Merge branch 'master' of git://git.denx.de/u-boot-nios

* 'master' of git://git.denx.de/u-boot-nios:
  nios2: Offer ft_board_setup() capability and call fdt_fixup_ethernet().
  board/nios2-generic: Use altera_pio driver and remove board specific driver
  gpio: Add driver for Altera's PIO core
  nios2: Pseudo implement dcache_status/enable/disable()

2 files changed, 300 insertions, 0 deletions

diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index e1142d14be..e22c09689d 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -36,6 +36,7 @@ COBJS-$(CONFIG_PCA9698)		+= pca9698.o
 COBJS-$(CONFIG_S5P)		+= s5p_gpio.o
 COBJS-$(CONFIG_TEGRA2_GPIO)	+= tegra2_gpio.o
 COBJS-$(CONFIG_DA8XX_GPIO)	+= da8xx_gpio.o
+COBJS-$(CONFIG_ALTERA_PIO)	+= altera_pio.o
 
 COBJS	:= $(COBJS-y)
 SRCS 	:= $(COBJS:.o=.c)
diff --git a/drivers/gpio/altera_pio.c b/drivers/gpio/altera_pio.c
new file mode 100644
index 0000000000..fb03760735
--- /dev/null
+++ b/drivers/gpio/altera_pio.c
@@ -0,0 +1,299 @@
+/*
+ * Driver for Altera's PIO ip core
+ *
+ * Copyright (C) 2011  Missing Link Electronics
+ *                     Joachim Foerster <joachim@missinglinkelectronics.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * To use this driver, in your board's config. header:
+ * #define CONFIG_ALTERA_PIO
+ * #define CONFIG_SYS_ALTERA_PIO_NUM <number-of-pio-cores>
+ * #define CONFIG_SYS_ALTERA_PIO_GPIO_NUM <total-number-of-gpios>
+ * And in your board's early setup routine:
+ * altera_pio_init(<baseaddr>, <width>, 'i'|'o'|'t',
+ *                 <reset-value>, <neg-mask>, "label");
+ *  - 'i'|'o'|'t': PIO is input-only/output-only/tri-state
+ *  - <reset-value>: for correct initial status display, output-only
+ *  - <neg-mask> is meant to be used to in cases of active-low
+ *    GPIOs, such as LEDs and buttons (on/pressed == 0). Each bit
+ *    which is 1 in <neg-mask> inverts the corresponding GPIO's value
+ *    before set/after get. So: gpio_set_value(gpio, 1) => LED on .
+ *
+ * Do NOT define CONFIG_SYS_GPIO_BASE !
+ *
+ * Optionally, in your board's config. header:
+ * - To force a GPIO numbering scheme like in Linux ...
+ * #define CONFIG_GPIO_DOWNTO_NUMBERING
+ * ... starting with 255 (default)
+ * #define CONFIG_GPIO_DOWNTO_MAX 255
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+
+#ifdef CONFIG_GPIO_DOWNTO_NUMBERING
+#ifndef CONFIG_GPIO_DOWNTO_MAX
+#define CONFIG_GPIO_DOWNTO_MAX 255
+#endif
+#endif
+
+#define ALTERA_PIO_DATA		0x0
+#define ALTERA_PIO_DIR		0x4
+
+#define GPIO_LABEL_SIZE		9
+
+
+static struct altera_pio {
+	u32 base;
+	u8 width;
+	char iot;
+	u32 negmask;
+	u32 sh_data;
+	u32 sh_dir;
+	int gidx;
+	char label[GPIO_LABEL_SIZE];
+} pios[CONFIG_SYS_ALTERA_PIO_NUM];
+
+static int pio_num;
+
+static struct altera_pio_gpio {
+	unsigned num;
+	struct altera_pio *pio;
+	char reqlabel[GPIO_LABEL_SIZE];
+} gpios[CONFIG_SYS_ALTERA_PIO_GPIO_NUM];
+
+static int pio_gpio_num;
+
+
+static int altera_pio_gidx(unsigned gpio)
+{
+	int i;
+
+	for (i = 0; i < pio_gpio_num; ++i) {
+		if (gpio == gpios[i].num)
+			break;
+	}
+	if (i >= pio_gpio_num)
+		return -1;
+	return i;
+}
+
+static struct altera_pio *altera_pio_get_and_mask(unsigned gpio, u32 *mask)
+{
+	int gidx = altera_pio_gidx(gpio);
+	if (gidx < 0)
+		return NULL;
+	if (mask)
+		*mask = 1 << (gidx - gpios[gidx].pio->gidx);
+	return gpios[gidx].pio;
+}
+
+#define altera_pio_use_gidx(_gidx, _reqlabel) \
+	{ strncpy(gpios[_gidx].reqlabel, _reqlabel, GPIO_LABEL_SIZE); }
+#define altera_pio_unuse_gidx(_gidx) { gpios[_gidx].reqlabel[0] = '\0'; }
+#define altera_pio_is_gidx_used(_gidx) (gpios[_gidx].reqlabel[0] != '\0')
+
+static int altera_pio_gpio_init(struct altera_pio *pio, u8 width)
+{
+	u8 gidx = pio_gpio_num;
+	int i;
+
+	if (!width)
+		return -1;
+	if ((pio_gpio_num + width) > CONFIG_SYS_ALTERA_PIO_GPIO_NUM)
+		return -1;
+
+	for (i = 0; i < width; ++i) {
