Merge git://git.denx.de/u-boot-dm

26 files changed, 601 insertions, 173 deletions

diff --git a/drivers/Kconfig b/drivers/Kconfig
index 128736dae3..dcce532e2d 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -2,6 +2,8 @@ menu "Device Drivers"
 
 source "drivers/core/Kconfig"
 
+source "drivers/demo/Kconfig"
+
 source "drivers/pci/Kconfig"
 
 source "drivers/pcmcia/Kconfig"
@@ -48,4 +50,6 @@ source "drivers/dma/Kconfig"
 
 source "drivers/crypto/Kconfig"
 
+source "drivers/thermal/Kconfig"
+
 endmenu
diff --git a/drivers/core/Kconfig b/drivers/core/Kconfig
index d2799dc861..f0d611007a 100644
--- a/drivers/core/Kconfig
+++ b/drivers/core/Kconfig
@@ -2,5 +2,51 @@ config DM
 	bool "Enable Driver Model"
 	depends on !SPL_BUILD
 	help
-	  This config option enables Driver Model.
-	  To use legacy drivers, say N.
+	  This config option enables Driver Model. This brings in the core
+	  support, including scanning of platform data on start-up. If
+	  CONFIG_OF_CONTROL is enabled, the device tree will be scanned also
+	  when available.
+
+config SPL_DM
+	bool "Enable Driver Model for SPL"
+	depends on DM && SPL
+	help
+	  Enable driver model in SPL. You will need to provide a
+	  suitable malloc() implementation. If you are not using the
+	  full malloc() enabled by CONFIG_SYS_SPL_MALLOC_START,
+	  consider using CONFIG_SYS_MALLOC_SIMPLE. In that case you
+	  must provide CONFIG_SYS_MALLOC_F_LEN to set the size.
+	  In most cases driver model will only allocate a few uclasses
+	  and devices in SPL, so 1KB should be enable. See
+	  CONFIG_SYS_MALLOC_F_LEN for more details on how to enable it.
+
+config DM_WARN
+	bool "Enable warnings in driver model"
+	help
+	  The dm_warn() function can use up quite a bit of space for its
+	  strings. By default this is disabled for SPL builds to save space.
+	  This will cause dm_warn() to be compiled out - it will do nothing
+	  when called.
+	depends on DM
+	default y if !SPL_BUILD
+	default n if SPL_BUILD
+
+config DM_DEVICE_REMOVE
+	bool "Support device removal"
+	help
+	  We can save some code space by dropping support for removing a
+	  device. This is not normally required in SPL, so by default this
+	  option is disabled for SPL.
+	depends on DM
+	default y if !SPL_BUILD
+	default n if SPL_BUILD
+
+config DM_STDIO
+	bool "Support stdio registration"
+	help
+	  Normally serial drivers register with stdio so that they can be used
+	  as normal output devices. In SPL we don't normally use stdio, so
+	  we can omit this feature.
+	depends on DM
+	default y if !SPL_BUILD
+	default n if SPL_BUILD
diff --git a/drivers/core/device.c b/drivers/core/device.c
index b73d3b8961..73c3e07c28 100644
--- a/drivers/core/device.c
+++ b/drivers/core/device.c
@@ -449,3 +449,15 @@ enum uclass_id device_get_uclass_id(struct udevice *dev)
 {
 	return dev->uclass->uc_drv->id;
 }
+
+#ifdef CONFIG_OF_CONTROL
+fdt_addr_t dev_get_addr(struct udevice *dev)
+{
+	return fdtdec_get_addr(gd->fdt_blob, dev->of_offset, "reg");
+}
+#else
+fdt_addr_t dev_get_addr(struct udevice *dev)
+{
+	return FDT_ADDR_T_NONE;
+}
+#endif
diff --git a/drivers/core/root.c b/drivers/core/root.c
index 73e3c7228e..9b5c6bb10c 100644
--- a/drivers/core/root.c
+++ b/drivers/core/root.c
@@ -37,6 +37,65 @@ struct udevice *dm_root(void)
 	return gd->dm_root;
 }
 
+#if defined(CONFIG_NEEDS_MANUAL_RELOC)
+void fix_drivers(void)
+{
+	struct driver *drv =
+		ll_entry_start(struct driver, driver);
+	const int n_ents = ll_entry_count(struct driver, driver);
+	struct driver *entry;
+
+	for (entry = drv; entry != drv + n_ents; entry++) {
+		if (entry->of_match)
+			entry->of_match = (const struct udevice_id *)
+				((u32)entry->of_match + gd->reloc_off);
+		if (entry->bind)
+			entry->bind += gd->reloc_off;
+		if (entry->probe)
+			entry->probe += gd->reloc_off;
+		if (entry->remove)
+			entry->remove += gd->reloc_off;
+		if (entry->unbind)
+			entry->unbind += gd->reloc_off;
+		if (entry->ofdata_to_platdata)
+			entry->ofdata_to_platdata += gd->reloc_off;
+		if (entry->child_pre_probe)
+			entry->child_pre_probe += gd->reloc_off;
+		if (entry->child_post_remove)
+			entry->child_post_remove += gd->reloc_off;
+		/* OPS are fixed in every uclass post_probe function */
+		if (entry->ops)
+			entry->ops += gd->reloc_off;
+	}
+}
+
+void fix_uclass(void)
+{
+	struct uclass_driver *uclass =
+		ll_entry_start(struct uclass_driver, uclass);
+	const int n_ents = ll_entry_count(struct uclass_driver, uclass);
+	struct uclass_driver *entry;
+
+	for (entry = uclass; entry != uclass + n_ents; entry++) {
+		if (entry->post_bind)
+			entry->post_bind += gd->reloc_off;
+		if (entry->pre_unbind)
+			entry->pre_unbind += gd->reloc_off;
+		if (entry->post_probe)
+			entry->post_probe += gd->reloc_off;
+		if (entry->pre_remove)
+			entry->pre_remove += gd->reloc_off;
+		if (entry->init)
+			entry->init += gd->reloc_off;
+		if (entry->destroy)
+			entry->destroy += gd->reloc_off;
+		/* FIXME maybe also need to fix these ops */
+		if (entry->ops)
+			entry->ops += gd->reloc_off;
+	}
+}
+#endif
+
 int dm_init(void)
 {
 	int ret;
@@ -47,6 +106,11 @@ int dm_init(void)
 	}
 	INIT_LIST_HEAD(&DM_UCLASS_ROOT_NON_CONST);
 
