ppc: Remove MPC8572DS board

This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI.  The
deadline for this conversion was the v2019.07 release.  The use of CONFIG_AHCI
requires CONFIG_DM.  The deadline for this conversion was v2020.01.  Remove
this board.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

10 files changed, 0 insertions, 757 deletions

diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
index 04e04a6358..114b7ba8f9 100644
--- a/board/freescale/common/Makefile
+++ b/board/freescale/common/Makefile
@@ -48,7 +48,6 @@ obj-$(CONFIG_TARGET_MPC8548CDS)	+= cds_pci_ft.o
 obj-$(CONFIG_TARGET_MPC8555CDS)	+= cds_pci_ft.o
 
 obj-$(CONFIG_TARGET_MPC8536DS)	+= ics307_clk.o
-obj-$(CONFIG_TARGET_MPC8572DS)	+= ics307_clk.o
 obj-$(CONFIG_TARGET_P1022DS)		+= ics307_clk.o
 obj-$(CONFIG_P2020DS)		+= ics307_clk.o
 obj-$(CONFIG_TARGET_P3041DS)		+= ics307_clk.o
diff --git a/board/freescale/common/pixis.h b/board/freescale/common/pixis.h
index f468e6cc93..7b1c973520 100644
--- a/board/freescale/common/pixis.h
+++ b/board/freescale/common/pixis.h
@@ -45,35 +45,6 @@ typedef struct pixis {
 	u8 res2[4];
 } __attribute__ ((packed)) pixis_t;
 
-#elif defined(CONFIG_TARGET_MPC8572DS)
-typedef struct pixis {
-	u8 id;
-	u8 ver;
-	u8 pver;
-	u8 csr;
-	u8 rst;
-	u8 pwr1;
-	u8 aux1;
-	u8 spd;
-	u8 aux2;
-	u8 res[7];
-	u8 vctl;
-	u8 vstat;
-	u8 vcfgen0;
-	u8 vcfgen1;
-	u8 vcore0;
-	u8 res1;
-	u8 vboot;
-	u8 vspeed[3];
-	u8 res2[2];
-	u8 sclk[3];
-	u8 dclk[3];
-	u8 res3[2];
-	u8 watch;
-	u8 led;
-	u8 res4[25];
-} __attribute__ ((packed)) pixis_t;
-
 #elif defined(CONFIG_TARGET_MPC8610HPCD)
 typedef struct pixis {
 	u8 id;
diff --git a/board/freescale/mpc8572ds/Kconfig b/board/freescale/mpc8572ds/Kconfig
deleted file mode 100644
index 38132cf3fe..0000000000
--- a/board/freescale/mpc8572ds/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_MPC8572DS
-
-config SYS_BOARD
-	default "mpc8572ds"
-
-config SYS_VENDOR
-	default "freescale"
-
-config SYS_CONFIG_NAME
-	default "MPC8572DS"
-
-endif
diff --git a/board/freescale/mpc8572ds/MAINTAINERS b/board/freescale/mpc8572ds/MAINTAINERS
deleted file mode 100644
index d7e9b1f41f..0000000000
--- a/board/freescale/mpc8572ds/MAINTAINERS
+++ /dev/null
@@ -1,7 +0,0 @@
-MPC8572DS BOARD
-M:	Priyanka Jain <priyanka.jain@nxp.com>
-S:	Maintained
-F:	board/freescale/mpc8572ds/
-F:	include/configs/MPC8572DS.h
-F:	configs/MPC8572DS_defconfig
-F:	configs/MPC8572DS_36BIT_defconfig
diff --git a/board/freescale/mpc8572ds/Makefile b/board/freescale/mpc8572ds/Makefile
deleted file mode 100644
index 5318e3be72..0000000000
--- a/board/freescale/mpc8572ds/Makefile
+++ /dev/null
@@ -1,10 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright 2007 Freescale Semiconductor, Inc.
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-
-obj-y	+= mpc8572ds.o
-obj-y	+= ddr.o
-obj-y	+= law.o
-obj-y	+= tlb.o
diff --git a/board/freescale/mpc8572ds/README b/board/freescale/mpc8572ds/README
deleted file mode 100644
index f1ffdd1730..0000000000
--- a/board/freescale/mpc8572ds/README
+++ /dev/null
@@ -1,166 +0,0 @@
-Overview
---------
-MPC8572DS is a high-performance computing, evaluation and development platform
-supporting the mpc8572 PowerTM processor.
