From eb9069119d1c4bc856b4c1339abcad0105691e71 Mon Sep 17 00:00:00 2001 From: Haojian Zhuang Date: Wed, 15 Jul 2009 19:47:24 +0800 Subject: [ARM] pxa: fix gpio issue in zylonite WARNING: at drivers/gpio/gpiolib.c:83 gpio_ensure_requested+0x58/0xbc() autorequest GPIO-71 Modules linked in: [] (unwind_backtrace+0x0/0xe8) from [] (warn_slowpath_common+0x48/0x78) [] (warn_slowpath_common+0x48/0x78) from [] (warn_slowpath_fmt+0x28/0x38) [] (warn_slowpath_fmt+0x28/0x38) from [] (gpio_ensure_requested+0x58/0xbc) [] (gpio_ensure_requested+0x58/0xbc) from [] (gpio_direction_input+0x80/0xf4) [] (gpio_direction_input+0x80/0xf4) from [] (zylonite_pxa300_init+0x108/0x214) [] (zylonite_pxa300_init+0x108/0x214) from [] (zylonite_init+0x8/0x84) [] (zylonite_init+0x8/0x84) from [] (customize_machine+0x18/0x24) [] (customize_machine+0x18/0x24) from [] (do_one_initcall+0x30/0x1b0) [] (do_one_initcall+0x30/0x1b0) from [] (kernel_init+0xa4/0x11c) [] (kernel_init+0xa4/0x11c) from [] (kernel_thread_exit+0x0/0x8) ---[ end trace 1b75b31a2719ed1c ]--- This issue is caused by using gpio pin without request. Add gpio_request() into zylonite. To simplify the code, error checking is omitted since this is being performed early. Signed-off-by: Haojian Zhuang Signed-off-by: Eric Miao --- arch/arm/mach-pxa/zylonite_pxa300.c | 2 ++ arch/arm/mach-pxa/zylonite_pxa320.c | 2 ++ 2 files changed, 4 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-pxa/zylonite_pxa300.c b/arch/arm/mach-pxa/zylonite_pxa300.c index cefd1c0a854..84095440a87 100644 --- a/arch/arm/mach-pxa/zylonite_pxa300.c +++ b/arch/arm/mach-pxa/zylonite_pxa300.c @@ -197,10 +197,12 @@ static void __init zylonite_detect_lcd_panel(void) for (i = 0; i < NUM_LCD_DETECT_PINS; i++) { id = id << 1; gpio = mfp_to_gpio(lcd_detect_pins[i]); + gpio_request(gpio, "LCD_ID_PINS"); gpio_direction_input(gpio); if (gpio_get_value(gpio)) id = id | 0x1; + gpio_free(gpio); } /* lcd id, flush out bit 1 */ diff --git a/arch/arm/mach-pxa/zylonite_pxa320.c b/arch/arm/mach-pxa/zylonite_pxa320.c index cc5a2283360..60d08f23f5e 100644 --- a/arch/arm/mach-pxa/zylonite_pxa320.c +++ b/arch/arm/mach-pxa/zylonite_pxa320.c @@ -176,10 +176,12 @@ static void __init zylonite_detect_lcd_panel(void) for (i = 0; i < NUM_LCD_DETECT_PINS; i++) { id = id << 1; gpio = mfp_to_gpio(lcd_detect_pins[i]); + gpio_request(gpio, "LCD_ID_PINS"); gpio_direction_input(gpio); if (gpio_get_value(gpio)) id = id | 0x1; + gpio_free(gpio); } /* lcd id, flush out bit 1 */ -- cgit From ecf763c5677faee04d47333e6ed8e9539a427770 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Thu, 16 Jul 2009 19:37:29 +0200 Subject: [ARM] pxa: add STUART MFP config for PalmTX,T5,LD Signed-off-by: Marek Vasut Signed-off-by: Eric Miao --- arch/arm/mach-pxa/palmld.c | 4 ++++ arch/arm/mach-pxa/palmt5.c | 4 ++++ arch/arm/mach-pxa/palmtx.c | 4 ++++ 3 files changed, 12 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-pxa/palmld.c b/arch/arm/mach-pxa/palmld.c index ed70f281dd0..169fcc18154 100644 --- a/arch/arm/mach-pxa/palmld.c +++ b/arch/arm/mach-pxa/palmld.c @@ -128,6 +128,10 @@ static unsigned long palmld_pin_config[] __initdata = { GPIO38_GPIO, /* wifi ready */ GPIO81_GPIO, /* wifi reset */ + /* FFUART */ + GPIO34_FFUART_RXD, + GPIO39_FFUART_TXD, + /* HDD */ GPIO98_GPIO, /* HDD reset */ GPIO115_GPIO, /* HDD power */ diff --git a/arch/arm/mach-pxa/palmt5.c b/arch/arm/mach-pxa/palmt5.c index aae64a12a73..33f726ff55e 100644 --- a/arch/arm/mach-pxa/palmt5.c +++ b/arch/arm/mach-pxa/palmt5.c @@ -111,6 +111,10 @@ static unsigned long palmt5_pin_config[] __initdata = { /* PWM */ GPIO16_PWM0_OUT, + /* FFUART */ + GPIO34_FFUART_RXD, + GPIO39_FFUART_TXD, + /* MISC */ GPIO10_GPIO, /* hotsync button */ GPIO90_GPIO, /* power detect */ diff --git a/arch/arm/mach-pxa/palmtx.c b/arch/arm/mach-pxa/palmtx.c index 6c15d84bde5..83d02087958 100644 --- a/arch/arm/mach-pxa/palmtx.c +++ b/arch/arm/mach-pxa/palmtx.c @@ -127,6 +127,10 @@ static unsigned long palmtx_pin_config[] __initdata = { GPIO76_LCD_PCLK, GPIO77_LCD_BIAS, + /* FFUART */ + GPIO34_FFUART_RXD, + GPIO39_FFUART_TXD, + /* MISC. */ GPIO10_GPIO, /* hotsync button */ GPIO12_GPIO, /* power detect */ -- cgit From 1d3e216f1d303878d7204de94dee251bc2702175 Mon Sep 17 00:00:00 2001 From: Mike Rapoport Date: Tue, 21 Jul 2009 17:09:52 +0300 Subject: [ARM] pxa/em-x270: fix compile failure when CONFIG_APM_EMULATION=n If CONFIG_APM_EMULATION=n em-x270 build fails with linker error: arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_critical': em-x270.c:(.text+0x12c0): undefined reference to `apm_queue_event' arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_low': em-x270.c:(.text+0x12c8): undefined reference to `apm_queue_event' make: *** [.tmp_vmlinux1] Error 1 Fix it. Signed-off-by: Mike Rapoport Signed-off-by: Eric Miao --- arch/arm/mach-pxa/em-x270.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c index 63b10d9bb1d..9cd09465a0e 100644 --- a/arch/arm/mach-pxa/em-x270.c +++ b/arch/arm/mach-pxa/em-x270.c @@ -1141,12 +1141,16 @@ struct power_supply_info em_x270_psy_info = { static void em_x270_battery_low(void) { +#if defined(CONFIG_APM_EMULATION) apm_queue_event(APM_LOW_BATTERY); +#endif } static void em_x270_battery_critical(void) { +#if defined(CONFIG_APM_EMULATION) apm_queue_event(APM_CRITICAL_SUSPEND); +#endif } struct da9030_battery_info em_x270_batterty_info = { -- cgit From dc78baa2b90b289590911b40b6800f77d0dc935a Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Fri, 3 Jul 2009 19:24:33 +0200 Subject: dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on at91sam9rl chip. It will be used on other products in the future. This first release covers only the memory-to-memory tranfer type. This is the only tranfer type supported by this chip. On other products, it will be used also for peripheral DMA transfer (slave API support to come). I used dmatest client without problem in different configurations to test it. Full documentation for this controller can be found in the SAM9RL datasheet: http://www.atmel.com/dyn/products/product_card.asp?part_id=4243 Signed-off-by: Nicolas Ferre Acked-by: Maciej Sosnowski Signed-off-by: Dan Williams --- arch/arm/mach-at91/include/mach/at_hdmac.h | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+) create mode 100644 arch/arm/mach-at91/include/mach/at_hdmac.h (limited to 'arch/arm') diff --git a/arch/arm/mach-at91/include/mach/at_hdmac.h b/arch/arm/mach-at91/include/mach/at_hdmac.h new file mode 100644 index 00000000000..21a5554f9cb --- /dev/null +++ b/arch/arm/mach-at91/include/mach/at_hdmac.h @@ -0,0 +1,26 @@ +/* + * Header file for the Atmel AHB DMA Controller driver + * + * Copyright (C) 2008 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ +#ifndef AT_HDMAC_H +#define AT_HDMAC_H + +#include + +/** + * struct at_dma_platform_data - Controller configuration parameters + * @nr_channels: Number of channels supported by hardware (max 8) + * @cap_mask: dma_capability flags supported by the platform + */ +struct at_dma_platform_data { + unsigned int nr_channels; + dma_cap_mask_t cap_mask; +}; + +#endif /* AT_HDMAC_H */ -- cgit From 808347f6a31792079e345ec865e9cfcb6e8ae6b2 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Wed, 22 Jul 2009 20:04:45 +0200 Subject: dmaengine: at_hdmac: add DMA slave transfers This patch for at_hdmac adds the slave transfers capability to the Atmel DMA controller available on some AT91 SOCs. This allow peripheral to memory and memory to peripheral transfers with hardware handshaking. Slave structure for controller specific information is passed through channel private data. This at_dma_slave structure is defined in at_hdmac.h header file and relative hardware definition are moved to this file from at_hdmac_regs.h. Doing this we allow the channel configuration from platform definition code. This work is intensively based on dw_dmac and several slave implementations. Signed-off-by: Nicolas Ferre Signed-off-by: Dan Williams --- arch/arm/mach-at91/include/mach/at_hdmac.h | 76 ++++++++++++++++++++++++++++++ 1 file changed, 76 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-at91/include/mach/at_hdmac.h b/arch/arm/mach-at91/include/mach/at_hdmac.h index 21a5554f9cb..187cb58345c 100644 --- a/arch/arm/mach-at91/include/mach/at_hdmac.h +++ b/arch/arm/mach-at91/include/mach/at_hdmac.h @@ -23,4 +23,80 @@ struct at_dma_platform_data { dma_cap_mask_t cap_mask; }; +/** + * enum at_dma_slave_width - DMA slave register access width. + * @AT_DMA_SLAVE_WIDTH_8BIT: Do 8-bit slave register accesses + * @AT_DMA_SLAVE_WIDTH_16BIT: Do 16-bit slave register accesses + * @AT_DMA_SLAVE_WIDTH_32BIT: Do 32-bit slave register accesses + */ +enum at_dma_slave_width { + AT_DMA_SLAVE_WIDTH_8BIT = 0, + AT_DMA_SLAVE_WIDTH_16BIT, + AT_DMA_SLAVE_WIDTH_32BIT, +}; + +/** + * struct at_dma_slave - Controller-specific information about a slave + * @dma_dev: required DMA master device + * @tx_reg: physical address of data register used for + * memory-to-peripheral transfers + * @rx_reg: physical address of data register used for + * peripheral-to-memory transfers + * @reg_width: peripheral register width + * @cfg: Platform-specific initializer for the CFG register + * @ctrla: Platform-specific initializer for the CTRLA register + */ +struct at_dma_slave { + struct device *dma_dev; + dma_addr_t tx_reg; + dma_addr_t rx_reg; + enum at_dma_slave_width reg_width; + u32 cfg; + u32 ctrla; +}; + + +/* Platform-configurable bits in CFG */ +#define ATC_SRC_PER(h) (0xFU & (h)) /* Channel src rq associated with periph handshaking ifc h */ +#define ATC_DST_PER(h) ((0xFU & (h)) << 4) /* Channel dst rq associated with periph handshaking ifc h */ +#define ATC_SRC_REP (0x1 << 8) /* Source Replay Mod */ +#define ATC_SRC_H2SEL (0x1 << 9) /* Source Handshaking Mod */ +#define ATC_SRC_H2SEL_SW (0x0 << 9) +#define ATC_SRC_H2SEL_HW (0x1 << 9) +#define ATC_DST_REP (0x1 << 12) /* Destination Replay Mod */ +#define ATC_DST_H2SEL (0x1 << 13) /* Destination Handshaking Mod */ +#define ATC_DST_H2SEL_SW (0x0 << 13) +#define ATC_DST_H2SEL_HW (0x1 << 13) +#define ATC_SOD (0x1 << 16) /* Stop On Done */ +#define ATC_LOCK_IF (0x1 << 20) /* Interface Lock */ +#define ATC_LOCK_B (0x1 << 21) /* AHB Bus Lock */ +#define ATC_LOCK_IF_L (0x1 << 22) /* Master Interface Arbiter Lock */ +#define ATC_LOCK_IF_L_CHUNK (0x0 << 22) +#define ATC_LOCK_IF_L_BUFFER (0x1 << 22) +#define ATC_AHB_PROT_MASK (0x7 << 24) /* AHB Protection */ +#define ATC_FIFOCFG_MASK (0x3 << 28) /* FIFO Request Configuration */ +#define ATC_FIFOCFG_LARGESTBURST (0x0 << 28) +#define ATC_FIFOCFG_HALFFIFO (0x1 << 28) +#define ATC_FIFOCFG_ENOUGHSPACE (0x2 << 28) + +/* Platform-configurable bits in CTRLA */ +#define ATC_SCSIZE_MASK (0x7 << 16) /* Source Chunk Transfer Size */ +#define ATC_SCSIZE_1 (0x0 << 16) +#define ATC_SCSIZE_4 (0x1 << 16) +#define ATC_SCSIZE_8 (0x2 << 16) +#define ATC_SCSIZE_16 (0x3 << 16) +#define ATC_SCSIZE_32 (0x4 << 16) +#define ATC_SCSIZE_64 (0x5 << 16) +#define ATC_SCSIZE_128 (0x6 << 16) +#define ATC_SCSIZE_256 (0x7 << 16) +#define ATC_DCSIZE_MASK (0x7 << 20) /* Destination Chunk Transfer Size */ +#define ATC_DCSIZE_1 (0x0 << 20) +#define ATC_DCSIZE_4 (0x1 << 20) +#define ATC_DCSIZE_8 (0x2 << 20) +#define ATC_DCSIZE_16 (0x3 << 20) +#define ATC_DCSIZE_32 (0x4 << 20) +#define ATC_DCSIZE_64 (0x5 << 20) +#define ATC_DCSIZE_128 (0x6 << 20) +#define ATC_DCSIZE_256 (0x7 << 20) + #endif /* AT_HDMAC_H */ -- cgit From 3174c88af4b6b2e81cacfaa2bb90cc7abe36f1cc Mon Sep 17 00:00:00 2001 From: Hartley Sweeten Date: Mon, 20 Jul 2009 18:12:23 +0100 Subject: [ARM] 5611/1: ep93xx: update ts72xx nor flash support Update the NOR flash support for TS-7200. The TS-7200 models all have 16-bit NOR flash. Update the