+#if defined(CONFIG_NEEDS_MANUAL_RELOC)
+	fix_drivers();
+	fix_uclass();
+#endif
+
 	ret = device_bind_by_name(NULL, false, &root_info, &DM_ROOT_NON_CONST);
 	if (ret)
 		return ret;
diff --git a/drivers/demo/Kconfig b/drivers/demo/Kconfig
new file mode 100644
index 0000000000..7a8ce18555
--- /dev/null
+++ b/drivers/demo/Kconfig
@@ -0,0 +1,26 @@
+config DM_DEMO
+	bool "Enable demo uclass support"
+	depends on DM
+	help
+	  This uclass allows you to play around with driver model. It provides
+	  an interface to a couple of demo devices. You can access it using
+	  the 'demo' command or by calling the uclass functions from your
+	  own code.
+
+config DM_DEMO_SIMPLE
+	bool "Enable simple demo device for driver model"
+	depends on DM_DEMO
+	help
+	  This device allows you to play around with driver model. It prints
+	  a message when the 'demo hello' command is executed which targets
+	  this device. It can be used to help understand how driver model
+	  works.
+
+config DM_DEMO_SHAPE
+	bool "Enable shape demo device for driver model"
+	depends on DM_DEMO
+	help
+	  This device allows you to play around with driver model. It prints
+	  a shape when the 'demo hello' command is executed which targets
+	  this device. It can be used to help understand how driver model
+	  works.
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index d21302f8da..b609e73bba 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -2,5 +2,8 @@ config DM_GPIO
 	bool "Enable Driver Model for GPIO drivers"
 	depends on DM
 	help
-	  If you want to use driver model for GPIO drivers, say Y.
-	  To use legacy GPIO drivers, say N.
+	  Enable driver model for GPIO access. The standard GPIO
+	  interface (gpio_get_value(), etc.) is then implemented by
+	  the GPIO uclass. Drivers provide methods to query the
+	  particular GPIOs that they provide. The uclass interface
+	  is defined in include/asm-generic/gpio.h.
diff --git a/drivers/gpio/at91_gpio.c b/drivers/gpio/at91_gpio.c
index 6129c020ea..22fbd63098 100644
--- a/drivers/gpio/at91_gpio.c
+++ b/drivers/gpio/at91_gpio.c
@@ -451,7 +451,7 @@ struct at91_port_priv {
 /* set GPIO pin 'gpio' as an input */
 static int at91_gpio_direction_input(struct udevice *dev, unsigned offset)
 {
-	struct at91_port_priv *port = dev_get_platdata(dev);
+	struct at91_port_priv *port = dev_get_priv(dev);
 
 	at91_set_port_input(port->regs, offset, 0);
 
@@ -462,7 +462,7 @@ static int at91_gpio_direction_input(struct udevice *dev, unsigned offset)
 static int at91_gpio_direction_output(struct udevice *dev, unsigned offset,
 				       int value)
 {
-	struct at91_port_priv *port = dev_get_platdata(dev);
+	struct at91_port_priv *port = dev_get_priv(dev);
 
 	at91_set_port_output(port->regs, offset, value);
 
@@ -472,7 +472,7 @@ static int at91_gpio_direction_output(struct udevice *dev, unsigned offset,
 /* read GPIO IN value of pin 'gpio' */
 static int at91_gpio_get_value(struct udevice *dev, unsigned offset)
 {
-	struct at91_port_priv *port = dev_get_platdata(dev);
+	struct at91_port_priv *port = dev_get_priv(dev);
 
 	return at91_get_port_value(port->regs, offset);
 }
@@ -481,7 +481,7 @@ static int at91_gpio_get_value(struct udevice *dev, unsigned offset)
 static int at91_gpio_set_value(struct udevice *dev, unsigned offset,
 			       int value)
 {
-	struct at91_port_priv *port = dev_get_platdata(dev);
+	struct at91_port_priv *port = dev_get_priv(dev);
 
 	at91_set_port_value(port->regs, offset, value);
 
@@ -490,7 +490,7 @@ static int at91_gpio_set_value(struct udevice *dev, unsigned offset,
 
 static int at91_gpio_get_function(struct udevice *dev, unsigned offset)
 {
-	struct at91_port_priv *port = dev_get_platdata(dev);
+	struct at91_port_priv *port = dev_get_priv(dev);
 
 	/* GPIOF_FUNC is not implemented yet */
 	if (at91_get_port_output(port->regs, offset))
diff --git a/drivers/gpio/mxc_gpio.c b/drivers/gpio/mxc_gpio.c
index 8bb9e39b72..815407bb03 100644
--- a/drivers/gpio/mxc_gpio.c
+++ b/drivers/gpio/mxc_gpio.c
@@ -23,6 +23,7 @@ enum mxc_gpio_direction {
 #define GPIO_PER_BANK			32
 
 struct mxc_gpio_plat {
+	int bank_index;
 	struct gpio_regs *regs;
 };
 
@@ -150,6 +151,9 @@ int gpio_direction_output(unsigned gpio, int value)
 #endif
 
 #ifdef CONFIG_DM_GPIO
+#include <fdtdec.h>
+DECLARE_GLOBAL_DATA_PTR;
+
 static int mxc_gpio_is_output(struct gpio_regs *regs, int offset)
 {
 	u32 val;
@@ -258,23 +262,6 @@ static const struct dm_gpio_ops gpio_mxc_ops = {
 	.get_function		= mxc_gpio_get_function,
 };
 
-static const struct mxc_gpio_plat mxc_plat[] = {
-	{ (struct gpio_regs *)GPIO1_BASE_ADDR },
-	{ (struct gpio_regs *)GPIO2_BASE_ADDR },
-	{ (struct gpio_regs *)GPIO3_BASE_ADDR },
-#if defined(CONFIG_MX25) || defined(CONFIG_MX27) || defined(CONFIG_MX51) || \
-		defined(CONFIG_MX53) || defined(CONFIG_MX6)
-	{ (struct gpio_regs *)GPIO4_BASE_ADDR },
-#endif
-#if defined(CONFIG_MX27) || defined(CONFIG_MX53) || defined(CONFIG_MX6)
-	{ (struct gpio_regs *)GPIO5_BASE_ADDR },
-	{ (struct gpio_regs *)GPIO6_BASE_ADDR },
-#endif
-#if defined(CONFIG_MX53) || defined(CONFIG_MX6)
-	{ (struct gpio_regs *)GPIO7_BASE_ADDR },
-#endif
-};
-
 static int mxc_gpio_probe(struct udevice *dev)
 {
 	struct mxc_bank_info *bank = dev_get_priv(dev);
@@ -283,7 +270,7 @@ static int mxc_gpio_probe(struct udevice *dev)
 	int banknum;
 	char name[18], *str;
 
-	banknum = plat - mxc_plat;
+	banknum = plat->bank_index;
 	sprintf(name, "GPIO%d_", banknum + 1);
 	str = strdup(name);
 	if (!str)
@@ -295,12 +282,72 @@ static int mxc_gpio_probe(struct udevice *dev)
 	return 0;
 }
 