-
-Building U-Boot
------------
-	make MPC8572DS_config
-	make
-
-Flash Banks
------------
-MPC8572DS board has two flash banks. They are both present on boot, but their
-locations can be swapped using the dip-switch SW9[1:2].
-
-Booting is always from the boot bank at 0xec00_0000.
-
-
-Memory Map
-----------
-
-0xe800_0000 - 0xebff_ffff	Alternate bank		64MB
-0xec00_0000 - 0xefff_ffff	Boot bank		64MB
-
-0xebf8_0000 - 0xebff_ffff	Alternate U-Boot address	512KB
-0xeff8_0000 - 0xefff_ffff	Boot U-Boot address		512KB
-
-
-Flashing Images
----------------
-
-To place a new U-Boot image in the alternate flash bank and then reset with that
- new image temporarily, use this:
-
-	tftp 1000000 u-boot.bin
-	erase ebf80000 ebffffff
-	cp.b 1000000 ebf80000 80000
-	pixis_reset altbank
-
-
-To program the image in the boot flash bank:
-
-	tftp 1000000 u-boot.bin
-	protect off all
-	erase eff80000 ffffffff
-	cp.b 1000000 eff80000 80000
-
-
-The pixis_reset command
------------------------
-The command - "pixis_reset", is introduced to reset mpc8572ds board
-using the FPGA sequencer.  When the board restarts, it has the option
-of using either the current or alternate flash bank as the boot
-image, with or without the watchdog timer enabled, and finally with
-or without frequency changes.
-
-Usage is;
-
-	pixis_reset
-	pixis_reset altbank
-	pixis_reset altbank wd
-	pixis_reset altbank cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
-	pixis_reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
-
-Examples:
-
-	/* reset to current bank, like "reset" command */
-	pixis_reset
-
-	/* reset board but use the to alternate flash bank */
-	pixis_reset altbank
-
-
-Using the Device Tree Source File
----------------------------------
-To create the DTB (Device Tree Binary) image file,
-use a command similar to this:
-
-	dtc -b 0 -f -I dts -O dtb mpc8572ds.dts > mpc8572ds.dtb
-
-Likely, that .dts file will come from here;
-
-	linux-2.6/arch/powerpc/boot/dts/mpc8572ds.dts
-
-
-Booting Linux
--------------
-
-Place a linux uImage in the TFTP disk area.
-
-	tftp 1000000 uImage.8572
-	tftp c00000 mpc8572ds.dtb
-	bootm 1000000 - c00000
-
-
-Implementing AMP(Asymmetric MultiProcessing)
--------------
-1. Build kernel image for core0:
-
-	a. $ make 85xx/mpc8572_ds_defconfig
-
-	b. $ make menuconfig
-	   - un-select "Processor support"->"Symetric multi-processing support"
-
-	c. $ make uImage
-
-	d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core0
-
-2. Build kernel image for core1:
-
-	a. $ make 85xx/mpc8572_ds_defconfig
-
-	b. $ make menuconfig
-	   - Un-select "Processor support"->"Symetric multi-processing support"
-	   - Select "Advanced setup" -> " Prompt for advanced kernel
-	     configuration options"
-		- Select "Set physical address where the kernel is loaded" and
-		  set it to 0x20000000, assuming core1 will start from 512MB.
-		- Select "Set custom page offset address"
-		- Select "Set custom kernel base address"
-		- Select "Set maximum low memory"
-	   - "Exit" and save the selection.
-
-	c. $ make uImage
-
-	d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core1
-
-3. Create dtb for core0:
-
-	$ dtc -I dts -O dtb -f -b 0 arch/powerpc/boot/dts/mpc8572ds_core0.dts > /tftpboot/mpc8572ds_core0.dtb
-
-4. Create dtb for core1:
-
-	$ dtc -I dts -O dtb -f -b 1 arch/powerpc/boot/dts/mpc8572ds_core1.dts > /tftpboot/mpc8572ds_core1.dtb
-
-5. Bring up two cores separately:
-
-	a. Power on the board, under U-Boot prompt:
-		=> setenv <serverip>
-		=> setenv <ipaddr>
-		=> setenv bootargs root=/dev/ram rw console=ttyS0,115200
-	b. Bring up core1's kernel first:
-		=> setenv bootm_low 0x20000000
-		=> setenv bootm_size 0x10000000
-		=> tftp 21000000 8572/uImage.core1
-		=> tftp 22000000 8572/ramdiskfile
-		=> tftp 20c00000 8572/mpc8572ds_core1.dtb
-		=> interrupts off
-		=> bootm start 21000000 22000000 20c00000
-		=> bootm loados
-		=> bootm ramdisk
-		=> bootm fdt
-		=> fdt boardsetup
-		=> fdt chosen $initrd_start $initrd_end
-		=> bootm prep
-		=> cpu 1 release $bootm_low - $fdtaddr -
-	c. Bring up core0's kernel(on the same U-Boot console):
-		=> setenv bootm_low 0
-		=> setenv bootm_size 0x20000000
-		=> tftp 1000000 8572/uImage.core0
-		=> tftp 2000000 8572/ramdiskfile
-		=> tftp c00000 8572/mpc8572ds_core0.dtb
-		=> bootm 1000000 2000000 c00000
-
-Please note only core0 will run U-Boot, core1 starts kernel directly after
-"cpu release" command is issued.