platform init to support this. Remove the private TS72XX_NOR_* defines and use the common ep93xx defines for the external chip select physical base address instead. Move the NOR flash registration into a static __init function. When the NAND flash support is updated this function will also be used to register the NAND flash for the TS-7250 and TS-7260. Tested-by: Matthieu Crapet Signed-off-by: H Hartley Sweeten Signed-off-by: Russell King --- arch/arm/mach-ep93xx/include/mach/ts72xx.h | 3 --- arch/arm/mach-ep93xx/ts72xx.c | 18 +++++++++++++----- 2 files changed, 13 insertions(+), 8 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-ep93xx/include/mach/ts72xx.h b/arch/arm/mach-ep93xx/include/mach/ts72xx.h index 34ddec081c4..411734422c1 100644 --- a/arch/arm/mach-ep93xx/include/mach/ts72xx.h +++ b/arch/arm/mach-ep93xx/include/mach/ts72xx.h @@ -41,9 +41,6 @@ #define TS72XX_OPTIONS2_TS9420_BOOT 0x02 -#define TS72XX_NOR_PHYS_BASE 0x60000000 -#define TS72XX_NOR2_PHYS_BASE 0x62000000 - #define TS72XX_NAND1_DATA_PHYS_BASE 0x60000000 #define TS72XX_NAND2_DATA_PHYS_BASE 0x70000000 #define TS72XX_NAND_DATA_VIRT_BASE 0xfebfc000 diff --git a/arch/arm/mach-ep93xx/ts72xx.c b/arch/arm/mach-ep93xx/ts72xx.c index 7ee024d3482..aaf1371412a 100644 --- a/arch/arm/mach-ep93xx/ts72xx.c +++ b/arch/arm/mach-ep93xx/ts72xx.c @@ -112,13 +112,16 @@ static void __init ts72xx_map_io(void) } } +/************************************************************************* + * NOR flash (TS-7200 only) + *************************************************************************/ static struct physmap_flash_data ts72xx_flash_data = { - .width = 1, + .width = 2, }; static struct resource ts72xx_flash_resource = { - .start = TS72XX_NOR_PHYS_BASE, - .end = TS72XX_NOR_PHYS_BASE + SZ_16M - 1, + .start = EP93XX_CS6_PHYS_BASE, + .end = EP93XX_CS6_PHYS_BASE + SZ_16M - 1, .flags = IORESOURCE_MEM, }; @@ -132,6 +135,12 @@ static struct platform_device ts72xx_flash = { .resource = &ts72xx_flash_resource, }; +static void __init ts72xx_register_flash(void) +{ + if (board_is_ts7200()) + platform_device_register(&ts72xx_flash); +} + static unsigned char ts72xx_rtc_readbyte(unsigned long addr) { __raw_writeb(addr, TS72XX_RTC_INDEX_VIRT_BASE); @@ -165,8 +174,7 @@ static struct ep93xx_eth_data ts72xx_eth_data = { static void __init ts72xx_init_machine(void) { ep93xx_init_devices(); - if (board_is_ts7200()) - platform_device_register(&ts72xx_flash); + ts72xx_register_flash(); platform_device_register(&ts72xx_rtc_device); ep93xx_register_eth(&ts72xx_eth_data, 1); -- cgit From 58cda884ecc87dcce18d463b0c8bd928dae63ad8 Mon Sep 17 00:00:00 2001 From: Jean Pihet Date: Fri, 24 Jul 2009 19:43:25 -0600 Subject: OMAP3 SDRC: add support for 2 SDRAM chip selects Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2 SDRAM parts connected to the SDRC. This patch adds the following: - add a new argument of type omap_sdrc_params struct* to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params - adapted the OMAP boards files to the new prototype of omap2_init_common_hw - add the SDRC 2nd CS registers offsets defines - adapt the sram sleep code to configure the SDRC for the 2nd CS Note: If the 2nd param to omap2_init_common_hw is NULL, then the parameters are not programmed into the SDRC CS1 registers Tested on 3430 SDP and Beagleboard rev C2 and B5, with suspend/resume and frequency changes (cpufreq). Signed-off-by: Jean Pihet Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/board-2430sdp.c | 2 +- arch/arm/mach-omap2/board-3430sdp.c | 2 +- arch/arm/mach-omap2/board-4430sdp.c | 2 +- arch/arm/mach-omap2/board-apollon.c | 2 +- arch/arm/mach-omap2/board-generic.c | 2 +- arch/arm/mach-omap2/board-h4.c | 2 +- arch/arm/mach-omap2/board-ldp.c | 2 +- arch/arm/mach-omap2/board-omap3beagle.c | 3 +- arch/arm/mach-omap2/board-omap3evm.c | 2 +- arch/arm/mach-omap2/board-omap3pandora.c | 3 +- arch/arm/mach-omap2/board-overo.c | 3 +- arch/arm/mach-omap2/board-rx51.c | 2 +- arch/arm/mach-omap2/board-zoom2.c | 2 +- arch/arm/mach-omap2/clock34xx.c | 37 +++++++-- arch/arm/mach-omap2/io.c | 5 +- arch/arm/mach-omap2/sdrc.c | 63 +++++++++----- arch/arm/mach-omap2/sram34xx.S | 137 ++++++++++++++++++++++++------- arch/arm/plat-omap/include/mach/io.h | 3 +- arch/arm/plat-omap/include/mach/sdrc.h | 11 ++- arch/arm/plat-omap/include/mach/sram.h | 23 +++--- arch/arm/plat-omap/sram.c | 30 ++++--- 21 files changed, 236 insertions(+), 102 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-2430sdp.c b/arch/arm/mach-omap2/board-2430sdp.c index 9c3fdcdf76c..8ec2a132904 100644 --- a/arch/arm/mach-omap2/board-2430sdp.c +++ b/arch/arm/mach-omap2/board-2430sdp.c @@ -141,7 +141,7 @@ static inline void board_smc91x_init(void) static void __init omap_2430sdp_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c index 496a90e4ea7..ac262cd7450 100644 --- a/arch/arm/mach-omap2/board-3430sdp.c +++ b/arch/arm/mach-omap2/board-3430sdp.c @@ -169,7 +169,7 @@ static struct platform_device *sdp3430_devices[] __initdata = { static void __init omap_3430sdp_init_irq(void) { - omap2_init_common_hw(hyb18m512160af6_sdrc_params); + omap2_init_common_hw(hyb18m512160af6_sdrc_params, NULL); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c index 57e477bd89c..b0c7402248f 100644 --- a/arch/arm/mach-omap2/board-4430sdp.c +++ b/arch/arm/mach-omap2/board-4430sdp.c @@ -59,7 +59,7 @@ static void __init gic_init_irq(void) static void __init omap_4430sdp_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); #ifdef CONFIG_OMAP_32K_TIMER omap2_gp_clockevent_set_gptimer(1); #endif diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c index 06dfba888b0..dcfc20d0389 100644 --- a/arch/arm/mach-omap2/board-apollon.c +++ b/arch/arm/mach-omap2/board-apollon.c @@ -250,7 +250,7 @@ out: static void __init omap_apollon_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); apollon_init_smc91x(); diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c index 3492162a65c..fd00aa03690 100644 --- a/arch/arm/mach-omap2/board-generic.c +++ b/arch/arm/mach-omap2/board-generic.c @@ -33,7 +33,7 @@ static void __init omap_generic_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); } diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c index e7d017cdc43..7b1d61d5bb2 100644 --- a/arch/arm/mach-omap2/board-h4.c +++ b/arch/arm/mach-omap2/board-h4.c @@ -270,7 +270,7 @@ static void __init h4_init_flash(void) static void __init omap_h4_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); h4_init_flash(); diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c index d8bc0a7dcb8..ea383f88cb1 100644 --- a/arch/arm/mach-omap2/board-ldp.c +++ b/arch/arm/mach-omap2/board-ldp.c @@ -270,7 +270,7 @@ static inline void __init ldp_init_smsc911x(void) static void __init omap_ldp_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); ldp_init_smsc911x(); diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 991ac9c3803..4abefd9566e 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -282,7 +282,8 @@ static int __init omap3_beagle_i2c_init(void) static void __init omap3_beagle_init_irq(void) { - omap2_init_common_hw(mt46h32m32lf6_sdrc_params); + omap2_init_common_hw(mt46h32m32lf6_sdrc_params, + mt46h32m32lf6_sdrc_params); omap_init_irq(); #ifdef CONFIG_OMAP_32K_TIMER omap2_gp_clockevent_set_gptimer(12); diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index d3cc145814d..217e5a2861d 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -279,7 +279,7 @@ struct spi_board_info omap3evm_spi_board_info[] = { static void __init omap3_evm_init_irq(void) { - omap2_init_common_hw(mt46h32m32lf6_sdrc_params); + omap2_init_common_hw(mt46h32m32lf6_sdrc_params, NULL); omap_init_irq(); omap_gpio_init(); omap3evm_init_smc911x(); diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c index e32aa23ce96..9b991ced382 100644 --- a/arch/arm/mach-omap2/board-omap3pandora.c +++ b/arch/arm/mach-omap2/board-omap3pandora.c @@ -310,7 +310,8 @@ static int __init omap3pandora_i2c_init(void) static void __init omap3pandora_init_irq(void) { - omap2_init_common_hw(mt46h32m32lf6_sdrc_params); + omap2_init_common_hw(mt46h32m32lf6_sdrc_params, + mt46h32m32lf6_sdrc_params); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index dff5528fbfb..44bc1c54cd0 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -360,7 +360,8 @@ static int __init overo_i2c_init(void) static void __init overo_init_irq(void) { - omap2_init_common_hw(mt46h32m32lf6_sdrc_params); + omap2_init_common_hw(mt46h32m32lf6_sdrc_params, + mt46h32m32lf6_sdrc_params); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c index 374ff63c3eb..591ae8a5805 100644 --- a/arch/arm/mach-omap2/board-rx51.c +++ b/arch/arm/mach-omap2/board-rx51.c @@ -61,7 +61,7 @@ static struct omap_board_config_kernel rx51_config[] = { static void __init rx51_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-zoom2.c b/arch/arm/mach-omap2/board-zoom2.c index bcc0f7632de..427b7b8b123 100644 --- a/arch/arm/mach-omap2/board-zoom2.c +++ b/arch/arm/mach-omap2/board-zoom2.c @@ -25,7 +25,7 @@ static void __init omap_zoom2_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c index 045da923e75..1c6480d3ad6 100644 --- a/arch/arm/mach-omap2/clock34xx.c +++ b/arch/arm/mach-omap2/clock34xx.c @@ -725,7 +725,9 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) u32 unlock_dll = 0; u32 c; unsigned long validrate, sdrcrate, mpurate; - struct omap_sdrc_params *sp; + struct omap_sdrc_params *sdrc_cs0; + struct omap_sdrc_params *sdrc_cs1; + int ret; if (!clk || !rate) return -EINVAL; @@ -743,8 +745,8 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) else sdrcrate >>= ((clk->rate / rate) >> 1); - sp = omap2_sdrc_get_params(sdrcrate); - if (!sp) + ret = omap2_sdrc_get_params(sdrcrate, &sdrc_cs0, &sdrc_cs1); + if (ret) return -EINVAL; if (sdrcrate < MIN_SDRC_DLL_LOCK_FREQ) { @@ -765,12 +767,29 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) pr_debug("clock: changing CORE DPLL rate from %lu to %lu\n", clk->rate, validrate); - pr_debug("clock: SDRC timing params used: %08x %08x %08x\n", - sp->rfr_ctrl, sp->actim_ctrla, sp->actim_ctrlb); - - omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla, - sp->actim_ctrlb, new_div, unlock_dll, c, - sp->mr, rate > clk->rate); + pr_debug("clock: SDRC CS0 timing params used:" + " RFR %08x CTRLA %08x CTRLB %08x MR %08x\n", + sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla, + sdrc_cs0->actim_ctrlb, sdrc_cs0->mr); + if (sdrc_cs1) + pr_debug("clock: SDRC CS1 timing params used: " + " RFR %08x CTRLA %08x CTRLB %08x MR %08x\n", + sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla, + sdrc_cs1->actim_ctrlb, sdrc_cs1->mr); + + if (sdrc_cs1) + omap3_configure_core_dpll( + new_div, unlock_dll, c, rate > clk->rate, + sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla, + sdrc_cs0->actim_ctrlb, sdrc_cs0->mr, + sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla, + sdrc_cs1->actim_ctrlb, sdrc_cs1->mr); + else + omap3_configure_core_dpll( + new_div, unlock_dll, c, rate > clk->rate, + sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla, + sdrc_cs0->actim_ctrlb, sdrc_cs0->mr, + 0, 0, 0, 0); return 0; } diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index 3a86b0f6603..e9b9bcb19b4 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -276,14 +276,15 @@ static int __init _omap2_init_reprogram_sdrc(void) return v; } -void __init omap2_init_common_hw(struct omap_sdrc_params *sp) +void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0, + struct omap_sdrc_params *sdrc_cs1) { omap2_mux_init(); #ifndef CONFIG_ARCH_OMAP4 /* FIXME: Remove this once the clkdev is ready */ pwrdm_init(powerdomains_omap); clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps); omap2_clk_init(); - omap2_sdrc_init(sp); + omap2_sdrc_init(sdrc_cs0, sdrc_cs1); _omap2_init_reprogram_sdrc(); #endif gpmc_init(); diff --git a/arch/arm/mach-omap2/sdrc.c b/arch/arm/mach-omap2/sdrc.c index 2045441e838..2e9e38db30e 100644 --- a/arch/arm/mach-omap2/sdrc.c +++ b/arch/arm/mach-omap2/sdrc.c @@ -32,7 +32,7 @@ #include #include "sdrc.h" -static struct omap_sdrc_params *sdrc_init_params; +static struct omap_sdrc_params *sdrc_init_params_cs0, *sdrc_init_params_cs1; void __iomem *omap2_sdrc_base; void __iomem *omap2_sms_base; @@ -45,33 +45,49 @@ void __iomem *omap2_sms_base; /** * omap2_sdrc_get_params - return SDRC register values for a given clock rate * @r: SDRC clock rate (in Hz) + * @sdrc_cs0: chip select 0 ram timings ** + * @sdrc_cs1: chip select 1 ram timings ** * * Return pre-calculated values for the SDRC_ACTIM_CTRLA, - * SDRC_ACTIM_CTRLB, SDRC_RFR_CTRL, and SDRC_MR registers, for a given - * SDRC clock rate 'r'. These parameters control various timing - * delays in the SDRAM controller that are expressed in terms of the - * number of SDRC clock cycles to wait; hence the clock rate - * dependency. Note that sdrc_init_params must be sorted rate - * descending. Also assumes that both chip-selects use the same - * timing parameters. Returns a struct omap_sdrc_params * upon - * success, or NULL upon failure. + * SDRC_ACTIM_CTRLB, SDRC_RFR_CTRL and SDRC_MR registers in sdrc_cs[01] + * structs,for a given SDRC clock rate 'r'. + * These parameters control various timing delays in the SDRAM controller + * that are expressed in terms of the number of SDRC clock cycles to + * wait; hence the clock rate dependency. + * + * Supports 2 different timing parameters for both chip selects. + * + * Note 1: the sdrc_init_params_cs[01] must be sorted rate descending. + * Note 2: If sdrc_init_params_cs_1 is not NULL it must be of same size + * as sdrc_init_params_cs_0. + * + * Fills in the struct omap_sdrc_params * for each chip select. + * Returns 0 upon success or -1 upon failure. */ -struct omap_sdrc_params *omap2_sdrc_get_params(unsigned long r) +int omap2_sdrc_get_params(unsigned long r, + struct omap_sdrc_params **sdrc_cs0, + struct omap_sdrc_params **sdrc_cs1) { - struct omap_sdrc_params *sp; + struct omap_sdrc_params *sp0, *sp1; - if (!sdrc_init_params) - return NULL; + if (!sdrc_init_params_cs0) + return -1; - sp = sdrc_init_params; + sp0 = sdrc_init_params_cs0; + sp1 = sdrc_init_params_cs1; - while (sp->rate && sp->rate != r) - sp++; + while (sp0->rate && sp0->rate != r) { + sp0++; + if (sdrc_init_params_cs1) + sp1++; + } - if (!sp->rate) - return NULL; + if (!sp0->rate) + return -1; - return sp; + *sdrc_cs0 = sp0; + *sdrc_cs1 = sp1; + return 0; } @@ -83,13 +99,15 @@ void __init omap2_set_globals_sdrc(struct omap_globals *omap2_globals) /** * omap2_sdrc_init - initialize SMS, SDRC devices on boot - * @sp: pointer to a null-terminated list of struct omap_sdrc_params + * @sdrc_cs[01]: pointers to a null-terminated list of struct omap_sdrc_params + * Support for 2 chip selects timings * * Turn on smart idle modes for SDRAM scheduler and controller. * Program a known-good configuration for the SDRC to deal with buggy * bootloaders. */ -void __init omap2_sdrc_init(struct omap_sdrc_params *sp) +void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0, + struct omap_sdrc_params *sdrc_cs1) { u32 l; @@ -103,7 +121,8 @@ void __init omap2_sdrc_init(struct omap_sdrc_params *sp) l |= (0x2 << 3); sdrc_write_reg(l, SDRC_SYSCONFIG); - sdrc_init_params = sp; + sdrc_init_params_cs0 = sdrc_cs0; + sdrc_init_params_cs1 = sdrc_cs1; /* XXX Enable SRFRONIDLEREQ here also? */ l = (1 << SDRC_POWER_EXTCLKDIS_SHIFT) | diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index f41f8d96ddb..3aef7448b2a 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -36,7 +36,7 @@ .text -/* r4 parameters */ +/* r1 parameters */ #define SDRC_NO_UNLOCK_DLL 0x0 #define SDRC_UNLOCK_DLL 0x1 @@ -71,40 +71,71 @@ /* * omap3_sram_configure_core_dpll - change DPLL3 M2 divider - * r0 = new SDRC_RFR_CTRL register contents - * r1 = new SDRC_ACTIM_CTRLA register contents - * r2 = new SDRC_ACTIM_CTRLB register contents - * r3 = new M2 divider setting (only 1 and 2 supported right now) - * r4 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for + * + * Params passed in registers: + * r0 = new M2 divider setting (only 1 and 2 supported right now) + * r1 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for * SDRC rates < 83MHz - * r5 = number of MPU cycles to wait for SDRC to stabilize after + * r2 = number of MPU cycles to wait for SDRC to stabilize after * reprogramming the SDRC when switching to a slower MPU speed - * r6 = new SDRC_MR_0 register value - * r7 = increasing SDRC rate? (1 = yes, 0 = no) + * r3 = increasing SDRC rate? (1 = yes, 0 = no) + * + * Params passed via the stack. The needed params will be copied in SRAM + * before use by the code in SRAM (SDRAM is not accessible during SDRC + * reconfiguration): + * new SDRC_RFR_CTRL_0 register contents + * new SDRC_ACTIM_CTRL_A_0 register contents + * new SDRC_ACTIM_CTRL_B_0 register contents + * new SDRC_MR_0 register value + * new SDRC_RFR_CTRL_1 register contents + * new SDRC_ACTIM_CTRL_A_1 register contents + * new SDRC_ACTIM_CTRL_B_1 register contents + * new SDRC_MR_1 register value * + * If the param SDRC_RFR_CTRL_1 is 0, the parameters + * are not programmed into the SDRC CS1 registers */ ENTRY(omap3_sram_configure_core_dpll) stmfd sp!, {r1-r12, lr} @ store regs to stack - ldr r4, [sp, #52] @ pull extra args off the stack - ldr r5, [sp, #56] @ load extra args from the stack - ldr r6, [sp, #60] @ load extra args from the stack - ldr r7, [sp, #64] @ load extra args from the stack + + @ pull the extra args off the stack + @ and store them in SRAM + ldr r4, [sp, #52] + str r4, omap_sdrc_rfr_ctrl_0_val + ldr r4, [sp, #56] + str r4, omap_sdrc_actim_ctrl_a_0_val + ldr r4, [sp, #60] + str r4, omap_sdrc_actim_ctrl_b_0_val + ldr r4, [sp, #64] + str r4, omap_sdrc_mr_0_val + ldr r4, [sp, #68] + str r4, omap_sdrc_rfr_ctrl_1_val + cmp r4, #0 @ if SDRC_RFR_CTRL_1 is 0, + beq skip_cs1_params @ do not use cs1 params + ldr r4, [sp, #72] + str r4, omap_sdrc_actim_ctrl_a_1_val + ldr r4, [sp, #76] + str r4, omap_sdrc_actim_ctrl_b_1_val + ldr r4, [sp, #80] + str r4, omap_sdrc_mr_1_val +skip_cs1_params: dsb @ flush buffered writes to interconnect - cmp r7, #1 @ if increasing SDRC clk rate, + + cmp r3, #1 @ if increasing SDRC clk rate, bleq configure_sdrc @ program the SDRC regs early (for RFR) - cmp r4, #SDRC_UNLOCK_DLL @ set the intended DLL state + cmp r1, #SDRC_UNLOCK_DLL @ set the intended DLL state bleq unlock_dll blne lock_dll bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC bl configure_core_dpll @ change the DPLL3 M2 divider bl enable_sdrc @ take SDRC out of idle - cmp r4, #SDRC_UNLOCK_DLL @ wait for DLL status to change + cmp r1, #SDRC_UNLOCK_DLL @ wait for DLL status to change bleq wait_dll_unlock blne wait_dll_lock - cmp r7, #1 @ if increasing SDRC clk rate, + cmp r3, #1 @ if increasing SDRC clk rate, beq return_to_sdram @ return to SDRAM code, otherwise, bl configure_sdrc @ reprogram SDRC regs now - mov r12, r5 + mov r12, r2 bl wait_clk_stable @ wait for SDRC to stabilize return_to_sdram: isb @ prevent speculative exec past here @@ -149,7 +180,7 @@ configure_core_dpll: ldr r12, [r11] ldr r10, core_m2_mask_val @ modify m2 for core dpll and r12, r12, r10 - orr r12, r12, r3, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT + orr r12, r12, r0, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT str r12, [r11] ldr r12, [r11] @ posted-write barrier for CM bx lr @@ -187,15 +218,34 @@ wait_dll_unlock: bne wait_dll_unlock bx lr configure_sdrc: - ldr r11, omap3_sdrc_rfr_ctrl - str r0, [r11] - ldr r11, omap3_sdrc_actim_ctrla - str r1, [r11] - ldr r11, omap3_sdrc_actim_ctrlb - str r2, [r11] + ldr r12, omap_sdrc_rfr_ctrl_0_val @ fetch value from SRAM + ldr r11, omap3_sdrc_rfr_ctrl_0 @ fetch addr from SRAM + str r12, [r11] @ store + ldr r12, omap_sdrc_actim_ctrl_a_0_val + ldr r11, omap3_sdrc_actim_ctrl_a_0 + str r12, [r11] + ldr r12, omap_sdrc_actim_ctrl_b_0_val + ldr r11, omap3_sdrc_actim_ctrl_b_0 + str r12, [r11] + ldr r12, omap_sdrc_mr_0_val ldr r11, omap3_sdrc_mr_0 - str r6, [r11] - ldr r6, [r11] @ posted-write barrier for SDRC + str r12, [r11] + ldr r12, omap_sdrc_rfr_ctrl_1_val + cmp r12, #0 @ if SDRC_RFR_CTRL_1 is 0, + beq skip_cs1_prog @ do not program cs1 params + ldr r11, omap3_sdrc_rfr_ctrl_1 + str r12, [r11] + ldr r12, omap_sdrc_actim_ctrl_a_1_val + ldr r11, omap3_sdrc_actim_ctrl_a_1 + str r12, [r11] + ldr r12, omap_sdrc_actim_ctrl_b_1_val + ldr r11, omap3_sdrc_actim_ctrl_b_1 + str r12, [r11] + ldr r12, omap_sdrc_mr_1_val + ldr r11, omap3_sdrc_mr_1 + str r12, [r11] +skip_cs1_prog: + ldr r12, [r11] @ posted-write barrier for SDRC bx lr omap3_sdrc_power: @@ -206,14 +256,40 @@ omap3_cm_idlest1_core: .word OMAP34XX_CM_REGADDR(CORE_MOD, CM_IDLEST) omap3_cm_iclken1_core: .word OMAP34XX_CM_REGADDR(CORE_MOD, CM_ICLKEN1) -omap3_sdrc_rfr_ctrl: + +omap3_sdrc_rfr_ctrl_0: .word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_0) -omap3_sdrc_actim_ctrla: +omap3_sdrc_rfr_ctrl_1: + .word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_1) +omap3_sdrc_actim_ctrl_a_0: .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_0) -omap3_sdrc_actim_ctrlb: +omap3_sdrc_actim_ctrl_a_1: + .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_1) +omap3_sdrc_actim_ctrl_b_0: .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_0) +omap3_sdrc_actim_ctrl_b_1: + .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_1) omap3_sdrc_mr_0: .word OMAP34XX_SDRC_REGADDR(SDRC_MR_0) +omap3_sdrc_mr_1: + .word OMAP34XX_SDRC_REGADDR(SDRC_MR_1) +omap_sdrc_rfr_ctrl_0_val: + .word 0xDEADBEEF +omap_sdrc_rfr_ctrl_1_val: + .word 0xDEADBEEF +omap_sdrc_actim_ctrl_a_0_val: + .word 0xDEADBEEF +omap_sdrc_actim_ctrl_a_1_val: + .word 0xDEADBEEF +omap_sdrc_actim_ctrl_b_0_val: + .word 0xDEADBEEF +omap_sdrc_actim_ctrl_b_1_val: + .word 0xDEADBEEF +omap_sdrc_mr_0_val: + .word 0xDEADBEEF +omap_sdrc_mr_1_val: + .word 0xDEADBEEF + omap3_sdrc_dlla_status: .word OMAP34XX_SDRC_REGADDR(SDRC_DLLA_STATUS) omap3_sdrc_dlla_ctrl: @@ -223,3 +299,4 @@ core_m2_mask_val: ENTRY(omap3_sram_configure_core_dpll_sz) .word . - omap3_sram_configure_core_dpll + diff --git a/arch/arm/plat-omap/include/mach/io.h b/arch/arm/plat-omap/include/mach/io.h index 73f483d56ca..21fb0efdda8 100644 --- a/arch/arm/plat-omap/include/mach/io.h +++ b/arch/arm/plat-omap/include/mach/io.h @@ -228,7 +228,8 @@ extern void omap1_map_common_io(void); extern void omap1_init_common_hw(void); extern void omap2_map_common_io(void); -extern void omap2_init_common_hw(struct omap_sdrc_params *sp); +extern void omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0, + struct omap_sdrc_params *sdrc_cs1); #define __arch_ioremap(p,s,t) omap_ioremap(p,s,t) #define __arch_iounmap(v) omap_iounmap(v) diff --git a/arch/arm/plat-omap/include/mach/sdrc.h b/arch/arm/plat-omap/include/mach/sdrc.h index adc73522491..0be18e4ff18 100644 --- a/arch/arm/plat-omap/include/mach/sdrc.h +++ b/arch/arm/plat-omap/include/mach/sdrc.h @@ -30,6 +30,10 @@ #define SDRC_ACTIM_CTRL_A_0 0x09c #define SDRC_ACTIM_CTRL_B_0 0x0a0 #define SDRC_RFR_CTRL_0 0x0a4 +#define SDRC_MR_1 0x0B4 +#define SDRC_ACTIM_CTRL_A_1 0x0C4 +#define SDRC_ACTIM_CTRL_B_1 0x0C8 +#define SDRC_RFR_CTRL_1 0x0D4 /* * These values represent the number of memory clock cycles between @@ -102,8 +106,11 @@ struct omap_sdrc_params { u32 mr; }; -void __init omap2_sdrc_init(struct omap_sdrc_params *sp); -struct omap_sdrc_params *omap2_sdrc_get_params(unsigned long r); +void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0, + struct