+static int mxc_gpio_bind(struct udevice *dev)
+{
+	struct mxc_gpio_plat *plat = dev->platdata;
+	fdt_addr_t addr;
+
+	/*
+	 * If platdata already exsits, directly return.
+	 * Actually only when DT is not supported, platdata
+	 * is statically initialized in U_BOOT_DEVICES.Here
+	 * will return.
+	 */
+	if (plat)
+		return 0;
+
+	addr = dev_get_addr(dev);
+	if (addr == FDT_ADDR_T_NONE)
+		return -ENODEV;
+
+	/*
+	 * TODO:
+	 * When every board is converted to driver model and DT is supported,
+	 * this can be done by auto-alloc feature, but not using calloc
+	 * to alloc memory for platdata.
+	 */
+	plat = calloc(1, sizeof(*plat));
+	if (!plat)
+		return -ENOMEM;
+
+	plat->regs = (struct gpio_regs *)addr;
+	plat->bank_index = dev->req_seq;
+	dev->platdata = plat;
+
+	return 0;
+}
+
+static const struct udevice_id mxc_gpio_ids[] = {
+	{ .compatible = "fsl,imx35-gpio" },
+	{ }
+};
+
 U_BOOT_DRIVER(gpio_mxc) = {
 	.name	= "gpio_mxc",
 	.id	= UCLASS_GPIO,
 	.ops	= &gpio_mxc_ops,
 	.probe	= mxc_gpio_probe,
 	.priv_auto_alloc_size = sizeof(struct mxc_bank_info),
+	.of_match = mxc_gpio_ids,
+	.bind	= mxc_gpio_bind,
+};
+
+#ifndef CONFIG_OF_CONTROL
+static const struct mxc_gpio_plat mxc_plat[] = {
+	{ 0, (struct gpio_regs *)GPIO1_BASE_ADDR },
+	{ 1, (struct gpio_regs *)GPIO2_BASE_ADDR },
+	{ 2, (struct gpio_regs *)GPIO3_BASE_ADDR },
+#if defined(CONFIG_MX25) || defined(CONFIG_MX27) || defined(CONFIG_MX51) || \
+		defined(CONFIG_MX53) || defined(CONFIG_MX6)
+	{ 3, (struct gpio_regs *)GPIO4_BASE_ADDR },
+#endif
+#if defined(CONFIG_MX27) || defined(CONFIG_MX53) || defined(CONFIG_MX6)
+	{ 4, (struct gpio_regs *)GPIO5_BASE_ADDR },
+	{ 5, (struct gpio_regs *)GPIO6_BASE_ADDR },
+#endif
+#if defined(CONFIG_MX53) || defined(CONFIG_MX6)
+	{ 6, (struct gpio_regs *)GPIO7_BASE_ADDR },
+#endif
 };
 
 U_BOOT_DEVICES(mxc_gpios) = {
@@ -320,3 +367,4 @@ U_BOOT_DEVICES(mxc_gpios) = {
 #endif
 };
 #endif
+#endif
diff --git a/drivers/gpio/omap_gpio.c b/drivers/gpio/omap_gpio.c
index f3a7ccb51e..19fc451079 100644
--- a/drivers/gpio/omap_gpio.c
+++ b/drivers/gpio/omap_gpio.c
@@ -291,7 +291,7 @@ static int omap_gpio_get_function(struct udevice *dev, unsigned offset)
 	struct gpio_bank *bank = dev_get_priv(dev);
 
 	/* GPIOF_FUNC is not implemented yet */
-	if (_get_gpio_direction(bank->base, offset) == OMAP_GPIO_DIR_OUT)
+	if (_get_gpio_direction(bank, offset) == OMAP_GPIO_DIR_OUT)
 		return GPIOF_OUTPUT;
 	else
 		return GPIOF_INPUT;
diff --git a/drivers/i2c/Kconfig b/drivers/i2c/Kconfig
index 202ea5d679..2cc776c73f 100644
--- a/drivers/i2c/Kconfig
+++ b/drivers/i2c/Kconfig
@@ -2,8 +2,16 @@ config DM_I2C
 	bool "Enable Driver Model for I2C drivers"
 	depends on DM
 	help
-	  If you want to use driver model for I2C drivers, say Y.
-	  To use legacy I2C drivers, say N.
+	  Enable driver model for I2C. This SPI flash interface
+	  (spi_flash_probe(), spi_flash_write(), etc.) is then
+	  implemented by the SPI flash uclass. There is one standard
+	  SPI flash driver which knows how to probe most chips
+	  supported by U-Boot. The uclass interface is defined in
+	  include/spi_flash.h, but is currently fully compatible
+	  with the old interface to avoid confusion and duplication
+	  during the transition parent. SPI and SPI flash must be
+	  enabled together (it is not possible to use driver model
+	  for one and not the other).
 
 config SYS_I2C_UNIPHIER
 	bool "UniPhier I2C driver"
diff --git a/drivers/i2c/adi_i2c.c b/drivers/i2c/adi_i2c.c
index 20495b1d7f..c58f14a36e 100644
--- a/drivers/i2c/adi_i2c.c
+++ b/drivers/i2c/adi_i2c.c
@@ -63,7 +63,7 @@ struct twi_regs {
 #endif
 
 /* All transfers are described by this data structure */
-struct i2c_msg {
+struct adi_i2c_msg {
 	u8 flags;
 #define I2C_M_COMBO		0x4
 #define I2C_M_STOP		0x2
@@ -81,7 +81,7 @@ struct i2c_msg {
  * wait_for_completion - manage the actual i2c transfer
  *	@msg: the i2c msg
  */
-static int wait_for_completion(struct twi_regs *twi, struct i2c_msg *msg)
+static int wait_for_completion(struct twi_regs *twi, struct adi_i2c_msg *msg)
 {
 	u16 int_stat, ctl;
 	ulong timebase = get_timer(0);
@@ -151,7 +151,7 @@ static int i2c_transfer(struct i2c_adapter *adap, uint8_t chip, uint addr,
 		(addr >>  8),
 		(addr >> 16),
 	};
-	struct i2c_msg msg = {
+	struct adi_i2c_msg msg = {
 		.flags = flags | (len >= 0xff ? I2C_M_STOP : 0),
 		.buf   = buffer,
 		.len   = len,
diff --git a/drivers/i2c/i2c-uclass.c b/drivers/i2c/i2c-uclass.c
index eafa457845..a6991bf875 100644
--- a/drivers/i2c/i2c-uclass.c
+++ b/drivers/i2c/i2c-uclass.c
@@ -325,7 +325,7 @@ int dm_i2c_probe(struct udevice *bus, uint chip_addr, uint chip_flags,
 	return ret;
 }
 
