diff options
Diffstat (limited to 'doc/rsyslog_conf_global.html')
| -rw-r--r-- | doc/rsyslog_conf_global.html | 29 |
1 files changed, 14 insertions, 15 deletions
diff --git a/doc/rsyslog_conf_global.html b/doc/rsyslog_conf_global.html index 45eeabe6..beb90e02 100644 --- a/doc/rsyslog_conf_global.html +++ b/doc/rsyslog_conf_global.html @@ -17,6 +17,8 @@ appear as implementation progresses. many parameter settings modify queue parameters. If in doubt, use the default, it is usually well-chosen and applicable in most cases.</p> <ul> +<li><a href="rsconf1_abortonuncleanconfig.html">$AbortOnUncleanConfig</a> - abort startup if there is +any issue with the config file</li> <li><a href="rsconf1_actionexeconlywhenpreviousissuspended.html">$ActionExecOnlyWhenPreviousIsSuspended</a></li> <li>$ActionName <a_single_word> - used primarily for documentation, e.g. when generating a configuration graph. Available sice 4.3.1. @@ -158,7 +160,12 @@ Usually that should not be a big issue, as the restart-type HUP can easily be re something along the lines of "/etc/init.d/rsyslog restart". </li> <li><a href="rsconf1_includeconfig.html">$IncludeConfig</a></li><li>MainMsgQueueCheckpointInterval <number></li> -<li>$MainMsgQueueDequeueBatchSize <number> [default 32]</li> +<li><b>$LogRSyslogStatusMessages</b> [<b>on</b>/off] - If set to on (the default), +rsyslog emits message on startup and shutdown as well as when it is HUPed. +This information might be needed by some log analyzers. If set to off, no such +status messages are logged, what may be useful for other scenarios. +[available since 4.7.0 and 5.3.0] +<li><b>$MainMsgQueueDequeueBatchSize</b> <number> [default 32]</li> <li>$MainMsgQueueDequeueSlowdown <number> [number is timeout in <i> micro</i>seconds (1000000us is 1sec!), default 0 (no delay). Simple rate-limiting!]</li> @@ -231,6 +238,7 @@ error recovery thus can handle write errors without data loss. Note that this op severely reduces the effect of zip compression and should be switched to off for that use case. Note that the default -off- is primarily an aid to preserve the traditional syslogd behaviour.</li> +<li><a href="rsconf1_omfileforcechown.html">$omfileForceChown</a> - force ownership change for all files</li> <li><b>$RepeatedMsgContainsOriginalMsg</b> [on/<b>off</b>] - "last message repeated n times" messages, if generated, have a different format that contains the message that is being repeated. Note that only the first "n" characters are included, with n to be at least 80 characters, most @@ -241,10 +249,14 @@ large enough for the whole message. (Introduced with 4.1.5). Once set, it affect <li><a href="rsconf1_resetconfigvariables.html">$ResetConfigVariables</a></li> <li><b>$Ruleset</b> <i>name</i> - starts a new ruleset or switches back to one already defined. All following actions belong to that new rule set. -the <i>name</i> does not yet exist, it is created. To swith back to rsyslog's +the <i>name</i> does not yet exist, it is created. To switch back to rsyslog's default ruleset, specify "RSYSLOG_DefaultRuleset") as the name. All following actions belong to that new rule set. It is advised to also read our paper on <a href="multi_ruleset.html">using multiple rule sets in rsyslog</a>.</li> +<li><b><a href="rsconf1_rulesetcreatemainqueue.html">$RulesetCreateMainQueue</a></b> on - creates +a ruleset-specific main queue. +<li><b><a href="rsconf1_rulesetparser.html">$RulesetParser</a></b> - enables to set +a specific (list of) message parsers to be used with the ruleset. <li><b>$OptimizeForUniprocessor</b> [on/<b>off</b>] - turns on optimizatons which lead to better performance on uniprocessors. If you run on multicore-machiens, turning this off lessens CPU load. The default may change as uniprocessor systems become less common. [available since 4.1.0]</li> @@ -252,19 +264,6 @@ default may change as uniprocessor systems become less common. [available since to sysklogd), the domain part from a name that is within the same domain as the receiving system is stripped. If set to on, full names are always used.</li> <li>$WorkDirectory <name> (directory for spool and other work files)</li> -<li>$UDPServerAddress <IP> (imudp) -- local IP -address (or name) the UDP listens should bind to</li> -<li>$UDPServerRun <port> (imudp) -- former --r<port> option, default 514, start UDP server on this -port, "*" means all addresses</li> -<li>$UDPServerTimeRequery <nbr-of-times> (imudp) -- this is a performance -optimization. Getting the system time is very costly. With this setting, imudp can -be instructed to obtain the precise time only once every n-times. This logic is -only activated if messages come in at a very fast rate, so doing less frequent -time calls should usually be acceptable. The default value is two, because we have -seen that even without optimization the kernel often returns twice the identical time. -You can set this value as high as you like, but do so at your own risk. The higher -the value, the less precise the timestamp. <li><a href="droppriv.html">$PrivDropToGroup</a></li> <li><a href="droppriv.html">$PrivDropToGroupID</a></li> <li><a href="droppriv.html">$PrivDropToUser</a></li> |