board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support

Add initial support PHYTEC phyCORE-i.MX8MP SOM.

    Supported features:
     - 2GB LPDDR4 RAM
     - eMMC
     - external SD
     - debug UART2
     - watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

5 files changed, 576 insertions, 0 deletions

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index ebdda1a8f2..c0b4d9d275 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -786,6 +786,7 @@ dtb-$(CONFIG_ARCH_IMX8M) += \
 	imx8mm-beacon-kit.dtb \
 	imx8mq-phanbell.dtb \
 	imx8mp-evk.dtb \
+	imx8mp-phyboard-pollux-rdk.dtb \
 	imx8mq-pico-pi.dtb
 
 dtb-$(CONFIG_ARCH_IMXRT) += imxrt1050-evk.dtb \
diff --git a/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi b/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
new file mode 100644
index 0000000000..20e7f63ff9
--- /dev/null
+++ b/arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi
@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2020 PHYTEC Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@phytec.de>
+ */
+
+/ {
+	wdt-reboot {
+		compatible = "wdt-reboot";
+		wdt = <&wdog1>;
+		u-boot,dm-spl;
+	};
+};
+
+&{/soc@0} {
+	u-boot,dm-pre-reloc;
+	u-boot,dm-spl;
+};
+
+&clk {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+};
+
+&osc_32k {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+};
+
+&osc_24m {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+};
+
+&aips1 {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+};
+
+&aips2 {
+	u-boot,dm-spl;
+};
+
+&aips3 {
+	u-boot,dm-spl;
+};
+
+&iomuxc {
+	u-boot,dm-spl;
+};
+
+&reg_usdhc2_vmmc {
+	u-boot,dm-spl;
+};
+
+&pinctrl_uart2 {
+	u-boot,dm-spl;
+};
+
+&pinctrl_usdhc2_pins {
+	u-boot,dm-spl;
+};
+
+&pinctrl_usdhc2 {
+	u-boot,dm-spl;
+};
+
+&pinctrl_usdhc3 {
+	u-boot,dm-spl;
+};
+
+&gpio1 {
+	u-boot,dm-spl;
+};
+
+&gpio2 {
+	u-boot,dm-spl;
+};
+
+&gpio3 {
+	u-boot,dm-spl;
+};
+
+&gpio4 {
+	u-boot,dm-spl;
+};
+
+&gpio5 {
+	u-boot,dm-spl;
+};
+
+&uart2 {
+	u-boot,dm-spl;
+};
+
+&i2c1 {
+	u-boot,dm-spl;
+};
+
+&pmic {
+	u-boot,dm-spl;
+};
+
+&usdhc2 {
+	u-boot,dm-spl;
+};
+
+&usdhc3 {
+	u-boot,dm-spl;
+};
+
+&wdog1 {
+	u-boot,dm-spl;
+};
diff --git a/arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts b/arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts
new file mode 100644
index 0000000000..0e1a6d9533
--- /dev/null
+++ b/arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 PHYTEC Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@phytec.de>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/leds-pca9532.h>
+#include <dt-bindings/pwm/pwm.h>
+#include "imx8mp-phycore-som.dtsi"
+
+/ {
+	model = "PHYTEC phyBOARD-Pollux i.MX8MP";
+	compatible = "phytec,imx8mp-phyboard-pollux-rdk",
+		     "phytec,imx8mp-phycore-som", "fsl,imx8mp";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100>;
+		off-on-delay-us = <12000>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+		pagesize = <16>;
+	};
+
+	leds@62 {
+		compatible = "nxp,pca9533";
+		reg = <0x62>;
+
+		led1 {
+			type = <PCA9532_TYPE_LED>;
+		};
+
+		led2 {
+			type = <PCA9532_TYPE_LED>;
+		};
+
+		led3 {
+			type = <PCA9532_TYPE_LED>;
+		};
+	};
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+/* debug console */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+/* SD-Card */
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_pins>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_pins>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_pins>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c3
+			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16	0x1e3
+			MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17	0x1e3
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x41
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x49
+			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX	0x49
+		>;
+	};
+
+	pinctrl_usdhc2_pins: usdhc2-gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12	0x1c4
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK	0x190
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD	0x1d0
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d0
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d0
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d0
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d0
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK	0x194
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD	0x1d4
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d4
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d4
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d4
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d4
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK	0x196
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD	0x1d6
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d6
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d6
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d6
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d6
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
+		>;
+	};
+};
diff --git a/arch/arm/dts/imx8mp-phycore-som.dtsi b/arch/arm/dts/imx8mp-phycore-som.dtsi
new file mode 100644
index 0000000000..44a8c2337c
--- /dev/null
+++ b/arch/arm/dts/imx8mp-phycore-som.dtsi
@@ -0,0 +1,293 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 PHYTEC Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@phytec.de>
+ */
+
+#include <dt-bindings/net/ti-dp83867.h>
+#include "imx8mp.dtsi"
+
+/ {
+	model = "PHYTEC phyCORE-i.MX8MP";
+	compatible = "phytec,imx8mp-phycore-som", "fsl,imx8mp";
+
+	aliases {
+		rtc0 = &rv3028;
