ddr: marvell: a38x: Sync code with Marvell mv-ddr-marvell repository

This syncs drivers/ddr/marvell/a38x/ with the master branch of repository
https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git up to the
commit 7c351731d196 ("Merge pull request #29 from pali/sync-a38x-uboot").

This patch was created by following steps:

1. Replace all a38x files in U-Boot tree by files from upstream github
   Marvell mv-ddr-marvell repository.

2. Run following command to omit portions not relevant for a38x and ddr3:

    files=drivers/ddr/marvell/a38x/*
    sed 's/#if defined(CONFIG_ARMADA_38X) || defined(CONFIG_ARMADA_39X)/#ifdef TRUE/' -i $files
    unifdef -m -UMV_DDR -UMV_DDR_ATF -UCONFIG_DDR4 -UCONFIG_APN806 \
        -UCONFIG_MC_STATIC -UCONFIG_MC_STATIC_PRINT -UCONFIG_PHY_STATIC \
        -UCONFIG_PHY_STATIC_PRINT -UCONFIG_CUSTOMER_BOARD_SUPPORT \
        -UCONFIG_A3700 -UA3900 -UA80X0 -UA70X0 -DTRUE $files

3. Manually omit SPDX-License-Identifier changes from this patch as
   upstream license in  upstream github repository contains long license
   texts and U-Boot is using just SPDX-License-Identifier.

After applying this patch, a38x ddr3 code in upstream Marvell github
repository and in U-Boot would be fully identical. So in future applying
above steps could be used to sync code again.

The only change in this patch is removal of dead code and some fixes with
include files.

Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>

10 files changed, 6 insertions, 40 deletions

diff --git a/drivers/ddr/marvell/a38x/ddr3_debug.c b/drivers/ddr/marvell/a38x/ddr3_debug.c
index 22e0cc4d91..f5fc964d6f 100644
--- a/drivers/ddr/marvell/a38x/ddr3_debug.c
+++ b/drivers/ddr/marvell/a38x/ddr3_debug.c
@@ -6,7 +6,6 @@
 #include "ddr3_init.h"
 #include "mv_ddr_training_db.h"
 #include "mv_ddr_regs.h"
-#include <log.h>
 
 u8 is_reg_dump = 0;
 u8 debug_pbs = DEBUG_LEVEL_ERROR;
diff --git a/drivers/ddr/marvell/a38x/ddr3_init.c b/drivers/ddr/marvell/a38x/ddr3_init.c
index 7488770268..f878b4512b 100644
--- a/drivers/ddr/marvell/a38x/ddr3_init.c
+++ b/drivers/ddr/marvell/a38x/ddr3_init.c
@@ -77,9 +77,6 @@ int ddr3_init(void)
 		return status;
 	}
 
-#if defined(CONFIG_PHY_STATIC_PRINT)
-	mv_ddr_phy_static_print();
-#endif
 
 	/* Post MC/PHY initializations */
 	mv_ddr_post_training_soc_config(ddr_type);
diff --git a/drivers/ddr/marvell/a38x/ddr3_training.c b/drivers/ddr/marvell/a38x/ddr3_training.c
index 2b3af23202..2512b58cb7 100644
--- a/drivers/ddr/marvell/a38x/ddr3_training.c
+++ b/drivers/ddr/marvell/a38x/ddr3_training.c
@@ -7,8 +7,6 @@
 #include "mv_ddr_common.h"
 #include "mv_ddr_training_db.h"
 #include "mv_ddr_regs.h"
-#include <log.h>
-#include <linux/delay.h>
 
 #define GET_CS_FROM_MASK(mask)	(cs_mask2_num[mask])
 #define CS_CBE_VALUE(cs_num)	(cs_cbe_reg[cs_num])
@@ -207,7 +205,6 @@ static int ddr3_tip_pad_inv(void)
 		if (tm->interface_params[0].as_bus_params[sphy].
 		    is_ck_swap == 1 && sphy == 0) {
 /* TODO: move this code to per platform one */
-#if defined(CONFIG_ARMADA_38X) || defined(CONFIG_ARMADA_39X)
 			/* clock swap for both cs0 and cs1 */
 			data = (INVERT_PAD << INV_PAD2_OFFS |
 				INVERT_PAD << INV_PAD6_OFFS |
@@ -219,9 +216,6 @@ static int ddr3_tip_pad_inv(void)
 						       DDR_PHY_CONTROL,
 						       PHY_CTRL_PHY_REG,
 						       data, data);
-#else /* !CONFIG_ARMADA_38X && !CONFIG_ARMADA_39X */
-#pragma message "unknown platform to configure ddr clock swap"
-#endif
 		}
 	}
 
