diff options
Diffstat (limited to 'doc')
| -rw-r--r-- | doc/rsyslog_conf_filter.html | 2 | ||||
| -rw-r--r-- | doc/rsyslog_conf_global.html | 4 | ||||
| -rw-r--r-- | doc/rsyslog_conf_templates.html | 3 |
3 files changed, 4 insertions, 5 deletions
diff --git a/doc/rsyslog_conf_filter.html b/doc/rsyslog_conf_filter.html index 841ec9c7..63c29817 100644 --- a/doc/rsyslog_conf_filter.html +++ b/doc/rsyslog_conf_filter.html @@ -231,7 +231,7 @@ A few quick samples:<br> <br> <code> *.* /var/log/file1 # the traditional way<br> -if $msg contains 'error' /var/log/errlog # the expression-based way<br> +if $msg contains 'error' then /var/log/errlog # the expression-based way<br> </code> <br> Right now, you need to specify numerical values if you would like to diff --git a/doc/rsyslog_conf_global.html b/doc/rsyslog_conf_global.html index 7d223c1b..ca0c9941 100644 --- a/doc/rsyslog_conf_global.html +++ b/doc/rsyslog_conf_global.html @@ -236,7 +236,7 @@ in that case by sending rsyslogd a HUP signal. of the output file. The higher the number, the better the compression, but also the more CPU is required for zipping.</li> <li><b>$OMFileIOBufferSize</b> <size_nbr>, default 4k, size of the buffer used to writing output data. The larger the buffer, the potentially better performance is. The default of 4k is quite conservative, it is useful to go up to 64k, and 128K if you used gzip compression (then, even higher sizes may make sense)</li> -<li><b>$OMFileFlushOnTXEnd</b> <[on/<b>off</b>]>, default ff. Omfile has the +<li><b>$OMFileFlushOnTXEnd</b> <[<b>on</b>/off]>, default on. Omfile has the capability to write output using a buffered writer. Disk writes are only done when the buffer is full. So if an error happens during that write, data is potentially lost. In cases where @@ -244,7 +244,7 @@ this is unacceptable, set $OMFileFlushOnTXEnd to on. Then, data is written at th of each transaction (for pre-v5 this means after <b>each</b> log message) and the usual error recovery thus can handle write errors without data loss. Note that this option severely reduces the effect of zip compression and should be switched to off -for that use case. Note that the default -off- is primarily an aid to preserve +for that use case. Note that the default -on- is primarily an aid to preserve the traditional syslogd behaviour.</li> <li><a href="rsconf1_omfileforcechown.html">$omfileForceChown</a> - force ownership change for all files</li> <li><b>$RepeatedMsgContainsOriginalMsg</b> [on/<b>off</b>] - "last message repeated n times" messages, if generated, diff --git a/doc/rsyslog_conf_templates.html b/doc/rsyslog_conf_templates.html index 6c68b801..baa4ce29 100644 --- a/doc/rsyslog_conf_templates.html +++ b/doc/rsyslog_conf_templates.html @@ -87,8 +87,7 @@ option. Otherwise you will become vulnerable to SQL injection. <br> To escape:<br> % = \%<br> \ = \\ --> '\' is used to escape (as in C)<br> -$template TraditionalFormat,%timegenerated% %HOSTNAME% -%syslogtag%%msg%\n"<br> +$template TraditionalFormat,"%timegenerated% %HOSTNAME% %syslogtag%%msg%\n"<br> <br> Properties can be accessed by the <a href="property_replacer.html">property replacer</a> (see there for details).</p> |