board/freescale: Remove p1023rdb board support

Remove NXP powerpc p1023rdb board support as it is no
longer maintained.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

1 files changed, 0 insertions, 338 deletions

diff --git a/include/configs/P1023RDB.h b/include/configs/P1023RDB.h
deleted file mode 100644
index 5c29a4f274..0000000000
--- a/include/configs/P1023RDB.h
+++ /dev/null
@@ -1,338 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2013 Freescale Semiconductor, Inc.
- *
- * Authors:  Roy Zang <tie-fei.zang@freescale.com>
- *	     Chunhe Lan <Chunhe.Lan@freescale.com>
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <linux/stringify.h>
-
-#ifndef CONFIG_SYS_MONITOR_BASE
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-#endif
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
-#endif
-
-/* High Level Configuration Options */
-
-#define CONFIG_PCI_INDIRECT_BRIDGE     /* indirect PCI bridge support */
-#define CONFIG_PCIE1		/* PCIE controller 1 (slot 1) */
-#define CONFIG_PCIE2		/* PCIE controller 2 (slot 2) */
-#define CONFIG_PCIE3		/* PCIE controller 3 (slot 3) */
-#define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
-#define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_clock_freq(void);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ	66666666
-#define CONFIG_DDR_CLK_FREQ	CONFIG_SYS_CLK_FREQ
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE			/* toggle L2 cache */
-#define CONFIG_BTB			/* toggle branch predition */
-#define CONFIG_HWCONFIG
-
-#define CONFIG_ENABLE_36BIT_PHYS
-
-/* Implement conversion of addresses in the LBC */
-#define CONFIG_SYS_LBC_LBCR		0x00000000
-#define CONFIG_SYS_LBC_LCRR		LCRR_CLKDIV_8
-
-/* DDR Setup */
-#define CONFIG_VERY_BIG_RAM
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	1
-
-#define CONFIG_DDR_SPD
-#define CONFIG_SYS_SDRAM_SIZE		512u	/* DDR is 512M */
-#define CONFIG_SYS_SPD_BUS_NUM          0
-#define SPD_EEPROM_ADDRESS              0x50
-#define CONFIG_SYS_DDR_RAW_TIMING
-
-/*
- * Memory map
- *
- * 0x0000_0000	0x1fff_ffff	DDR			512M cacheable
- * 0x8000_0000	0xbfff_ffff	PCI Express Mem		1G non-cacheable
- * 0xc000_0000	0xdfff_ffff	PCI			512M non-cacheable
- * 0xe100_0000	0xe3ff_ffff	PCI IO range		4M non-cacheable
- * 0xff00_0000	0xff3f_ffff	DPAA_QBMAN		4M cacheable
- * 0xff60_0000	0xff7f_ffff	CCSR			2M non-cacheable
- * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K cacheable TLB0
- *
- * Localbus non-cacheable
- *
- * 0xec00_0000	0xefff_ffff	NOR flash		64M non-cacheable
- * 0xffa0_0000	0xffaf_ffff	NAND			1M non-cacheable
- */
-
-/*
- * Local Bus Definitions
- */
-#define CONFIG_SYS_FLASH_BASE		0xec000000 /* start of FLASH 64M */
-#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_FLASH_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
-				| BR_PS_16 | BR_V)
-#define CONFIG_FLASH_OR_PRELIM	0xfc000ff7
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	512	/* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000/* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-					GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN	(768 * 1024)	  /* Reserve 512 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN	(6 * 1024 * 1024) /* Reserved for malloc */
-
-#define CONFIG_SYS_NAND_BASE		0xffa00000
-#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
-
-#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_NAND_FSL_ELBC
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
-
-/* NAND flash config */
-#define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
-				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
-				| BR_PS_8		/* Port Size = 8bit */ \
-				| BR_MS_FCM		/* MSEL = FCM */ \
-				| BR_V)			/* valid */
-#define CONFIG_SYS_NAND_OR_PRELIM  (OR_AM_256KB		/* length 256K */ \
-				| OR_FCM_PGS \
-				| OR_FCM_CSCT \
-				| OR_FCM_CST \
-				| OR_FCM_CHT \
-				| OR_FCM_SCY_1 \
-				| OR_FCM_TRLX \
-				| OR_FCM_EHTR)
-
-#define CONFIG_SYS_BR0_PRELIM	CONFIG_FLASH_BR_PRELIM	/* NOR Base Address */
-#define CONFIG_SYS_OR0_PRELIM	CONFIG_FLASH_OR_PRELIM	/* NOR Options */
-#define CONFIG_SYS_BR1_PRELIM	CONFIG_SYS_NAND_BR_PRELIM
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-
-/* Serial Port */
-#undef	CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE	\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR + 0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-
-/*
- * I2C2 EEPROM
- */
-#define CONFIG_ID_EEPROM
-#ifdef CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#endif
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
-#define CONFIG_SYS_EEPROM_BUS_NUM		0
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-
-/* controller 3, Slot 1, tgtid 3, Base address b000 */
-#define CONFIG_SYS_PCIE3_NAME		"Slot 3"
