powerpc, 5xxx, 512x: remove support for mpc5xxx and mpc512x

There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.

Signed-off-by: Heiko Schocher <hs@denx.de>

1 files changed, 0 insertions, 402 deletions

diff --git a/board/cm5200/cmd_cm5200.c b/board/cm5200/cmd_cm5200.c
deleted file mode 100644
index 60097dc8c7..0000000000
--- a/board/cm5200/cmd_cm5200.c
+++ /dev/null
@@ -1,402 +0,0 @@
-/*
- * (C) Copyright 2007 Markus Kappeler <markus.kappeler@objectxp.com>
- *
- * Adapted for U-Boot 1.2 by Piotr Kruszynski <ppk@semihalf.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <i2c.h>
-#include <usb.h>
-
-#ifdef CONFIG_CMD_BSP
-
-static int do_usb_test(char * const argv[])
-{
-	int i;
-	static int usb_stor_curr_dev = -1; /* current device */
-
-	printf("Starting USB Test\n"
-		"Please insert USB Memmory Stick\n\n"
-		"Please press any key to start\n\n");
-	getc();
-
-	usb_stop();
-	printf("(Re)start USB...\n");
-	i = usb_init();
-#ifdef CONFIG_USB_STORAGE
-		/* try to recognize storage devices immediately */
-		if (i >= 0)
-			usb_stor_curr_dev = usb_stor_scan(1);
-#endif /* CONFIG_USB_STORAGE */
-	if (usb_stor_curr_dev >= 0)
-		printf("Found USB Storage Dev continue with Test...\n");
-	else {
-		printf("No USB Storage Device detected.. Stop Test\n");
-		return 1;
-	}
-
-	usb_stor_info();
-
-	printf("stopping USB..\n");
-	usb_stop();
-
-	return 0;
-}
-
-static int do_led_test(char * const argv[])
-{
-	int i = 0;
-	struct mpc5xxx_gpt_0_7 *gpt = (struct mpc5xxx_gpt_0_7 *)MPC5XXX_GPT;
-
-	printf("Starting LED Test\n"
-		"Please set Switch S500 all off\n\n"
-		"Please press any key to start\n\n");
-	getc();
-
-	/* configure timer 2-3 for simple GPIO output High */
-	gpt->gpt2.emsr |= 0x00000034;
-	gpt->gpt3.emsr |= 0x00000034;
-
-	(*(vu_long *)MPC5XXX_WU_GPIO_ENABLE) |= 0x80000000;
-	(*(vu_long *)MPC5XXX_WU_GPIO_DIR) |= 0x80000000;
-	printf("Please press any key to stop\n\n");
-	while (!tstc()) {
-		if (i == 1) {
-			(*(vu_long *)MPC5XXX_WU_GPIO_DATA_O) |= 0x80000000;
-			gpt->gpt2.emsr &= ~0x00000010;
-			gpt->gpt3.emsr &= ~0x00000010;
-		} else if (i == 2) {
-			(*(vu_long *)MPC5XXX_WU_GPIO_DATA_O) &= ~0x80000000;
-			gpt->gpt2.emsr &= ~0x00000010;
-			gpt->gpt3.emsr |= 0x00000010;
-		} else if (i >= 3) {
-			(*(vu_long *)MPC5XXX_WU_GPIO_DATA_O) &= ~0x80000000;
-			gpt->gpt3.emsr &= ~0x00000010;
-			gpt->gpt2.emsr |= 0x00000010;
-			i = 0;
-		}
-		i++;
-		udelay(200000);
-	}
-	getc();
-
-	(*(vu_long *)MPC5XXX_WU_GPIO_DATA_O) |= 0x80000000;
-	gpt->gpt2.emsr |= 0x00000010;
-	gpt->gpt3.emsr |= 0x00000010;
-
-	return 0;
-}
-
-static int do_rs232_test(char * const argv[])
-{
-	int error_status = 0;
-	struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
-	struct mpc5xxx_psc *psc1 = (struct mpc5xxx_psc *)MPC5XXX_PSC1;
-
-	/* Configure PSC 2-3-6 as GPIO */
-	gpio->port_config &= 0xFF0FF80F;
-
-	switch (simple_strtoul(argv[2], NULL, 10)) {
-	case 1:
-		/* check RTS <-> CTS loop */
-		/* set rts to 0 */
-		printf("Uart 1 test: RX TX tested by using U-Boot\n"
-			"Please connect RTS with CTS on Uart1 plug\n\n"
-			"Press any key to start\n\n");
-		getc();
-
-		psc1->op1 |= 0x01;
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		/* check status at cts */
-		if ((psc1->ip & 0x01) != 0) {
-			error_status = 3;
-			printf("%s: failure at rs232_1, cts status is %d "
-				"(should be 0)\n",
-				__FUNCTION__, (psc1->ip & 0x01));
-		}
-
-		/* set rts to 1 */
-		psc1->op0 |= 0x01;
