, 0); /* LCDVSYNC */ at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* LCDHSYNC */ at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* LCDDOTCK */ @@ -257,7 +251,7 @@ static void pm9263_lcd_hw_init(void) at91_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDD22 */ at91_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDD23 */ - writel(1 << ATMEL_ID_LCDC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_LCDC); /* Power Control */ at91_set_pio_output(AT91_PIO_PORTA, 22, 1); @@ -323,12 +317,9 @@ void lcd_show_board_info(void) int board_early_init_f(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - - /* Enable clocks for all PIOs */ - writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) | - (1 << ATMEL_ID_PIOCDE), - &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOA); + at91_periph_clk_enable(ATMEL_ID_PIOB); + at91_periph_clk_enable(ATMEL_ID_PIOCDE); at91_seriald_hw_init(); diff --git a/board/ronetix/pm9g45/pm9g45.c b/board/ronetix/pm9g45/pm9g45.c index efc4133bbf..c2707e0015 100644 --- a/board/ronetix/pm9g45/pm9g45.c +++ b/board/ronetix/pm9g45/pm9g45.c @@ -17,7 +17,6 @@ #include <asm/gpio.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> #include <asm/arch/at91_matrix.h> #include <asm/arch/gpio.h> @@ -39,7 +38,6 @@ static void pm9g45_nand_hw_init(void) unsigned long csa; struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; /* Enable CS3 */ csa = readl(&matrix->ccr[6]) | AT91_MATRIX_CSA_EBI_CS3A; @@ -63,7 +61,7 @@ static void pm9g45_nand_hw_init(void) AT91_SMC_MODE_TDF_CYCLE(3), &smc->cs[3].mode); - writel(1 << ATMEL_ID_PIOC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOC); #ifdef CONFIG_SYS_NAND_READY_PIN /* Configure RDY/BSY */ @@ -78,8 +76,6 @@ static void pm9g45_nand_hw_init(void) #ifdef CONFIG_MACB static void pm9g45_macb_hw_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - /* * PD2 enables the 50MHz oscillator for Ethernet PHY * 1 - enable @@ -88,8 +84,7 @@ static void pm9g45_macb_hw_init(void) at91_set_pio_output(AT91_PIO_PORTD, 2, 1); at91_set_pio_value(AT91_PIO_PORTD, 2, 1); /* 1- enable, 0 - disable */ - /* Enable clock */ - writel(1 << ATMEL_ID_EMAC, &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_EMAC); /* * Disable pull-up on: @@ -114,13 +109,10 @@ static void pm9g45_macb_hw_init(void) int board_early_init_f(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; - - /* Enable clocks for all PIOs */ - writel((1 << ATMEL_ID_PIOA) | - (1 << ATMEL_ID_PIOB) | - (1 << ATMEL_ID_PIOC) | - (1 << ATMEL_ID_PIODE), &pmc->pcer); + at91_periph_clk_enable(ATMEL_ID_PIOA); + at91_periph_clk_enable(ATMEL_ID_PIOB); + at91_periph_clk_enable(ATMEL_ID_PIOC); + at91_periph_clk_enable(ATMEL_ID_PIODE); at91_seriald_hw_init(); diff --git a/board/siemens/corvus/board.c b/board/siemens/corvus/board.c index 38c0ca3aae..ba70819347 100644 --- a/board/siemens/corvus/board.c +++ b/board/siemens/corvus/board.c @@ -17,7 +17,6 @@ #include <asm/arch/at91sam9g45_matrix.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> #include <asm/arch/gpio.h> #include <asm/arch/clk.h> @@ -147,13 +146,11 @@ static void ddr2_conf(struct atmel_mpddrc_config *ddr2) void mem_init(void) { - struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; struct atmel_mpddrc_config ddr2; ddr2_conf(&ddr2); - /* enable DDR2 clock */ - writel(AT91_PMC_DDR, &pmc->scer); + at91_system_clk_enable(AT91_PMC_DDR); /* DDRAM2 Controller initialize */ ddr2_init(ATMEL_BASE_DDRSDRC0, ATMEL_BASE_CS6, &ddr2); @@ -214,6 +211,7 @@ void at91_udp_hw_init(void) /* Enable UPLL clock */ writel(AT91_PMC_UPLLEN | AT91_PMC_BIASEN, &pmc->uckr); + /* Enable UDPHS clock */ at91_periph_clk_enable(ATMEL_ID_UDPHS); } diff --git a/board/siemens/smartweb/smartweb.c b/board/siemens/smartweb/smartweb.c index d82f1b73a7..e7ee65cd8d 100644 --- a/board/siemens/smartweb/smartweb.c +++ b/board/siemens/smartweb/smartweb.c @@ -22,7 +22,6 @@ #include <asm/arch/at91sam9260_matrix.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/at91_spi.h> #include <spi.h> #include <asm/arch/clk.h> @@ -126,7 +125,7 @@ void at91_udp_hw_init(void) /* Enable UDPCK clock, MCK is enabled in at91_clock_init() */ at91_periph_clk_enable(ATMEL_ID_UDP); - writel(AT91SAM926x_PMC_UDP, &pmc->scer); + at91_system_clk_enable(AT91SAM926x_PMC_UDP); } struct at91_udc_data board_udc_data = { diff --git a/board/siemens/taurus/taurus.c b/board/siemens/taurus/taurus.c index 72c5e6083d..9374064df5 100644 --- a/board/siemens/taurus/taurus.c +++ b/board/siemens/taurus/taurus.c @@ -18,7 +18,6 @@ #include <asm/arch/at91sam9260_matrix.h> #include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_common.h> -#include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> #include <asm/arch/gpio.h> #include <asm/arch/at91sam9_sdramc.h> @@ -300,7 +299,7 @@ void at91_udp_hw_init(void) /* Enable UDPCK clock, MCK is enabled in at91_clock_init() */ at91_periph_clk_enable(ATMEL_ID_UDP); - writel(AT91SAM926x_PMC_UDP, &pmc->scer); + at91_system_clk_enable(AT91SAM926x_PMC_UDP); } struct at91_udc_data board_udc_data = { |