-int i2c_set_bus_speed(struct udevice *bus, unsigned int speed)
+int dm_i2c_set_bus_speed(struct udevice *bus, unsigned int speed)
 {
 	struct dm_i2c_ops *ops = i2c_get_ops(bus);
 	struct dm_i2c_bus *i2c = bus->uclass_priv;
@@ -346,12 +346,7 @@ int i2c_set_bus_speed(struct udevice *bus, unsigned int speed)
 	return 0;
 }
 
-/*
- * i2c_get_bus_speed:
- *
- *  Returns speed of selected I2C bus in Hz
- */
-int i2c_get_bus_speed(struct udevice *bus)
+int dm_i2c_get_bus_speed(struct udevice *bus)
 {
 	struct dm_i2c_ops *ops = i2c_get_ops(bus);
 	struct dm_i2c_bus *i2c = bus->uclass_priv;
@@ -440,7 +435,7 @@ static int i2c_post_probe(struct udevice *dev)
 	i2c->speed_hz = fdtdec_get_int(gd->fdt_blob, dev->of_offset,
 				     "clock-frequency", 100000);
 
-	return i2c_set_bus_speed(dev, i2c->speed_hz);
+	return dm_i2c_set_bus_speed(dev, i2c->speed_hz);
 }
 
 static int i2c_post_bind(struct udevice *dev)
diff --git a/drivers/i2c/kona_i2c.c b/drivers/i2c/kona_i2c.c
index 5eab338cfc..9af496bbb1 100644
--- a/drivers/i2c/kona_i2c.c
+++ b/drivers/i2c/kona_i2c.c
@@ -156,7 +156,7 @@ static struct bcm_kona_i2c_dev g_i2c_devs[CONFIG_SYS_MAX_I2C_BUS] = {
 #define I2C_M_RD	0x0001	/* read data */
 #define I2C_M_NOSTART	0x4000	/* no restart between msgs */
 
-struct i2c_msg {
+struct kona_i2c_msg {
 	uint16_t addr;
 	uint16_t flags;
 	uint16_t len;
@@ -297,7 +297,7 @@ static int bcm_kona_i2c_read_fifo_single(struct bcm_kona_i2c_dev *dev,
 
 /* Read any amount of data using the RX FIFO from the i2c bus */
 static int bcm_kona_i2c_read_fifo(struct bcm_kona_i2c_dev *dev,
-				  struct i2c_msg *msg)
+				  struct kona_i2c_msg *msg)
 {
 	unsigned int bytes_to_read = MAX_RX_FIFO_SIZE;
 	unsigned int last_byte_nak = 0;
@@ -392,7 +392,7 @@ static int bcm_kona_i2c_write_fifo_single(struct bcm_kona_i2c_dev *dev,
 
 /* Write any amount of data using TX FIFO to the i2c bus */
 static int bcm_kona_i2c_write_fifo(struct bcm_kona_i2c_dev *dev,
-				   struct i2c_msg *msg)
+				   struct kona_i2c_msg *msg)
 {
 	unsigned int bytes_to_write = MAX_TX_FIFO_SIZE;
 	unsigned int bytes_written = 0;
@@ -418,7 +418,7 @@ static int bcm_kona_i2c_write_fifo(struct bcm_kona_i2c_dev *dev,
 
 /* Send i2c address */
 static int bcm_kona_i2c_do_addr(struct bcm_kona_i2c_dev *dev,
-				struct i2c_msg *msg)
+				struct kona_i2c_msg *msg)
 {
 	unsigned char addr;
 
@@ -480,9 +480,9 @@ static void bcm_kona_i2c_config_timing(struct bcm_kona_i2c_dev *dev)
 
 /* Master transfer function */
 static int bcm_kona_i2c_xfer(struct bcm_kona_i2c_dev *dev,
-			     struct i2c_msg msgs[], int num)
+			     struct kona_i2c_msg msgs[], int num)
 {
-	struct i2c_msg *pmsg;
+	struct kona_i2c_msg *pmsg;
 	int rc = 0;
 	int i;
 
@@ -635,7 +635,7 @@ static int kona_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
 			 int alen, uchar *buffer, int len)
 {
 	/* msg[0] writes the addr, msg[1] reads the data */
-	struct i2c_msg msg[2];
+	struct kona_i2c_msg msg[2];
 	unsigned char msgbuf0[64];
 	struct bcm_kona_i2c_dev *dev = kona_get_dev(adap);
 
@@ -663,7 +663,7 @@ static int kona_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
 static int kona_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
 			  int alen, uchar *buffer, int len)
 {
-	struct i2c_msg msg[1];
+	struct kona_i2c_msg msg[1];
 	unsigned char msgbuf0[64];
 	unsigned int i;
 	struct bcm_kona_i2c_dev *dev = kona_get_dev(adap);
diff --git a/drivers/i2c/mv_i2c.c b/drivers/i2c/mv_i2c.c
index dac346334d..e65cce0d8e 100644
--- a/drivers/i2c/mv_i2c.c
+++ b/drivers/i2c/mv_i2c.c
@@ -31,7 +31,7 @@
 #endif
 
 /* All transfers are described by this data structure */
-struct i2c_msg {
+struct mv_i2c_msg {
 	u8 condition;
 	u8 acknack;
 	u8 direction;
@@ -157,7 +157,7 @@ static int i2c_isr_set_cleared(unsigned long set_mask,
  *          -5: illegal parameters
  *          -6: bus is busy and couldn't be aquired
  */
-int i2c_transfer(struct i2c_msg *msg)
+int i2c_transfer(struct mv_i2c_msg *msg)
 {
 	int ret;
 
@@ -286,7 +286,7 @@ void i2c_init(int speed, int slaveaddr)
  */
 int i2c_probe(uchar chip)
 {
-	struct i2c_msg msg;
+	struct mv_i2c_msg msg;
 
 	i2c_reset();
 
@@ -322,7 +322,7 @@ int i2c_probe(uchar chip)
  */
 int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
 {
-	struct i2c_msg msg;
+	struct mv_i2c_msg msg;
 	u8 addr_bytes[3]; /* lowest...highest byte of data address */
 
 	PRINTD(("i2c_read(chip=0x%02x, addr=0x%02x, alen=0x%02x, "
@@ -410,7 +410,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
  */
 int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
 {
-	struct i2c_msg msg;
+	struct mv_i2c_msg msg;
 	u8 addr_bytes[3]; /* lowest...highest byte of data address */
 
 	PRINTD(("i2c_write(chip=0x%02x, addr=0x%02x, alen=0x%02x, "
diff --git a/drivers/i2c/s3c24x0_i2c.c b/drivers/i2c/s3c24x0_i2c.c
index 0dd1abcf80..b4ee33f7da 100644
--- a/drivers/i2c/s3c24x0_i2c.c
+++ b/drivers/i2c/s3c24x0_i2c.c
@@ -112,9 +112,9 @@
 #define I2C_START_STOP	0x20	/* START / STOP */
 #define I2C_TXRX_ENA	0x10	/* I2C Tx/Rx enable */
 