diff --git a/board/freescale/mpc8572ds/ddr.c b/board/freescale/mpc8572ds/ddr.c
deleted file mode 100644
index 11ca08d1a0..0000000000
--- a/board/freescale/mpc8572ds/ddr.c
+++ /dev/null
@@ -1,166 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-
-struct board_specific_parameters {
-	u32 n_ranks;
-	u32 datarate_mhz_high;
-	u32 clk_adjust;
-	u32 cpo;
-	u32 write_data_delay;
-	u32 force_2t;
-};
-
-/*
- * This table contains all valid speeds we want to override with board
- * specific parameters. datarate_mhz_high values need to be in ascending order
- * for each n_ranks group.
- *
- * For DDR2 DIMM, all combinations of clk_adjust and write_data_delay have been
- * tested. For RDIMM, clk_adjust = 4 and write_data_delay = 3 is optimized for
- * all clocks from 400MT/s to 800MT/s, verified with Kingston KVR800D2D8P6/2G.
- * For UDIMM, clk_adjust = 8 and write_delay = 5 is optimized for all clocks
- * from 400MT/s to 800MT/s, verified with Micron MT18HTF25672AY-800E1.
- *
- * CPO value doesn't matter if workaround for errata 111 and 134 enabled.
- */
-static const struct board_specific_parameters udimm0[] = {
-	/*
-	 * memory controller 0
-	 *   num|  hi|  clk| cpo|wrdata|2T
-	 * ranks| mhz|adjst|    | delay|
-	 */
-	{2,  333,    8,   7,    5,  0},
-	{2,  400,    8,   9,    5,  0},
-	{2,  549,    8,  11,    5,  0},
-	{2,  680,    8,  10,    5,  0},
-	{2,  850,    8,  12,    5,  1},
-	{1,  333,    6,   7,    3,  0},
-	{1,  400,    6,   9,    3,  0},
-	{1,  549,    6,  11,    3,  0},
-	{1,  680,    1,  10,    5,  0},
-	{1,  850,    1,  12,    5,  0},
-	{}
-};
-
-static const struct board_specific_parameters udimm1[] = {
-	/*
-	 * memory controller 1
-	 *   num|  hi|  clk| cpo|wrdata|2T
-	 * ranks| mhz|adjst|    | delay|
-	 */
-	{2,  333,    8,  7,    5,  0},
-	{2,  400,    8,  9,    5,  0},
-	{2,  549,    8, 11,    5,  0},
-	{2,  680,    8, 11,    5,  0},
-	{2,  850,    8, 13,    5,  1},
-	{1,  333,    6,  7,    3,  0},
-	{1,  400,    6,  9,    3,  0},
-	{1,  549,    6, 11,    3,  0},
-	{1,  680,    1, 11,    6,  0},
-	{1,  850,    1, 13,    6,  0},
-	{}
-};
-
-static const struct board_specific_parameters *udimms[] = {
-	udimm0,
-	udimm1,
-};
-
-static const struct board_specific_parameters rdimm0[] = {
-	/*
-	 * memory controller 0
-	 *   num|  hi|  clk| cpo|wrdata|2T
-	 * ranks| mhz|adjst|    | delay|
-	 */
-	{2,  333,    4,   7,    3,  0},
-	{2,  400,    4,   9,    3,  0},
-	{2,  549,    4,  11,    3,  0},
-	{2,  680,    4,  10,    3,  0},
-	{2,  850,    4,  12,    3,  1},
-	{}
-};
-
-static const struct board_specific_parameters rdimm1[] = {
-	/*
-	 * memory controller 1
-	 *   num|  hi|  clk| cpo|wrdata|2T
-	 * ranks| mhz|adjst|    | delay|
-	 */
-	{2,  333,     4,  7,    3,  0},
-	{2,  400,     4,  9,    3,  0},
-	{2,  549,     4, 11,    3,  0},
-	{2,  680,     4, 11,    3,  0},
-	{2,  850,     4, 13,    3,  1},
-	{}
-};
-
-static const struct board_specific_parameters *rdimms[] = {
-	rdimm0,
-	rdimm1,
-};
-
-void fsl_ddr_board_options(memctl_options_t *popts,
-				dimm_params_t *pdimm,
-				unsigned int ctrl_num)
-{
-	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
-	ulong ddr_freq;
-
-	if (ctrl_num > 1) {
-		printf("Wrong parameter for controller number %d", ctrl_num);
-		return;
-	}
-	if (!pdimm->n_ranks)
-		return;
-
-	if (popts->registered_dimm_en)
-		pbsp = rdimms[ctrl_num];
-	else
-		pbsp = udimms[ctrl_num];
-
-	/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
-	 * freqency and n_banks specified in board_specific_parameters table.