+#ifdef CONFIG_GPIO_DOWNTO_NUMBERING
+		gpios[pio_gpio_num + i].num = \
+			CONFIG_GPIO_DOWNTO_MAX + 1 - gidx - width + i;
+#else
+		gpios[pio_gpio_num + i].num = pio_gpio_num + i;
+#endif
+		gpios[pio_gpio_num + i].pio = pio;
+		altera_pio_unuse_gidx(pio_gpio_num + i);
+	}
+	pio_gpio_num += width;
+	return gidx;
+}
+
+int altera_pio_init(u32 base, u8 width, char iot, u32 rstval, u32 negmask,
+		 const char *label)
+{
+	if (pio_num >= CONFIG_SYS_ALTERA_PIO_NUM)
+		return -1;
+
+	pios[pio_num].base = base;
+	pios[pio_num].width = width;
+	pios[pio_num].iot = iot;
+	switch (iot) {
+	case 'i':
+		/* input only */
+		pios[pio_num].sh_dir = 0;
+		pios[pio_num].sh_data = readl(base + ALTERA_PIO_DATA);
+		break;
+	case 'o':
+		/* output only */
+		pios[pio_num].sh_dir = 0xffffffff & ((1 << width) - 1);
+		pios[pio_num].sh_data = rstval;
+		break;
+	case 't':
+		/* bidir, tri-state */
+		pios[pio_num].sh_dir = readl(base + ALTERA_PIO_DIR);
+		pios[pio_num].sh_data = readl(base + ALTERA_PIO_DATA);
+		break;
+	default:
+		return -1;
+	}
+	pios[pio_num].negmask = negmask & ((1 << width) - 1);
+	pios[pio_num].gidx = altera_pio_gpio_init(&pios[pio_num], width);
+	if (pios[pio_num].gidx < 0)
+		return -1;
+	strncpy(pios[pio_num].label, label, GPIO_LABEL_SIZE);
+	return pio_num++;
+}
+
+void altera_pio_info(void)
+{
+	int i;
+	int j;
+	int gidx;
+	u32 mask;
+
+	for (i = 0; i < pio_num; ++i) {
+		printf("Altera PIO % 2d, @0x%08x, "
+			"width: %u, label: %s\n",
+		       i, pios[i].base, pios[i].width, pios[i].label);
+		gidx = pios[i].gidx;
+		for (j = gidx; j < (gidx + pios[i].width); ++j) {
+			mask = 1 << (j - gidx);
+			printf("\tGPIO % 4d: %s %s [%c] %s\n",
+				gpios[j].num,
+				gpios[j].pio->sh_dir & mask ? "out" : " in",
+				gpio_get_value(gpios[j].num) ? "set" : "clr",
+				altera_pio_is_gidx_used(j) ? 'x' : ' ',
+				gpios[j].reqlabel);
+		}
+	}
+}
+
+
+int gpio_request(unsigned gpio, const char *label)
+{
+	int gidx = altera_pio_gidx(gpio);
+	if (gidx < 0)
+		return gidx;
+	if (altera_pio_is_gidx_used(gidx))
+		return -1;
+
+	altera_pio_use_gidx(gidx, label);
+	return 0;
+}
+
+int gpio_free(unsigned gpio)
+{
+	int gidx = altera_pio_gidx(gpio);
+	if (gidx < 0)
+		return gidx;
+	if (!altera_pio_is_gidx_used(gidx))
+		return -1;
+
+	altera_pio_unuse_gidx(gidx);
+	return 0;
+}
+
+int gpio_direction_input(unsigned gpio)
+{
+	u32 mask;
+	struct altera_pio *pio;
+
+	pio = altera_pio_get_and_mask(gpio, &mask);
+	if (!pio)
+		return -1;
+	if (pio->iot == 'o')
+		return -1;
+
+	writel(pio->sh_dir &= ~mask, pio->base + ALTERA_PIO_DIR);
+	return 0;
+}
+
+int gpio_direction_output(unsigned gpio, int value)
+{
+	u32 mask;
+	struct altera_pio *pio;
+
+	pio = altera_pio_get_and_mask(gpio, &mask);
+	if (!pio)
+		return -1;
+	if (pio->iot == 'i')
+		return -1;
+
+	value = (pio->negmask & mask) ? !value : value;
+	if (value)
+		pio->sh_data |= mask;
+	else
+		pio->sh_data &= ~mask;
+	writel(pio->sh_data, pio->base + ALTERA_PIO_DATA);
+	writel(pio->sh_dir |= mask, pio->base + ALTERA_PIO_DIR);
+	return 0;
+}
+
+int gpio_get_value(unsigned gpio)
+{
+	u32 mask;
+	struct altera_pio *pio;
+	u32 val;
+
+	pio = altera_pio_get_and_mask(gpio, &mask);
+	if (!pio)
+		return -1;
+
+	if ((pio->sh_dir & mask) || (pio->iot == 'o'))
+		val = pio->sh_data & mask;
+	else
+		val = readl(pio->base + ALTERA_PIO_DATA) & mask;
+	return (pio->negmask & mask) ? !val : val;
+}
+
+void gpio_set_value(unsigned gpio, int value)
+{
+	u32 mask;
+	struct altera_pio *pio;
+
+	pio = altera_pio_get_and_mask(gpio, &mask);
+	if (!pio)
+		return;
+	if (pio->iot == 'i')
+		return;
+
+	value = (pio->negmask & mask) ? !value : value;
+	if (value)
+		pio->sh_data |= mask;
+	else
+		pio->sh_data &= ~mask;
+	writel(pio->sh_data, pio->base + ALTERA_PIO_DATA);
+	return;
+}
+
+int gpio_is_valid(int number)
+{
+	int gidx = altera_pio_gidx(number);
+
+	if (gidx < 0)
+		return 1;
+	return 0;
+}