-#define I2C_TIMEOUT_MS 1000		/* 1 second */
+#define I2C_TIMEOUT_MS 10		/* 10 ms */
 
-#define	HSI2C_TIMEOUT_US 100000 /* 100 ms, finer granularity */
+#define	HSI2C_TIMEOUT_US 10000 /* 10 ms, finer granularity */
 
 
 /* To support VCMA9 boards and other who dont define max_i2c_num */
diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index e69de29bb2..813d1c24b9 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -0,0 +1,9 @@
+config DM_CROS_EC
+	bool "Enable Driver Model for Chrome OS EC"
+	depends on DM
+	help
+	  Enable driver model for the Chrome OS EC interface. This
+	  allows the cros_ec SPI driver to operate with CONFIG_DM_SPI
+	  but otherwise makes few changes. Since cros_ec also supports
+	  I2C and LPC (which don't support driver model yet), a full
+	  conversion is not yet possible.
diff --git a/drivers/mtd/Kconfig b/drivers/mtd/Kconfig
index 415ab4eba9..59278d1eef 100644
--- a/drivers/mtd/Kconfig
+++ b/drivers/mtd/Kconfig
@@ -1 +1,3 @@
 source "drivers/mtd/nand/Kconfig"
+
+source "drivers/mtd/spi/Kconfig"
diff --git a/drivers/mtd/spi/Kconfig b/drivers/mtd/spi/Kconfig
new file mode 100644
index 0000000000..2dc46b4b34
--- /dev/null
+++ b/drivers/mtd/spi/Kconfig
@@ -0,0 +1,14 @@
+config DM_SPI_FLASH
+	bool "Enable Driver Model for SPI flash"
+	depends on DM && SPI
+	help
+	  Enable driver model for SPI flash. This SPI flash interface
+	  (spi_flash_probe(), spi_flash_write(), etc.) is then
+	  implemented by the SPI flash uclass. There is one standard
+	  SPI flash driver which knows how to probe most chips
+	  supported by U-Boot. The uclass interface is defined in
+	  include/spi_flash.h, but is currently fully compatible
+	  with the old interface to avoid confusion and duplication
+	  during the transition parent. SPI and SPI flash must be
+	  enabled together (it is not possible to use driver model
+	  for one and not the other).
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index a0b6e02b54..c94353ba6a 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -2,8 +2,10 @@ config DM_SERIAL
 	bool "Enable Driver Model for serial drivers"
 	depends on DM
 	help
-	  If you want to use driver model for serial drivers, say Y.
-	  To use legacy serial drivers, say N.
+	  Enable driver model for serial. This replaces
+	  drivers/serial/serial.c with the serial uclass, which
+	  implements serial_putc() etc. The uclass interface is
+	  defined in include/serial.h.
 
 config UNIPHIER_SERIAL
 	bool "UniPhier on-chip UART support"
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 4cc00cd2f8..63b0cbf5da 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -8,6 +8,7 @@
 ifdef CONFIG_DM_SERIAL
 obj-y += serial-uclass.o
 obj-$(CONFIG_PL01X_SERIAL) += serial_pl01x.o
+obj-$(CONFIG_PPC) += serial_ppc.o
 else
 obj-y += serial.o
 obj-$(CONFIG_PL010_SERIAL) += serial_pl01x.o
diff --git a/drivers/serial/serial-uclass.c b/drivers/serial/serial-uclass.c
index 9131a8f93d..3fc7104359 100644
--- a/drivers/serial/serial-uclass.c
+++ b/drivers/serial/serial-uclass.c
@@ -258,6 +258,22 @@ static int serial_post_probe(struct udevice *dev)
 #endif
 	int ret;
 
+#if defined(CONFIG_NEEDS_MANUAL_RELOC)
+	if (ops->setbrg)
+		ops->setbrg += gd->reloc_off;
+	if (ops->getc)
+		ops->getc += gd->reloc_off;
+	if (ops->putc)
+		ops->putc += gd->reloc_off;
+	if (ops->pending)
+		ops->pending += gd->reloc_off;
+	if (ops->clear)
+		ops->clear += gd->reloc_off;
+#if CONFIG_POST & CONFIG_SYS_POST_UART
+	if (ops->loop)
+		ops->loop += gd->reloc_off
+#endif
+#endif
 	/* Set the baud rate */
 	if (ops->setbrg) {
 		ret = ops->setbrg(dev, gd->baudrate);
diff --git a/drivers/serial/serial_ppc.c b/drivers/serial/serial_ppc.c
new file mode 100644
index 0000000000..47141c64eb
--- /dev/null
+++ b/drivers/serial/serial_ppc.c
@@ -0,0 +1,40 @@
+/*
+ * Copyright (c) 2014 Google, Inc
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <ns16550.h>
+#include <serial.h>
+
+static const struct udevice_id ppc_serial_ids[] = {
+	{ .compatible = "ns16550" },
+	{ }
+};
+
+static int ppc_serial_ofdata_to_platdata(struct udevice *dev)
+{
+	struct ns16550_platdata *plat = dev_get_platdata(dev);
+	int ret;
+
+	ret = ns16550_serial_ofdata_to_platdata(dev);
+	if (ret)
+		return ret;
+	plat->clock = get_serial_clock();
+
+	return 0;
+}
+
+U_BOOT_DRIVER(serial_ns16550) = {
+	.name	= "serial_ppc",
+	.id	= UCLASS_SERIAL,
+	.of_match = ppc_serial_ids,
+	.ofdata_to_platdata = ppc_serial_ofdata_to_platdata,
+	.platdata_auto_alloc_size = sizeof(struct ns16550_platdata),
+	.priv_auto_alloc_size = sizeof(struct NS16550),
+	.probe = ns16550_serial_probe,
+	.ops	= &ns16550_serial_ops,
+	.flags	= DM_FLAG_PRE_RELOC,
+};
diff --git a/drivers/serial/serial_sh.c b/drivers/serial/serial_sh.c
index 7c1f271376..3641c9f834 100644
--- a/drivers/serial/serial_sh.c
+++ b/drivers/serial/serial_sh.c
@@ -1,78 +1,21 @@
 /*
  * SuperH SCIF device driver.
  * Copyright (C) 2013  Renesas Electronics Corporation
- * Copyright (C) 2007,2008,2010 Nobuhiro Iwamatsu
+ * Copyright (C) 2007,2008,2010, 2014 Nobuhiro Iwamatsu
  * Copyright (C) 2002 - 2008  Paul Mundt
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
 