-	 */
-	ddr_freq = get_ddr_freq(0) / 1000000;
-	while (pbsp->datarate_mhz_high) {
-		if (pbsp->n_ranks == pdimm->n_ranks) {
-			if (ddr_freq <= pbsp->datarate_mhz_high) {
-				popts->clk_adjust = pbsp->clk_adjust;
-				popts->cpo_override = pbsp->cpo;
-				popts->write_data_delay =
-					pbsp->write_data_delay;
-				popts->twot_en = pbsp->force_2t;
-				goto found;
-			}
-			pbsp_highest = pbsp;
-		}
-		pbsp++;
-	}
-
-	if (pbsp_highest) {
-		printf("Error: board specific timing not found "
-			"for data rate %lu MT/s!\n"
-			"Trying to use the highest speed (%u) parameters\n",
-			ddr_freq, pbsp_highest->datarate_mhz_high);
-		popts->clk_adjust = pbsp->clk_adjust;
-		popts->cpo_override = pbsp->cpo;
-		popts->write_data_delay = pbsp->write_data_delay;
-		popts->twot_en = pbsp->force_2t;
-	} else {
-		panic("DIMM is not supported by this board");
-	}
-
-found:
-	/*
-	 * Factors to consider for half-strength driver enable:
-	 *	- number of DIMMs installed
-	 */
-	popts->half_strength_driver_enable = 0;
-}
diff --git a/board/freescale/mpc8572ds/law.c b/board/freescale/mpc8572ds/law.c
deleted file mode 100644
index 10d1572c5d..0000000000
--- a/board/freescale/mpc8572ds/law.c
+++ /dev/null
@@ -1,19 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008, 2010 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-struct law_entry law_table[] = {
-	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
-	SET_LAW(PIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_LBC),
-	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/mpc8572ds/mpc8572ds.c b/board/freescale/mpc8572ds/mpc8572ds.c
deleted file mode 100644
index 97e73533ab..0000000000
--- a/board/freescale/mpc8572ds/mpc8572ds.c
+++ /dev/null
@@ -1,260 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2007-2011 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <command.h>
-#include <env.h>
-#include <image.h>
-#include <init.h>
-#include <log.h>
-#include <net.h>
-#include <pci.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/cache.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_pci.h>
-#include <fsl_ddr_sdram.h>
-#include <asm/io.h>
-#include <asm/fsl_serdes.h>
-#include <miiphy.h>
-#include <linux/delay.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <tsec.h>
-#include <fsl_mdio.h>
-#include <netdev.h>
-
-#include "../common/sgmii_riser.h"
-
-int checkboard (void)
-{
-	u8 vboot;
-	u8 *pixis_base = (u8 *)PIXIS_BASE;
-
-	printf("Board: MPC8572DS Sys ID: 0x%02x, "
-		"Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
-		in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER),
-		in_8(pixis_base + PIXIS_PVER));
-
-	vboot = in_8(pixis_base + PIXIS_VBOOT);
-	switch ((vboot & PIXIS_VBOOT_LBMAP) >> 6) {
-		case PIXIS_VBOOT_LBMAP_NOR0:
-			puts ("vBank: 0\n");
-			break;
-		case PIXIS_VBOOT_LBMAP_PJET:
-			puts ("Promjet\n");
-			break;
-		case PIXIS_VBOOT_LBMAP_NAND:
-			puts ("NAND\n");
-			break;
-		case PIXIS_VBOOT_LBMAP_NOR1:
-			puts ("vBank: 1\n");
-			break;
-	}
-
-	return 0;
-}
-
-
-#if !defined(CONFIG_SPD_EEPROM)
-/*
- * Fixed sdram init -- doesn't use serial presence detect.