omap_sdrc_params *sdrc_cs1); +int omap2_sdrc_get_params(unsigned long r, + struct omap_sdrc_params **sdrc_cs0, + struct omap_sdrc_params **sdrc_cs1); #ifdef CONFIG_ARCH_OMAP2 diff --git a/arch/arm/plat-omap/include/mach/sram.h b/arch/arm/plat-omap/include/mach/sram.h index 4d53cc59d7a..8974e3fc269 100644 --- a/arch/arm/plat-omap/include/mach/sram.h +++ b/arch/arm/plat-omap/include/mach/sram.h @@ -21,11 +21,12 @@ extern void omap2_sram_reprogram_sdrc(u32 perf_level, u32 dll_val, u32 mem_type); extern u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass); -extern u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, - u32 sdrc_actim_ctrla, - u32 sdrc_actim_ctrlb, u32 m2, - u32 unlock_dll, u32 f, u32 sdrc_mr, - u32 inc); +extern u32 omap3_configure_core_dpll( + u32 m2, u32 unlock_dll, u32 f, u32 inc, + u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0, + u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0, + u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1, + u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1); /* Do not use these */ extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl); @@ -59,12 +60,12 @@ extern void omap243x_sram_reprogram_sdrc(u32 perf_level, u32 dll_val, u32 mem_type); extern unsigned long omap243x_sram_reprogram_sdrc_sz; - -extern u32 omap3_sram_configure_core_dpll(u32 sdrc_rfr_ctrl, - u32 sdrc_actim_ctrla, - u32 sdrc_actim_ctrlb, u32 m2, - u32 unlock_dll, u32 f, u32 sdrc_mr, - u32 inc); +extern u32 omap3_sram_configure_core_dpll( + u32 m2, u32 unlock_dll, u32 f, u32 inc, + u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0, + u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0, + u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1, + u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1); extern unsigned long omap3_sram_configure_core_dpll_sz; #endif diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c index 4ea73804d21..4e781c99f0e 100644 --- a/arch/arm/plat-omap/sram.c +++ b/arch/arm/plat-omap/sram.c @@ -373,20 +373,26 @@ static inline int omap243x_sram_init(void) #ifdef CONFIG_ARCH_OMAP3 -static u32 (*_omap3_sram_configure_core_dpll)(u32 sdrc_rfr_ctrl, - u32 sdrc_actim_ctrla, - u32 sdrc_actim_ctrlb, - u32 m2, u32 unlock_dll, - u32 f, u32 sdrc_mr, u32 inc); -u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, - u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll, - u32 f, u32 sdrc_mr, u32 inc) +static u32 (*_omap3_sram_configure_core_dpll)( + u32 m2, u32 unlock_dll, u32 f, u32 inc, + u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0, + u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0, + u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1, + u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1); + +u32 omap3_configure_core_dpll(u32 m2, u32 unlock_dll, u32 f, u32 inc, + u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0, + u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0, + u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1, + u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1) { BUG_ON(!_omap3_sram_configure_core_dpll); - return _omap3_sram_configure_core_dpll(sdrc_rfr_ctrl, - sdrc_actim_ctrla, - sdrc_actim_ctrlb, m2, - unlock_dll, f, sdrc_mr, inc); + return _omap3_sram_configure_core_dpll( + m2, unlock_dll, f, inc, + sdrc_rfr_ctrl_0, sdrc_actim_ctrl_a_0, + sdrc_actim_ctrl_b_0, sdrc_mr_0, + sdrc_rfr_ctrl_1, sdrc_actim_ctrl_a_1, + sdrc_actim_ctrl_b_1, sdrc_mr_1); } /* REVISIT: Should this be same as omap34xx_sram_init() after off-idle? */ -- cgit From 9fb97412c3be5d0d1dd0e9d7c5268469e4c942aa Mon Sep 17 00:00:00 2001 From: Jean Pihet Date: Fri, 24 Jul 2009 19:43:25 -0600 Subject: OMAP3: Setup MUX settings for SDRC CKE signals This patches ensures the MUX settings are correct for the SDRC CKE signals to SDRAM. This allows the self-refresh to work when 2 chip-selects are in use. A warning is thrown away in case the initial muxing is incorrect, in order to track faulty or old-dated bootloaders. Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options must be enabled for the mux code to have effect. Signed-off-by: Jean Pihet Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/board-omap3beagle.c | 4 ++++ arch/arm/mach-omap2/board-omap3pandora.c | 5 +++++ arch/arm/mach-omap2/board-overo.c | 5 +++++ arch/arm/mach-omap2/board-rx51.c | 4 ++++ arch/arm/mach-omap2/mux.c | 6 ++++++ arch/arm/plat-omap/include/mach/mux.h | 4 ++++ 6 files changed, 28 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 4abefd9566e..e00ba128cec 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -409,6 +409,10 @@ static void __init omap3_beagle_init(void) usb_musb_init(); omap3beagle_flash_init(); + + /* Ensure SDRC pins are mux'd for self-refresh */ + omap_cfg_reg(H16_34XX_SDRC_CKE0); + omap_cfg_reg(H17_34XX_SDRC_CKE1); } static void __init omap3_beagle_map_io(void) diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c index 9b991ced382..864ee3d021f 100644 --- a/arch/arm/mach-omap2/board-omap3pandora.c +++ b/arch/arm/mach-omap2/board-omap3pandora.c @@ -40,6 +40,7 @@ #include #include #include +#include #include "sdram-micron-mt46h32m32lf-6.h" #include "mmc-twl4030.h" @@ -398,6 +399,10 @@ static void __init omap3pandora_init(void) omap3pandora_ads7846_init(); pandora_keys_gpio_init(); usb_musb_init(); + + /* Ensure SDRC pins are mux'd for self-refresh */ + omap_cfg_reg(H16_34XX_SDRC_CKE0); + omap_cfg_reg(H17_34XX_SDRC_CKE1); } static void __init omap3pandora_map_io(void) diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index 44bc1c54cd0..6b171b338ec 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -44,6 +44,7 @@ #include #include #include +#include #include #include "sdram-micron-mt46h32m32lf-6.h" @@ -396,6 +397,10 @@ static void __init overo_init(void) overo_ads7846_init(); overo_init_smsc911x(); + /* Ensure SDRC pins are mux'd for self-refresh */ + omap_cfg_reg(H16_34XX_SDRC_CKE0); + omap_cfg_reg(H17_34XX_SDRC_CKE1); + if ((gpio_request(OVERO_GPIO_W2W_NRESET, "OVERO_GPIO_W2W_NRESET") == 0) && (gpio_direction_output(OVERO_GPIO_W2W_NRESET, 1) == 0)) { diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c index 591ae8a5805..1c9e07fe826 100644 --- a/arch/arm/mach-omap2/board-rx51.c +++ b/arch/arm/mach-omap2/board-rx51.c @@ -75,6 +75,10 @@ static void __init rx51_init(void) omap_serial_init(); usb_musb_init(); rx51_peripherals_init(); + + /* Ensure SDRC pins are mux'd for self-refresh */ + omap_cfg_reg(H16_34XX_SDRC_CKE0); + omap_cfg_reg(H17_34XX_SDRC_CKE1); } static void __init rx51_map_io(void) diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c index 026c4fc883a..43d6b92b65f 100644 --- a/arch/arm/mach-omap2/mux.c +++ b/arch/arm/mach-omap2/mux.c @@ -486,6 +486,12 @@ MUX_CFG_34XX("H19_34XX_GPIO164_OUT", 0x19c, OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT) MUX_CFG_34XX("J25_34XX_GPIO170", 0x1c6, OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT) + +/* OMAP3 SDRC CKE signals to SDR/DDR ram chips */ +MUX_CFG_34XX("H16_34XX_SDRC_CKE0", 0x262, + OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT) +MUX_CFG_34XX("H17_34XX_SDRC_CKE1", 0x264, + OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT) }; #define OMAP34XX_PINS_SZ ARRAY_SIZE(omap34xx_pins) diff --git a/arch/arm/plat-omap/include/mach/mux.h b/arch/arm/plat-omap/include/mach/mux.h index 85a62170576..80281c458ba 100644 --- a/arch/arm/plat-omap/include/mach/mux.h +++ b/arch/arm/plat-omap/include/mach/mux.h @@ -853,6 +853,10 @@ enum omap34xx_index { AE5_34XX_GPIO143, H19_34XX_GPIO164_OUT, J25_34XX_GPIO170, + + /* OMAP3 SDRC CKE signals to SDR/DDR ram chips */ + H16_34XX_SDRC_CKE0, + H17_34XX_SDRC_CKE1, }; struct omap_mux_cfg { -- cgit From 75f251e3d0803b028f3474fdc75be0994c377ab5 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 24 Jul 2009 19:44:01 -0600 Subject: OMAP2/3 SDRC: don't set SDRC_POWER.PWDENA on boot Stop setting SDRC_POWER.PWDENA on boot. There is a nasty erratum (34xx erratum 1.150) that can cause memory corruption if PWDENA is enabled. Based originally on a patch from Samu P. Onkalo . Tested on BeagleBoard rev C2. Signed-off-by: Paul Walmsley Cc: Samu P. Onkalo --- arch/arm/mach-omap2/sdrc.c | 5 ++++- arch/arm/mach-omap2/sram34xx.S | 2 -- 2 files changed, 4 insertions(+), 3 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/sdrc.c b/arch/arm/mach-omap2/sdrc.c index 2e9e38db30e..9e3bd4fa781 100644 --- a/arch/arm/mach-omap2/sdrc.c +++ b/arch/arm/mach-omap2/sdrc.c @@ -125,8 +125,11 @@ void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0, sdrc_init_params_cs1 = sdrc_cs1; /* XXX Enable SRFRONIDLEREQ here also? */ + /* + * PWDENA should not be set due to 34xx erratum 1.150 - PWDENA + * can cause random memory corruption + */ l = (1 << SDRC_POWER_EXTCLKDIS_SHIFT) | - (1 << SDRC_POWER_PWDENA_SHIFT) | (1 << SDRC_POWER_PAGEPOLICY_SHIFT); sdrc_write_reg(l, SDRC_POWER); } diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index 3aef7448b2a..9c2d0465a83 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -58,7 +58,6 @@ /* SDRC_POWER bit settings */ #define SRFRONIDLEREQ_MASK 0x40 -#define PWDENA_MASK 0x4 /* CM_IDLEST1_CORE bit settings */ #define ST_SDRC_MASK 0x2 @@ -160,7 +159,6 @@ sdram_in_selfrefresh: ldr r12, [r11] @ read the contents of SDRC_POWER mov r9, r12 @ keep a copy of SDRC_POWER bits orr r12, r12, #SRFRONIDLEREQ_MASK @ enable self refresh on idle - bic r12, r12, #PWDENA_MASK @ clear PWDENA str r12, [r11] @ write back to SDRC_POWER register ldr r12, [r11] @ posted-write barrier for SDRC idle_sdrc: -- cgit From 8ff120e5303e27e03aba7b774e86fd43eaf90376 Mon Sep 17 00:00:00 2001 From: Rajendra Nayak Date: Fri, 24 Jul 2009 19:44:01 -0600 Subject: OMAP3 SDRC: Fix freeze when scaling CORE dpll to < 83Mhz This patch fixes a bug in the CORE dpll scaling sequence which was errouneously clearing some bits in the SDRC DLLA CTRL register and hence causing a freeze. The issue was observed only on platforms which scale CORE dpll to < 83Mhz and hence program the DLL in fixed delay mode. Issue reported by Limei Wang , with debugging assistance from Richard Woodruff and Girish Ghongdemath . Signed-off-by: Rajendra Nayak Cc: Limei Wang Cc: Richard Woodruff Cc: Girish Ghongdemath Signed-off-by: Paul Walmsley [paul@pwsan.com: updated patch description to include collaboration credits] --- arch/arm/mach-omap2/sram34xx.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index 9c2d0465a83..e6b112590d7 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -143,7 +143,7 @@ return_to_sdram: unlock_dll: ldr r11, omap3_sdrc_dlla_ctrl ldr r12, [r11] - and r12, r12, #FIXEDDELAY_MASK + bic r12, r12, #FIXEDDELAY_MASK orr r12, r12, #FIXEDDELAY_DEFAULT orr r12, r12, #DLLIDLE_MASK str r12, [r11] @ (no OCP barrier needed) -- cgit From df56556e571234cf26072cd58c01ac3520986b44 Mon Sep 17 00:00:00 2001 From: Rajendra Nayak Date: Fri, 24 Jul 2009 19:44:02 -0600 Subject: OMAP3 SDRC: Move the clk stabilization delay to the right place The clock stabilization delay post a M2 divider change is needed even before a SDRC interface clock re-enable and not only before jumping back to SDRAM. Signed-off-by: Rajendra Nayak Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/sram34xx.S | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index e6b112590d7..82aa4a3d160 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -127,6 +127,8 @@ skip_cs1_params: blne lock_dll bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC bl configure_core_dpll @ change the DPLL3 M2 divider + mov r12, r2 + bl wait_clk_stable @ wait for SDRC to stabilize bl enable_sdrc @ take SDRC out of idle cmp r1, #SDRC_UNLOCK_DLL @ wait for DLL status to change bleq wait_dll_unlock @@ -134,8 +136,6 @@ skip_cs1_params: cmp r3, #1 @ if increasing SDRC clk rate, beq return_to_sdram @ return to SDRAM code, otherwise, bl configure_sdrc @ reprogram SDRC regs now - mov r12, r2 - bl wait_clk_stable @ wait for SDRC to stabilize return_to_sdram: isb @ prevent speculative exec past here mov r0, #0 @ return value -- cgit From 72350b29a4c0debfc27c2edbeed9b4ff3f935dd4 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 24 Jul 2009 19:44:03 -0600 Subject: OMAP2/3 clock: split, rename omap2_wait_clock_ready() Some OMAP2/3 hardware modules have CM_IDLEST attributes that are not handled by the current omap2_wait_clock_ready() code. In preparation for patches that fix the unusual devices, rename the function omap2_wait_clock_ready() to omap2_wait_module_ready() and split it into three parts: 1. A clkops-specific companion clock return function (by default, omap2_clk_dflt_find_companion()) 2. A clkops-specific CM_IDLEST register address and bit shift return function (by default, omap2_clk_dflt_find_idlest()) 3. Code to wait for the CM to indicate that the module is ready (omap2_cm_wait_idlest()) Clocks can now specify their own custom find_companion() and find_idlest() functions; used in subsequent patches. Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/clock.c | 156 ++++++++++++++++---------------- arch/arm/mach-omap2/clock.h | 6 ++ arch/arm/mach-omap2/prcm.c | 43 +++++++++ arch/arm/plat-omap/include/mach/clock.h | 2 + arch/arm/plat-omap/include/mach/prcm.h | 1 + 5 files changed, 131 insertions(+), 77 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index b0665f161c0..456e2ad5f62 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -27,6 +27,7 @@ #include #include #include +#include #include #include @@ -38,8 +39,6 @@ #include "cm-regbits-24xx.h" #include "cm-regbits-34xx.h" -#define MAX_CLOCK_ENABLE_WAIT 100000 - /* DPLL rate rounding: minimum DPLL multiplier, divider values */ #define DPLL_MIN_MULTIPLIER 1 #define DPLL_MIN_DIVIDER 1 @@ -274,83 +273,97 @@ unsigned long omap2_fixed_divisor_recalc(struct clk *clk) } /** - * omap2_wait_clock_ready - wait for clock to enable - * @reg: physical address of clock IDLEST register - * @mask: value to mask against to determine if the clock is active - * @name: name of the clock (for printk) + * omap2_clk_dflt_find_companion - find companion clock to @clk + * @clk: struct clk * to find the companion clock of + * @other_reg: void __iomem ** to return the companion clock CM_*CLKEN va in + * @other_bit: u8 ** to return the companion clock bit shift in + * + * Note: We don't need special code here for INVERT_ENABLE for the + * time being since INVERT_ENABLE only applies to clocks enabled by + * CM_CLKEN_PLL * - * Returns 1 if the clock enabled in time, or 0 if it failed to enable - * in roughly MAX_CLOCK_ENABLE_WAIT microseconds. + * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes it's + * just a matter of XORing the bits. + * + * Some clocks don't have companion clocks. For example, modules with + * only an interface clock (such as MAILBOXES) don't have a companion + * clock. Right now, this code relies on the hardware exporting a bit + * in the correct companion register that indicates that the + * nonexistent 'companion clock' is active. Future patches will + * associate this type of code with per-module data structures to + * avoid this issue, and remove the casts. No return value. */ -int omap2_wait_clock_ready(void __iomem *reg, u32 mask, const char *name) +void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg, + u8 *other_bit) { - int i = 0; - int ena = 0; + u32 r; /* - * 24xx uses 0 to indicate not ready, and 1 to indicate ready. - * 34xx reverses this, just to keep us on our toes + * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes + * it's just a matter of XORing the bits. */ - if (cpu_mask & (RATE_IN_242X | RATE_IN_243X)) - ena = mask; - else if (cpu_mask & RATE_IN_343X) - ena = 0; - - /* Wait for lock */ - while (((__raw_readl(reg) & mask) != ena) && - (i++ < MAX_CLOCK_ENABLE_WAIT)) { - udelay(1); - } - - if (i <= MAX_CLOCK_ENABLE_WAIT) - pr_debug("Clock %s stable after %d loops\n", name, i); - else - printk(KERN_ERR "Clock %s didn't enable in %d tries\n", - name, MAX_CLOCK_ENABLE_WAIT); - - - return (i < MAX_CLOCK_ENABLE_WAIT) ? 1 : 0; -}; + r = ((__force u32)clk->enable_reg ^ (CM_FCLKEN ^ CM_ICLKEN)); + *other_reg = (__force void __iomem *)r; + *other_bit = clk->enable_bit; +} -/* - * Note: We don't need special code here for INVERT_ENABLE - * for the time being since INVERT_ENABLE only applies to clocks enabled by - * CM_CLKEN_PLL +/** + * omap2_clk_dflt_find_idlest - find CM_IDLEST reg va, bit shift for @clk + * @clk: struct clk * to find IDLEST info for + * @idlest_reg: void __iomem ** to return the CM_IDLEST va in + * @idlest_bit: u8 ** to return the CM_IDLEST bit shift in + * + * Return the CM_IDLEST register address and bit shift corresponding + * to the module that "owns" this clock. This default code assumes + * that the CM_IDLEST bit shift is the CM_*CLKEN bit shift, and that + * the IDLEST register address ID corresponds to the CM_*CLKEN + * register address ID (e.g., that CM_FCLKEN2 corresponds to + * CM_IDLEST2). This is not true for all modules. No return value. */ -static void omap2_clk_wait_ready(struct clk *clk) +void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg, + u8 *idlest_bit) { - void __iomem *reg, *other_reg, *st_reg; - u32 bit; + u32 r; - /* - * REVISIT: This code is pretty ugly. It would be nice to generalize - * it and pull it into struct clk itself somehow. - */ - reg = clk->enable_reg; + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + *idlest_bit = clk->enable_bit; +} - /* - * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes - * it's just a matter of XORing the bits. - */ - other_reg = (void __iomem *)((u32)reg ^ (CM_FCLKEN ^ CM_ICLKEN)); +/** + * omap2_module_wait_ready - wait for an OMAP module to leave IDLE + * @clk: struct clk * belonging to the module + * + * If the necessary clocks for the OMAP hardware IP block that + * corresponds to clock @clk are enabled, then wait for the module to + * indicate readiness (i.e., to leave IDLE). This code does not + * belong in the clock code and will be moved in the medium term to + * module-dependent code. No return value. + */ +static void omap2_module_wait_ready(struct clk *clk) +{ + void __iomem *companion_reg, *idlest_reg; + u8 other_bit, idlest_bit; + + /* Not all modules have multiple clocks that their IDLEST depends on */ + if (clk->ops->find_companion) { + clk->ops->find_companion(clk, &companion_reg, &other_bit); + if (!(__raw_readl(companion_reg) & (1 << other_bit))) + return; + } - /* Check if both functional and interface clocks - * are running. */ - bit = 1 << clk->enable_bit; - if (!(__raw_readl(other_reg) & bit)) - return; - st_reg = (void __iomem *)(((u32)other_reg & ~0xf0) | 0x20); /* CM_IDLEST* */ + clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit); - omap2_wait_clock_ready(st_reg, bit, clk->name); + omap2_cm_wait_idlest(idlest_reg, (1 << idlest_bit), clk->name); } -static int omap2_dflt_clk_enable(struct clk *clk) +int omap2_dflt_clk_enable(struct clk *clk) { u32 v; if (unlikely(clk->enable_reg == NULL)) { - printk(KERN_ERR "clock.c: Enable for %s without enable code\n", + pr_err("clock.c: Enable for %s without enable code\n", clk->name); return 0; /* REVISIT: -EINVAL */ } @@ -363,26 +376,13 @@ static int omap2_dflt_clk_enable(struct clk *clk) __raw_writel(v, clk->enable_reg); v = __raw_readl(clk->enable_reg); /* OCP barrier */ - return 0; -} + if (clk->ops->find_idlest) + omap2_module_wait_ready(clk); -static int omap2_dflt_clk_enable_wait(struct clk *clk) -{ - int ret; - - if (!clk->enable_reg) { - printk(KERN_ERR "clock.c: Enable for %s without enable code\n", - clk->name); - return 0; /* REVISIT: -EINVAL */ - } - - ret = omap2_dflt_clk_enable(clk); - if (ret == 0) - omap2_clk_wait_ready(clk); - return ret; + return 0; } -static void omap2_dflt_clk_disable(struct clk *clk) +void omap2_dflt_clk_disable(struct clk *clk) { u32 v; @@ -406,8 +406,10 @@ static void omap2_dflt_clk_disable(struct clk *clk) } const struct clkops clkops_omap2_dflt_wait = { - .enable = omap2_dflt_clk_enable_wait, + .enable = omap2_dflt_clk_enable, .disable = omap2_dflt_clk_disable, + .find_companion = omap2_clk_dflt_find_companion, + .find_idlest = omap2_clk_dflt_find_idlest, }; const struct clkops clkops_omap2_dflt = { diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index 2679ddfa642..9ae7540f8af 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -65,6 +65,12 @@ int omap2_clksel_set_rate(struct clk *clk, unsigned long rate); u32 omap2_get_dpll_rate(struct clk *clk); int omap2_wait_clock_ready(void __iomem *reg, u32 cval, const char *name); void omap2_clk_prepare_for_reboot(void); +int omap2_dflt_clk_enable(struct clk *clk); +void omap2_dflt_clk_disable(struct clk *clk); +void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg, + u8 *other_bit); +void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg, + u8 *idlest_bit); extern const struct clkops clkops_omap2_dflt_wait; extern const struct clkops clkops_omap2_dflt; diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c index f945156d558..ced555a4cd1 100644 --- a/arch/arm/mach-omap2/prcm.c +++ b/arch/arm/mach-omap2/prcm.c @@ -17,6 +17,7 @@ #include #include #include +#include #include #include @@ -28,6 +29,8 @@ static void __iomem *prm_base; static void __iomem *cm_base; +#define MAX_MODULE_ENABLE_WAIT 100000 + u32 omap_prcm_get_reset_sources(void) { /* XXX This presumably needs modification for 34XX */ @@ -120,6 +123,46 @@ u32 cm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx) } EXPORT_SYMBOL(cm_rmw_mod_reg_bits); +/** + * omap2_cm_wait_idlest - wait for IDLEST bit to indicate module readiness + * @reg: physical address of module IDLEST register + * @mask: value to mask against to determine if the module is active + * @name: name of the clock (for printk) + * + * Returns 1 if the module indicated readiness in time, or 0 if it + * failed to enable in roughly MAX_MODULE_ENABLE_WAIT microseconds. + */ +int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name) +{ + int i = 0; + int ena = 0; + + /* + * 24xx uses 0 to indicate not ready, and 1 to indicate ready. + * 34xx reverses this, just to keep us on our toes + */ + if (cpu_is_omap24xx()) + ena = mask; + else if (cpu_is_omap34xx()) + ena = 0; + else + BUG(); + + /* Wait for lock */ + while (((__raw_readl(reg) & mask) != ena) && + (i++ < MAX_MODULE_ENABLE_WAIT)) + udelay(1); + + if (i < MAX_MODULE_ENABLE_WAIT) + pr_debug("cm: Module associated with clock %s ready after %d " + "loops\n", name, i); + else + pr_err("cm: Module associated with clock %s didn't enable in " + "%d tries\n", name, MAX_MODULE_ENABLE_WAIT); + + return (i < MAX_MODULE_ENABLE_WAIT) ? 1 : 0; +}; + void __init omap2_set_globals_prcm(struct omap_globals *omap2_globals) { prm_base = omap2_globals->prm; diff --git a/arch/arm/plat-omap/include/mach/clock.h b/arch/arm/plat-omap/include/mach/clock.h index f9f65e1ba3f..4b8b0d65cbf 100644 --- a/arch/arm/plat-omap/include/mach/clock.h +++ b/arch/arm/plat-omap/include/mach/clock.h @@ -20,6 +20,8 @@ struct clockdomain; struct clkops { int (*enable)(struct clk *); void (*disable)(struct clk *); + void (*find_idlest)(struct clk *, void __iomem **, u8 *); + void (*find_companion)(struct clk *, void __iomem **, u8 *); }; #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) || \ diff --git a/arch/arm/plat-omap/include/mach/prcm.h b/arch/arm/plat-omap/include/mach/prcm.h index 24ac3c71591..cda2a70397b 100644 --- a/arch/arm/plat-omap/include/mach/prcm.h +++ b/arch/arm/plat-omap/include/mach/prcm.h @@ -25,6 +25,7 @@ u32 omap_prcm_get_reset_sources(void); void omap_prcm_arch_reset(char mode); +int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name); #endif -- cgit From 3dc2197579089c5b74c7fba666c8ccf1a449afb4 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 24 Jul 2009 19:44:04 -0600 Subject: OMAP2 clock: 2430 I2CHS uses non-standard CM_IDLEST register OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE [1]. Fix by implementing a custom clkops .find_idlest function to return the correct slave IDLEST register. ... 