@@ -2014,9 +2008,7 @@ int ddr3_tip_adll_regs_bypass(u32 dev_num, u32 reg_val1, u32 reg_val2)
 static int ddr3_tip_ddr3_training_main_flow(u32 dev_num)
 {
 /* TODO: enable this functionality for other platforms */
-#if defined(CONFIG_ARMADA_38X) || defined(CONFIG_ARMADA_39X)
 	struct init_cntr_param init_cntr_prm;
-#endif
 	int ret = MV_OK;
 	int adll_bypass_flag = 0;
 	u32 if_id;
@@ -2050,7 +2042,6 @@ static int ddr3_tip_ddr3_training_main_flow(u32 dev_num)
 	}
 
 /* TODO: enable this functionality for other platforms */
-#if defined(CONFIG_ARMADA_38X) || defined(CONFIG_ARMADA_39X)
 	if (is_adll_calib_before_init != 0) {
 		DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
 				  ("with adll calib before init\n"));
@@ -2081,7 +2072,6 @@ static int ddr3_tip_ddr3_training_main_flow(u32 dev_num)
 				return MV_FAIL;
 		}
 	}
-#endif
 
 	ret = adll_calibration(dev_num, ACCESS_TYPE_MULTICAST, 0, freq);
 	if (ret != MV_OK) {
@@ -2905,3 +2895,4 @@ unsigned int mv_ddr_misl_phy_odt_n_get(void)
 
 	return odt_n;
 }
+
diff --git a/drivers/ddr/marvell/a38x/ddr3_training_ip_engine.c b/drivers/ddr/marvell/a38x/ddr3_training_ip_engine.c
index 5fd9a052fa..102f9bd633 100644
--- a/drivers/ddr/marvell/a38x/ddr3_training_ip_engine.c
+++ b/drivers/ddr/marvell/a38x/ddr3_training_ip_engine.c
@@ -6,8 +6,6 @@
 #include "ddr3_init.h"
 #include "mv_ddr_regs.h"
 #include "ddr_training_ip_db.h"
-#include <image.h>
-#include <linux/delay.h>
 
 #define PATTERN_1	0x55555555
 #define PATTERN_2	0xaaaaaaaa
@@ -614,9 +612,9 @@ int ddr3_tip_load_pattern_to_odpg(u32 dev_num, enum hws_access_type access_type,
 			      MASK_ALL_BITS));
 	}
 
-	CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
-				       ODPG_DATA_BUFFER_OFFS_REG,
-				       load_addr, MASK_ALL_BITS));
+	CHECK_STATUS(ddr3_tip_if_write
+		     (dev_num, access_type, if_id,
+		      ODPG_DATA_BUFFER_OFFS_REG, load_addr, MASK_ALL_BITS));
 
 	return MV_OK;
 }
diff --git a/drivers/ddr/marvell/a38x/ddr3_training_leveling.c b/drivers/ddr/marvell/a38x/ddr3_training_leveling.c
index dadb06b318..7f7df6794a 100644
--- a/drivers/ddr/marvell/a38x/ddr3_training_leveling.c
+++ b/drivers/ddr/marvell/a38x/ddr3_training_leveling.c
@@ -7,7 +7,6 @@
 #include "mv_ddr_training_db.h"
 #include "ddr_training_ip_db.h"
 #include "mv_ddr_regs.h"
-#include <linux/delay.h>
 
 #define WL_ITERATION_NUM	10
 
diff --git a/drivers/ddr/marvell/a38x/ddr_ml_wrapper.h b/drivers/ddr/marvell/a38x/ddr_ml_wrapper.h
index ac9250f74e..7357311965 100644
--- a/drivers/ddr/marvell/a38x/ddr_ml_wrapper.h
+++ b/drivers/ddr/marvell/a38x/ddr_ml_wrapper.h
@@ -13,9 +13,7 @@
 #include <asm/arch/cpu.h>
 #include <asm/arch/soc.h>
 
-#if defined(CONFIG_ARMADA_38X) || defined(CONFIG_ARMADA_39X)
 #define INTER_REGS_BASE	SOC_REGS_PHY_BASE
-#endif
 