 #include <common.h>
+#include <errno.h>
+#include <dm.h>
 #include <asm/io.h>
 #include <asm/processor.h>
-#include "serial_sh.h"
 #include <serial.h>
 #include <linux/compiler.h>
-
-#if defined(CONFIG_CONS_SCIF0)
-# define SCIF_BASE	SCIF0_BASE
-#elif defined(CONFIG_CONS_SCIF1)
-# define SCIF_BASE	SCIF1_BASE
-#elif defined(CONFIG_CONS_SCIF2)
-# define SCIF_BASE	SCIF2_BASE
-#elif defined(CONFIG_CONS_SCIF3)
-# define SCIF_BASE	SCIF3_BASE
-#elif defined(CONFIG_CONS_SCIF4)
-# define SCIF_BASE	SCIF4_BASE
-#elif defined(CONFIG_CONS_SCIF5)
-# define SCIF_BASE	SCIF5_BASE
-#elif defined(CONFIG_CONS_SCIF6)
-# define SCIF_BASE	SCIF6_BASE
-#elif defined(CONFIG_CONS_SCIF7)
-# define SCIF_BASE	SCIF7_BASE
-#else
-# error "Default SCIF doesn't set....."
-#endif
-
-#if defined(CONFIG_SCIF_A)
-	#define SCIF_BASE_PORT	PORT_SCIFA
-#else
-	#define SCIF_BASE_PORT	PORT_SCIF
-#endif
-
-static struct uart_port sh_sci = {
-	.membase	= (unsigned char*)SCIF_BASE,
-	.mapbase	= SCIF_BASE,
-	.type		= SCIF_BASE_PORT,
-};
-
-static void sh_serial_setbrg(void)
-{
-	DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_SCIF_USE_EXT_CLK
-	unsigned short dl = DL_VALUE(gd->baudrate, CONFIG_SH_SCIF_CLK_FREQ);
-	sci_out(&sh_sci, DL, dl);
-	/* Need wait: Clock * 1/dl × 1/16 */
-	udelay((1000000 * dl * 16 / CONFIG_SYS_CLK_FREQ) * 1000 + 1);
-#else
-	sci_out(&sh_sci, SCBRR,
-		SCBRR_VALUE(gd->baudrate, CONFIG_SH_SCIF_CLK_FREQ));
-#endif
-}
-
-static int sh_serial_init(void)
-{
-	sci_out(&sh_sci, SCSCR , SCSCR_INIT(&sh_sci));
-	sci_out(&sh_sci, SCSCR , SCSCR_INIT(&sh_sci));
-	sci_out(&sh_sci, SCSMR, 0);
-	sci_out(&sh_sci, SCSMR, 0);
-	sci_out(&sh_sci, SCFCR, SCFCR_RFRST|SCFCR_TFRST);
-	sci_in(&sh_sci, SCFCR);
-	sci_out(&sh_sci, SCFCR, 0);
-
-	serial_setbrg();
-	return 0;
-}
+#include <dm/platform_data/serial_sh.h>
+#include "serial_sh.h"
 
 #if defined(CONFIG_CPU_SH7760) || \
 	defined(CONFIG_CPU_SH7780) || \
@@ -86,7 +29,7 @@ static int scif_rxfill(struct uart_port *port)
 static int scif_rxfill(struct uart_port *port)
 {
 	if ((port->mapbase == 0xffe00000) ||
-		(port->mapbase == 0xffe08000)) {
+	    (port->mapbase == 0xffe08000)) {
 		/* SCIF0/1*/
 		return sci_in(port, SCRFDR) & 0xff;
 	} else {
@@ -109,80 +52,253 @@ static int scif_rxfill(struct uart_port *port)
 }
 #endif
 
-static int serial_rx_fifo_level(void)
+static void sh_serial_init_generic(struct uart_port *port)
 {
-	return scif_rxfill(&sh_sci);
+	sci_out(port, SCSCR , SCSCR_INIT(port));
+	sci_out(port, SCSCR , SCSCR_INIT(port));
+	sci_out(port, SCSMR, 0);
+	sci_out(port, SCSMR, 0);
+	sci_out(port, SCFCR, SCFCR_RFRST|SCFCR_TFRST);
+	sci_in(port, SCFCR);
+	sci_out(port, SCFCR, 0);
 }
 
-static void handle_error(void)
+static void
+sh_serial_setbrg_generic(struct uart_port *port, int clk, int baudrate)
 {
-	sci_in(&sh_sci, SCxSR);
-	sci_out(&sh_sci, SCxSR, SCxSR_ERROR_CLEAR(&sh_sci));
-	sci_in(&sh_sci, SCLSR);
-	sci_out(&sh_sci, SCLSR, 0x00);
+	if (port->clk_mode == EXT_CLK) {
+		unsigned short dl = DL_VALUE(baudrate, clk);
+		sci_out(port, DL, dl);
+		/* Need wait: Clock * 1/dl × 1/16 */
+		udelay((1000000 * dl * 16 / clk) * 1000 + 1);
+	} else {
+		sci_out(port, SCBRR, SCBRR_VALUE(baudrate, clk));
+	}
 }
 
-static void serial_raw_putc(const char c)
+static void handle_error(struct uart_port *port)
 {
-	while (1) {
-		/* Tx fifo is empty */
-		if (sci_in(&sh_sci, SCxSR) & SCxSR_TEND(&sh_sci))
-			break;
-	}
+	sci_in(port, SCxSR);
+	sci_out(port, SCxSR, SCxSR_ERROR_CLEAR(port));
+	sci_in(port, SCLSR);
+	sci_out(port, SCLSR, 0x00);
+}
+
+static int serial_raw_putc(struct uart_port *port, const char c)
+{
+	/* Tx fifo is empty */
+	if (!(sci_in(port, SCxSR) & SCxSR_TEND(port)))
+		return -EAGAIN;
 
-	sci_out(&sh_sci, SCxTDR, c);
-	sci_out(&sh_sci, SCxSR, sci_in(&sh_sci, SCxSR) & ~SCxSR_TEND(&sh_sci));
+	sci_out(port, SCxTDR, c);
+	sci_out(port, SCxSR, sci_in(port, SCxSR) & ~SCxSR_TEND(port));
+
+	return 0;
 }
 
-static void sh_serial_putc(const char c)
+static int serial_rx_fifo_level(struct uart_port *port)
 {
-	if (c == '\n')
-		serial_raw_putc('\r');
-	serial_raw_putc(c);
+	return scif_rxfill(port);
 }
 
-static int sh_serial_tstc(void)
+static int sh_serial_tstc_generic(struct uart_port *port)
 {
-	if (sci_in(&sh_sci, SCxSR) & SCIF_ERRORS) {
-		handle_error();
+	if (sci_in(port, SCxSR) & SCIF_ERRORS) {
+		handle_error(port);
 		return 0;
 	}
 
-	return serial_rx_fifo_level() ? 1 : 0;
+	return serial_rx_fifo_level(port) ? 1 : 0;
 }
 
-
-static int serial_getc_check(void)
+static int serial_getc_check(struct uart_port *port)
 {
 	unsigned short status;
 