1. OMAP2430 Multimedia Device Package-on-Package (POP) Silicon Revision 2.1 (Rev. V) Technical Reference Manual, tables 4-99 and 4-105. Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/clock24xx.c | 37 +++++++++++++++++++++++++++++++++++-- arch/arm/mach-omap2/clock24xx.h | 4 ++-- 2 files changed, 37 insertions(+), 4 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/clock24xx.c b/arch/arm/mach-omap2/clock24xx.c index 44de0271fc2..bc5d3ac6661 100644 --- a/arch/arm/mach-omap2/clock24xx.c +++ b/arch/arm/mach-omap2/clock24xx.c @@ -30,6 +30,7 @@ #include #include +#include #include #include @@ -43,6 +44,18 @@ static const struct clkops clkops_oscck; static const struct clkops clkops_fixed; +static void omap2430_clk_i2chs_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit); + +/* 2430 I2CHS has non-standard IDLEST register */ +static const struct clkops clkops_omap2430_i2chs_wait = { + .enable = omap2_dflt_clk_enable, + .disable = omap2_dflt_clk_disable, + .find_idlest = omap2430_clk_i2chs_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + #include "clock24xx.h" struct omap_clk { @@ -239,6 +252,26 @@ static void __iomem *prcm_clksrc_ctrl; * Omap24xx specific clock functions *-------------------------------------------------------------------------*/ +/** + * omap2430_clk_i2chs_find_idlest - return CM_IDLEST info for 2430 I2CHS + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * + * OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the + * CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE. This custom function + * passes back the correct CM_IDLEST register address for I2CHS + * modules. No return value. + */ +static void omap2430_clk_i2chs_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit) +{ + *idlest_reg = OMAP_CM_REGADDR(CORE_MOD, CM_IDLEST); + *idlest_bit = clk->enable_bit; +} + + /** * omap2xxx_clk_get_core_rate - return the CORE_CLK rate * @clk: pointer to the combined dpll_ck + core_ck (currently "dpll_ck") @@ -325,8 +358,8 @@ static int omap2_clk_fixed_enable(struct clk *clk) else if (clk == &apll54_ck) cval = OMAP24XX_ST_54M_APLL; - omap2_wait_clock_ready(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), cval, - clk->name); + omap2_cm_wait_idlest(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), cval, + clk->name); /* * REVISIT: Should we return an error code if omap2_wait_clock_ready() diff --git a/arch/arm/mach-omap2/clock24xx.h b/arch/arm/mach-omap2/clock24xx.h index 458f00cdcbe..d19cf7a7d8d 100644 --- a/arch/arm/mach-omap2/clock24xx.h +++ b/arch/arm/mach-omap2/clock24xx.h @@ -2337,7 +2337,7 @@ static struct clk i2c2_fck = { static struct clk i2chs2_fck = { .name = "i2c_fck", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap2430_i2chs_wait, .id = 2, .parent = &func_96m_ck, .clkdm_name = "core_l4_clkdm", @@ -2370,7 +2370,7 @@ static struct clk i2c1_fck = { static struct clk i2chs1_fck = { .name = "i2c_fck", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap2430_i2chs_wait, .id = 1, .parent = &func_96m_ck, .clkdm_name = "core_l4_clkdm", -- cgit From 3c82e229f09a6acc8d24dc27c5e0e60b1d7161c2 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 24 Jul 2009 19:44:06 -0600 Subject: OMAP3 clock: correct module IDLEST bits: SSI; DSS; USBHOST; HSOTGUSB Fix two bugs in the OMAP3 clock tree pertaining to the SSI, DSS, USBHOST, and HSOTGUSB devices. These devices are both interconnect initiators and targets. Without this patch, clk_enable()s on clocks for these modules can be very high latency (potentially up to ~200 milliseconds) and message such as the following are generated: Clock usbhost_48m_fck didn't enable in 100000 tries Two bugs are fixed by this patch. First, OMAP hardware only supports target CM_IDLEST register bits on ES2+ chips and beyond. ES1 chips should not wait for these clocks to enable. So, split the appropriate clocks into ES1 and ES2+ variants, so that kernels running on ES1 devices won't try to wait. Second, the current heuristic in omap2_clk_dflt_find_idlest() will fail for these clocks. It assumes that the CM_IDLEST bit to wait upon is the same as the CM_*CLKEN bit, which is false[1]. Fix by implementing custom clkops .find_idlest function pointers for the appropriate clocks that return the correct slave IDLEST bit shift. This was originally fixed in the linux-omap kernel during 2.6.29 in a slightly different manner[2][3]. In the medium-term future, all of the module IDLEST code will eventually be moved to the omap_hwmod code. Problem reported by Jarkko Nikula : http://marc.info/?l=linux-omap&m=124306184903679&w=2 ... 1. See for example 34xx TRM Revision P Table 4-213 and 4-217 (for the DSS case). 2. http://www.spinics.net/lists/linux-omap/msg05512.html et seq. 3. http://lkml.indiana.edu/hypermail/linux/kernel/0901.3/01498.html Signed-off-by: Paul Walmsley Cc: Jarkko Nikula --- arch/arm/mach-omap2/clock34xx.c | 118 +++++++++++++++++++++++++++++++++++++--- arch/arm/mach-omap2/clock34xx.h | 85 +++++++++++++++++++++++++---- 2 files changed, 185 insertions(+), 18 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c index 1c6480d3ad6..cd7819cc0c9 100644 --- a/arch/arm/mach-omap2/clock34xx.c +++ b/arch/arm/mach-omap2/clock34xx.c @@ -2,7 +2,7 @@ * OMAP3-specific clock framework functions * * Copyright (C) 2007-2008 Texas Instruments, Inc. - * Copyright (C) 2007-2008 Nokia Corporation + * Copyright (C) 2007-2009 Nokia Corporation * * Written by Paul Walmsley * Testing and integration fixes by Jouni Högander @@ -41,6 +41,37 @@ static const struct clkops clkops_noncore_dpll_ops; +static void omap3430es2_clk_ssi_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit); +static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit); +static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit); + +static const struct clkops clkops_omap3430es2_ssi_wait = { + .enable = omap2_dflt_clk_enable, + .disable = omap2_dflt_clk_disable, + .find_idlest = omap3430es2_clk_ssi_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + +static const struct clkops clkops_omap3430es2_hsotgusb_wait = { + .enable = omap2_dflt_clk_enable, + .disable = omap2_dflt_clk_disable, + .find_idlest = omap3430es2_clk_hsotgusb_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + +static const struct clkops clkops_omap3430es2_dss_usbhost_wait = { + .enable = omap2_dflt_clk_enable, + .disable = omap2_dflt_clk_disable, + .find_idlest = omap3430es2_clk_dss_usbhost_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + #include "clock34xx.h" struct omap_clk { @@ -157,10 +188,13 @@ static struct omap_clk omap34xx_clks[] = { CLK(NULL, "fshostusb_fck", &fshostusb_fck, CK_3430ES1), CLK(NULL, "core_12m_fck", &core_12m_fck, CK_343X), CLK("omap_hdq.0", "fck", &hdq_fck, CK_343X), - CLK(NULL, "ssi_ssr_fck", &ssi_ssr_fck, CK_343X), - CLK(NULL, "ssi_sst_fck", &ssi_sst_fck, CK_343X), + CLK(NULL, "ssi_ssr_fck", &ssi_ssr_fck_3430es1, CK_3430ES1), + CLK(NULL, "ssi_ssr_fck", &ssi_ssr_fck_3430es2, CK_3430ES2), + CLK(NULL, "ssi_sst_fck", &ssi_sst_fck_3430es1, CK_3430ES1), + CLK(NULL, "ssi_sst_fck", &ssi_sst_fck_3430es2, CK_3430ES2), CLK(NULL, "core_l3_ick", &core_l3_ick, CK_343X), - CLK("musb_hdrc", "ick", &hsotgusb_ick, CK_343X), + CLK("musb_hdrc", "ick", &hsotgusb_ick_3430es1, CK_3430ES1), + CLK("musb_hdrc", "ick", &hsotgusb_ick_3430es2, CK_3430ES2), CLK(NULL, "sdrc_ick", &sdrc_ick, CK_343X), CLK(NULL, "gpmc_fck", &gpmc_fck, CK_343X), CLK(NULL, "security_l3_ick", &security_l3_ick, CK_343X), @@ -193,18 +227,21 @@ static struct omap_clk omap34xx_clks[] = { CLK(NULL, "mailboxes_ick", &mailboxes_ick, CK_343X), CLK(NULL, "omapctrl_ick", &omapctrl_ick, CK_343X), CLK(NULL, "ssi_l4_ick", &ssi_l4_ick, CK_343X), - CLK(NULL, "ssi_ick", &ssi_ick, CK_343X), + CLK(NULL, "ssi_ick", &ssi_ick_3430es1, CK_3430ES1), + CLK(NULL, "ssi_ick", &ssi_ick_3430es2, CK_3430ES2), CLK(NULL, "usb_l4_ick", &usb_l4_ick, CK_3430ES1), CLK(NULL, "security_l4_ick2", &security_l4_ick2, CK_343X), CLK(NULL, "aes1_ick", &aes1_ick, CK_343X), CLK("omap_rng", "ick", &rng_ick, CK_343X), CLK(NULL, "sha11_ick", &sha11_ick, CK_343X), CLK(NULL, "des1_ick", &des1_ick, CK_343X), - CLK("omapfb", "dss1_fck", &dss1_alwon_fck, CK_343X), + CLK("omapfb", "dss1_fck", &dss1_alwon_fck_3430es1, CK_3430ES1), + CLK("omapfb", "dss1_fck", &dss1_alwon_fck_3430es2, CK_3430ES2), CLK("omapfb", "tv_fck", &dss_tv_fck, CK_343X), CLK("omapfb", "video_fck", &dss_96m_fck, CK_343X), CLK("omapfb", "dss2_fck", &dss2_alwon_fck, CK_343X), - CLK("omapfb", "ick", &dss_ick, CK_343X), + CLK("omapfb", "ick", &dss_ick_3430es1, CK_3430ES1), + CLK("omapfb", "ick", &dss_ick_3430es2, CK_3430ES2), CLK(NULL, "cam_mclk", &cam_mclk, CK_343X), CLK(NULL, "cam_ick", &cam_ick, CK_343X), CLK(NULL, "csi2_96m_fck", &csi2_96m_fck, CK_343X), @@ -300,6 +337,73 @@ static struct omap_clk omap34xx_clks[] = { */ #define SDRC_MPURATE_LOOPS 96 +/** + * omap3430es2_clk_ssi_find_idlest - return CM_IDLEST info for SSI + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * + * The OMAP3430ES2 SSI target CM_IDLEST bit is at a different shift + * from the CM_{I,F}CLKEN bit. Pass back the correct info via + * @idlest_reg and @idlest_bit. No return value. + */ +static void omap3430es2_clk_ssi_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit) +{ + u32 r; + + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + *idlest_bit = OMAP3430ES2_ST_SSI_IDLE_SHIFT; +} + +/** + * omap3430es2_clk_dss_usbhost_find_idlest - CM_IDLEST info for DSS, USBHOST + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * + * Some OMAP modules on OMAP3 ES2+ chips have both initiator and + * target IDLEST bits. For our purposes, we are concerned with the + * target IDLEST bits, which exist at a different bit position than + * the *CLKEN bit position for these modules (DSS and USBHOST) (The + * default find_idlest code assumes that they are at the same + * position.) No return value. + */ +static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit) +{ + u32 r; + + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + /* USBHOST_IDLE has same shift */ + *idlest_bit = OMAP3430ES2_ST_DSS_IDLE_SHIFT; +} + +/** + * omap3430es2_clk_hsotgusb_find_idlest - return CM_IDLEST info for HSOTGUSB + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * + * The OMAP3430ES2 HSOTGUSB target CM_IDLEST bit is at a different + * shift from the CM_{I,F}CLKEN bit. Pass back the correct info via + * @idlest_reg and @idlest_bit. No return value. + */ +static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit) +{ + u32 r; + + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + *idlest_bit = OMAP3430ES2_ST_HSOTGUSB_IDLE_SHIFT; +} + /** * omap3_dpll_recalc - recalculate DPLL rate * @clk: DPLL struct clk diff --git a/arch/arm/mach-omap2/clock34xx.h b/arch/arm/mach-omap2/clock34xx.h index e433aec4efd..57cc2725b92 100644 --- a/arch/arm/mach-omap2/clock34xx.h +++ b/arch/arm/mach-omap2/clock34xx.h @@ -1568,7 +1568,7 @@ static const struct clksel ssi_ssr_clksel[] = { { .parent = NULL } }; -static struct clk ssi_ssr_fck = { +static struct clk ssi_ssr_fck_3430es1 = { .name = "ssi_ssr_fck", .ops = &clkops_omap2_dflt, .init = &omap2_init_clksel_parent, @@ -1581,10 +1581,31 @@ static struct clk ssi_ssr_fck = { .recalc = &omap2_clksel_recalc, }; -static struct clk ssi_sst_fck = { +static struct clk ssi_ssr_fck_3430es2 = { + .name = "ssi_ssr_fck", + .ops = &clkops_omap3430es2_ssi_wait, + .init = &omap2_init_clksel_parent, + .