summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
Diffstat
-rw-r--r--AllWinner-net-emac.patch2669
-rw-r--r--bcm283x-vc4-fixes.patch43
-rw-r--r--config-arm641
-rw-r--r--config-armv7-generic1
-rw-r--r--kernel.spec7
5 files changed, 2721 insertions, 0 deletions
diff --git a/AllWinner-net-emac.patch b/AllWinner-net-emac.patch
new file mode 100644
index 000000000..42dadabab
--- /dev/null
+++ b/AllWinner-net-emac.patch
@@ -0,0 +1,2669 @@
+From fb909e29d6c073f4c5777a0db75df72b726e4314 Mon Sep 17 00:00:00 2001
+From: Corentin LABBE <clabbe.montjoie@gmail.com>
+Date: Fri, 7 Oct 2016 10:25:48 +0200
+Subject: [PATCH 1/8] ethernet: add sun8i-emac driver
+
+This patch add support for sun8i-emac ethernet MAC hardware.
+It could be found in Allwinner H3/A83T/A64 SoCs.
+
+It supports 10/100/1000 Mbit/s speed with half/full duplex.
+It can use an internal PHY (MII 10/100) or an external PHY
+via RGMII/RMII.
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+---
+ drivers/net/ethernet/allwinner/Kconfig | 13 +
+ drivers/net/ethernet/allwinner/Makefile | 1 +
+ drivers/net/ethernet/allwinner/sun8i-emac.c | 2266 +++++++++++++++++++++++++++
+ 3 files changed, 2280 insertions(+)
+ create mode 100644 drivers/net/ethernet/allwinner/sun8i-emac.c
+
+diff --git a/drivers/net/ethernet/allwinner/Kconfig b/drivers/net/ethernet/allwinner/Kconfig
+index 47da7e7..060569c 100644
+--- a/drivers/net/ethernet/allwinner/Kconfig
++++ b/drivers/net/ethernet/allwinner/Kconfig
+@@ -33,4 +33,17 @@ config SUN4I_EMAC
+ To compile this driver as a module, choose M here. The module
+ will be called sun4i-emac.
+
++config SUN8I_EMAC
++ tristate "Allwinner sun8i EMAC support"
++ depends on ARCH_SUNXI || COMPILE_TEST
++ depends on OF
++ select MII
++ select PHYLIB
++ ---help---
++ This driver support the sun8i EMAC ethernet driver present on
++ H3/A83T/A64 Allwinner SoCs.
++
++ To compile this driver as a module, choose M here. The module
++ will be called sun8i-emac.
++
+ endif # NET_VENDOR_ALLWINNER
+diff --git a/drivers/net/ethernet/allwinner/Makefile b/drivers/net/ethernet/allwinner/Makefile
+index 03129f7..8bd1693c 100644
+--- a/drivers/net/ethernet/allwinner/Makefile
++++ b/drivers/net/ethernet/allwinner/Makefile
+@@ -3,3 +3,4 @@
+ #
+
+ obj-$(CONFIG_SUN4I_EMAC) += sun4i-emac.o
++obj-$(CONFIG_SUN8I_EMAC) += sun8i-emac.o
+diff --git a/drivers/net/ethernet/allwinner/sun8i-emac.c b/drivers/net/ethernet/allwinner/sun8i-emac.c
+new file mode 100644
+index 0000000..bc74467
+--- /dev/null
++++ b/drivers/net/ethernet/allwinner/sun8i-emac.c
+@@ -0,0 +1,2266 @@
++/*
++ * sun8i-emac driver
++ *
++ * Copyright (C) 2015-2016 Corentin LABBE <clabbe.montjoie@gmail.com>
++ *
++ * This is the driver for Allwinner Ethernet MAC found in H3/A83T/A64 SoC
++ *
++ * TODO:
++ * - MAC filtering
++ * - Jumbo frame
++ * - features rx-all (NETIF_F_RXALL_BIT)
++ * - PM runtime
++ */
++#include <linux/bitops.h>
++#include <linux/clk.h>
++#include <linux/dma-mapping.h>
++#include <linux/etherdevice.h>
++#include <linux/interrupt.h>
++#include <linux/iopoll.h>
++#include <linux/mii.h>
++#include <linux/module.h>
++#include <linux/netdevice.h>
++#include <linux/of_device.h>
++#include <linux/of_mdio.h>
++#include <linux/of_net.h>
++#include <linux/phy.h>
++#include <linux/pinctrl/consumer.h>
++#include <linux/pinctrl/pinctrl.h>
++#include <linux/platform_device.h>
++#include <linux/reset.h>
++#include <linux/scatterlist.h>
++#include <linux/skbuff.h>
++#include <linux/mfd/syscon.h>
++#include <linux/regmap.h>
++
++#define EMAC_BASIC_CTL0 0x00
++#define EMAC_BASIC_CTL1 0x04
++#define EMAC_INT_STA 0x08
++#define EMAC_INT_EN 0x0C
++#define EMAC_TX_CTL0 0x10
++#define EMAC_TX_CTL1 0x14
++#define EMAC_TX_FLOW_CTL 0x1C
++#define EMAC_RX_CTL0 0x24
++#define EMAC_RX_CTL1 0x28
++#define EMAC_RX_FRM_FLT 0x38
++#define EMAC_MDIO_CMD 0x48
++#define EMAC_MDIO_DATA 0x4C
++#define EMAC_TX_DMA_STA 0xB0
++#define EMAC_TX_CUR_DESC 0xB4
++#define EMAC_TX_CUR_BUF 0xB8
++#define EMAC_RX_DMA_STA 0xC0
++
++#define MDIO_CMD_MII_BUSY BIT(0)
++#define MDIO_CMD_MII_WRITE BIT(1)
++#define MDIO_CMD_MII_PHY_REG_ADDR_MASK GENMASK(8, 4)
++#define MDIO_CMD_MII_PHY_REG_ADDR_SHIFT 4
++#define MDIO_CMD_MII_PHY_ADDR_MASK GENMASK(16, 12)
++#define MDIO_CMD_MII_PHY_ADDR_SHIFT 12
++
++#define EMAC_MACADDR_HI 0x50
++#define EMAC_MACADDR_LO 0x54
++
++#define EMAC_RX_DESC_LIST 0x34
++#define EMAC_TX_DESC_LIST 0x20
++
++#define EMAC_RX_DO_CRC BIT(27)
++#define EMAC_RX_STRIP_FCS BIT(28)
++
++#define LE32_BIT(x) (cpu_to_le32(BIT(x)))
++
++#define EMAC_COULD_BE_USED_BY_DMA LE32_BIT(31)
++
++/* Used in RX_CTL1*/
++#define EMAC_RX_DMA_EN BIT(30)
++#define EMAC_RX_DMA_START BIT(31)
++/* Used in TX_CTL1*/
++#define EMAC_TX_DMA_EN BIT(30)
++#define EMAC_TX_DMA_START BIT(31)
++
++/* Used in RX_CTL0 */
++#define EMAC_RX_RECEIVER_EN BIT(31)
++/* Used in TX_CTL0 */
++#define EMAC_TX_TRANSMITTER_EN BIT(31)
++
++/* Basic CTL0 */
++#define EMAC_BCTL0_FD BIT(0)
++#define EMAC_BCTL0_SPEED_10 2
++#define EMAC_BCTL0_SPEED_100 3
++#define EMAC_BCTL0_SPEED_MASK GENMASK(3, 2)
++#define EMAC_BCTL0_SPEED_SHIFT 2
++
++#define EMAC_FLOW_RX 1
++#define EMAC_FLOW_TX 2
++
++#define EMAC_TX_INT BIT(0)
++#define EMAC_TX_DMA_STOP_INT BIT(1)
++#define EMAC_TX_BUF_UA_INT BIT(2)
++#define EMAC_TX_TIMEOUT_INT BIT(3)
++#define EMAC_TX_UNDERFLOW_INT BIT(4)
++#define EMAC_TX_EARLY_INT BIT(5)
++#define EMAC_RX_INT BIT(8)
++#define EMAC_RX_BUF_UA_INT BIT(9)
++#define EMAC_RX_DMA_STOP_INT BIT(10)
++#define EMAC_RX_TIMEOUT_INT BIT(11)
++#define EMAC_RX_OVERFLOW_INT BIT(12)
++#define EMAC_RX_EARLY_INT BIT(13)
++#define EMAC_RGMII_STA_INT BIT(16)
++
++/* Bits used in frame RX status */
++#define EMAC_DSC_RX_FIRST BIT(9)
++#define EMAC_DSC_RX_LAST BIT(8)
++
++/* Bits used in frame TX ctl */
++#define EMAC_MAGIC_TX_BIT LE32_BIT(24)
++#define EMAC_TX_DO_CRC (LE32_BIT(27) | LE32_BIT(28))
++#define EMAC_DSC_TX_FIRST LE32_BIT(29)
++#define EMAC_DSC_TX_LAST LE32_BIT(30)
++#define EMAC_WANT_INT LE32_BIT(31)
++
++/* struct emac_variant - Describe an emac variant of sun8i-emac
++ * @default_syscon_value: Default value of the syscon EMAC register
++ * The default_syscon_value is also used for powering down the PHY
++ * @internal_phy: which PHY type is internal
++ * @support_mii: Does the SoC support MII
++ * @support_rmii: Does the SoC support RMII
++ * @support_rgmii: Does the SoC support RGMII
++ */
++struct emac_variant {
++ u32 default_syscon_value;
++ int internal_phy;
++ bool support_mii;
++ bool support_rmii;
++ bool support_rgmii;
++};
++
++static const struct emac_variant emac_variant_h3 = {
++ .default_syscon_value = 0x58000,
++ .internal_phy = PHY_INTERFACE_MODE_MII,
++ .support_mii = true,
++ .support_rmii = true,
++ .support_rgmii = true
++};
++
++static const struct emac_variant emac_variant_a83t = {
++ .default_syscon_value = 0,
++ .internal_phy = 0,
++ .support_mii = true,
++ .support_rgmii = true
++};
++
++static const struct emac_variant emac_variant_a64 = {
++ .default_syscon_value = 0,
++ .internal_phy = 0,
++ .support_mii = true,
++ .support_rmii = true,
++ .support_rgmii = true
++};
++
++static const char const estats_str[][ETH_GSTRING_LEN] = {
++ /* errors */
++ "rx_payload_error",
++ "rx_CRC_error",
++ "rx_phy_error",
++ "rx_length_error",
++ "rx_col_error",
++ "rx_header_error",
++ "rx_overflow_error",
++ "rx_saf_error",
++ "rx_daf_error",
++ "rx_buf_error",
++ "rx_invalid_error",
++ "tx_timeout",
++ /* misc infos */
++ "tx_stop_queue",
++ "rx_dma_ua",
++ "rx_dma_stop",
++ "tx_dma_ua",
++ "tx_dma_stop",
++ "rx_hw_csum",
++ "tx_hw_csum",
++ /* interrupts */
++ "rx_int",
++ "tx_int",
++ "tx_early_int",
++ "tx_underflow_int",
++ "tx_timeout_int",
++ "rx_early_int",
++ "rx_overflow_int",
++ "rx_timeout_int",
++ "rgmii_state_int",
++ /* debug */
++ "tx_used_desc",
++ "napi_schedule",
++ "napi_underflow",
++};
++
++struct sun8i_emac_stats {
++ u64 rx_payload_error;
++ u64 rx_crc_error;
++ u64 rx_phy_error;
++ u64 rx_length_error;
++ u64 rx_col_error;
++ u64 rx_header_error;
++ u64 rx_overflow_error;
++ u64 rx_saf_fail;
++ u64 rx_daf_fail;
++ u64 rx_buf_error;
++ u64 rx_invalid_error;
++ u64 tx_timeout;
++
++ u64 tx_stop_queue;
++ u64 rx_dma_ua;
++ u64 rx_dma_stop;
++ u64 tx_dma_ua;
++ u64 tx_dma_stop;
++ u64 rx_hw_csum;
++ u64 tx_hw_csum;
++
++ u64 rx_int;
++ u64 tx_int;
++ u64 tx_early_int;
++ u64 tx_underflow_int;
++ u64 tx_timeout_int;
++ u64 rx_early_int;
++ u64 rx_overflow_int;
++ u64 rx_timeout_int;
++ u64 rgmii_state_int;
++
++ u64 tx_used_desc;
++ u64 napi_schedule;
++ u64 napi_underflow;
++};
++
++/* The datasheet said that each descriptor can transfers up to 4096bytes
++ * But latter, a register documentation reduce that value to 2048
++ * Anyway using 2048 cause strange behaviours and even BSP driver use 2047
++ */
++#define DESC_BUF_MAX 2044
++
++/* MAGIC value for knowing if a descriptor is available or not */
++#define DCLEAN cpu_to_le32(BIT(16) | BIT(14) | BIT(12) | BIT(10) | BIT(9))
++
++/* struct dma_desc - Structure of DMA descriptor used by the hardware
++ * @status: Status of the frame written by HW, so RO for the
++ * driver (except for BIT(31) which is R/W)
++ * @ctl: Information on the frame written by the driver (INT, len,...)