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		/* check status at cts */
-		if ((psc1->ip & 0x01) != 1) {
-			error_status = 3;
-			printf("%s: failure at rs232_1, cts status is %d "
-				"(should be 1)\n",
-				__FUNCTION__, (psc1->ip & 0x01));
-		}
-		break;
-	case 2:
-		/* set PSC2_0, PSC2_2 as output and PSC2_1, PSC2_3 as input */
-		printf("Uart 2 test: Please use RS232 Loopback plug on UART2\n"
-			"\nPress any key to start\n\n");
-		getc();
-
-		gpio->simple_gpioe &= ~(0x000000F0);
-		gpio->simple_gpioe |= 0x000000F0;
-		gpio->simple_ddr &= ~(0x000000F0);
-		gpio->simple_ddr |= 0x00000050;
-
-		/* check TXD <-> RXD loop */
-		/* set TXD to 1 */
-		gpio->simple_dvo |= (1 << 4);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000020) != 0x00000020) {
-			error_status = 2;
-			printf("%s: failure at rs232_2, rxd status is %d "
-				"(should be 1)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000020) >> 5);
-		}
-
-		/* set TXD to 0 */
-		gpio->simple_dvo &= ~(1 << 4);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000020) != 0x00000000) {
-			error_status = 2;
-			printf("%s: failure at rs232_2, rxd status is %d "
-				"(should be 0)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000020) >> 5);
-		}
-
-		/* check RTS <-> CTS loop */
-		/* set RTS to 1 */
-		gpio->simple_dvo |= (1 << 6);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000080) != 0x00000080) {
-			error_status = 3;
-			printf("%s: failure at rs232_2, cts status is %d "
-				"(should be 1)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000080) >> 7);
-		}
-
-		/* set RTS to 0 */
-		gpio->simple_dvo &= ~(1 << 6);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000080) != 0x00000000) {
-			error_status = 3;
-			printf("%s: failure at rs232_2, cts status is %d "
-				"(should be 0)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000080) >> 7);
-		}
-		break;
-	case 3:
-		/* set PSC3_0, PSC3_2 as output and PSC3_1, PSC3_3 as input */
-		printf("Uart 3 test: Please use RS232 Loopback plug on UART2\n"
-			"\nPress any key to start\n\n");
-		getc();
-
-		gpio->simple_gpioe &= ~(0x00000F00);
-		gpio->simple_gpioe |= 0x00000F00;
-
-		gpio->simple_ddr &= ~(0x00000F00);
-		gpio->simple_ddr |= 0x00000500;
-
-		/* check TXD <-> RXD loop */
-		/* set TXD to 1 */
-		gpio->simple_dvo |= (1 << 8);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000200) != 0x00000200) {
-			error_status = 2;
-			printf("%s: failure at rs232_3, rxd status is %d "
-				"(should be 1)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000200) >> 9);
-		}
-
-		/* set TXD to 0 */
-		gpio->simple_dvo &= ~(1 << 8);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000200) != 0x00000000) {
-			error_status = 2;
-			printf("%s: failure at rs232_3, rxd status is %d "
-				"(should be 0)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000200) >> 9);
-		}
-
-		/* check RTS <-> CTS loop */
-		/* set RTS to 1 */
-		gpio->simple_dvo |= (1 << 10);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000800) != 0x00000800) {
-			error_status = 3;
-			printf("%s: failure at rs232_3, cts status is %d "
-				"(should be 1)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000800) >> 11);
-		}
-
-		/* set RTS to 0 */
-		gpio->simple_dvo &= ~(1 << 10);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000800) != 0x00000000) {
-			error_status = 3;
-			printf("%s: failure at rs232_3, cts status is %d "