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1), + .enable_bit = OMAP3430_EN_SSI_SHIFT, + .clksel_reg = OMAP_CM_REGADDR(CORE_MOD, CM_CLKSEL), + .clksel_mask = OMAP3430_CLKSEL_SSI_MASK, + .clksel = ssi_ssr_clksel, + .clkdm_name = "core_l4_clkdm", + .recalc = &omap2_clksel_recalc, +}; + +static struct clk ssi_sst_fck_3430es1 = { .name = "ssi_sst_fck", .ops = &clkops_null, - .parent = &ssi_ssr_fck, + .parent = &ssi_ssr_fck_3430es1, + .fixed_div = 2, + .recalc = &omap2_fixed_divisor_recalc, +}; + +static struct clk ssi_sst_fck_3430es2 = { + .name = "ssi_sst_fck", + .ops = &clkops_null, + .parent = &ssi_ssr_fck_3430es2, .fixed_div = 2, .recalc = &omap2_fixed_divisor_recalc, }; @@ -1606,9 +1627,19 @@ static struct clk core_l3_ick = { .recalc = &followparent_recalc, }; -static struct clk hsotgusb_ick = { +static struct clk hsotgusb_ick_3430es1 = { .name = "hsotgusb_ick", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap2_dflt, + .parent = &core_l3_ick, + .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), + .enable_bit = OMAP3430_EN_HSOTGUSB_SHIFT, + .clkdm_name = "core_l3_clkdm", + .recalc = &followparent_recalc, +}; + +static struct clk hsotgusb_ick_3430es2 = { + .name = "hsotgusb_ick", + .ops = &clkops_omap3430es2_hsotgusb_wait, .parent = &core_l3_ick, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), .enable_bit = OMAP3430_EN_HSOTGUSB_SHIFT, @@ -1947,7 +1978,7 @@ static struct clk ssi_l4_ick = { .recalc = &followparent_recalc, }; -static struct clk ssi_ick = { +static struct clk ssi_ick_3430es1 = { .name = "ssi_ick", .ops = &clkops_omap2_dflt, .parent = &ssi_l4_ick, @@ -1957,6 +1988,16 @@ static struct clk ssi_ick = { .recalc = &followparent_recalc, }; +static struct clk ssi_ick_3430es2 = { + .name = "ssi_ick", + .ops = &clkops_omap3430es2_ssi_wait, + .parent = &ssi_l4_ick, + .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), + .enable_bit = OMAP3430_EN_SSI_SHIFT, + .clkdm_name = "core_l4_clkdm", + .recalc = &followparent_recalc, +}; + /* REVISIT: Technically the TRM claims that this is CORE_CLK based, * but l4_ick makes more sense to me */ @@ -2024,7 +2065,7 @@ static struct clk des1_ick = { }; /* DSS */ -static struct clk dss1_alwon_fck = { +static struct clk dss1_alwon_fck_3430es1 = { .name = "dss1_alwon_fck", .ops = &clkops_omap2_dflt, .parent = &dpll4_m4x2_ck, @@ -2034,6 +2075,16 @@ static struct clk dss1_alwon_fck = { .recalc = &followparent_recalc, }; +static struct clk dss1_alwon_fck_3430es2 = { + .name = "dss1_alwon_fck", + .ops = &clkops_omap3430es2_dss_usbhost_wait, + .parent = &dpll4_m4x2_ck, + .enable_reg = OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_FCLKEN), + .enable_bit = OMAP3430_EN_DSS1_SHIFT, + .clkdm_name = "dss_clkdm", + .recalc = &followparent_recalc, +}; + static struct clk dss_tv_fck = { .name = "dss_tv_fck", .ops = &clkops_omap2_dflt, @@ -2067,7 +2118,7 @@ static struct clk dss2_alwon_fck = { .recalc = &followparent_recalc, }; -static struct clk dss_ick = { +static struct clk dss_ick_3430es1 = { /* Handles both L3 and L4 clocks */ .name = "dss_ick", .ops = &clkops_omap2_dflt, @@ -2079,6 +2130,18 @@ static struct clk dss_ick = { .recalc = &followparent_recalc, }; +static struct clk dss_ick_3430es2 = { + /* Handles both L3 and L4 clocks */ + .name = "dss_ick", + .ops = &clkops_omap3430es2_dss_usbhost_wait, + .parent = &l4_ick, + .init = &omap2_init_clk_clkdm, + .enable_reg = OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_ICLKEN), + .enable_bit = OMAP3430_CM_ICLKEN_DSS_EN_DSS_SHIFT, + .clkdm_name = "dss_clkdm", + .recalc = &followparent_recalc, +}; + /* CAM */ static struct clk cam_mclk = { @@ -2118,7 +2181,7 @@ static struct clk csi2_96m_fck = { static struct clk usbhost_120m_fck = { .name = "usbhost_120m_fck", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap2_dflt, .parent = &dpll5_m2_ck, .init = &omap2_init_clk_clkdm, .enable_reg = OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_FCLKEN), @@ -2129,7 +2192,7 @@ static struct clk usbhost_120m_fck = { static struct clk usbhost_48m_fck = { .name = "usbhost_48m_fck", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap3430es2_dss_usbhost_wait, .parent = &omap_48m_fck, .init = &omap2_init_clk_clkdm, .enable_reg = OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_FCLKEN), @@ -2141,7 +2204,7 @@ static struct clk usbhost_48m_fck = { static struct clk usbhost_ick = { /* Handles both L3 and L4 clocks */ .name = "usbhost_ick", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap3430es2_dss_usbhost_wait, .parent = &l4_ick, .init = &omap2_init_clk_clkdm, .enable_reg = OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_ICLKEN), -- cgit From 81566a060bb8f989cc369ea28837b05bd4adcedb Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:00:15 +0530 Subject: ARM: includecheck fix: misc.c fix the following 'make includecheck' warning: arch/arm/boot/compressed/misc.c: linux/compiler.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Signed-off-by: Russell King --- arch/arm/boot/compressed/misc.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/boot/compressed/misc.c b/arch/arm/boot/compressed/misc.c index 9e6e512f011..17153b54613 100644 --- a/arch/arm/boot/compressed/misc.c +++ b/arch/arm/boot/compressed/misc.c @@ -29,7 +29,6 @@ unsigned int __machine_arch_type; static void putstr(const char *ptr); -#include #include #ifdef CONFIG_DEBUG_ICEDCC -- cgit From feecaf73bb437cf72a44bd71598c6532d357f78e Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:01:39 +0530 Subject: ARM: includecheck fix: atomic.h fix the following 'make includecheck' warning: arch/arm/include/asm/atomic.h: asm/system.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Signed-off-by: Russell King --- arch/arm/include/asm/atomic.h | 2 -- 1 file changed, 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/include/asm/atomic.h b/arch/arm/include/asm/atomic.h index 9e07fe50702..9ed2377fe8e 100644 --- a/arch/arm/include/asm/atomic.h +++ b/arch/arm/include/asm/atomic.h @@ -159,8 +159,6 @@ static inline void atomic_clear_mask(unsigned long mask, unsigned long *addr) #else /* ARM_ARCH_6 */ -#include - #ifdef CONFIG_SMP #error SMP not supported on pre-ARMv6 CPUs #endif -- cgit From 44e96d452173ed22a7ba2291c7d566bf4b406f62 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:03:08 +0530 Subject: ARM: includecheck fix: board-dm355-evm.c fix the following 'make includecheck' warning: arch/arm/mach-davinci/board-dm355-evm.c: mach/common.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Kevin Hilman Signed-off-by: Russell King --- arch/arm/mach-davinci/board-dm355-evm.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-davinci/board-dm355-evm.c b/arch/arm/mach-davinci/board-dm355-evm.c index 5ac2f565d86..d6ab64ccd49 100644 --- a/arch/arm/mach-davinci/board-dm355-evm.c +++ b/arch/arm/mach-davinci/board-dm355-evm.c @@ -37,7 +37,6 @@ #include #include #include -#include #define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x01e10000 #define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x02000000 -- cgit From 7f25b0ac2dde2de399d6cfe42d9ec7066e665f2f Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:04:33 +0530 Subject: ARM: includecheck fix: board-dm355-leopard.c fix the following 'make includecheck' warning: arch/arm/mach-davinci/board-dm355-leopard.c: mach/common.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Kevin Hilman Signed-off-by: Russell King --- arch/arm/mach-davinci/board-dm355-leopard.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-davinci/board-dm355-leopard.c b/arch/arm/mach-davinci/board-dm355-leopard.c index 28c9008df4f..84ad5d161a8 100644 --- a/arch/arm/mach-davinci/board-dm355-leopard.c +++ b/arch/arm/mach-davinci/board-dm355-leopard.c @@ -36,7 +36,6 @@ #include #include #include -#include #define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x01e10000 #define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x02000000 -- cgit From 6608168486973a33d24d27b25fc94d4743c1a1e5 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:05:34 +0530 Subject: ARM: includecheck fix: board-dm644x-evm.c fix the following 'make includecheck' warning: arch/arm/mach-davinci/board-dm644x-evm.c: mach/common.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Kevin Hilman Signed-off-by: Russell King --- arch/arm/mach-davinci/board-dm644x-evm.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-davinci/board-dm644x-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c index d9d40450bdc..56c8cd01de9 100644 --- a/arch/arm/mach-davinci/board-dm644x-evm.c +++ b/arch/arm/mach-davinci/board-dm644x-evm.c @@ -45,7 +45,6 @@ #include #include #include -#include #define DM644X_EVM_PHY_MASK (0x2) #define DM644X_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ -- cgit From 78eacf0b0373f524509da261b771f8baa28806b5 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:06:42 +0530 Subject: ARM: includecheck fix: board-dm646x-evm.c fix the following 'make includecheck' warning: arch/arm/mach-davinci/board-dm646x-evm.c: mach/common.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Kevin Hilman Signed-off-by: Russell King --- arch/arm/mach-davinci/board-dm646x-evm.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c index e17de635262..8657e72debc 100644 --- a/arch/arm/mach-davinci/board-dm646x-evm.c +++ b/arch/arm/mach-davinci/board-dm646x-evm.c @@ -47,7 +47,6 @@ #include #include #include -#include #define DM646X_EVM_PHY_MASK (0x2) #define DM646X_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ -- cgit From 7a33aed825c4d2bafea748384e3331661fc3a180 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:07:26 +0530 Subject: ARM: includecheck fix: board-sffsdr.c fix the following 'make includecheck' warning: arch/arm/mach-davinci/board-sffsdr.c: mach/common.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Kevin Hilman Acked-by: Philip Balister Signed-off-by: Russell King --- arch/arm/mach-davinci/board-sffsdr.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-davinci/board-sffsdr.c b/arch/arm/mach-davinci/board-sffsdr.c index 748a8e48541..7acdfd8ac07 100644 --- a/arch/arm/mach-davinci/board-sffsdr.c +++ b/arch/arm/mach-davinci/board-sffsdr.c @@ -52,7 +52,6 @@ #include #include #include -#include #define SFFSDR_PHY_MASK (0x2) #define SFFSDR_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ -- cgit From 52cbbd41f7afeceba4be2e4062138781aacd440c Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:10:02 +0530 Subject: ARM: includecheck fix: mach-omap1/mcbsp.c fix the following 'make includecheck' warning: arch/arm/mach-omap1/mcbsp.c: mach/irqs.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Eduardo Valentin Acked-by: Kevin Hilman Signed-off-by: Russell King --- arch/arm/mach-omap1/mcbsp.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap1/mcbsp.c b/arch/arm/mach-omap1/mcbsp.c index a2d7814896b..505d98cfe50 100644 --- a/arch/arm/mach-omap1/mcbsp.c +++ b/arch/arm/mach-omap1/mcbsp.c @@ -19,7 +19,6 @@ #include #include -#include #include #include #include -- cgit From efda2b4c8a643290867d9f5816e36f71a5acee7d Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:11:05 +0530 Subject: ARM: includecheck fix: mach-omap2/mcbsp.c fix the following 'make includecheck' warning: arch/arm/mach-omap2/mcbsp.c: mach/irqs.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Eduardo Valentin Acked-by: Kevin Hilman Signed-off-by: Russell King --- arch/arm/mach-omap2/mcbsp.