++ * @buf_addr: physical address of the frame data
++ * @next: physical address of next dma_desc
++ */
++struct dma_desc {
++ __le32 status;
++ __le32 ctl;
++ __le32 buf_addr;
++ __le32 next;
++};
++
++/* Describe how data from skb are DMA mapped (used in txinfo map member) */
++#define MAP_SINGLE 1
++#define MAP_PAGE 2
++
++/* Structure for storing information about data in TX ring buffer */
++struct txinfo {
++ struct sk_buff *skb;
++ int map;
++};
++
++struct sun8i_emac_priv {
++ void __iomem *base;
++ struct regmap *regmap;
++ int irq;
++ struct device *dev;
++ struct net_device *ndev;
++ struct mii_bus *mdio;
++ struct napi_struct napi;
++ spinlock_t tx_lock;/* control the access of transmit descriptors */
++ int duplex;
++ int speed;
++ int link;
++ int phy_interface;
++ const struct emac_variant *variant;
++ struct device_node *phy_node;
++ struct device_node *mdio_node;
++ struct clk *ahb_clk;
++ struct clk *ephy_clk;
++ bool use_internal_phy;
++
++ struct reset_control *rst_mac;
++ struct reset_control *rst_ephy;
++
++ struct dma_desc *dd_rx;
++ dma_addr_t dd_rx_phy;
++ struct dma_desc *dd_tx;
++ dma_addr_t dd_tx_phy;
++ struct sk_buff **rx_skb;
++ struct txinfo *txl;
++
++ int nbdesc_tx;
++ int nbdesc_rx;
++ int tx_slot;
++ int tx_dirty;
++ int rx_dirty;
++ struct sun8i_emac_stats estats;
++ u32 msg_enable;
++ int flow_ctrl;
++ int pause;
++};
++
++static irqreturn_t sun8i_emac_dma_interrupt(int irq, void *dev_id);
++
++static void rb_inc(int *p, const int max)
++{
++ (*p)++;
++ (*p) %= max;
++}
++
++/* Locking strategy:
++ * RX queue does not need any lock since only sun8i_emac_poll() access it.
++ * (All other RX modifiers (ringparam/ndo_stop) disable NAPI and so
++ * sun8i_emac_poll())
++ * TX queue is handled by sun8i_emac_xmit(), sun8i_emac_complete_xmit() and
++ * sun8i_emac_tx_timeout()
++ * (All other RX modifiers (ringparam/ndo_stop) disable NAPI and stop queue)
++ *
++ * sun8i_emac_xmit() could fire only once (netif_tx_lock)
++ * sun8i_emac_complete_xmit() could fire only once (called from NAPI)
++ * sun8i_emac_tx_timeout() could fire only once (netif_tx_lock) and could not
++ * race with sun8i_emac_xmit (due to netif_tx_lock) and with
++ * sun8i_emac_complete_xmit which disable NAPI.
++ *
++ * So only sun8i_emac_xmit and sun8i_emac_complete_xmit could fire at the same
++ * time.
++ * But they never could modify the same descriptors:
++ * - sun8i_emac_complete_xmit() will modify only descriptors with empty status
++ * - sun8i_emac_xmit() will modify only descriptors set to DCLEAN
++ * Proper memory barriers ensure that descriptor set to DCLEAN could not be
++ * modified latter by sun8i_emac_complete_xmit().
++ */
++
++/* Return the number of contiguous free descriptors
++ * starting from tx_slot
++ */
++static int rb_tx_numfreedesc(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++
++ if (priv->tx_slot < priv->tx_dirty)
++ return priv->tx_dirty - priv->tx_slot;
++
++ return (priv->nbdesc_tx - priv->tx_slot) + priv->tx_dirty;
++}
++
++/* sun8i_emac_rx_skb - Allocate a skb in a DMA descriptor
++ *
++ * @ndev: The net_device for this interface
++ * @i: index of slot to fill
++ *
++ * Refill a DMA descriptor with a fresh skb and map it for DMA.
++*/
++static int sun8i_emac_rx_skb(struct net_device *ndev, int i)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ struct dma_desc *ddesc;
++ struct sk_buff *skb;
++
++ ddesc = priv->dd_rx + i;
++
++ ddesc->ctl = 0;
++
++ skb = netdev_alloc_skb_ip_align(ndev, DESC_BUF_MAX);
++ if (!skb)
++ return -ENOMEM;
++
++ /* should not happen */
++ if (unlikely(priv->rx_skb[i]))
++ dev_warn(priv->dev, "BUG: Leaking a skbuff\n");
++
++ priv->rx_skb[i] = skb;
++
++ ddesc->buf_addr = dma_map_single(priv->dev, skb->data,
++ DESC_BUF_MAX, DMA_FROM_DEVICE);
++ if (dma_mapping_error(priv->dev, ddesc->buf_addr)) {
++ dev_err(priv->dev, "ERROR: Cannot map RX buffer for DMA\n");
++ dev_kfree_skb(skb);
++ return -EFAULT;
++ }
++ /* We cannot direcly use cpu_to_le32() after dma_map_single
++ * since dma_mapping_error use it
++ */
++ ddesc->buf_addr = cpu_to_le32(ddesc->buf_addr);
++ ddesc->ctl |= cpu_to_le32(DESC_BUF_MAX);
++ /* EMAC_COULD_BE_USED_BY_DMA must be the last value written */
++ wmb();
++ ddesc->status = EMAC_COULD_BE_USED_BY_DMA;
++
++ return 0;
++}
++
++static void sun8i_emac_stop_tx(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ u32 v;
++
++ netif_stop_queue(ndev);
++
++ v = readl(priv->base + EMAC_TX_CTL0);
++ /* Disable transmitter after current reception */
++ v &= ~EMAC_TX_TRANSMITTER_EN;
++ writel(v, priv->base + EMAC_TX_CTL0);
++
++ v = readl(priv->base + EMAC_TX_CTL1);
++ /* Stop TX DMA */
++ v &= ~EMAC_TX_DMA_EN;
++ writel(v, priv->base + EMAC_TX_CTL1);
++
++ /* We must be sure that all is stopped before leaving this function */
++ wmb();
++}
++
++static void sun8i_emac_stop_rx(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ u32 v;
++
++ v = readl(priv->base + EMAC_RX_CTL0);
++ /* Disable receiver after current reception */
++ v &= ~EMAC_RX_RECEIVER_EN;
++ writel(v, priv->base + EMAC_RX_CTL0);
++
++ v = readl(priv->base + EMAC_RX_CTL1);
++ /* Stop RX DMA */
++ v &= ~EMAC_RX_DMA_EN;
++ writel(v, priv->base + EMAC_RX_CTL1);
++
++ /* We must be sure that all is stopped before leaving this function */
++ wmb();
++}
++
++static void sun8i_emac_start_rx(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ u32 v;
++
++ v = readl(priv->base + EMAC_RX_CTL0);
++ /* Enable receiver */
++ v |= EMAC_RX_RECEIVER_EN;
++ writel(v, priv->base + EMAC_RX_CTL0);
++
++ v = readl(priv->base + EMAC_RX_CTL1);
++ v |= EMAC_RX_DMA_START;
++ v |= EMAC_RX_DMA_EN;
++ writel(v, priv->base + EMAC_RX_CTL1);
++}
++
++static void sun8i_emac_start_tx(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ u32 v;
++
++ v = readl(priv->base + EMAC_TX_CTL0);
++ v |= EMAC_TX_TRANSMITTER_EN;
++ writel(v, priv->base + EMAC_TX_CTL0);
++
++ v = readl(priv->base + EMAC_TX_CTL1);
++ v |= EMAC_TX_DMA_START;
++ v |= EMAC_TX_DMA_EN;
++ writel(v, priv->base + EMAC_TX_CTL1);
++}
++
++/* sun8i_emac_set_macaddr - Set MAC address for slot index
++ *
++ * @addr: the MAC address to set
++ * @index: The index of slot where to set address.
++ *
++ * The slot 0 is the main MAC address
++ */
++static void sun8i_emac_set_macaddr(struct sun8i_emac_priv *priv,
++ const u8 *addr, int index)
++{
++ u32 v;
++
++ dev_info(priv->dev, "device MAC address slot %d %pM", index, addr);
++
++ v = (addr[5] << 8) | addr[4];
++ writel(v, priv->base + EMAC_MACADDR_HI + index * 8);
++
++ v = (addr[3] << 24) | (addr[2] << 16) | (addr[1] << 8) | addr[0];
++ writel(v, priv->base + EMAC_MACADDR_LO + index * 8);
++}
++
++static void sun8i_emac_set_link_mode(struct sun8i_emac_priv *priv)
++{
++ u32 v;
++
++ v = readl(priv->base + EMAC_BASIC_CTL0);
++
++ if (priv->duplex)
++ v |= EMAC_BCTL0_FD;
++ else
++ v &= ~EMAC_BCTL0_FD;
++
++ v &= ~EMAC_BCTL0_SPEED_MASK;
++
++ switch (priv->speed) {
++ case 1000:
++ break;
++ case 100:
++ v |= EMAC_BCTL0_SPEED_100 << EMAC_BCTL0_SPEED_SHIFT;
++ break;
++ case 10:
++ v |= EMAC_BCTL0_SPEED_10 << EMAC_BCTL0_SPEED_SHIFT;
++ break;
++ default:
++ dev_err(priv->dev, "Unsupported speed %d\n", priv->speed);
++ return;
++ }
++
++ writel(v, priv->base + EMAC_BASIC_CTL0);
++}
++
++static void sun8i_emac_flow_ctrl(struct sun8i_emac_priv *priv, int duplex,
++ int fc)
++{
++ u32 flow = 0;
++
++ flow = readl(priv->base + EMAC_RX_CTL0);
++ if (fc & EMAC_FLOW_RX)
++ flow |= BIT(16);
++ else
++ flow &= ~BIT(16);
++ writel(flow, priv->base + EMAC_RX_CTL0);
++
++ flow = readl(priv->base + EMAC_TX_FLOW_CTL);
++ if (fc & EMAC_FLOW_TX)
++ flow |= BIT(0);
++ else
++ flow &= ~BIT(0);
++ writel(flow, priv->base + EMAC_TX_FLOW_CTL);
++}
++
++/* Grab a frame into a skb from descriptor number i */
++static int sun8i_emac_rx_from_ddesc(struct net_device *ndev, int i)
++{
++ struct sk_buff *skb;
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ struct dma_desc *ddesc = priv->dd_rx + i;
++ int frame_len;
++ int rxcsum_done = 0;
++ u32 dstatus = le32_to_cpu(ddesc->status);
++
++ if (ndev->features & NETIF_F_RXCSUM)
++ rxcsum_done = 1;
++
++ /* bit0/bit7 work only on IPv4/IPv6 TCP traffic,
++ * (not on ARP for example) so we do not raise rx_errors/discard frame
++ */
++ /* the checksum or length of received frame's payload is wrong*/
++ if (dstatus & BIT(0)) {
++ priv->estats.rx_payload_error++;
++ rxcsum_done = 0;
++ }
++
++ /* RX_CRC_ERR */
++ if (dstatus & BIT(1)) {
++ priv->ndev->stats.rx_errors++;
++ priv->ndev->stats.rx_crc_errors++;
++ priv->estats.rx_crc_error++;
++ goto discard_frame;
++ }
++
++ /* RX_PHY_ERR */
++ if ((dstatus & BIT(3))) {
++ priv->ndev->stats.rx_errors++;
++ priv->estats.rx_phy_error++;
++ goto discard_frame;
++ }
++
++ /* RX_LENGTH_ERR */
++ if ((dstatus & BIT(4))) {
++ priv->ndev->stats.rx_errors++;
++ priv->ndev->stats.rx_length_errors++;
++ priv->estats.rx_length_error++;
++ goto discard_frame;
++ }
++
++ /* RX_COL_ERR */
++ if ((dstatus & BIT(6))) {
++ priv->ndev->stats.rx_errors++;
++ priv->estats.rx_col_error++;
++ goto discard_frame;
++ }
++
++ /* RX_HEADER_ERR */
++ if ((dstatus & BIT(7))) {
++ priv->estats.rx_header_error++;
++ rxcsum_done = 0;
++ }
++
++ /* RX_OVERFLOW_ERR */
++ if ((dstatus & BIT(11))) {
++ priv->ndev->stats.rx_over_errors++;
++ priv->estats.rx_overflow_error++;
++ goto discard_frame;
++ }
++
++ /* RX_NO_ENOUGTH_BUF_ERR */
++ if ((dstatus & BIT(14))) {
++ priv->ndev->stats.rx_errors++;
++ priv->estats.rx_buf_error++;
++ goto discard_frame;
++ }
++
++ /* BIT(9) is for the first frame, not having it is bad since we do not
++ * handle Jumbo frame
++ */
++ if ((dstatus & EMAC_DSC_RX_FIRST) == 0) {
++ priv->ndev->stats.rx_errors++;
++ priv->estats.rx_invalid_error++;
++ goto discard_frame;
++ }
++
++ /* this frame is not the last */
++ if ((dstatus & EMAC_DSC_RX_LAST) == 0) {
++ priv->ndev->stats.rx_errors++;
++ priv->estats.rx_invalid_error++;
++ goto discard_frame;
++ }
++
++ frame_len = (dstatus >> 16) & 0x3FFF;
++ if (!(ndev->features & NETIF_F_RXFCS))
++ frame_len -= ETH_FCS_LEN;
++
++ skb = priv->rx_skb[i];
++
++ netif_dbg(priv, rx_status, priv->ndev,
++ "%s from %02d %pad len=%d status=%x st=%x\n",
++ __func__, i, &ddesc, frame_len, dstatus,
++ cpu_to_le32(ddesc->ctl));
++
++ skb_put(skb, frame_len);
++
++ dma_unmap_single(priv->dev, le32_to_cpu(ddesc->buf_addr), DESC_BUF_MAX,
++ DMA_FROM_DEVICE);
++ skb->protocol = eth_type_trans(skb, priv->ndev);
++ if (rxcsum_done) {
++ skb->ip_summed = CHECKSUM_UNNECESSARY;
++ priv->estats.rx_hw_csum++;
++ } else {
++ skb->ip_summed = CHECKSUM_PARTIAL;
++ }
++
++ priv->ndev->stats.rx_packets++;
++ priv->ndev->stats.rx_bytes += frame_len;
++ priv->rx_skb[i] = NULL;
++
++ sun8i_emac_rx_skb(ndev, i);
++ napi_gro_receive(&priv->napi, skb);
++
++ return 0;
++ /* If the frame need to be dropped, we simply reuse the buffer */
++discard_frame:
++ ddesc->ctl = cpu_to_le32(DESC_BUF_MAX);
++ /* EMAC_COULD_BE_USED_BY_DMA must be the last value written */
++ wmb();
++ ddesc->status = EMAC_COULD_BE_USED_BY_DMA;
++ return 0;
++}
++
++/* Iterate over dma_desc for finding completed xmit.