-				"(should be 0)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000800) >> 11);
-		}
-		break;
-	case 4:
-		/* set PSC6_2, PSC6_3 as output and PSC6_0, PSC6_1 as input */
-		printf("Uart 4 test: Please use RS232 Loopback plug on UART2\n"
-			"\nPress any key to start\n\n");
-		getc();
-
-		gpio->simple_gpioe &= ~(0xF0000000);
-		gpio->simple_gpioe |= 0x30000000;
-
-		gpio->simple_ddr &= ~(0xf0000000);
-		gpio->simple_ddr |= 0x30000000;
-
-		(*(vu_long *)MPC5XXX_WU_GPIO_ENABLE) |= 0x30000000;
-		(*(vu_long *)MPC5XXX_WU_GPIO_DIR) &= ~(0x30000000);
-
-		/* check TXD <-> RXD loop */
-		/* set TXD to 1 */
-		gpio->simple_dvo |= (1 << 28);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if (((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) & 0x10000000) !=
-				0x10000000) {
-			error_status = 2;
-			printf("%s: failure at rs232_4, rxd status is %lu "
-				"(should be 1)\n", __FUNCTION__,
-				((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) &
-					0x10000000) >> 28);
-		}
-
-		/* set TXD to 0 */
-		gpio->simple_dvo &= ~(1 << 28);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if (((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) & 0x10000000) !=
-				0x00000000) {
-			error_status = 2;
-			printf("%s: failure at rs232_4, rxd status is %lu "
-				"(should be 0)\n", __FUNCTION__,
-				((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) &
-					0x10000000) >> 28);
-		}
-
-		/* check RTS <-> CTS loop */
-		/* set RTS to 1 */
-		gpio->simple_dvo |= (1 << 29);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if (((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) & 0x20000000) !=
-				0x20000000) {
-			error_status = 3;
-			printf("%s: failure at rs232_4, cts status is %lu "
-				"(should be 1)\n", __FUNCTION__,
-				((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) &
-					0x20000000) >> 29);
-		}
-
-		/* set RTS to 0 */
-		gpio->simple_dvo &= ~(1 << 29);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if (((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) & 0x20000000) !=
-				0x00000000) {
-			error_status = 3;
-			printf("%s: failure at rs232_4, cts status is %lu "
-				"(should be 0)\n", __FUNCTION__,
-				((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) &
-					0x20000000) >> 29);
-		}
-		break;
-	default:
-		printf("%s: invalid rs232 number %s\n", __FUNCTION__, argv[2]);
-		error_status = 1;
-		break;
-	}
-	gpio->port_config |= (CONFIG_SYS_GPS_PORT_CONFIG & 0xFF0FF80F);
-
-	return error_status;
-}
-
-static int cmd_fkt(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-	int rcode = -1;
-
-	switch (argc) {
-	case 2:
-		if (strncmp(argv[1], "led", 3) == 0)
-			rcode = do_led_test(argv);
-		else if (strncmp(argv[1], "usb", 3) == 0)
-			rcode = do_usb_test(argv);
-		break;
-	case 3:
-		if (strncmp(argv[1], "rs232", 3) == 0)
-			rcode = do_rs232_test(argv);
-		break;
-	}
-
-	switch (rcode) {
-	case -1:
-		printf("Usage:\n"
-			"fkt { i2c | led | usb }\n"
-			"fkt rs232 number\n");
-		rcode = 1;
-		break;
-	case 0:
-		printf("Test passed\n");
-		break;
-	default:
-		printf("Test failed with code: %d\n", rcode);
-	}
-
-	return rcode;
-}
-
-U_BOOT_CMD(
-	fkt,	4,	1,	cmd_fkt,
-	"Function test routines",
-	"i2c\n"
-	"     - Test I2C communication\n"
-	"fkt led\n"
-	"     - Test LEDs\n"
-	"fkt rs232 number\n"
-	"     - Test RS232 (loopback plug(s) for RS232 required)\n"
-	"fkt usb\n"
-	"     - Test USB communication"
-);
-#endif /* CONFIG_CMD_BSP */