-	status = sci_in(&sh_sci, SCxSR);
+	status = sci_in(port, SCxSR);
 
 	if (status & SCIF_ERRORS)
-		handle_error();
-	if (sci_in(&sh_sci, SCLSR) & SCxSR_ORER(&sh_sci))
-		handle_error();
-	return status & (SCIF_DR | SCxSR_RDxF(&sh_sci));
+		handle_error(port);
+	if (sci_in(port, SCLSR) & SCxSR_ORER(port))
+		handle_error(port);
+	return status & (SCIF_DR | SCxSR_RDxF(port));
 }
 
-static int sh_serial_getc(void)
+static int sh_serial_getc_generic(struct uart_port *port)
 {
 	unsigned short status;
 	char ch;
 
-	while (!serial_getc_check())
-		;
+	if (!serial_getc_check(port))
+		return -EAGAIN;
 
-	ch = sci_in(&sh_sci, SCxRDR);
-	status = sci_in(&sh_sci, SCxSR);
+	ch = sci_in(port, SCxRDR);
+	status = sci_in(port, SCxSR);
 
-	sci_out(&sh_sci, SCxSR, SCxSR_RDxF_CLEAR(&sh_sci));
+	sci_out(port, SCxSR, SCxSR_RDxF_CLEAR(port));
 
 	if (status & SCIF_ERRORS)
-			handle_error();
+		handle_error(port);
+
+	if (sci_in(port, SCLSR) & SCxSR_ORER(port))
+		handle_error(port);
+
+	return ch;
+}
+
+#ifdef CONFIG_DM_SERIAL
+
+static int sh_serial_pending(struct udevice *dev, bool input)
+{
+	struct uart_port *priv = dev_get_priv(dev);
+
+	return sh_serial_tstc_generic(priv);
+}
+
+static int sh_serial_putc(struct udevice *dev, const char ch)
+{
+	struct uart_port *priv = dev_get_priv(dev);
+
+	return serial_raw_putc(priv, ch);
+}
+
+static int sh_serial_getc(struct udevice *dev)
+{
+	struct uart_port *priv = dev_get_priv(dev);
+
+	return sh_serial_getc_generic(priv);
+}
+
+static int sh_serial_setbrg(struct udevice *dev, int baudrate)
+{
+	struct sh_serial_platdata *plat = dev_get_platdata(dev);
+	struct uart_port *priv = dev_get_priv(dev);
+
+	sh_serial_setbrg_generic(priv, plat->clk, baudrate);
+
+	return 0;
+}
+
+static int sh_serial_probe(struct udevice *dev)
+{
+	struct sh_serial_platdata *plat = dev_get_platdata(dev);
+	struct uart_port *priv = dev_get_priv(dev);
+
+	priv->membase	= (unsigned char *)plat->base;
+	priv->mapbase	= plat->base;
+	priv->type	= plat->type;
+	priv->clk_mode	= plat->clk_mode;
+
+	sh_serial_init_generic(priv);
+
+	return 0;
+}
+
+static const struct dm_serial_ops sh_serial_ops = {
+	.putc = sh_serial_putc,
+	.pending = sh_serial_pending,
+	.getc = sh_serial_getc,
+	.setbrg = sh_serial_setbrg,
+};
+
+U_BOOT_DRIVER(serial_sh) = {
+	.name	= "serial_sh",
+	.id	= UCLASS_SERIAL,
+	.probe	= sh_serial_probe,
+	.ops	= &sh_serial_ops,
+	.flags	= DM_FLAG_PRE_RELOC,
+	.priv_auto_alloc_size = sizeof(struct uart_port),
+};
+
+#else /* CONFIG_DM_SERIAL */
+
+#if defined(CONFIG_CONS_SCIF0)
+# define SCIF_BASE	SCIF0_BASE
+#elif defined(CONFIG_CONS_SCIF1)
+# define SCIF_BASE	SCIF1_BASE
+#elif defined(CONFIG_CONS_SCIF2)
+# define SCIF_BASE	SCIF2_BASE
+#elif defined(CONFIG_CONS_SCIF3)
+# define SCIF_BASE	SCIF3_BASE
+#elif defined(CONFIG_CONS_SCIF4)
+# define SCIF_BASE	SCIF4_BASE
+#elif defined(CONFIG_CONS_SCIF5)
+# define SCIF_BASE	SCIF5_BASE
+#elif defined(CONFIG_CONS_SCIF6)
+# define SCIF_BASE	SCIF6_BASE
+#elif defined(CONFIG_CONS_SCIF7)
+# define SCIF_BASE	SCIF7_BASE
+#else
+# error "Default SCIF doesn't set....."
+#endif
+
+#if defined(CONFIG_SCIF_A)
+	#define SCIF_BASE_PORT	PORT_SCIFA
+#else
+	#define SCIF_BASE_PORT	PORT_SCIF
+#endif
+
+static struct uart_port sh_sci = {
+	.membase	= (unsigned char *)SCIF_BASE,
+	.mapbase	= SCIF_BASE,
+	.type		= SCIF_BASE_PORT,
+#ifdef CONFIG_SCIF_USE_EXT_CLK
+	.clk_mode =	EXT_CLK,
+#endif
+};
+
+static void sh_serial_setbrg(void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+	struct uart_port *port = &sh_sci;
+
+	sh_serial_setbrg_generic(port, CONFIG_SH_SCIF_CLK_FREQ, gd->baudrate);
+}
+
+static int sh_serial_init(void)
+{
+	struct uart_port *port = &sh_sci;
+
+	sh_serial_init_generic(port);
+	serial_setbrg();
+
+	return 0;
+}
+
+static void sh_serial_putc(const char c)
+{
+	struct uart_port *port = &sh_sci;
+
+	if (c == '\n') {
+		while (1) {
+			if  (serial_raw_putc(port, '\r') != -EAGAIN)
+				break;
+		}
+	}
+	while (1) {
+		if  (serial_raw_putc(port, c) != -EAGAIN)
+			break;
+	}
+}
+
+static int sh_serial_tstc(void)
+{
+	struct uart_port *port = &sh_sci;
+
+	return sh_serial_tstc_generic(port);
+}
+
+static int sh_serial_getc(void)
+{
+	struct uart_port *port = &sh_sci;
+	int ch;
+
+	while (1) {
+		ch = sh_serial_getc_generic(port);
+		if (ch != -EAGAIN)
+			break;
+	}
 
-	if (sci_in(&sh_sci, SCLSR) & SCxSR_ORER(&sh_sci))
-		handle_error();
 	return ch;
 }
 