++ *
++ * The problem is: how to know that a descriptor is sent and not just in
++ * preparation.
++ * Need to have status=0 and st set but this is the state of first frame just
++ * before setting the own-by-DMA bit.
++ * The solution is to used the artificial value DCLEAN.
++ */
++static int sun8i_emac_complete_xmit(struct net_device *ndev, int budget)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ struct dma_desc *ddesc;
++ int frame_len;
++ int work = 0;
++ unsigned int bytes_compl = 0, pkts_compl = 0;
++ u32 dstatus;
++
++ do {
++ ddesc = priv->dd_tx + priv->tx_dirty;
++
++ if (ddesc->status & EMAC_COULD_BE_USED_BY_DMA)
++ goto xmit_end;
++
++ if (ddesc->status == DCLEAN)
++ goto xmit_end;
++
++ dstatus = cpu_to_le32(ddesc->status);
++
++ if (ddesc->status == 0 && !ddesc->ctl) {
++ dev_err(priv->dev, "BUG: reached the void %d %d\n",
++ priv->tx_dirty, priv->tx_slot);
++ goto xmit_end;
++ }
++
++ /* TX_UNDERFLOW_ERR */
++ if (dstatus & BIT(1))
++ priv->ndev->stats.tx_errors++;
++ /* TX_DEFER_ERR */
++ if (dstatus & BIT(2))
++ priv->ndev->stats.tx_errors++;
++ /* BIT 6:3 numbers of collisions */
++ if (dstatus & 0x78)
++ priv->ndev->stats.collisions +=
++ (dstatus & 0x78) >> 3;
++ /* TX_COL_ERR_1 */
++ if (dstatus & BIT(8))
++ priv->ndev->stats.tx_errors++;
++ /* TX_COL_ERR_0 */
++ if (dstatus & BIT(9))
++ priv->ndev->stats.tx_errors++;
++ /* TX_CRS_ERR */
++ if (dstatus & BIT(10))
++ priv->ndev->stats.tx_carrier_errors++;
++ /* TX_PAYLOAD_ERR */
++ if (dstatus & BIT(12))
++ priv->ndev->stats.tx_errors++;
++ /* TX_LENGTH_ERR */
++ if (dstatus & BIT(14))
++ priv->ndev->stats.tx_errors++;
++ /* TX_HEADER_ERR */
++ if (dstatus & BIT(16))
++ priv->ndev->stats.tx_errors++;
++
++ frame_len = le32_to_cpu(ddesc->ctl) & 0x3FFF;
++ bytes_compl += frame_len;
++
++ if (priv->txl[priv->tx_dirty].map == MAP_SINGLE)
++ dma_unmap_single(priv->dev,
++ le32_to_cpu(ddesc->buf_addr),
++ frame_len, DMA_TO_DEVICE);
++ else
++ dma_unmap_page(priv->dev,
++ le32_to_cpu(ddesc->buf_addr),
++ frame_len, DMA_TO_DEVICE);
++ /* we can free skb only on last frame */
++ if (priv->txl[priv->tx_dirty].skb &&
++ (ddesc->ctl & EMAC_DSC_TX_LAST)) {
++ dev_kfree_skb_irq(priv->txl[priv->tx_dirty].skb);
++ pkts_compl++;
++ }
++
++ priv->txl[priv->tx_dirty].skb = NULL;
++ priv->txl[priv->tx_dirty].map = 0;
++ ddesc->ctl = 0;
++ /* setting status to DCLEAN is the last value to be set */
++ wmb();
++ ddesc->status = DCLEAN;
++ work++;
++
++ rb_inc(&priv->tx_dirty, priv->nbdesc_tx);
++ ddesc = priv->dd_tx + priv->tx_dirty;
++ } while (ddesc->ctl &&
++ !(ddesc->status & EMAC_COULD_BE_USED_BY_DMA) &&
++ work < budget);
++
++xmit_end:
++ netdev_completed_queue(ndev, pkts_compl, bytes_compl);
++
++ /* if we don't have handled all packets */
++ if (work < budget)
++ work = 0;
++
++ if (netif_queue_stopped(ndev) &&
++ rb_tx_numfreedesc(ndev) > MAX_SKB_FRAGS + 1)
++ netif_wake_queue(ndev);
++ return work;
++}
++
++static int sun8i_emac_poll(struct napi_struct *napi, int budget)
++{
++ struct sun8i_emac_priv *priv =
++ container_of(napi, struct sun8i_emac_priv, napi);
++ struct net_device *ndev = priv->ndev;
++ int worked;
++ struct dma_desc *ddesc;
++
++ priv->estats.napi_schedule++;
++ worked = sun8i_emac_complete_xmit(ndev, budget);
++
++ ddesc = priv->dd_rx + priv->rx_dirty;
++ while (!(ddesc->status & EMAC_COULD_BE_USED_BY_DMA) &&
++ worked < budget) {
++ sun8i_emac_rx_from_ddesc(ndev, priv->rx_dirty);
++ worked++;
++ rb_inc(&priv->rx_dirty, priv->nbdesc_rx);
++ ddesc = priv->dd_rx + priv->rx_dirty;
++ };
++ if (worked < budget) {
++ priv->estats.napi_underflow++;
++ napi_complete(&priv->napi);
++ writel(EMAC_RX_INT | EMAC_TX_INT, priv->base + EMAC_INT_EN);
++ }
++ return worked;
++}
++
++static int sun8i_mdio_read(struct mii_bus *bus, int phy_addr, int phy_reg)
++{
++ struct net_device *ndev = bus->priv;
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ int err;
++ u32 reg;
++
++ err = readl_poll_timeout(priv->base + EMAC_MDIO_CMD, reg,
++ !(reg & MDIO_CMD_MII_BUSY), 100, 10000);
++ if (err) {
++ dev_err(priv->dev, "%s timeout %x\n", __func__, reg);
++ return err;
++ }
++
++ reg &= ~MDIO_CMD_MII_WRITE;
++ reg &= ~MDIO_CMD_MII_PHY_REG_ADDR_MASK;
++ reg |= (phy_reg << MDIO_CMD_MII_PHY_REG_ADDR_SHIFT) &
++ MDIO_CMD_MII_PHY_REG_ADDR_MASK;
++
++ reg &= ~MDIO_CMD_MII_PHY_ADDR_MASK;
++
++ reg |= (phy_addr << MDIO_CMD_MII_PHY_ADDR_SHIFT) &
++ MDIO_CMD_MII_PHY_ADDR_MASK;
++
++ reg |= MDIO_CMD_MII_BUSY;
++
++ writel(reg, priv->base + EMAC_MDIO_CMD);
++
++ err = readl_poll_timeout(priv->base + EMAC_MDIO_CMD, reg,
++ !(reg & MDIO_CMD_MII_BUSY), 100, 10000);
++
++ if (err) {
++ dev_err(priv->dev, "%s timeout %x\n", __func__, reg);
++ return err;
++ }
++
++ return readl(priv->base + EMAC_MDIO_DATA);
++}
++
++static int sun8i_mdio_write(struct mii_bus *bus, int phy_addr, int phy_reg,
++ u16 data)
++{
++ struct net_device *ndev = bus->priv;
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ u32 reg;
++ int err;
++
++ err = readl_poll_timeout(priv->base + EMAC_MDIO_CMD, reg,
++ !(reg & MDIO_CMD_MII_BUSY), 100, 10000);
++ if (err) {
++ dev_err(priv->dev, "%s timeout %x\n", __func__, reg);
++ return err;
++ }
++
++ reg &= ~MDIO_CMD_MII_PHY_REG_ADDR_MASK;
++ reg |= (phy_reg << MDIO_CMD_MII_PHY_REG_ADDR_SHIFT) &
++ MDIO_CMD_MII_PHY_REG_ADDR_MASK;
++
++ reg &= ~MDIO_CMD_MII_PHY_ADDR_MASK;
++ reg |= (phy_addr << MDIO_CMD_MII_PHY_ADDR_SHIFT) &
++ MDIO_CMD_MII_PHY_ADDR_MASK;
++
++ reg |= MDIO_CMD_MII_WRITE;
++ reg |= MDIO_CMD_MII_BUSY;
++
++ writel(reg, priv->base + EMAC_MDIO_CMD);
++ writel(data, priv->base + EMAC_MDIO_DATA);
++
++ err = readl_poll_timeout(priv->base + EMAC_MDIO_CMD, reg,
++ !(reg & MDIO_CMD_MII_BUSY), 100, 10000);
++ if (err) {
++ dev_err(priv->dev, "%s timeout %x\n", __func__, reg);
++ return err;
++ }
++
++ return 0;
++}
++
++static int sun8i_emac_mdio_register(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ struct mii_bus *bus;
++ int ret;
++
++ bus = mdiobus_alloc();
++ if (!bus) {
++ netdev_err(ndev, "Failed to allocate a new mdio bus\n");
++ return -ENOMEM;
++ }
++
++ bus->name = dev_name(priv->dev);
++ bus->read = &sun8i_mdio_read;
++ bus->write = &sun8i_mdio_write;
++ snprintf(bus->id, MII_BUS_ID_SIZE, "%s-%x", bus->name, priv->dev->id);
++
++ bus->parent = priv->dev;
++ bus->priv = ndev;
++
++ ret = of_mdiobus_register(bus, priv->mdio_node);
++ if (ret) {
++ netdev_err(ndev, "Could not register a MDIO bus: %d\n", ret);
++ mdiobus_free(bus);
++ return ret;
++ }
++
++ priv->mdio = bus;
++
++ return 0;
++}
++
++static void sun8i_emac_mdio_unregister(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++
++ mdiobus_unregister(priv->mdio);
++ mdiobus_free(priv->mdio);
++}
++
++/* Run within phydev->lock */
++static void sun8i_emac_adjust_link(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ struct phy_device *phydev = ndev->phydev;
++ int new_state = 0;
++
++ netif_dbg(priv, link, priv->ndev,
++ "%s link=%x duplex=%x speed=%x\n", __func__,
++ phydev->link, phydev->duplex, phydev->speed);
++ if (!phydev)
++ return;
++
++ if (phydev->link) {
++ if (phydev->duplex != priv->duplex) {
++ new_state = 1;
++ priv->duplex = phydev->duplex;
++ }
++ if (phydev->pause)
++ sun8i_emac_flow_ctrl(priv, phydev->duplex,
++ priv->flow_ctrl);
++
++ if (phydev->speed != priv->speed) {
++ new_state = 1;
++ priv->speed = phydev->speed;
++ }
++
++ if (priv->link == 0) {
++ new_state = 1;
++ priv->link = phydev->link;
++ }
++
++ netif_dbg(priv, link, priv->ndev,
++ "%s new=%d link=%d pause=%d\n",
++ __func__, new_state, priv->link, phydev->pause);
++ if (new_state)
++ sun8i_emac_set_link_mode(priv);
++ } else if (priv->link != phydev->link) {
++ new_state = 1;
++ priv->link = 0;
++ priv->speed = 0;
++ priv->duplex = -1;
++ }
++
++ if (new_state)
++ phy_print_status(phydev);
++}
++
++/* H3 specific bits for EPHY */
++#define H3_EPHY_ADDR_SHIFT 20
++#define H3_EPHY_LED_POL BIT(17) /* 1: active low, 0: active high */
++#define H3_EPHY_SHUTDOWN BIT(16) /* 1: shutdown, 0: power up */
++#define H3_EPHY_SELECT BIT(15) /* 1: internal PHY, 0: external PHY */
++
++/* H3/A64 specific bits */
++#define SYSCON_RMII_EN BIT(13) /* 1: enable RMII (overrides EPIT) */
++
++/* Generic system control EMAC_CLK bits */
++#define SYSCON_ETXDC_MASK GENMASK(2, 0)
++#define SYSCON_ETXDC_SHIFT 10
++#define SYSCON_ERXDC_MASK GENMASK(4, 0)
++#define SYSCON_ERXDC_SHIFT 5
++/* EMAC PHY Interface Type */
++#define SYSCON_EPIT BIT(2) /* 1: RGMII, 0: MII */
++#define SYSCON_ETCS_MASK GENMASK(1, 0)
++#define SYSCON_ETCS_MII 0x0
++#define SYSCON_ETCS_EXT_GMII 0x1
++#define SYSCON_ETCS_INT_GMII 0x2
++#define SYSCON_EMAC_REG 0x30
++
++static int sun8i_emac_set_syscon(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ struct device_node *node = priv->dev->of_node;
++ int ret;
++ u32 reg, val;
++
++ reg = priv->variant->default_syscon_value;
++
++ if (priv->variant->internal_phy) {
++ if (!priv->use_internal_phy) {
++ /* switch to external PHY interface */
++ reg &= ~H3_EPHY_SELECT;
++ } else {
++ reg |= H3_EPHY_SELECT;
++ reg &= ~H3_EPHY_SHUTDOWN;
++
++ if (of_property_read_bool(priv->phy_node,
++ "allwinner,leds-active-low"))
++ reg |= H3_EPHY_LED_POL;
++
++ ret = of_mdio_parse_addr(priv->dev, priv->phy_node);
++ if (ret < 0) {
++ netdev_err(ndev, "Could not parse MDIO addr\n");
++ return ret;
++ }
++ /* of_mdio_parse_addr returns a valid (0 ~ 31) PHY
++ * address. No need to mask it again.