+		rtc1 = &snvs_rtc;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_1 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_2 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_3 {
+	cpu-supply = <&buck2>;
+};
+
+/* ethernet 1 */
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy1>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+			enet-phy-lane-no-swap;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pmic: pmic@25 {
+		reg = <0x25>;
+		compatible = "nxp,pca9450c";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			buck1: BUCK1 {
+				regulator-compatible = "BUCK1";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <2187500>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			buck2: BUCK2 {
+				regulator-compatible = "BUCK2";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <2187500>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			buck4: BUCK4 {
+				regulator-compatible = "BUCK4";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5: BUCK5 {
+				regulator-compatible = "BUCK5";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck6: BUCK6 {
+				regulator-compatible = "BUCK6";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1: LDO1 {
+				regulator-compatible = "LDO1";
+				regulator-min-microvolt = <1600000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2: LDO2 {
+				regulator-compatible = "LDO2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3: LDO3 {
+				regulator-compatible = "LDO3";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4: LDO4 {
+				regulator-compatible = "LDO4";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo5: LDO5 {
+				regulator-compatible = "LDO5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c32";
+		reg = <0x51>;
+		pagesize = <32>;
+	};
+
+	rv3028: rtc@52 {
+		compatible = "microcrystal,rv3028";
+		reg = <0x52>;
+		trickle-resistor-ohms = <3000>;
+	};
+};
+
+/* eMMC */
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x3
+			MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x3
+			MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0		0x91
+			MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1		0x91
+			MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2		0x91
+			MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3		0x91
+			MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x91
+			MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x91
+			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0		0x1f
+			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1		0x1f
+			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2		0x1f
+			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3		0x1f
+			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x1f
+			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC		0x1f
+			MX8MP_IOMUXC_GPIO1_IO15__GPIO1_IO15		0x11
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001c3
+			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14	0x1e3
+			MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15	0x1e3
+		>;
+	};
+
+	pinctrl_pmic: pmicirqgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18	0x141
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x190
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d0
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d0
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d0
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d0
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d0
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d0
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d0
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d0
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d0
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x190
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x194
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d4
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d4
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d4
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d4
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d4
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d4
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d4
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d4
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d4
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x194
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x196
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d6
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d6
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d6
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d6
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d6
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d6
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d6
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d6
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d6
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B	0xc6
+		>;
+	};
+};
diff --git a/arch/arm/mach-imx/imx8m/Kconfig b/arch/arm/mach-imx/imx8m/Kconfig
index bd2ab77b75..78e4fb6f6c 100644
--- a/arch/arm/mach-imx/imx8m/Kconfig
+++ b/arch/arm/mach-imx/imx8m/Kconfig
@@ -77,6 +77,12 @@ config TARGET_PHYCORE_IMX8MM
 	select IMX8MM
         select SUPPORT_SPL
 	select IMX8M_LPDDR4
+
+config TARGET_PHYCORE_IMX8MP
+	bool "PHYTEC PHYCORE i.MX8MP"
+	select IMX8MP
+        select SUPPORT_SPL
+	select IMX8M_LPDDR4
 endchoice
 
 source "board/freescale/imx8mq_evk/Kconfig"
@@ -88,5 +94,6 @@ source "board/technexion/pico-imx8mq/Kconfig"
 source "board/toradex/verdin-imx8mm/Kconfig"
 source "board/beacon/imx8mm/Kconfig"
 source "board/phytec/phycore_imx8mm/Kconfig"
+source "board/phytec/phycore_imx8mp/Kconfig"
 
 endif