 /*
  * MV_DEBUG_INIT need to be defines, otherwise the output of the
diff --git a/drivers/ddr/marvell/a38x/mv_ddr_plat.c b/drivers/ddr/marvell/a38x/mv_ddr_plat.c
index 0d1df189e8..da0d63d4f7 100644
--- a/drivers/ddr/marvell/a38x/mv_ddr_plat.c
+++ b/drivers/ddr/marvell/a38x/mv_ddr_plat.c
@@ -8,7 +8,6 @@
 #include "mv_ddr_training_db.h"
 #include "mv_ddr_regs.h"
 #include "mv_ddr_sys_env_lib.h"
-#include <linux/delay.h>
 
 #define DDR_INTERFACES_NUM		1
 #define DDR_INTERFACE_OCTETS_NUM	5
diff --git a/drivers/ddr/marvell/a38x/mv_ddr_plat.h b/drivers/ddr/marvell/a38x/mv_ddr_plat.h
index 281d4c2301..44998847c2 100644
--- a/drivers/ddr/marvell/a38x/mv_ddr_plat.h
+++ b/drivers/ddr/marvell/a38x/mv_ddr_plat.h
@@ -6,6 +6,8 @@
 #ifndef _MV_DDR_PLAT_H
 #define _MV_DDR_PLAT_H
 
+#include <linux/delay.h>
+
 #define MAX_DEVICE_NUM			1
 #define MAX_INTERFACE_NUM		1
 #define MAX_BUS_NUM			5
diff --git a/drivers/ddr/marvell/a38x/mv_ddr_sys_env_lib.h b/drivers/ddr/marvell/a38x/mv_ddr_sys_env_lib.h
index dc6977c334..cf5142094d 100644
--- a/drivers/ddr/marvell/a38x/mv_ddr_sys_env_lib.h
+++ b/drivers/ddr/marvell/a38x/mv_ddr_sys_env_lib.h
@@ -78,20 +78,6 @@ enum suspend_wakeup_status {
  * set '-2'
  * If suspend to RAM is not supported set '-1'
  */
-#ifdef CONFIG_CUSTOMER_BOARD_SUPPORT
-#ifdef CONFIG_ARMADA_38X
-#define MV_BOARD_WAKEUP_GPIO_INFO {		\
-	{A38X_CUSTOMER_BOARD_ID0,	-1 },	\
-	{A38X_CUSTOMER_BOARD_ID0,	-1 },	\
-};
-#else
-#define MV_BOARD_WAKEUP_GPIO_INFO {		\
-	{A39X_CUSTOMER_BOARD_ID0,	-1 },	\
-	{A39X_CUSTOMER_BOARD_ID0,	-1 },	\
-};
-#endif /* CONFIG_ARMADA_38X */
-
-#else
 
 #ifdef CONFIG_ARMADA_38X
 #define MV_BOARD_WAKEUP_GPIO_INFO {	\
@@ -109,7 +95,6 @@ enum suspend_wakeup_status {
 	{A39X_DB_69XX_ID, -1 },		\
 };
 #endif /* CONFIG_ARMADA_38X */
-#endif /* CONFIG_CUSTOMER_BOARD_SUPPORT */
 
 enum suspend_wakeup_status mv_ddr_sys_env_suspend_wakeup_check(void);
 u32 mv_ddr_sys_env_get_cs_ena_from_reg(void);
diff --git a/drivers/ddr/marvell/a38x/xor.c b/drivers/ddr/marvell/a38x/xor.c
index 98fb39eaf0..7bc6268293 100644
--- a/drivers/ddr/marvell/a38x/xor.c
+++ b/drivers/ddr/marvell/a38x/xor.c
@@ -347,10 +347,8 @@ void ddr3_new_tip_ecc_scrub(void)
 	for (cs_c = 0; cs_c < max_cs; cs_c++)
 		cs_ena |= 1 << cs_c;
 
-#if defined(CONFIG_ARMADA_38X) || defined(CONFIG_ARMADA_39X)
 	/* all chip-selects are of same size */
 	ddr3_calc_mem_cs_size(0, &cs_mem_size_mb);
-#endif
 	cs_mem_size = cs_mem_size_mb * _1M;
 	mv_sys_xor_init(max_cs, cs_ena, cs_mem_size, 0);
 	total_mem_size = max_cs * cs_mem_size;