++ */
++ reg |= ret << H3_EPHY_ADDR_SHIFT;
++ }
++ }
++
++ if (!of_property_read_u32(node, "allwinner,tx-delay", &val)) {
++ if (val <= SYSCON_ETXDC_MASK) {
++ reg &= ~(SYSCON_ETXDC_MASK << SYSCON_ETXDC_SHIFT);
++ reg |= (val << SYSCON_ETXDC_SHIFT);
++ } else {
++ netdev_warn(ndev, "Invalid TX clock delay: %d\n", val);
++ }
++ }
++
++ if (!of_property_read_u32(node, "allwinner,rx-delay", &val)) {
++ if (val <= SYSCON_ERXDC_MASK) {
++ reg &= ~(SYSCON_ERXDC_MASK << SYSCON_ERXDC_SHIFT);
++ reg |= (val << SYSCON_ERXDC_SHIFT);
++ } else {
++ netdev_warn(ndev, "Invalid RX clock delay: %d\n", val);
++ }
++ }
++
++ /* Clear interface mode bits */
++ reg &= ~(SYSCON_ETCS_MASK | SYSCON_EPIT);
++ if (priv->variant->support_rmii)
++ reg &= ~SYSCON_RMII_EN;
++
++ switch (priv->phy_interface) {
++ case PHY_INTERFACE_MODE_MII:
++ /* default */
++ break;
++ case PHY_INTERFACE_MODE_RGMII:
++ reg |= SYSCON_EPIT | SYSCON_ETCS_INT_GMII;
++ break;
++ case PHY_INTERFACE_MODE_RMII:
++ reg |= SYSCON_RMII_EN | SYSCON_ETCS_EXT_GMII;
++ break;
++ default:
++ netdev_err(ndev, "Unsupported interface mode: %s",
++ phy_modes(priv->phy_interface));
++ return -EINVAL;
++ }
++
++ regmap_write(priv->regmap, SYSCON_EMAC_REG, reg);
++
++ return 0;
++}
++
++static void sun8i_emac_unset_syscon(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ u32 reg = priv->variant->default_syscon_value;
++
++ regmap_write(priv->regmap, SYSCON_EMAC_REG, reg);
++}
++
++/* Set Management Data Clock, must be call after device reset */
++static void sun8i_emac_set_mdc(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ unsigned long rate;
++ u32 reg;
++
++ rate = clk_get_rate(priv->ahb_clk);
++ if (rate > 160000000)
++ reg = 0x3 << 20; /* AHB / 128 */
++ else if (rate > 80000000)
++ reg = 0x2 << 20; /* AHB / 64 */
++ else if (rate > 40000000)
++ reg = 0x1 << 20; /* AHB / 32 */
++ else
++ reg = 0x0 << 20; /* AHB / 16 */
++ netif_dbg(priv, link, ndev, "MDC auto : %x\n", reg);
++ writel(reg, priv->base + EMAC_MDIO_CMD);
++}
++
++/* "power" the device, by enabling clk/reset/regulators */
++static int sun8i_emac_power(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ int ret;
++
++ ret = clk_prepare_enable(priv->ahb_clk);
++ if (ret) {
++ netdev_err(ndev, "Could not enable AHB clock\n");
++ return ret;
++ }
++
++ if (priv->rst_mac) {
++ ret = reset_control_deassert(priv->rst_mac);
++ if (ret) {
++ netdev_err(ndev, "Could not deassert reset\n");
++ goto err_reset;
++ }
++ }
++
++ if (priv->ephy_clk) {
++ ret = clk_prepare_enable(priv->ephy_clk);
++ if (ret) {
++ netdev_err(ndev, "Could not enable EPHY clock\n");
++ goto err_ephy_clk;
++ }
++ }
++
++ if (priv->rst_ephy) {
++ ret = reset_control_deassert(priv->rst_ephy);
++ if (ret) {
++ netdev_err(ndev, "Could not deassert EPHY reset\n");
++ goto err_ephy_reset;
++ }
++ }
++
++ return 0;
++
++err_ephy_reset:
++ if (priv->ephy_clk)
++ clk_disable_unprepare(priv->ephy_clk);
++err_ephy_clk:
++ if (priv->rst_mac)
++ reset_control_assert(priv->rst_mac);
++err_reset:
++ clk_disable_unprepare(priv->ahb_clk);
++ return ret;
++}
++
++/* "Unpower" the device, disabling clocks and regulators, asserting reset */
++static void sun8i_emac_unpower(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++
++ if (priv->rst_ephy)
++ reset_control_assert(priv->rst_ephy);
++
++ if (priv->ephy_clk)
++ clk_disable_unprepare(priv->ephy_clk);
++
++ if (priv->rst_mac)
++ reset_control_assert(priv->rst_mac);
++
++ clk_disable_unprepare(priv->ahb_clk);
++}
++
++static int sun8i_emac_init(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ struct device_node *node = priv->dev->of_node;
++ const u8 *addr;
++
++ /* Try to get MAC address from DT, or assign a random one */
++ addr = of_get_mac_address(node);
++ if (addr)
++ ether_addr_copy(ndev->dev_addr, addr);
++ else
++ eth_hw_addr_random(ndev);
++
++ return 0;
++}
++
++static int sun8i_emac_mdio_probe(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ struct phy_device *phydev = NULL;
++
++ phydev = of_phy_connect(ndev, priv->phy_node, &sun8i_emac_adjust_link,
++ 0, priv->phy_interface);
++
++ if (!phydev) {
++ netdev_err(ndev, "Could not attach to PHY\n");
++ return -ENODEV;
++ }
++
++ phy_attached_info(phydev);
++
++ /* mask with MAC supported features */
++ phydev->supported &= PHY_GBIT_FEATURES;
++ phydev->advertising = phydev->supported;
++
++ priv->link = 0;
++ priv->speed = 0;
++ priv->duplex = -1;
++
++ return 0;
++}
++
++/* Allocate both RX and TX ring buffer and init them
++ * This function also write the startbase of thoses ring in the device.
++ * All structures that help managing thoses rings are also handled
++ * by this functions (rx_skb/txl)
++ */
++static int sun8i_emac_alloc_rings(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ struct dma_desc *ddesc;
++ int err, i;
++
++ priv->rx_skb = kcalloc(priv->nbdesc_rx, sizeof(struct sk_buff *),
++ GFP_KERNEL);
++ if (!priv->rx_skb) {
++ err = -ENOMEM;
++ goto rx_skb_error;
++ }
++ priv->txl = kcalloc(priv->nbdesc_tx, sizeof(struct txinfo), GFP_KERNEL);
++ if (!priv->txl) {
++ err = -ENOMEM;
++ goto tx_error;
++ }
++
++ /* allocate/init RX ring */
++ priv->dd_rx = dma_zalloc_coherent(priv->dev,
++ priv->nbdesc_rx * sizeof(struct dma_desc),
++ &priv->dd_rx_phy, GFP_KERNEL);
++ if (!priv->dd_rx) {
++ dev_err(priv->dev, "ERROR: cannot allocate DMA RX buffer");
++ err = -ENOMEM;
++ goto dma_rx_error;
++ }
++ ddesc = priv->dd_rx;
++ for (i = 0; i < priv->nbdesc_rx; i++) {
++ sun8i_emac_rx_skb(ndev, i);
++ ddesc->next = cpu_to_le32(priv->dd_rx_phy + (i + 1)
++ * sizeof(struct dma_desc));
++ ddesc++;
++ }
++ /* last descriptor point back to first one */
++ ddesc--;
++ ddesc->next = cpu_to_le32(priv->dd_rx_phy);
++
++ /* allocate/init TX ring */
++ priv->dd_tx = dma_zalloc_coherent(priv->dev,
++ priv->nbdesc_tx * sizeof(struct dma_desc),
++ &priv->dd_tx_phy, GFP_KERNEL);
++ if (!priv->dd_tx) {
++ dev_err(priv->dev, "ERROR: cannot allocate DMA TX buffer");
++ err = -ENOMEM;
++ goto dma_tx_error;
++ }
++ ddesc = priv->dd_tx;
++ for (i = 0; i < priv->nbdesc_tx; i++) {
++ ddesc->status = DCLEAN;
++ ddesc->ctl = 0;
++ ddesc->next = cpu_to_le32(priv->dd_tx_phy + (i + 1)
++ * sizeof(struct dma_desc));
++ ddesc++;
++ }
++ /* last descriptor point back to first one */
++ ddesc--;
++ ddesc->next = cpu_to_le32(priv->dd_tx_phy);
++ i--;
++
++ priv->tx_slot = 0;
++ priv->tx_dirty = 0;
++ priv->rx_dirty = 0;
++
++ /* write start of RX ring descriptor */
++ writel(priv->dd_rx_phy, priv->base + EMAC_RX_DESC_LIST);
++ /* write start of TX ring descriptor */
++ writel(priv->dd_tx_phy, priv->base + EMAC_TX_DESC_LIST);
++
++ return 0;
++dma_tx_error:
++ dma_free_coherent(priv->dev, priv->nbdesc_rx * sizeof(struct dma_desc),
++ priv->dd_rx, priv->dd_rx_phy);
++dma_rx_error:
++ kfree(priv->txl);
++tx_error:
++ kfree(priv->rx_skb);
++rx_skb_error:
++ return err;
++}
++
++static int sun8i_emac_open(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ int err;
++ u32 v;
++
++ err = sun8i_emac_power(ndev);
++ if (err)
++ return err;
++
++ err = request_irq(priv->irq, sun8i_emac_dma_interrupt, 0,
++ dev_name(priv->dev), ndev);
++ if (err) {
++ dev_err(priv->dev, "Cannot request IRQ: %d\n", err);
++ goto err_power;
++ }
++
++ /* Set interface mode (and configure internal PHY on H3) */
++ err = sun8i_emac_set_syscon(ndev);
++ if (err)
++ goto err_irq;
++
++ /* Do SOFT RST */
++ v = readl(priv->base + EMAC_BASIC_CTL1);
++ writel(v | 0x01, priv->base + EMAC_BASIC_CTL1);
++
++ err = readl_poll_timeout(priv->base + EMAC_BASIC_CTL1, v,
++ !(v & 0x01), 100, 10000);
++ if (err) {
++ dev_err(priv->dev, "EMAC reset timeout\n");
++ err = -EFAULT;
++ goto err_syscon;
++ }
++
++ sun8i_emac_set_mdc(ndev);
++
++ err = sun8i_emac_mdio_register(ndev);
++ if (err)
++ goto err_syscon;
++
++ err = sun8i_emac_mdio_probe(ndev);
++ if (err)
++ goto err_syscon;
++
++ /* DMA */
++ v = (8 << 24);/* burst len */
++ writel(v, priv->base + EMAC_BASIC_CTL1);
++
++ writel(EMAC_RX_INT | EMAC_TX_INT, priv->base + EMAC_INT_EN);
++
++ v = readl(priv->base + EMAC_RX_CTL0);
++ /* CHECK_CRC */
++ if (ndev->features & NETIF_F_RXCSUM)
++ v |= EMAC_RX_DO_CRC;
++ else
++ v &= ~EMAC_RX_DO_CRC;
++ /* STRIP_FCS */
++ if (ndev->features & NETIF_F_RXFCS)
++ v &= ~EMAC_RX_STRIP_FCS;
++ else
++ v |= EMAC_RX_STRIP_FCS;
++ writel(v, priv->base + EMAC_RX_CTL0);
++
++ v = readl(priv->base + EMAC_TX_CTL1);
++ /* TX_MD Transmission starts after a full frame located in TX DMA FIFO*/
++ v |= BIT(1);
++ /* Undocumented bit (called TX_NEXT_FRM in BSP), the original comment is
++ * "Operating on second frame increase the performance
++ * especially when transmit store-and-forward is used."
