diff options
Diffstat (limited to 'doc/omudpspoof.html')
| -rw-r--r-- | doc/omudpspoof.html | 20 |
1 files changed, 10 insertions, 10 deletions
diff --git a/doc/omudpspoof.html b/doc/omudpspoof.html index 16cb9b13..df14bbe1 100644 --- a/doc/omudpspoof.html +++ b/doc/omudpspoof.html @@ -16,7 +16,7 @@ spoof the sender address. Also, it enables to circle through a number of source ports. <p><b>Configuration Directives</b>:</p> <ul> -<li><b>$ActionOMUDPSpoofSourceNameTemplate</b> <templatename><br> +<li><b>$ActionOMOMUDPSpoofSourceNameTemplate</b> <templatename><br> This is the name of the template that contains a numerical IP address that is to be used as the source system IP address. While it may often be a constant value, it can be generated as usual via the @@ -28,7 +28,7 @@ So in essence, the default template spoofs the address of the system the message was received from. This is considered the most important use case. <li><b>$ActionOMUDPSpoofTargetHost</b> <hostname><br> Host that the messages shall be sent to. -<li><b>$ActionUDPSpoofTargetPort</b> <port><br> +<li><b>$ActionOMUDPSpoofTargetPort</b> <port><br> Remote port that the messages shall be sent to. <li><b>$ActionOMUDPSpoofDefaultTemplate</b> <templatename><br> This setting instructs omudpspoof to use a template different from the @@ -53,7 +53,7 @@ care about the source port. This example is considered the typical use case for omudpspoof. </p> <textarea rows="5" cols="80">$ModLoad omudpspoof -$ActionUDPSpoofTargetHost server.example.com +$ActionOMUDPSpoofTargetHost server.example.com *.* :omudpspoof: </textarea> @@ -64,10 +64,10 @@ source port 514 is used. <textarea rows="8" cols="80">$ModLoad omudpspoof $template spoofaddr,"192.0.2.1" $template spooftemplate,"%rawmsg%" -$ActionUDPSpoofSourceNameTemplate spoofaddr -$ActionUDPSpoofTargetHost server.example.com -$ActionUDPSpoofSourcePortStart 514 -$ActionUDPSpoofSourcePortEnd 514 +$ActionOMUDPSpoofSourceNameTemplate spoofaddr +$ActionOMUDPSpoofTargetHost server.example.com +$ActionOMUDPSpoofSourcePortStart 514 +$ActionOMUDPSpoofSourcePortEnd 514 *.* :omudpspoof:;spooftemplate </textarea> <p>The following sample is similar to the previous, but uses as many defaults as possible. @@ -77,8 +77,8 @@ have been changed, the previously set defaults will be used! </p> <textarea rows="5" cols="80">$ModLoad omudpspoof $template spoofaddr,"192.0.2.1" -$ActionUDPSpoofSourceNameTemplate spoofaddr -$ActionUDPSpoofTargetHost server.example.com +$ActionOMUDPSpoofSourceNameTemplate spoofaddr +$ActionOMUDPSpoofTargetHost server.example.com *.* :omudpspoof: </textarea> <p>[<a href="rsyslog_conf.html">rsyslog.conf overview</a>] @@ -86,7 +86,7 @@ $ActionUDPSpoofTargetHost server.example.com <p><font size="2">This documentation is part of the <a href="http://www.rsyslog.com/">rsyslog</a> project.<br> -Copyright © 2009 by <a href="http://www.gerhards.net/rainer">Rainer Gerhards</a> and +Copyright © 2009-2012 by <a href="http://www.gerhards.net/rainer">Rainer Gerhards</a> and <a href="http://www.adiscon.com/">Adiscon</a>. Released under the GNU GPL version 3 or higher.</font></p> </body></html> |