@@ -206,3 +322,4 @@ __weak struct serial_device *default_serial_console(void)
 {
 	return &sh_serial_drv;
 }
+#endif /* CONFIG_DM_SERIAL */
diff --git a/drivers/serial/serial_sh.h b/drivers/serial/serial_sh.h
index ef88c8f273..528aa7351d 100644
--- a/drivers/serial/serial_sh.h
+++ b/drivers/serial/serial_sh.h
@@ -2,18 +2,16 @@
  * Copy and modify from linux/drivers/serial/sh-sci.h
  */
 
+#include <dm/platform_data/serial_sh.h>
+
 struct uart_port {
 	unsigned long	iobase;		/* in/out[bwl] */
 	unsigned char	*membase;	/* read/write[bwl] */
 	unsigned long	mapbase;	/* for ioremap */
-	unsigned int	type;		/* port type */
+	enum sh_serial_type type;	/* port type */
+	enum sh_clk_mode clk_mode;	/* clock mode */
 };
 
-#define PORT_SCI	52
-#define PORT_SCIF	53
-#define PORT_SCIFA	83
-#define PORT_SCIFB	93
-
 #if defined(CONFIG_H83007) || defined(CONFIG_H83068)
 #include <asm/regs306x.h>
 #endif
@@ -526,6 +524,7 @@ SCIF_FNS(SCFDR,  0x1c, 16)
 SCIF_FNS(SCxTDR, 0x20,  8)
 SCIF_FNS(SCxRDR, 0x24,  8)
 SCIF_FNS(SCLSR,  0x00,  0)
+SCIF_FNS(DL,	 0x00,  0) /* dummy */
 #elif defined(CONFIG_ARCH_SH7372) || \
 	defined(CONFIG_R8A7740)
 SCIF_FNS(SCSMR,  0x00, 16)
@@ -541,6 +540,7 @@ SCIF_FNS(SCRFDR, 0x3c, 16)
 SCIx_FNS(SCxTDR, 0x20,  8, 0x40,  8)
 SCIx_FNS(SCxRDR, 0x24,  8, 0x60,  8)
 SCIF_FNS(SCLSR,  0x00,  0)
+SCIF_FNS(DL,	 0x00,  0) /* dummy */
 #elif defined(CONFIG_CPU_SH7723) ||\
 	defined(CONFIG_CPU_SH7724)
 SCIx_FNS(SCSMR,  0x00, 16, 0x00, 16)
@@ -555,6 +555,7 @@ SCIF_FNS(SCFER,  0x10, 16)
 SCIF_FNS(SCFCR,  0x18, 16)
 SCIF_FNS(SCFDR,  0x1c, 16)
 SCIF_FNS(SCLSR,  0x24, 16)
+SCIF_FNS(DL,	 0x00,  0) /* dummy */
 #else
 /*      reg      SCI/SH3   SCI/SH4  SCIF/SH3   SCIF/SH4  SCI/H8*/
 /*      name     off  sz   off  sz   off  sz   off  sz   off  sz*/
@@ -583,18 +584,21 @@ SCIF_FNS(SCRFDR,		     0x0e, 16, 0x20, 16)
 SCIF_FNS(SCSPTR,			0,  0, 0x24, 16)
 SCIF_FNS(SCLSR,				0,  0, 0x28, 16)
 #else
+
 SCIF_FNS(SCFDR,                      0x0e, 16, 0x1C, 16)
 #if defined(CONFIG_CPU_SH7722)
 SCIF_FNS(SCSPTR,                        0,  0, 0, 0)
 #else
 SCIF_FNS(SCSPTR,                        0,  0, 0x20, 16)
 #endif
+SCIF_FNS(SCLSR,                         0,  0, 0x24, 16)
+#endif
 #if defined(CONFIG_R8A7790) || defined(CONFIG_R8A7791) || \
 	defined(CONFIG_R8A7793) || defined(CONFIG_R8A7794)
 SCIF_FNS(DL,				0,  0, 0x30, 16)
 SCIF_FNS(CKS,				0,  0, 0x34, 16)
-#endif
-SCIF_FNS(SCLSR,                         0,  0, 0x24, 16)
+#else
+SCIF_FNS(DL,				0,  0, 0x0,  0) /* dummy */
 #endif
 #endif
 #define sci_in(port, reg) sci_##reg##_in(port)
@@ -725,14 +729,14 @@ static inline int sci_rxd_in(struct uart_port *port)
 #define SCBRR_VALUE(bps, clk) (((clk*2)+16*bps)/(32*bps)-1)
 #elif defined(CONFIG_CPU_SH7723) ||\
 	defined(CONFIG_CPU_SH7724)
-static inline int scbrr_calc(struct uart_port port, int bps, int clk)
+static inline int scbrr_calc(struct uart_port *port, int bps, int clk)
 {
-	if (port.type == PORT_SCIF)
+	if (port->type == PORT_SCIF)
 		return (clk+16*bps)/(32*bps)-1;
 	else
 		return ((clk*2)+16*bps)/(16*bps)-1;
 }
-#define SCBRR_VALUE(bps, clk) scbrr_calc(sh_sci, bps, clk)
+#define SCBRR_VALUE(bps, clk) scbrr_calc(port, bps, clk)
 #elif defined(__H8300H__) || defined(__H8300S__)
 #define SCBRR_VALUE(bps, clk) (((clk*1000/32)/bps)-1)
 #elif defined(CONFIG_R8A7790) || defined(CONFIG_R8A7791) || \
@@ -742,3 +746,7 @@ static inline int scbrr_calc(struct uart_port port, int bps, int clk)
 #else /* Generic SH */
 #define SCBRR_VALUE(bps, clk) ((clk+16*bps)/(32*bps)-1)
 #endif
+
+#ifndef DL_VALUE
+#define DL_VALUE(bps, clk) 0
+#endif
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index e1678e63e6..7ae2727cf7 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -2,5 +2,11 @@ config DM_SPI
 	bool "Enable Driver Model for SPI drivers"
 	depends on DM
 	help
-	  If you want to use driver model for SPI drivers, say Y.
-	  To use legacy SPI drivers, say N.
+	  Enable driver model for SPI. The SPI slave interface
+	  (spi_setup_slave(), spi_xfer(), etc.) is then implemented by
+	  the SPI uclass. Drivers provide methods to access the SPI
+	  buses that they control. The uclass interface is defined in
+	  include/spi.h. The existing spi_slave structure is attached
+	  as 'parent data' to every slave on each bus. Slaves
+	  typically use driver-private data instead of extending the
+	  spi_slave structure.
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
new file mode 100644
index 0000000000..3c6b36d1cf
--- /dev/null
+++ b/drivers/thermal/Kconfig
@@ -0,0 +1,7 @@
+config DM_THERMAL
+	bool "Driver support for thermal devices"
+	help
+	  Enable support for temporary-sensing devices. Some SoCs have on-chip
+	  temperature sensors to permit warnings, speed throttling or even
+	  automatic power-off when the temperature gets too high or low. Other
+	  devices may be discrete but connected on a suitable bus.