++ */
++ v |= BIT(2);
++ writel(v, priv->base + EMAC_TX_CTL1);
++
++ v = readl(priv->base + EMAC_RX_CTL1);
++ /* RX_MD RX DMA reads data from RX DMA FIFO to host memory after a
++ * complete frame has been written to RX DMA FIFO
++ */
++ v |= BIT(1);
++ writel(v, priv->base + EMAC_RX_CTL1);
++
++ sun8i_emac_set_macaddr(priv, ndev->dev_addr, 0);
++
++ err = sun8i_emac_alloc_rings(ndev);
++ if (err) {
++ netdev_err(ndev, "Fail to allocate rings\n");
++ goto err_mdio;
++ }
++
++ phy_start(ndev->phydev);
++
++ sun8i_emac_start_rx(ndev);
++ sun8i_emac_start_tx(ndev);
++
++ netif_napi_add(ndev, &priv->napi, sun8i_emac_poll, 64);
++ napi_enable(&priv->napi);
++ netif_start_queue(ndev);
++
++ return 0;
++err_mdio:
++ phy_disconnect(ndev->phydev);
++err_syscon:
++ sun8i_emac_unset_syscon(ndev);
++err_irq:
++ free_irq(priv->irq, ndev);
++err_power:
++ sun8i_emac_unpower(ndev);
++ return err;
++}
++
++/* Clean the TX ring of any accepted skb for xmit */
++static void sun8i_emac_tx_clean(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ int i;
++ struct dma_desc *ddesc;
++ int frame_len;
++
++ for (i = 0; i < priv->nbdesc_tx; i++) {
++ if (priv->txl[i].skb) {
++ ddesc = priv->dd_tx + i;
++ frame_len = le32_to_cpu(ddesc->ctl) & 0x3FFF;
++ switch (priv->txl[i].map) {
++ case MAP_SINGLE:
++ dma_unmap_single(priv->dev,
++ le32_to_cpu(ddesc->buf_addr),
++ frame_len, DMA_TO_DEVICE);
++ break;
++ case MAP_PAGE:
++ dma_unmap_page(priv->dev,
++ le32_to_cpu(ddesc->buf_addr),
++ frame_len, DMA_TO_DEVICE);
++ break;
++ default:
++ dev_err(priv->dev, "Trying to free an empty slot\n");
++ continue;
++ }
++ dev_kfree_skb_any(priv->txl[i].skb);
++ priv->txl[i].skb = NULL;
++ ddesc->ctl = 0;
++ ddesc->status = DCLEAN;
++ }
++ }
++ priv->tx_slot = 0;
++ priv->tx_dirty = 0;
++}
++
++/* Clean the RX ring */
++static void sun8i_emac_rx_clean(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ int i;
++ struct dma_desc *ddesc;
++
++ /* clean RX ring */
++ for (i = 0; i < priv->nbdesc_rx; i++)
++ if (priv->rx_skb[i]) {
++ ddesc = priv->dd_rx + i;
++ dma_unmap_single(priv->dev,
++ le32_to_cpu(ddesc->buf_addr),
++ DESC_BUF_MAX, DMA_FROM_DEVICE);
++ dev_kfree_skb_any(priv->rx_skb[i]);
++ priv->rx_skb[i] = NULL;
++ }
++}
++
++static int sun8i_emac_stop(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++
++ napi_disable(&priv->napi);
++
++ sun8i_emac_stop_tx(ndev);
++ sun8i_emac_stop_rx(ndev);
++
++ phy_stop(ndev->phydev);
++ phy_disconnect(ndev->phydev);
++
++ sun8i_emac_mdio_unregister(ndev);
++
++ sun8i_emac_unset_syscon(ndev);
++
++ free_irq(priv->irq, ndev);
++
++ sun8i_emac_rx_clean(ndev);
++ sun8i_emac_tx_clean(ndev);
++
++ kfree(priv->rx_skb);
++ kfree(priv->txl);
++
++ dma_free_coherent(priv->dev, priv->nbdesc_rx * sizeof(struct dma_desc),
++ priv->dd_rx, priv->dd_rx_phy);
++ dma_free_coherent(priv->dev, priv->nbdesc_tx * sizeof(struct dma_desc),
++ priv->dd_tx, priv->dd_tx_phy);
++
++ sun8i_emac_unpower(ndev);
++
++ return 0;
++}
++
++static netdev_tx_t sun8i_emac_xmit(struct sk_buff *skb, struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ struct dma_desc *ddesc;
++ struct dma_desc *first;
++ int i = 0, rbd_first;
++ unsigned int len, fraglen, tlen;
++ u32 v;
++ int n;
++ int nf;
++ const skb_frag_t *frag;
++ int do_csum = 0;
++
++ if (skb_put_padto(skb, ETH_ZLEN))
++ return NETDEV_TX_OK;
++ len = skb_headlen(skb);
++
++ n = skb_shinfo(skb)->nr_frags;
++
++ if (skb->ip_summed == CHECKSUM_PARTIAL) {
++ do_csum = 1;
++ priv->estats.tx_hw_csum++;
++ }
++ netif_dbg(priv, tx_queued, ndev, "%s len=%u skblen=%u %x\n", __func__,
++ len, skb->len,
++ (skb->ip_summed == CHECKSUM_PARTIAL));
++
++ /* check for contigous space
++ * We need at least 1(skb->data) + n(numfrags) + 1(one clean slot)
++ */
++ if (rb_tx_numfreedesc(ndev) < n + 2) {
++ dev_err_ratelimited(priv->dev, "BUG!: TX is full %d %d\n",
++ priv->tx_dirty, priv->tx_slot);
++ netif_stop_queue(ndev);
++ return NETDEV_TX_BUSY;
++ }
++ i = priv->tx_slot;
++
++ ddesc = priv->dd_tx + i;
++ first = priv->dd_tx + i;
++ rbd_first = i;
++
++ ddesc->buf_addr = dma_map_single(priv->dev, skb->data, len,
++ DMA_TO_DEVICE);
++ if (dma_mapping_error(priv->dev, ddesc->buf_addr)) {
++ dev_err(priv->dev, "ERROR: Cannot map buffer for DMA\n");
++ goto xmit_error;
++ }
++ /* We cannot direcly use cpu_to_le32() after dma_map_single
++ * since dma_mapping_error use it
++ */
++ ddesc->buf_addr = cpu_to_le32(ddesc->buf_addr);
++ priv->txl[i].map = MAP_SINGLE;
++ priv->txl[i].skb = skb;
++
++ tlen = len;
++ ddesc->ctl = le32_to_cpu(len);
++ /* Undocumented bit that make it works
++ * Without it, packets never be sent on H3 SoC
++ */
++ ddesc->ctl |= EMAC_MAGIC_TX_BIT;
++ if (do_csum)
++ ddesc->ctl |= EMAC_TX_DO_CRC;
++
++ /* handle fragmented skb, one descriptor per fragment */
++ for (nf = 0; nf < n; nf++) {
++ frag = &skb_shinfo(skb)->frags[nf];
++ rb_inc(&i, priv->nbdesc_tx);
++ priv->txl[i].skb = skb;
++ ddesc = priv->dd_tx + i;
++ fraglen = skb_frag_size(frag);
++ ddesc->ctl = le32_to_cpu(fraglen);
++ tlen += fraglen,
++ ddesc->ctl |= EMAC_MAGIC_TX_BIT;
++ if (do_csum)
++ ddesc->ctl |= EMAC_TX_DO_CRC;
++
++ ddesc->buf_addr = skb_frag_dma_map(priv->dev, frag, 0,
++ fraglen, DMA_TO_DEVICE);
++ if (dma_mapping_error(priv->dev, ddesc->buf_addr)) {
++ dev_err(priv->dev, "Cannot map buffer for DMA\n");
++ goto xmit_error;
++ }
++ /* Cannot directly use cpu_to_le32() after skb_frag_dma_map
++ * since dma_mapping_error use it
++ */
++ ddesc->buf_addr = cpu_to_le32(ddesc->buf_addr);
++ priv->txl[i].map = MAP_PAGE;
++ ddesc->status = EMAC_COULD_BE_USED_BY_DMA;
++ }
++
++ /* frame end */
++ ddesc->ctl |= EMAC_DSC_TX_LAST;
++ /* We want an interrupt after transmission */
++ ddesc->ctl |= EMAC_WANT_INT;
++
++ rb_inc(&i, priv->nbdesc_tx);
++
++ /* This line was previously after DMA start, but with that we hit a
++ * small race with complete_xmit() where we complete more data than
++ * sent.
++ * The packet is sent just after EMAC_COULD_BE_USED_BY_DMA flag set and
++ * complete_xmit fire just after before netdev_sent_queue().
++ * This race could be observed only when overflowing a gigabit line.
++ */
++ netdev_sent_queue(ndev, skb->len);
++
++ /* frame begin */
++ first->ctl |= EMAC_DSC_TX_FIRST;
++ wmb();/* EMAC_COULD_BE_USED_BY_DMA must be the last value written */
++ first->status = EMAC_COULD_BE_USED_BY_DMA;
++ priv->tx_slot = i;
++
++ /* Trying to optimize this (recording DMA start/stop) seems
++ * to lead to errors. So we always start DMA.