- */
-
-phys_size_t fixed_sdram (void)
-{
-	volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
-	struct ccsr_ddr __iomem *ddr = &immap->im_ddr;
-	uint d_init;
-
-	ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
-	ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
-
-	ddr->timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
-	ddr->timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
-	ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
-	ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
-	ddr->sdram_mode = CONFIG_SYS_DDR_MODE_1;
-	ddr->sdram_mode_2 = CONFIG_SYS_DDR_MODE_2;
-	ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL;
-	ddr->sdram_data_init = CONFIG_SYS_DDR_DATA_INIT;
-	ddr->sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL;
-	ddr->sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL2;
-
-#if defined (CONFIG_DDR_ECC)
-	ddr->err_int_en = CONFIG_SYS_DDR_ERR_INT_EN;
-	ddr->err_disable = CONFIG_SYS_DDR_ERR_DIS;
-	ddr->err_sbe = CONFIG_SYS_DDR_SBE;
-#endif
-	asm("sync;isync");
-
-	udelay(500);
-
-	ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL;
-
-#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
-	d_init = 1;
-	debug("DDR - 1st controller: memory initializing\n");
-	/*
-	 * Poll until memory is initialized.
-	 * 512 Meg at 400 might hit this 200 times or so.
-	 */
-	while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0) {
-		udelay(1000);
-	}
-	debug("DDR: memory initialized\n\n");
-	asm("sync; isync");
-	udelay(500);
-#endif
-
-	return 512 * 1024 * 1024;
-}
-
-#endif
-
-#ifdef CONFIG_PCI
-void pci_init_board(void)
-{
-	struct pci_controller *hose;
-
-	fsl_pcie_init_board(0);
-
-	hose = find_hose_by_cfg_addr((void *)(CONFIG_SYS_PCIE3_ADDR));
-
-	if (hose) {
-		u32 temp32;
-		u8 uli_busno = hose->first_busno + 2;
-
-		/*
-		 * Activate ULI1575 legacy chip by performing a fake
-		 * memory access.  Needed to make ULI RTC work.
-		 * Device 1d has the first on-board memory BAR.
-		 */
-		pci_hose_read_config_dword(hose, PCI_BDF(uli_busno, 0x1d, 0),
-				PCI_BASE_ADDRESS_1, &temp32);
-
-		if (temp32 >= CONFIG_SYS_PCIE3_MEM_BUS) {
-			void *p = pci_mem_to_virt(PCI_BDF(uli_busno, 0x1d, 0),
-					temp32, 4, 0);
-			debug(" uli1572 read to %p\n", p);
-			in_be32(p);
-		}
-	}
-}
-#endif
-
-int board_early_init_r(void)
-{
-	const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
-	int flash_esel = find_tlb_idx((void *)flashbase, 1);
-
-	/*
-	 * Remap Boot flash + PROMJET region to caching-inhibited
-	 * so that flash can be erased properly.
