mtd: nand: lpc32xx slc: disable DMA support in SPL builds

Testing and analysis shows that at the moment LPC32xx NAND SLC driver
can not get PL080 DMA backbone support in SPL build, because SPL NAND
loaders operate with subpage (ECC step to be precisely) reads, and
this is not supported in the NAND SLC + DMA + hardware ECC calculation
bundle.

The change removes a cautious build time warning and explicitly
disables DMA flavour of the driver for SPL builds, to reduce the
amound of #ifdef sections the code blocks are minimally reorganized.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>

1 files changed, 32 insertions, 46 deletions

diff --git a/drivers/mtd/nand/raw/lpc32xx_nand_slc.c b/drivers/mtd/nand/raw/lpc32xx_nand_slc.c
index 99f6e15f4e..8615b112a2 100644
--- a/drivers/mtd/nand/raw/lpc32xx_nand_slc.c
+++ b/drivers/mtd/nand/raw/lpc32xx_nand_slc.c
@@ -2,13 +2,12 @@
 /*
  * LPC32xx SLC NAND flash controller driver
  *
- * (C) Copyright 2015 Vladimir Zapolskiy <vz@mleia.com>
+ * (C) Copyright 2015-2018 Vladimir Zapolskiy <vz@mleia.com>
+ * Copyright (c) 2015 Tyco Fire Protection Products.
  *
  * Hardware ECC support original source code
  * Copyright (C) 2008 by NXP Semiconductors
  * Author: Kevin Wells
- *
- * Copyright (c) 2015 Tyco Fire Protection Products.
  */
 
 #include <common.h>
@@ -22,10 +21,6 @@
 #include <asm/arch/dma.h>
 #include <asm/arch/cpu.h>
 
-#if defined(CONFIG_DMA_LPC32XX) && defined(CONFIG_SPL_BUILD)
-#warning "DMA support in SPL image is not tested"
-#endif
-
 struct lpc32xx_nand_slc_regs {
 	u32 data;
 	u32 addr;
@@ -78,16 +73,14 @@ struct lpc32xx_nand_slc_regs {
  * Note: For large page devices, the default layouts are used. */
 static struct nand_ecclayout lpc32xx_nand_oob_16 = {
 	.eccbytes = 6,
-	.eccpos = {10, 11, 12, 13, 14, 15},
+	.eccpos = { 10, 11, 12, 13, 14, 15, },
 	.oobfree = {
-		{.offset = 0,
-		 . length = 4},
-		{.offset = 6,
-		 . length = 4}
-		}
+		{ .offset = 0, .length = 4, },
+		{ .offset = 6, .length = 4, },
+	}
 };
 
-#if defined(CONFIG_DMA_LPC32XX)
+#if defined(CONFIG_DMA_LPC32XX) && !defined(CONFIG_SPL_BUILD)
 #define ECCSTEPS	(CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE)
 
 /*
@@ -165,7 +158,7 @@ static int lpc32xx_nand_dev_ready(struct mtd_info *mtd)
 	return readl(&lpc32xx_nand_slc_regs->stat) & STAT_NAND_READY;
 }
 
-#if defined(CONFIG_DMA_LPC32XX)
+#if defined(CONFIG_DMA_LPC32XX) && !defined(CONFIG_SPL_BUILD)
 /*
  * Prepares DMA descriptors for NAND RD/WR operations
  * If the size is < 256 Bytes then it is assumed to be
@@ -324,7 +317,6 @@ static void lpc32xx_nand_xfer(struct mtd_info *mtd, const u8 *buf,
 	if (unlikely(ret < 0))
 		BUG();
 
-
 	/* Wait for NAND to be ready */
 	while (!lpc32xx_nand_dev_ready(mtd))
 		;
@@ -404,46 +396,18 @@ int lpc32xx_correct_data(struct mtd_info *mtd, u_char *dat,
 
 	return ret2;
 }
-#endif
 
-#if defined(CONFIG_DMA_LPC32XX)
 static void lpc32xx_dma_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
 {
 	lpc32xx_nand_xfer(mtd, buf, len, 1);
 }
-#else
-static void lpc32xx_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
-{
-	while (len-- > 0)
-		*buf++ = readl(&lpc32xx_nand_slc_regs->data);
-}
-#endif
 
-static uint8_t lpc32xx_read_byte(struct mtd_info *mtd)
-{
-	return readl(&lpc32xx_nand_slc_regs->data);
-}
-
-#if defined(CONFIG_DMA_LPC32XX)
 static void lpc32xx_dma_write_buf(struct mtd_info *mtd, const uint8_t *buf,
 				  int len)
 {
 	lpc32xx_nand_xfer(mtd, buf, len, 0);
 }
-#else
-static void lpc32xx_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
-{
-	while (len-- > 0)
-		writel(*buf++, &lpc32xx_nand_slc_regs->data);
-}
-#endif
-
-static void lpc32xx_write_byte(struct mtd_info *mtd, uint8_t byte)
-{
-	writel(byte, &lpc32xx_nand_slc_regs->data);
-}
 
-#if defined(CONFIG_DMA_LPC32XX)
 /* Reuse the logic from "nand_read_page_hwecc()" */
 static int lpc32xx_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
 				uint8_t *buf, int oob_required, int page)
@@ -511,8 +475,30 @@ static int lpc32xx_write_page_hwecc(struct mtd_info *mtd,
 
 	return 0;
 }
+#else
+static void lpc32xx_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+	while (len-- > 0)
+		*buf++ = readl(&lpc32xx_nand_slc_regs->data);
+}
+
+static void lpc32xx_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
+{
+	while (len-- > 0)
+		writel(*buf++, &lpc32xx_nand_slc_regs->data);
+}
 #endif
 
+static uint8_t lpc32xx_read_byte(struct mtd_info *mtd)
+{
+	return readl(&lpc32xx_nand_slc_regs->data);
+}
+
+static void lpc32xx_write_byte(struct mtd_info *mtd, uint8_t byte)
+{
+	writel(byte, &lpc32xx_nand_slc_regs->data);
+}
+
 /*
  * LPC32xx has only one SLC NAND controller, don't utilize
  * CONFIG_SYS_NAND_SELF_INIT to be able to reuse this function
@@ -520,7 +506,7 @@ static int lpc32xx_write_page_hwecc(struct mtd_info *mtd,
  */
 int board_nand_init(struct nand_chip *lpc32xx_chip)
 {
-#if defined(CONFIG_DMA_LPC32XX)
+#if defined(CONFIG_DMA_LPC32XX) && !defined(CONFIG_SPL_BUILD)
 	int ret;
 
 	/* Acquire a channel for our use */
@@ -543,7 +529,7 @@ int board_nand_init(struct nand_chip *lpc32xx_chip)
 	lpc32xx_chip->read_byte  = lpc32xx_read_byte;
 	lpc32xx_chip->write_byte = lpc32xx_write_byte;
 
-#if defined(CONFIG_DMA_LPC32XX)
+#if defined(CONFIG_DMA_LPC32XX) && !defined(CONFIG_SPL_BUILD)
 	/* Hardware ECC calculation is supported when DMA driver is selected */
 	lpc32xx_chip->ecc.mode		= NAND_ECC_HW;