++ */
++ v = readl(priv->base + EMAC_TX_CTL1);
++ v |= EMAC_TX_DMA_START;
++ v |= EMAC_TX_DMA_EN;
++ writel_relaxed(v, priv->base + EMAC_TX_CTL1);
++
++ if (rb_tx_numfreedesc(ndev) < MAX_SKB_FRAGS + 1) {
++ netif_stop_queue(ndev);
++ priv->estats.tx_stop_queue++;
++ }
++ priv->estats.tx_used_desc = rb_tx_numfreedesc(ndev);
++ priv->ndev->stats.tx_packets++;
++ priv->ndev->stats.tx_bytes += tlen;
++
++ return NETDEV_TX_OK;
++
++xmit_error:
++ /* destroy skb and return TX OK Documentation/DMA-API-HOWTO.txt */
++ /* clean descritors from rbd_first to i */
++ ddesc->ctl = 0;
++ /* setting status to DCLEAN is the last value to be set */
++ wmb();
++ ddesc->status = DCLEAN;
++ do {
++ ddesc = priv->dd_tx + rbd_first;
++ ddesc->ctl = 0;
++ /* setting status to DCLEAN is the last value to be set */
++ wmb();
++ ddesc->status = DCLEAN;
++ rb_inc(&rbd_first, priv->nbdesc_tx);
++ } while (rbd_first != i);
++ dev_kfree_skb_any(skb);
++ return NETDEV_TX_OK;
++}
++
++static int sun8i_emac_change_mtu(struct net_device *ndev, int new_mtu)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ int max_mtu;
++
++ dev_info(priv->dev, "%s set MTU to %d\n", __func__, new_mtu);
++
++ if (netif_running(ndev)) {
++ dev_err(priv->dev, "%s: must be stopped to change its MTU\n",
++ ndev->name);
++ return -EBUSY;
++ }
++
++ max_mtu = SKB_MAX_HEAD(NET_SKB_PAD + NET_IP_ALIGN);
++
++ if ((new_mtu < 68) || (new_mtu > max_mtu)) {
++ dev_err(priv->dev, "%s: invalid MTU, max MTU is: %d\n",
++ ndev->name, max_mtu);
++ return -EINVAL;
++ }
++
++ ndev->mtu = new_mtu;
++ netdev_update_features(ndev);
++ return 0;
++}
++
++static int sun8i_emac_set_features(struct net_device *ndev,
++ netdev_features_t features)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ u32 v;
++
++ v = readl(priv->base + EMAC_BASIC_CTL0);
++ if (features & NETIF_F_LOOPBACK && netif_running(ndev)) {
++ netif_info(priv, hw, ndev, "Set loopback features");
++ v |= BIT(1);
++ } else {
++ netif_info(priv, hw, ndev, "Unset loopback features");
++ v &= ~BIT(1);
++ }
++ writel(v, priv->base + EMAC_BASIC_CTL0);
++
++ v = readl(priv->base + EMAC_RX_CTL0);
++ if (features & NETIF_F_RXCSUM) {
++ v |= EMAC_RX_DO_CRC;
++ netif_info(priv, hw, ndev, "Doing RX CRC check by hardware");
++ } else {
++ v &= ~EMAC_RX_DO_CRC;
++ netif_info(priv, hw, ndev, "No RX CRC check by hardware");
++ }
++ if (features & NETIF_F_RXFCS) {
++ v &= ~EMAC_RX_STRIP_FCS;
++ netif_info(priv, hw, ndev, "Keep FCS");
++ } else {
++ v |= EMAC_RX_STRIP_FCS;
++ netif_info(priv, hw, ndev, "Strip FCS");
++ }
++ writel(v, priv->base + EMAC_RX_CTL0);
++
++ netif_dbg(priv, drv, ndev, "%s %llx %x\n", __func__, features, v);
++
++ return 0;
++}
++
++static void sun8i_emac_set_rx_mode(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ u32 v = 0;
++ int i = 0;
++ struct netdev_hw_addr *ha;
++
++ /* Receive all multicast frames */
++ v |= BIT(16);
++ /* Receive all control frames */
++ v |= BIT(13);
++ if (ndev->flags & IFF_PROMISC)
++ v |= BIT(1);
++ if (netdev_uc_count(ndev) > 7) {
++ v |= BIT(1);
++ } else {
++ netdev_for_each_uc_addr(ha, ndev) {
++ i++;
++ sun8i_emac_set_macaddr(priv, ha->addr, i);
++ }
++ }
++ writel(v, priv->base + EMAC_RX_FRM_FLT);
++}
++
++static void sun8i_emac_tx_timeout(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++
++ netdev_err(ndev, "%s\n", __func__);
++
++ sun8i_emac_stop_tx(ndev);
++
++ sun8i_emac_tx_clean(ndev);
++
++ /* write start of the new TX ring descriptor */
++ writel(priv->dd_tx_phy, priv->base + EMAC_TX_DESC_LIST);
++
++ sun8i_emac_start_tx(ndev);
++
++ netdev_reset_queue(ndev);
++
++ priv->estats.tx_timeout++;
++ ndev->stats.tx_errors++;
++ netif_wake_queue(ndev);
++}
++
++static int sun8i_emac_ioctl(struct net_device *ndev, struct ifreq *rq, int cmd)
++{
++ struct phy_device *phydev = ndev->phydev;
++
++ if (!netif_running(ndev))
++ return -EINVAL;
++
++ if (!phydev)
++ return -ENODEV;
++
++ return phy_mii_ioctl(phydev, rq, cmd);
++}
++
++static int sun8i_emac_check_if_running(struct net_device *ndev)
++{
++ if (!netif_running(ndev))
++ return -EINVAL;
++ return 0;
++}
++
++static int sun8i_emac_get_sset_count(struct net_device *ndev, int sset)
++{
++ switch (sset) {
++ case ETH_SS_STATS:
++ return ARRAY_SIZE(estats_str);
++ }
++ return -EOPNOTSUPP;
++}
++
++static int sun8i_emac_ethtool_get_settings(struct net_device *ndev,
++ struct ethtool_cmd *cmd)
++{
++ struct phy_device *phy = ndev->phydev;
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++
++ if (!phy) {
++ netdev_err(ndev, "%s: %s: PHY is not registered\n",
++ __func__, ndev->name);
++ return -ENODEV;
++ }
++
++ if (!netif_running(ndev)) {
++ dev_err(priv->dev, "interface disabled: we cannot track link speed / duplex setting\n");
++ return -EBUSY;
++ }
++
++ return phy_ethtool_gset(phy, cmd);
++}
++
++static int sun8i_emac_ethtool_set_settings(struct net_device *ndev,
++ struct ethtool_cmd *cmd)
++{
++ struct phy_device *phy = ndev->phydev;
++
++ return phy_ethtool_sset(phy, cmd);
++}
++
++static void sun8i_emac_ethtool_getdrvinfo(struct net_device *ndev,
++ struct ethtool_drvinfo *info)
++{
++ strlcpy(info->driver, "sun8i_emac", sizeof(info->driver));
++ strcpy(info->version, "00");
++ info->fw_version[0] = '\0';
++}
++
++static void sun8i_emac_ethtool_stats(struct net_device *ndev,
++ struct ethtool_stats *dummy, u64 *data)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++
++ memcpy(data, &priv->estats,
++ sun8i_emac_get_sset_count(ndev, ETH_SS_STATS) * sizeof(u64));
++}
++
++static void sun8i_emac_ethtool_strings(struct net_device *dev, u32 stringset,
++ u8 *buffer)
++{
++ switch (stringset) {
++ case ETH_SS_STATS:
++ memcpy(buffer, &estats_str, sizeof(estats_str));
++ break;
++ }
++}
++
++static u32 sun8i_emac_ethtool_getmsglevel(struct net_device *ndev)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++
++ return priv->msg_enable;
++}
++
++static void sun8i_emac_ethtool_setmsglevel(struct net_device *ndev, u32 level)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++
++ priv->msg_enable = level;
++}
++
++static void sun8i_emac_get_pauseparam(struct net_device *ndev,
++ struct ethtool_pauseparam *pause)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++
++ pause->rx_pause = 0;
++ pause->tx_pause = 0;
++ pause->autoneg = ndev->phydev->autoneg;
++
++ if (priv->flow_ctrl & EMAC_FLOW_RX)
++ pause->rx_pause = 1;
++ if (priv->flow_ctrl & EMAC_FLOW_TX)
++ pause->tx_pause = 1;
++}
++
++static int sun8i_emac_set_pauseparam(struct net_device *ndev,
++ struct ethtool_pauseparam *pause)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ struct phy_device *phy = ndev->phydev;
++ int new_pause = 0;
++ int ret = 0;
++
++ if (pause->rx_pause)
++ new_pause |= EMAC_FLOW_RX;
++ if (pause->tx_pause)
++ new_pause |= EMAC_FLOW_TX;
++
++ priv->flow_ctrl = new_pause;
++ phy->autoneg = pause->autoneg;
++
++ if (phy->autoneg) {
++ if (netif_running(ndev))
++ ret = phy_start_aneg(phy);
++ } else {
++ sun8i_emac_flow_ctrl(priv, phy->duplex, priv->flow_ctrl);
++ }
++ return ret;
++}
++
++static void sun8i_emac_ethtool_get_ringparam(struct net_device *ndev,
++ struct ethtool_ringparam *ring)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++
++ ring->rx_pending = priv->nbdesc_rx;
++ ring->tx_pending = priv->nbdesc_tx;
++}
++
++static int sun8i_emac_ethtool_set_ringparam(struct net_device *ndev,
++ struct ethtool_ringparam *ring)
++{
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ int err;
++
++ if (ring->rx_max_pending || ring->rx_mini_max_pending ||
++ ring->rx_jumbo_max_pending || ring->rx_mini_pending ||
++ ring->rx_jumbo_pending || ring->tx_max_pending)
++ return -EINVAL;
++
++ if (ring->tx_pending < MAX_SKB_FRAGS + 1) {
++ netdev_err(ndev, "The number of TX descriptors is too low");
++ return -EINVAL;
++ }
++
++ sun8i_emac_stop_tx(ndev);
++ sun8i_emac_stop_rx(ndev);
++
++ sun8i_emac_rx_clean(ndev);
++ sun8i_emac_tx_clean(ndev);
++
++ kfree(priv->rx_skb);
++ kfree(priv->txl);
++
++ dma_free_coherent(priv->dev, priv->nbdesc_rx * sizeof(struct dma_desc),
++ priv->dd_rx, priv->dd_rx_phy);
++ dma_free_coherent(priv->dev, priv->nbdesc_tx * sizeof(struct dma_desc),
++ priv->dd_tx, priv->dd_tx_phy);
++
++ priv->nbdesc_rx = ring->rx_pending;
++ priv->nbdesc_tx = ring->tx_pending;
++ err = sun8i_emac_alloc_rings(ndev);
++ if (err) {
++ /* Fatal error, we cannot re start */
++ netdev_err(ndev, "Fail to allocate rings\n");
++ return -EFAULT;
++ }
++
++ sun8i_emac_start_rx(ndev);
++ sun8i_emac_start_tx(ndev);
++
++ netif_start_queue(ndev);
++
++ netdev_info(ndev, "Ring Param settings: rx: %d, tx %d\n",
++ ring->rx_pending, ring->tx_pending);
++ return 0;
++}
++
++static const struct ethtool_ops sun8i_emac_ethtool_ops = {
++ .begin = sun8i_emac_check_if_running,
++ .get_settings = sun8i_emac_ethtool_get_settings,
++ .set_settings = sun8i_emac_ethtool_set_settings,
++ .get_link = ethtool_op_get_link,
++ .get_pauseparam = sun8i_emac_get_pauseparam,
++ .set_pauseparam = sun8i_emac_set_pauseparam,
++ .get_ethtool_stats = sun8i_emac_ethtool_stats,
++ .get_strings = sun8i_emac_ethtool_strings,
++ .get_sset_count = sun8i_emac_get_sset_count,
++ .get_drvinfo = sun8i_emac_ethtool_getdrvinfo,
++ .get_msglevel = sun8i_emac_ethtool_getmsglevel,
++ .set_msglevel = sun8i_emac_ethtool_setmsglevel,
++ .get_ringparam = sun8i_emac_ethtool_get_ringparam,
++ .set_ringparam = sun8i_emac_ethtool_set_ringparam,
++};
++
++static const struct net_device_ops sun8i_emac_netdev_ops = {
++ .ndo_init = sun8i_emac_init,
++ .ndo_open = sun8i_emac_open,
++ .ndo_start_xmit = sun8i_emac_xmit,
++ .ndo_stop = sun8i_emac_stop,
++ .ndo_change_mtu = sun8i_emac_change_mtu,
++ .ndo_set_features = sun8i_emac_set_features,
++ .ndo_set_rx_mode = sun8i_emac_set_rx_mode,
++ .ndo_tx_timeout = sun8i_emac_tx_timeout,
++ .ndo_do_ioctl = sun8i_emac_ioctl,
++ .ndo_set_mac_address = eth_mac_addr,
++};
++
++/* No locking in this function since it is guaranteed to be run once and
++ * do actions only done here:
++ * - Scheduling NAPI
++ * - Stopping interrupts
++ * - Updating stats
++ *
++ * Even when not enabled via EMAC_INT_EN, some interrupt could fire, so we need
++ * to handle all of them.
++ * Interrupts know to fire when not enabled are:
++ * - EMAC_TX_DMA_STOP_INT
++ * - EMAC_TX_BUF_UA_INT
++ * - EMAC_TX_EARLY_INT
++ * - EMAC_RX_BUF_UA_INT
++ * - EMAC_RX_EARLY_INT
++ */
++static irqreturn_t sun8i_emac_dma_interrupt(int irq, void *dev_id)
++{
++ struct net_device *ndev = dev_id;
++ struct sun8i_emac_priv *priv = netdev_priv(ndev);
++ u32 v, u;
++
++ v = readl(priv->base + EMAC_INT_STA);
++
++ /* When this bit is asserted, a frame transmission is completed. */
++ if (v & EMAC_TX_INT) {
++ priv->estats.tx_int++;
++ writel(0, priv->base + EMAC_INT_EN);
++ napi_schedule(&priv->napi);
++ }
++
++ /* When this bit is asserted, the TX DMA FSM is stopped.
++ * For the moment only a call to tx_timeout cause this interrupt
++ * to fire.
++ */
++ if (v & EMAC_TX_DMA_STOP_INT)
++ priv->estats.tx_dma_stop++;
++
++ /* When this asserted, the TX DMA can not acquire next TX descriptor
++ * and TX DMA FSM is suspended.