-	 */
-
-	/* Flush d-cache and invalidate i-cache of any FLASH data */
-	flush_dcache();
-	invalidate_icache();
-
-	if (flash_esel == -1) {
-		/* very unlikely unless something is messed up */
-		puts("Error: Could not find TLB for FLASH BASE\n");
-		flash_esel = 2; /* give our best effort to continue */
-	} else {
-		/* invalidate existing TLB entry for flash + promjet */
-		disable_tlb(flash_esel);
-	}
-
-	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,	/* tlb, epn, rpn */
-			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,	/* perms, wimge */
-			0, flash_esel, BOOKE_PAGESZ_256M, 1);	/* ts, esel, tsize, iprot */
-
-	return 0;
-}
-
-int board_eth_init(struct bd_info *bis)
-{
-#ifdef CONFIG_TSEC_ENET
-	struct fsl_pq_mdio_info mdio_info;
-	struct tsec_info_struct tsec_info[4];
-	int num = 0;
-
-#ifdef CONFIG_TSEC1
-	SET_STD_TSEC_INFO(tsec_info[num], 1);
-	if (is_serdes_configured(SGMII_TSEC1)) {
-		puts("eTSEC1 is in sgmii mode.\n");
-		tsec_info[num].flags |= TSEC_SGMII;
-	}
-	num++;
-#endif
-#ifdef CONFIG_TSEC2
-	SET_STD_TSEC_INFO(tsec_info[num], 2);
-	if (is_serdes_configured(SGMII_TSEC2)) {
-		puts("eTSEC2 is in sgmii mode.\n");
-		tsec_info[num].flags |= TSEC_SGMII;
-	}
-	num++;
-#endif
-#ifdef CONFIG_TSEC3
-	SET_STD_TSEC_INFO(tsec_info[num], 3);
-	if (is_serdes_configured(SGMII_TSEC3)) {
-		puts("eTSEC3 is in sgmii mode.\n");
-		tsec_info[num].flags |= TSEC_SGMII;
-	}
-	num++;
-#endif
-#ifdef CONFIG_TSEC4
-	SET_STD_TSEC_INFO(tsec_info[num], 4);
-	if (is_serdes_configured(SGMII_TSEC4)) {
-		puts("eTSEC4 is in sgmii mode.\n");
-		tsec_info[num].flags |= TSEC_SGMII;
-	}
-	num++;
-#endif
-
-	if (!num) {
-		printf("No TSECs initialized\n");
-
-		return 0;
-	}
-
-#ifdef CONFIG_FSL_SGMII_RISER
-	fsl_sgmii_riser_init(tsec_info, num);
-#endif
-
-	mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
-	mdio_info.name = DEFAULT_MII_NAME;
-	fsl_pq_mdio_init(bis, &mdio_info);
-
-	tsec_eth_init(bis, tsec_info, num);
-#endif
-
-	return pci_eth_init(bis);
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
-	phys_addr_t base;
-	phys_size_t size;
-
-	ft_cpu_setup(blob, bd);
-
-	base = env_get_bootm_low();
-	size = env_get_bootm_size();
-
-	fdt_fixup_memory(blob, (u64)base, (u64)size);
-
-	FT_FSL_PCI_SETUP;
-
-#ifdef CONFIG_FSL_SGMII_RISER
-	fsl_sgmii_riser_fdt_fixup(blob);
-#endif
-
-	return 0;
-}
-#endif
diff --git a/board/freescale/mpc8572ds/tlb.c b/board/freescale/mpc8572ds/tlb.c
deleted file mode 100644
index 99b136b042..0000000000
--- a/board/freescale/mpc8572ds/tlb.c
+++ /dev/null
@@ -1,87 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008-2010 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
-	/* TLB 0 - for temp stack in cache */
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-
-	/* TLB 1 */
-	/* *I*** - Covers boot page */
-	SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 0, BOOKE_PAGESZ_4K, 1),
-
-	/* *I*G* - CCSRBAR */
-	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 1, BOOKE_PAGESZ_1M, 1),
-
-	/* W**G* - Flash/promjet, localbus */
-	/* This will be changed to *I*G* after relocation to RAM. */
-	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
-		      MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
-		      0, 2, BOOKE_PAGESZ_256M, 1),
-
-#ifndef CONFIG_NAND_SPL
-	/* *I*G* - PCI */
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 3, BOOKE_PAGESZ_1G, 1),
-
-	/* *I*G* - PCI */
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x40000000, CONFIG_SYS_PCIE3_MEM_PHYS + 0x40000000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 4, BOOKE_PAGESZ_256M, 1),
-
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x50000000, CONFIG_SYS_PCIE3_MEM_PHYS + 0x50000000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 5, BOOKE_PAGESZ_256M, 1),
-
-	/* *I*G* - PCI I/O */
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_IO_VIRT, CONFIG_SYS_PCIE3_IO_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 6, BOOKE_PAGESZ_256K, 1),
-#endif
-
-	/* *I*G - NAND */
-	SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 7, BOOKE_PAGESZ_1M, 1),
-
-	SET_TLB_ENTRY(1, PIXIS_BASE, PIXIS_BASE_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 8, BOOKE_PAGESZ_4K, 1),
-
-#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L2_ADDR)
-	/* *I*G - L2SRAM */
-	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR,
-			CONFIG_SYS_INIT_L2_ADDR_PHYS,
-			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-			0, 9, BOOKE_PAGESZ_256K, 1),
-	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + 0x40000,
-			CONFIG_SYS_INIT_L2_ADDR_PHYS + 0x40000,
-			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-			0, 10, BOOKE_PAGESZ_256K, 1),
-#endif
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);