-#define CONFIG_SYS_PCIE3_MEM_VIRT	0x80000000
-#define CONFIG_SYS_PCIE3_MEM_BUS	0x80000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS	0x80000000
-#define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE3_IO_VIRT	0xffc00000
-#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE3_IO_PHYS	0xffc00000
-#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 2, direct to uli, tgtid 2, Base address 9000 */
-#define CONFIG_SYS_PCIE2_NAME		"Slot 2"
-#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
-#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS	0xffc10000
-#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 1, Slot 2, tgtid 1, Base address a000 */
-#define CONFIG_SYS_PCIE1_NAME		"Slot 1"
-#define CONFIG_SYS_PCIE1_MEM_VIRT	0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_BUS	0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc20000
-#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS	0xffc20000
-#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
-
-#if defined(CONFIG_PCI)
-#define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
-#endif	/* CONFIG_PCI */
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO		/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
-
-/*
- * USB
- */
-#define CONFIG_HAS_FSL_DR_USB
-#ifdef CONFIG_HAS_FSL_DR_USB
-#ifdef CONFIG_USB_EHCI_HCD
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_USB_EHCI_FSL
-#endif
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)   /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)   /* Increase max gunzip size */
-
-/*
- * Environment Configuration
- */
-#define CONFIG_BOOTFILE		"uImage"
-#define CONFIG_UBOOTPATH	(u-boot.bin) /* U-Boot image on TFTP server */
-
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR		1000000
-
-/* Qman/Bman */
-#define CONFIG_SYS_QMAN_MEM_BASE	0xff000000
-#define CONFIG_SYS_QMAN_MEM_PHYS	CONFIG_SYS_QMAN_MEM_BASE
-#define CONFIG_SYS_QMAN_MEM_SIZE	0x00200000
-#define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
-#define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
-#define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
-#define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
-					CONFIG_SYS_QMAN_CENA_SIZE)
-#define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_QMAN_SWP_ISDR_REG	0xE08
-#define CONFIG_SYS_BMAN_MEM_BASE	0xff200000
-#define CONFIG_SYS_BMAN_MEM_PHYS	CONFIG_SYS_BMAN_MEM_BASE
-#define CONFIG_SYS_BMAN_MEM_SIZE	0x00200000
-#define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
-#define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
-#define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
-#define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
-					CONFIG_SYS_BMAN_CENA_SIZE)
-#define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_BMAN_SWP_ISDR_REG	0xE08
-
-/* For FM */
-#define CONFIG_SYS_DPAA_FMAN
-
-/* Default address of microcode for the Linux Fman driver */
-/* QE microcode/firmware address */
-#define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
-#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR	0x1
-#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR	0x2
-
-#define CONFIG_SYS_TBIPA_VALUE	8
-#define CONFIG_ETHPRIME		"FM1@DTSEC1"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS	\
-	"netdev=eth0\0"						\
-	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
-	"loadaddr=1000000\0"					\
-	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
-	"tftpflash=tftpboot $loadaddr $uboot; "			\
-		"protect off $ubootaddr +$filesize; "		\
-		"erase $ubootaddr +$filesize; "			\
-		"cp.b $loadaddr $ubootaddr $filesize; "		\
-		"protect on $ubootaddr +$filesize; "		\
-		"cmp.b $loadaddr $ubootaddr $filesize\0"	\
-	"consoledev=ttyS0\0"					\
-	"ramdiskaddr=2000000\0"					\
-	"ramdiskfile=rootfs.ext2.gz.uboot\0"			\
-	"fdtaddr=1e00000\0"					\
-	"fdtfile=p1023rdb.dtb\0"				\
-	"othbootargs=ramdisk_size=600000\0"			\
-	"bdev=sda1\0"						\
-	"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
-
-#define CONFIG_HDBOOT					\
-	"setenv bootargs root=/dev/$bdev rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $loadaddr $bootfile;"			\
-	"tftp $fdtaddr $fdtfile;"			\
-	"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_NFSBOOTCOMMAND						\
-	"setenv bootargs root=/dev/nfs rw "				\
-	"nfsroot=$serverip:$rootpath "					\
-	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
-	"console=$consoledev,$baudrate $othbootargs;"			\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND						\
-	"setenv bootargs root=/dev/ram rw "				\
-	"console=$consoledev,$baudrate $othbootargs;"			\
-	"tftp $ramdiskaddr $ramdiskfile;"				\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND		CONFIG_RAMBOOTCOMMAND
-
-#endif	/* __CONFIG_H */