++ */
++ if (v & EMAC_TX_BUF_UA_INT) {
++ priv->estats.tx_dma_ua++;
++ writel(0, priv->base + EMAC_INT_EN);
++ napi_schedule(&priv->napi);
++ }
++
++ if (v & EMAC_TX_TIMEOUT_INT)
++ priv->estats.tx_timeout_int++;
++
++ if (v & EMAC_TX_UNDERFLOW_INT)
++ priv->estats.tx_underflow_int++;
++
++ /* When this bit asserted , the frame is transmitted to FIFO totally. */
++ if (v & EMAC_TX_EARLY_INT)
++ priv->estats.tx_early_int++;
++
++ /* When this bit is asserted, a frame reception is completed */
++ if (v & EMAC_RX_INT) {
++ priv->estats.rx_int++;
++ writel(0, priv->base + EMAC_INT_EN);
++ napi_schedule(&priv->napi);
++ }
++
++ /* When this asserted, the RX DMA can not acquire next RX descriptor
++ * and RX DMA FSM is suspended.
++ */
++ if (v & EMAC_RX_BUF_UA_INT) {
++ u = readl(priv->base + EMAC_RX_CTL1);
++ writel(u | EMAC_RX_DMA_START, priv->base + EMAC_RX_CTL1);
++ priv->estats.rx_dma_ua++;
++ }
++
++ /* Same as TX DMA STOP, but never hit it */
++ if (v & EMAC_RX_DMA_STOP_INT)
++ priv->estats.rx_dma_stop++;
++
++ if (v & EMAC_RX_TIMEOUT_INT)
++ priv->estats.rx_timeout_int++;
++
++ if (v & EMAC_RX_OVERFLOW_INT)
++ priv->estats.rx_overflow_int++;
++
++ if (v & EMAC_RX_EARLY_INT)
++ priv->estats.rx_early_int++;
++
++ if (v & EMAC_RGMII_STA_INT)
++ priv->estats.rgmii_state_int++;
++
++ /* the datasheet state those register as read-only
++ * but nothing work(freeze) without writing to it
++ */
++ writel(v, priv->base + EMAC_INT_STA);
++
++ return IRQ_HANDLED;
++}
++
++static int sun8i_emac_probe(struct platform_device *pdev)
++{
++ struct device_node *node = pdev->dev.of_node;
++ struct sun8i_emac_priv *priv;
++ struct net_device *ndev;
++ struct resource *res;
++ int ret;
++
++ ndev = alloc_etherdev(sizeof(*priv));
++ if (!ndev)
++ return -ENOMEM;
++
++ SET_NETDEV_DEV(ndev, &pdev->dev);
++ priv = netdev_priv(ndev);
++ platform_set_drvdata(pdev, ndev);
++
++ priv->variant = of_device_get_match_data(&pdev->dev);
++ if (!priv->variant) {
++ dev_err(&pdev->dev, "Missing sun8i-emac variant\n");
++ return -EINVAL;
++ }
++
++ priv->mdio_node = of_get_child_by_name(node, "mdio");
++ if (!priv->mdio_node) {
++ netdev_err(ndev, "Could not find a MDIO node\n");
++ return -EINVAL;
++ }
++
++ priv->phy_node = of_parse_phandle(node, "phy-handle", 0);
++ if (!priv->phy_node) {
++ netdev_err(ndev, "No associated PHY\n");
++ return -EINVAL;
++ }
++
++ priv->regmap = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
++ "syscon");
++ if (IS_ERR(priv->regmap)) {
++ ret = PTR_ERR(priv->regmap);
++ dev_err(&pdev->dev, "unable to map SYSCON:%d\n", ret);
++ return ret;
++ }
++
++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ priv->base = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(priv->base)) {
++ ret = PTR_ERR(priv->base);
++ dev_err(&pdev->dev, "Cannot request MMIO: %d\n", ret);
++ return ret;
++ }
++
++ priv->ahb_clk = devm_clk_get(&pdev->dev, "ahb");
++ if (IS_ERR(priv->ahb_clk)) {
++ ret = PTR_ERR(priv->ahb_clk);
++ dev_err(&pdev->dev, "Cannot get AHB clock err=%d\n", ret);
++ goto probe_err;
++ }
++
++ priv->rst_mac = devm_reset_control_get_optional(&pdev->dev, "ahb");
++ if (IS_ERR(priv->rst_mac)) {
++ ret = PTR_ERR(priv->rst_mac);
++ if (ret == -EPROBE_DEFER)
++ return -EPROBE_DEFER;
++ dev_info(&pdev->dev, "No MAC reset control found %d\n", ret);
++ priv->rst_mac = NULL;
++ }
++
++ priv->phy_interface = of_get_phy_mode(node);
++ if (priv->phy_interface < 0) {
++ netdev_err(ndev, "PHY interface mode node unspecified\n");
++ return priv->phy_interface;
++ }
++
++ switch (priv->phy_interface) {
++ case PHY_INTERFACE_MODE_MII:
++ if (!priv->variant->support_mii)
++ return -EINVAL;
++ break;
++ case PHY_INTERFACE_MODE_RMII:
++ if (!priv->variant->support_rmii)
++ return -EINVAL;
++ break;
++ case PHY_INTERFACE_MODE_RGMII:
++ if (!priv->variant->support_rgmii)
++ return -EINVAL;
++ break;
++ default:
++ netdev_err(ndev, "Unsupported interface mode: %s",
++ phy_modes(priv->phy_interface));
++ return -EINVAL;
++ }
++
++ if (priv->phy_interface == priv->variant->internal_phy)
++ priv->use_internal_phy = true;
++
++ if (priv->use_internal_phy) {
++ priv->ephy_clk = of_clk_get(priv->phy_node, 0);
++ if (IS_ERR(priv->ephy_clk)) {
++ ret = PTR_ERR(priv->ephy_clk);
++ dev_err(&pdev->dev, "Cannot get EPHY clock err=%d\n",
++ ret);
++ goto probe_err;
++ }
++
++ priv->rst_ephy = of_reset_control_get(priv->phy_node, 0);
++ if (IS_ERR(priv->rst_ephy)) {
++ ret = PTR_ERR(priv->rst_ephy);
++ if (ret == -EPROBE_DEFER)
++ goto probe_err;
++ dev_info(&pdev->dev,
++ "No EPHY reset control found %d\n", ret);
++ priv->rst_ephy = NULL;
++ }
++ }
++
++ priv->irq = platform_get_irq(pdev, 0);
++ if (priv->irq < 0) {
++ ret = priv->irq;
++ dev_err(&pdev->dev, "Cannot claim IRQ: %d\n", ret);
++ goto probe_err;
++ }
++
++ spin_lock_init(&priv->tx_lock);
++
++ ndev->netdev_ops = &sun8i_emac_netdev_ops;
++ ndev->ethtool_ops = &sun8i_emac_ethtool_ops;
++
++ priv->ndev = ndev;
++ priv->dev = &pdev->dev;
++
++ ndev->hw_features = NETIF_F_SG | NETIF_F_HIGHDMA;
++ ndev->hw_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM |
++ NETIF_F_RXCSUM;
++ ndev->features |= ndev->hw_features;
++ ndev->hw_features |= NETIF_F_RXFCS;
++ ndev->hw_features |= NETIF_F_RXALL;
++ ndev->hw_features |= NETIF_F_LOOPBACK;
++ ndev->priv_flags |= IFF_UNICAST_FLT;
++
++ ndev->watchdog_timeo = msecs_to_jiffies(5000);
++ netif_carrier_off(ndev);
++
++ /* Benched on OPIPC with 100M, setting more than 256 does not give any
++ * perf boost
++ */
++ priv->nbdesc_rx = 128;
++ priv->nbdesc_tx = 256;
++
++ ret = register_netdev(ndev);
++ if (ret) {
++ dev_err(&pdev->dev, "ERROR: Register %s failed\n", ndev->name);
++ goto probe_err;
++ }
++
++ return 0;
++
++probe_err:
++ free_netdev(ndev);
++ return ret;
++}
++
++static int sun8i_emac_remove(struct platform_device *pdev)
++{
++ struct net_device *ndev = platform_get_drvdata(pdev);
++
++ unregister_netdev(ndev);
++ platform_set_drvdata(pdev, NULL);
++ free_netdev(ndev);
++
++ return 0;
++}
++
++static const struct of_device_id sun8i_emac_of_match_table[] = {
++ { .compatible = "allwinner,sun8i-a83t-emac",
++ .data = &emac_variant_a83t },
++ { .compatible = "allwinner,sun8i-h3-emac",
++ .data = &emac_variant_h3 },
++ { .compatible = "allwinner,sun50i-a64-emac",
++ .data = &emac_variant_a64 },
++ {}
++};
++MODULE_DEVICE_TABLE(of, sun8i_emac_of_match_table);
++
++static struct platform_driver sun8i_emac_driver = {
++ .probe = sun8i_emac_probe,
++ .remove = sun8i_emac_remove,
++ .driver = {
++ .name = "sun8i-emac",
++ .of_match_table = sun8i_emac_of_match_table,
++ },
++};
++
++module_platform_driver(sun8i_emac_driver);
++
++MODULE_DESCRIPTION("sun8i Ethernet driver");
++MODULE_LICENSE("GPL");
++MODULE_AUTHOR("Corentin Labbe <clabbe.montjoie@gmail.com");
+--
+2.9.3
+
+From 1d9ea1f4df27f3a2e2ed7094852a23a4dd45e2be Mon Sep 17 00:00:00 2001
+From: Corentin LABBE <clabbe.montjoie@gmail.com>
+Date: Fri, 7 Oct 2016 10:25:49 +0200
+Subject: [PATCH 2/8] MAINTAINERS: Add myself as maintainer of sun8i-emac
+
+This patch add myself as maintainer of the sun8i-emac driver.
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+---
+ MAINTAINERS | 6 ++++++
+ 1 file changed, 6 insertions(+)
+
+diff --git a/MAINTAINERS b/MAINTAINERS
+index 411e3b8..e99a087 100644
+--- a/MAINTAINERS
++++ b/MAINTAINERS
+@@ -590,6 +590,12 @@ S: Maintained
+ F: Documentation/i2c/busses/i2c-ali1563
+ F: drivers/i2c/busses/i2c-ali1563.c
+
++ALLWINNER SUN8I-EMAC ETHERNET DRIVER
++M: Corentin Labbe <clabbe.montjoie@gmail.com>
++L: netdev@vger.kernel.org
++S: Maintained
++F: drivers/net/ethernet/allwinner/sun8i-emac.c
++
+ ALLWINNER SECURITY SYSTEM
+ M: Corentin Labbe <clabbe.montjoie@gmail.com>
+ L: linux-crypto@vger.kernel.org
+--
+2.9.3
+
+From 6b3093e31b877f39475454b5af3b820dbb3a4f73 Mon Sep 17 00:00:00 2001
+From: Corentin LABBE <clabbe.montjoie@gmail.com>
+Date: Fri, 7 Oct 2016 10:25:50 +0200
+Subject: [PATCH 3/8] ARM: sun8i: dt: Add DT bindings documentation for
+ Allwinner sun8i-emac
+
+This patch adds documentation for Device-Tree bindings for the
+Allwinner sun8i-emac driver.
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+---
+ .../bindings/net/allwinner,sun8i-emac.txt | 70 ++++++++++++++++++++++
+ 1 file changed, 70 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt
+
+diff --git a/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt
+new file mode 100644
+index 0000000..92e4ef3b
+--- /dev/null
++++ b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt
+@@ -0,0 +1,70 @@
++* Allwinner sun8i EMAC ethernet controller
++
++Required properties:
++- compatible: should be one of the following string:
++ "allwinner,sun8i-a83t-emac"
++ "allwinner,sun8i-h3-emac"
++ "allwinner,sun50i-a64-emac"
++- reg: address and length of the register for the device.
++- syscon: A phandle to the syscon of the SoC
++- interrupts: interrupt for the device
++- clocks: A phandle to the reference clock for this device
++- clock-names: should be "ahb"
++- resets: A phandle to the reset control for this device
++- reset-names: should be "ahb"
++- phy-mode: See ethernet.txt
++- phy-handle: See ethernet.txt
++- #address-cells: shall be 1
++- #size-cells: shall be 0
++
++Optional properties:
++- allwinner,tx-delay: TX clock delay chain value. Range value is 0-0x07. Default is 0)
++- allwinner,rx-delay: RX clock delay chain value. Range value is 0-0x1F. Default is 0)
++Both delay properties does not have units, there are arbitrary value.
++The TX/RX clock delay chain settings are board specific and could be found
++in vendor FEX files.
++
++Optional properties for "allwinner,sun8i-h3-emac":
++- allwinner,leds-active-low: EPHY LEDs are active low
++
++Required child node of emac:
++- mdio bus node: should be named mdio
++
++Required properties of the mdio node:
++- #address-cells: shall be 1
++- #size-cells: shall be 0
++
++The device node referenced by "phy" or "phy-handle" should be a child node
++of the mdio node. See phy.txt for the generic PHY bindings.
++
++Required properties of the phy node with "allwinner,sun8i-h3-emac":
++- clocks: an extra phandle to the reference clock for the EPHY
++- resets: an extra phandle to the reset control for the EPHY
++
++Example:
++
++emac: ethernet@01c0b000 {
++ compatible = "allwinner,sun8i-h3-emac";
++ syscon = <&syscon>;
++ reg = <0x01c0b000 0x104>;
++ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
++ resets = <&ccu RST_BUS_EMAC>;
++ reset-names = "ahb";
++ clocks = <&ccu CLK_BUS_EMAC>;
++ clock-names = "ahb";
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ phy = <&int_mii_phy>;
++ phy-mode = "mii";
++ allwinner,leds-active-low;
++ mdio: mdio {
++ #address-cells = <1>;
++ #size-cells = <0>;
++ int_mii_phy: ethernet-phy@1 {
++ reg = <1>;
++ clocks = <&ccu CLK_BUS_EPHY>;
++ resets = <&ccu RST_BUS_EPHY>;
++ };
++ };
++};
+--
+2.9.3
+
+From aa634aa1b0454befe54a14d03b9a3ba6f750dcfd Mon Sep 17 00:00:00 2001
+From: Corentin LABBE <clabbe.montjoie@gmail.com>
+Date: Fri, 7 Oct 2016 10:25:51 +0200
+Subject: [PATCH 4/8] ARM: dts: sun8i-h3: Add dt node for the syscon control
+ module
+
+This patch add the dt node for the syscon register present on the
+Allwinner H3.
+
+Only two register are present in this syscon and the only one useful is
+the one dedicated to EMAC clock.
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+---
+ arch/arm/boot/dts/sun8i-h3.dtsi | 5 +++++
+ 1 file changed, 5 insertions(+)
+
+diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
+index 75a8654..eac7d00 100644
+--- a/arch/arm/boot/dts/sun8i-h3.dtsi
++++ b/arch/arm/boot/dts/sun8i-h3.dtsi
+@@ -140,6 +140,11 @@
+ #size-cells = <1>;
+ ranges;
+
++ syscon: syscon@01c00000 {
++ compatible = "syscon";
++ reg = <0x01c00000 0x1000>;
++ };
++
+ dma: dma-controller@01c02000 {
+ compatible = "allwinner,sun8i-h3-dma";
+ reg = <0x01c02000 0x1000>;
+--
+2.9.3
+
+From 976cca2d4eb5bf85c26dfaad03ea70bff88981fd Mon Sep 17 00:00:00 2001
+From: Peter Robinson <pbrobinson@gmail.com>
+Date: Tue, 8 Nov 2016 10:23:08 +0000
+Subject: [PATCH 5/8] ARM: dts: sun8i-h3: add sun8i-emac ethernet driver
+
+The sun8i-emac is an ethernet MAC hardware that support 10/100/1000
+speed.
+
+This patch enable the sun8i-emac on the Allwinner H3 SoC Device-tree.
+The SoC H3 have an internal PHY, so optionals syscon and ephy are set.
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+---
+ arch/arm/boot/dts/sun8i-h3.dtsi | 24 ++++++++++++++++++++++++
+ 1 file changed, 24 insertions(+)
+
+diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
+index eac7d00..86a8665 100644
+--- a/arch/arm/boot/dts/sun8i-h3.dtsi
++++ b/arch/arm/boot/dts/sun8i-h3.dtsi
+@@ -535,6 +535,30 @@
+ #size-cells = <0>;
+ };
+
++ emac: ethernet@1c30000 {
++ compatible = "allwinner,sun8i-h3-emac";
++ syscon = <&syscon>;
++ reg = <0x01c30000 0x104>;
++ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
++ resets = <&ccu RST_BUS_EMAC>;
++ reset-names = "ahb";
++ clocks = <&ccu CLK_BUS_EMAC>;
++ clock-names = "ahb";
++ #address-cells = <1>;
++ #size-cells = <0>;
++ status = "disabled";
++
++ mdio: mdio {
++ #address-cells = <1>;
++ #size-cells = <0>;
++ int_mii_phy: ethernet-phy@1 {
++ reg = <1>;
++ clocks = <&ccu CLK_BUS_EPHY>;
++ resets = <&ccu RST_BUS_EPHY>;
++ };
++ };
++ };
++
+ gic: interrupt-controller@01c81000 {
+ compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ reg = <0x01c81000 0x1000>,
+--
+2.9.3
+
+From 6e483713dda9e0d5e8e5f37d8b0367ff216c53db Mon Sep 17 00:00:00 2001
+From: Corentin LABBE <clabbe.montjoie@gmail.com>
+Date: Fri, 7 Oct 2016 10:25:53 +0200
+Subject: [PATCH 6/8] ARM: dts: sun8i: Enable sun8i-emac on the Orange PI PC
+
+The sun8i-emac hardware is present on the Orange PI PC.
+It uses the internal PHY.
+
+This patch create the needed emac node.
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+---
+ arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 8 ++++++++
+ 1 file changed, 8 insertions(+)
+
+diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
+index 3ec9712..1b8dbc0 100644
+--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
++++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
+@@ -54,6 +54,7 @@
+
+ aliases {
+ serial0 = &uart0;
++ ethernet0 = &emac;
+ };
+
+ chosen {
+@@ -183,3 +184,10 @@
+ /* USB VBUS is always on */
+ status = "okay";
+ };
++
++&emac {
++ phy-handle = <&int_mii_phy>;
++ phy-mode = "mii";
++ allwinner,leds-active-low;
++ status = "okay";
++};
+--
+2.9.3
+
+From 05cf4e2c77424ad5c9dc8495a65d6695d2831b0a Mon Sep 17 00:00:00 2001
+From: Hans de Goede <hdegoede@redhat.com>
+Date: Fri, 7 Oct 2016 10:25:54 +0200
+Subject: [PATCH 7/8] ARM: dts: sun8i: Enable sun8i-emac on the Orange PI One
+
+The sun8i-emac hardware is present on the Orange PI One.
+It uses the internal PHY.
+
+This patch create the needed emac node.
+
+Signed-off-by: Hans de Goede <hdegoede@redhat.com>
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+---
+ arch/arm/boot/dts/sun8i-h3-orangepi-one.dts | 8 ++++++++
+ 1 file changed, 8 insertions(+)
+
+diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
+index 5c9b5bf..fa398cc 100644
+--- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
++++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
+@@ -54,6 +54,7 @@
+
+ aliases {
+ serial0 = &uart0;
++ ethernet0 = &emac;
+ };
+
+ chosen {
+@@ -94,6 +95,13 @@
+ status = "okay";
+ };
+
++&emac {
++ phy-handle = <&int_mii_phy>;
++ phy-mode = "mii";
++ allwinner,leds-active-low;
++ status = "okay";
++};
++
+ &mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+--
+2.9.3
+
+From 52c300b614fcb29e81067aa7ed8aafa489b590b7 Mon Sep 17 00:00:00 2001
+From: Peter Robinson <pbrobinson@gmail.com>
+Date: Tue, 8 Nov 2016 10:24:42 +0000
+Subject: [PATCH 8/8] ARM: dts: sun8i: Enable sun8i-emac on the Orange Pi 2
+
+The sun8i-emac hardware is present on the Orange PI 2.
+It uses the internal PHY.
+
+This patch create the needed emac node.
+
+Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
+---
+ arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 8 ++++++++
+ 1 file changed, 8 insertions(+)
+
+diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
+index e5bcaba..ad66b61 100644
+--- a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
++++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
+@@ -54,6 +54,7 @@
+
+ aliases {
+ serial0 = &uart0;
++ ethernet0 = &emac;
+ /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+ ethernet1 = &rtl8189;
+ };
+@@ -212,3 +213,10 @@
+ usb1_vbus-supply = <&reg_usb1_vbus>;
+ status = "okay";
+ };
++
++&emac {
++ phy-handle = <&int_mii_phy>;
++ phy-mode = "mii";
++ allwinner,leds-active-low;
++ status = "okay";
++};
+--
+2.9.3
+
diff --git a/bcm283x-vc4-fixes.patch b/bcm283x-vc4-fixes.patch
new file mode 100644
index 000000000..d42ceb62a
--- /dev/null
+++ b/bcm283x-vc4-fixes.patch
@@ -0,0 +1,43 @@
+From 30772942cc1095c3129eecfa182e2c568e566b9d Mon Sep 17 00:00:00 2001
+From: Dan Carpenter <dan.carpenter@oracle.com>
+Date: Thu, 13 Oct 2016 11:54:31 +0300
+Subject: [PATCH] drm/vc4: Fix a couple error codes in vc4_cl_lookup_bos()
+
+If the allocation fails the current code returns success. If
+copy_from_user() fails it returns the number of bytes remaining instead
+of -EFAULT.
+
+Fixes: d5b1a78a772f ("drm/vc4: Add support for drawing 3D frames.")
+Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
+Reviewed-by: Eric Anholt <eric@anholt.net>
+---
+ drivers/gpu/drm/vc4/vc4_gem.c | 9 +++++----
+ 1 file changed, 5 insertions(+), 4 deletions(-)
+
+diff --git a/drivers/gpu/drm/vc4/vc4_gem.c b/drivers/gpu/drm/vc4/vc4_gem.c
+index ae1609e..4050540 100644
+--- a/drivers/gpu/drm/vc4/vc4_gem.c
++++ b/drivers/gpu/drm/vc4/vc4_gem.c
+@@ -548,14 +548,15 @@ vc4_cl_lookup_bos(struct drm_device *dev,
+
+ handles = drm_malloc_ab(exec->bo_count, sizeof(uint32_t));
+ if (!handles) {
++ ret = -ENOMEM;
+ DRM_ERROR("Failed to allocate incoming GEM handles\n");
+ goto fail;
+ }
+
+- ret = copy_from_user(handles,
+- (void __user *)(uintptr_t)args->bo_handles,
+- exec->bo_count * sizeof(uint32_t));
+- if (ret) {
++ if (copy_from_user(handles,
++ (void __user *)(uintptr_t)args->bo_handles,
++ exec->bo_count * sizeof(uint32_t))) {
++ ret = -EFAULT;
+ DRM_ERROR("Failed to copy in GEM handles\n");
+ goto fail;
+ }
+--
+2.9.3
+
diff --git a/config-arm64 b/config-arm64
index 983eafb89..c1a4bce6a 100644
--- a/config-arm64
+++ b/config-arm64
@@ -198,6 +198,7 @@ CONFIG_TEGRA_ACONNECT=m
CONFIG_SUNXI_RSB=m
CONFIG_AHCI_SUNXI=m
CONFIG_NET_VENDOR_ALLWINNER=y
+CONFIG_SUN8I_EMAC=m
# CONFIG_SUN4I_EMAC is not set
# CONFIG_MDIO_SUN4I is not set
# CONFIG_KEYBOARD_SUN4I_LRADC is not set
diff --git a/config-armv7-generic b/config-armv7-generic
index 5d1006372..db6496b2d 100644
--- a/config-armv7-generic
+++ b/config-armv7-generic
@@ -225,6 +225,7 @@ CONFIG_IR_SUNXI=m
CONFIG_MDIO_SUN4I=m
CONFIG_DWMAC_SUNXI=m
CONFIG_SUN4I_EMAC=m
+CONFIG_SUN8I_EMAC=m
CONFIG_RTC_DRV_SUN6I=m
CONFIG_MTD_NAND_SUNXI=m
CONFIG_SERIO_SUN4I_PS2=m
diff --git a/kernel.spec b/kernel.spec
index 8256b8085..025b07d75 100644
--- a/kernel.spec
+++ b/kernel.spec
@@ -523,6 +523,10 @@ Patch430: ARM-tegra-usb-no-reset.patch
Patch431: bcm2837-initial-support.patch
+Patch432: bcm283x-vc4-fixes.patch
+
+Patch433: AllWinner-net-emac.patch
+
Patch460: lib-cpumask-Make-CPUMASK_OFFSTACK-usable-without-deb.patch
Patch466: input-kill-stupid-messages.patch
@@ -2154,6 +2158,9 @@ fi
#
#
%changelog
+* Tue Nov 8 2016 Peter Robinson <pbrobinson@fedoraproject.org>
+- Sync some ARM patches from F-25 branch
+
* Mon Nov 07 2016 Laura Abbott <labbott@redhat.com>
- Enable CONFIG_EXT4_ENCRYPTION (rhbz 1389509)
- Enable CONFIG_NFSD_FLEXFILELAYOUT
generated by cgit (git 2.34.1) at 2024-11-19 13:44:38 +0000