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/mcbsp.c b/arch/arm/mach-omap2/mcbsp.c index a5c0f0435cd..99b6e154631 100644 --- a/arch/arm/mach-omap2/mcbsp.c +++ b/arch/arm/mach-omap2/mcbsp.c @@ -19,7 +19,6 @@ #include #include -#include #include #include #include -- cgit From 2e6e2c143cdefc2624722659766d1f3c098d79e1 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:12:07 +0530 Subject: ARM: includecheck fix: plat-s3c64xx/pm.c fix the following 'make includecheck' warning: arch/arm/plat-s3c64xx/pm.c: plat/regs-gpio.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Ben Dooks Signed-off-by: Russell King --- arch/arm/plat-s3c64xx/pm.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-s3c64xx/pm.c b/arch/arm/plat-s3c64xx/pm.c index 07a6516a4f3..47632fc7eb6 100644 --- a/arch/arm/plat-s3c64xx/pm.c +++ b/arch/arm/plat-s3c64xx/pm.c @@ -117,8 +117,6 @@ void s3c_pm_save_core(void) * this. */ -#include - static void s3c64xx_cpu_suspend(void) { unsigned long tmp; -- cgit From 40e03b581a8a0b638bc1e9b957ae0536a4a00ad3 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:13:24 +0530 Subject: ARM: includecheck fix: plat-stmp3xxx/pinmux.c fix the following 'make includecheck' warning: arch/arm/plat-stmp3xxx/pinmux.c: linux/sysdev.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: dmitry pervushin Signed-off-by: Russell King --- arch/arm/plat-stmp3xxx/pinmux.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-stmp3xxx/pinmux.c b/arch/arm/plat-stmp3xxx/pinmux.c index d4120038220..6d6b1a468ed 100644 --- a/arch/arm/plat-stmp3xxx/pinmux.c +++ b/arch/arm/plat-stmp3xxx/pinmux.c @@ -22,7 +22,6 @@ #include #include #include -#include #include #include -- cgit From c640e1cb45cb9ff6b02f5f130a4f2a58ab9ebe55 Mon Sep 17 00:00:00 2001 From: Tomas Cech Date: Mon, 27 Jul 2009 14:16:31 +0100 Subject: ARM: 5623/1: Treo680: ir shutdown typo fix MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit correct GPIO freed in treo680_irda_shutdown() Signed-off-by: Tomáš ?ech Signed-off-by: Russell King --- arch/arm/mach-pxa/treo680.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-pxa/treo680.c b/arch/arm/mach-pxa/treo680.c index a06f19edebb..753ec4df17b 100644 --- a/arch/arm/mach-pxa/treo680.c +++ b/arch/arm/mach-pxa/treo680.c @@ -409,7 +409,7 @@ err1: static void treo680_irda_shutdown(struct device *dev) { - gpio_free(GPIO_NR_TREO680_AMP_EN); + gpio_free(GPIO_NR_TREO680_IR_EN); } static struct pxaficp_platform_data treo680_ficp_info = { -- cgit From 9e1b32caa525cb236e80e9c671e179bcecccc657 Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Wed, 22 Jul 2009 15:44:28 +1000 Subject: mm: Pass virtual address to [__]p{te,ud,md}_free_tlb() mm: Pass virtual address to [__]p{te,ud,md}_free_tlb() Upcoming paches to support the new 64-bit "BookE" powerpc architecture will need to have the virtual address corresponding to PTE page when freeing it, due to the way the HW table walker works. Basically, the TLB can be loaded with "large" pages that cover the whole virtual space (well, sort-of, half of it actually) represented by a PTE page, and which contain an "indirect" bit indicating that this TLB entry RPN points to an array of PTEs from which the TLB can then create direct entries. Thus, in order to invalidate those when PTE pages are deleted, we need the virtual address to pass to tlbilx or tlbivax instructions. The old trick of sticking it somewhere in the PTE page struct page sucks too much, the address is almost readily available in all call sites and almost everybody implemets these as macros, so we may as well add the argument everywhere. I added it to the pmd and pud variants for consistency. Signed-off-by: Benjamin Herrenschmidt Acked-by: David Howells [MN10300 & FRV] Acked-by: Nick Piggin Acked-by: Martin Schwidefsky [s390] Signed-off-by: Linus Torvalds --- arch/arm/include/asm/tlb.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/include/asm/tlb.h b/arch/arm/include/asm/tlb.h index 321c83e43a1..f41a6f57cd1 100644 --- a/arch/arm/include/asm/tlb.h +++ b/arch/arm/include/asm/tlb.h @@ -102,8 +102,8 @@ tlb_end_vma(struct mmu_gather *tlb, struct vm_area_struct *vma) } #define tlb_remove_page(tlb,page) free_page_and_swap_cache(page) -#define pte_free_tlb(tlb, ptep) pte_free((tlb)->mm, ptep) -#define pmd_free_tlb(tlb, pmdp) pmd_free((tlb)->mm, pmdp) +#define pte_free_tlb(tlb, ptep, addr) pte_free((tlb)->mm, ptep) +#define pmd_free_tlb(tlb, pmdp, addr) pmd_free((tlb)->mm, pmdp) #define tlb_migrate_finish(mm) do { } while (0) -- cgit From 8666f8deec75a8dce15edd35ec33d29ef79cdb08 Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Fri, 24 Jul 2009 17:30:50 +0200 Subject: mx27 defconfig update - enable MX27_3DS and MX27LITE Board - enable MXC nand driver - enable UBI support Signed-off-by: Sascha Hauer --- arch/arm/configs/mx27_defconfig | 270 +++++++++++++++++++++++++++------------- 1 file changed, 185 insertions(+), 85 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/configs/mx27_defconfig b/arch/arm/configs/mx27_defconfig index 083516cd0d7..75263a83741 100644 --- a/arch/arm/configs/mx27_defconfig +++ b/arch/arm/configs/mx27_defconfig @@ -1,15 +1,15 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc1 -# Wed Apr 8 10:18:06 2009 +# Linux kernel version: 2.6.31-rc4 +# Fri Jul 24 16:08:06 2009 # CONFIG_ARM=y +CONFIG_HAVE_PWM=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_GENERIC_GPIO=y CONFIG_GENERIC_TIME=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_MMU=y -# CONFIG_NO_IOPORT is not set CONFIG_GENERIC_HARDIRQS=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y @@ -18,14 +18,13 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_HARDIRQS_SW_RESEND=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_RWSEM_GENERIC_SPINLOCK=y -# CONFIG_ARCH_HAS_ILOG2_U32 is not set -# CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_ARCH_MTD_XIP=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_VECTORS_BASE=0xffff0000 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -85,7 +84,12 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y + +# +# Performance Counters +# CONFIG_VM_EVENT_COUNTERS=y +# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_COMPAT_BRK is not set CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -99,6 +103,12 @@ CONFIG_KPROBES=y CONFIG_KRETPROBES=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set # CONFIG_SLOW_WORK is not set CONFIG_HAVE_GENERIC_DMA_COHERENT=y CONFIG_SLABINFO=y @@ -111,7 +121,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -138,13 +148,14 @@ CONFIG_FREEZER=y # CONFIG_ARCH_VERSATILE is not set # CONFIG_ARCH_AT91 is not set # CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_EBSA110 is not set # CONFIG_ARCH_EP93XX is not set -# CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_FOOTBRIDGE is not set +CONFIG_ARCH_MXC=y +# CONFIG_ARCH_STMP3XXX is not set # CONFIG_ARCH_NETX is not set # CONFIG_ARCH_H720X is not set -# CONFIG_ARCH_IMX is not set # CONFIG_ARCH_IOP13XX is not set # CONFIG_ARCH_IOP32X is not set # CONFIG_ARCH_IOP33X is not set @@ -153,25 +164,25 @@ CONFIG_FREEZER=y # CONFIG_ARCH_IXP4XX is not set # CONFIG_ARCH_L7200 is not set # CONFIG_ARCH_KIRKWOOD is not set -# CONFIG_ARCH_KS8695 is not set -# CONFIG_ARCH_NS9XXX is not set # CONFIG_ARCH_LOKI is not set # CONFIG_ARCH_MV78XX0 is not set -CONFIG_ARCH_MXC=y # CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_W90X900 is not set # CONFIG_ARCH_PNX4008 is not set # CONFIG_ARCH_PXA is not set -# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_MSM is not set # CONFIG_ARCH_RPC is not set # CONFIG_ARCH_SA1100 is not set # CONFIG_ARCH_S3C2410 is not set # CONFIG_ARCH_S3C64XX is not set # CONFIG_ARCH_SHARK is not set # CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_U300 is not set # CONFIG_ARCH_DAVINCI is not set # CONFIG_ARCH_OMAP is not set -# CONFIG_ARCH_MSM is not set -# CONFIG_ARCH_W90X900 is not set # # Freescale MXC Implementations @@ -188,6 +199,8 @@ CONFIG_MACH_MX27=y CONFIG_MACH_MX27ADS=y CONFIG_MACH_PCM038=y CONFIG_MACH_PCM970_BASEBOARD=y +CONFIG_MACH_MX27_3DS=y +CONFIG_MACH_MX27LITE=y CONFIG_MXC_IRQ_PRIOR=y CONFIG_MXC_PWM=y @@ -213,7 +226,6 @@ CONFIG_ARM_THUMB=y # CONFIG_CPU_DCACHE_DISABLE is not set # CONFIG_CPU_DCACHE_WRITETHROUGH is not set # CONFIG_CPU_CACHE_ROUND_ROBIN is not set -# CONFIG_OUTER_CACHE is not set CONFIG_COMMON_CLKDEV=y # @@ -238,7 +250,6 @@ CONFIG_PREEMPT=y CONFIG_HZ=100 CONFIG_AEABI=y CONFIG_OABI_COMPAT=y -CONFIG_ARCH_FLATMEM_HAS_HOLES=y # CONFIG_ARCH_SPARSEMEM_DEFAULT is not set # CONFIG_ARCH_SELECT_MEMORY_MODEL is not set # CONFIG_HIGHMEM is not set @@ -253,10 +264,11 @@ CONFIG_SPLIT_PTLOCK_CPUS=4096 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_ALIGNMENT_TRAP=y +# CONFIG_UACCESS_WITH_MEMCPY is not set # # Boot options @@ -361,6 +373,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -474,7 +487,16 @@ CONFIG_MTD_PHYSMAP=y # CONFIG_MTD_DOC2000 is not set # CONFIG_MTD_DOC2001 is not set # CONFIG_MTD_DOC2001PLUS is not set -# CONFIG_MTD_NAND is not set +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +# CONFIG_MTD_NAND_GPIO is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +CONFIG_MTD_NAND_MXC=y # CONFIG_MTD_ONENAND is not set # @@ -485,7 +507,15 @@ CONFIG_MTD_PHYSMAP=y # # UBI - Unsorted block images # -# CONFIG_MTD_UBI is not set +CONFIG_MTD_UBI=y +CONFIG_MTD_UBI_WL_THRESHOLD=4096 +CONFIG_MTD_UBI_BEB_RESERVE=1 +# CONFIG_MTD_UBI_GLUEBI is not set + +# +# UBI debugging options +# +# CONFIG_MTD_UBI_DEBUG is not set # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_COW_COMMON is not set @@ -494,7 +524,21 @@ CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_RAM is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set -# CONFIG_MISC_DEVICES is not set +# CONFIG_MG_DISK is not set +CONFIG_MISC_DEVICES=y +# CONFIG_ICS932S401 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_ISL29003 is not set +# CONFIG_C2PORT is not set + +# +# EEPROM support +# +CONFIG_EEPROM_AT24=y +# CONFIG_EEPROM_AT25 is not set +# CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set +# CONFIG_EEPROM_93CX6 is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -508,7 +552,6 @@ CONFIG_HAVE_IDE=y # CONFIG_ATA is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -534,6 +577,8 @@ CONFIG_NET_ETHERNET=y # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set +# CONFIG_KS8842 is not set +# CONFIG_KS8851 is not set CONFIG_FEC=y # CONFIG_FEC2 is not set # CONFIG_NETDEV_1000 is not set @@ -580,6 +625,11 @@ CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_TABLET is not set CONFIG_INPUT_TOUCHSCREEN=y # CONFIG_TOUCHSCREEN_ADS7846 is not set +# CONFIG_TOUCHSCREEN_AD7877 is not set +# CONFIG_TOUCHSCREEN_AD7879_I2C is not set +# CONFIG_TOUCHSCREEN_AD7879_SPI is not set +# CONFIG_TOUCHSCREEN_AD7879 is not set +# CONFIG_TOUCHSCREEN_EETI is not set # CONFIG_TOUCHSCREEN_FUJITSU is not set # CONFIG_TOUCHSCREEN_GUNZE is not set # CONFIG_TOUCHSCREEN_ELO is not set @@ -592,6 +642,7 @@ CONFIG_INPUT_TOUCHSCREEN=y # CONFIG_TOUCHSCREEN_TOUCHWIN is not set # CONFIG_TOUCHSCREEN_TOUCHIT213 is not set # CONFIG_TOUCHSCREEN_TSC2007 is not set +# CONFIG_TOUCHSCREEN_W90X900 is not set # CONFIG_INPUT_MISC is not set # @@ -644,6 +695,7 @@ CONFIG_I2C_HELPER_AUTO=y # # I2C system bus drivers (mostly embedded / system-on-chip) # +# CONFIG_I2C_DESIGNWARE is not set # CONFIG_I2C_GPIO is not set CONFIG_I2C_IMX=y # CONFIG_I2C_OCORES is not set @@ -668,7 +720,6 @@ CONFIG_I2C_IMX=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set @@ -719,6 +770,7 @@ CONFIG_W1=y # # CONFIG_W1_MASTER_DS2482 is not set CONFIG_W1_MASTER_MXC=y +# CONFIG_W1_MASTER_DS1WM is not set # CONFIG_W1_MASTER_GPIO is not set # @@ -753,54 +805,16 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_TPS65010 is not set # CONFIG_TWL4030_CORE is not set # CONFIG_MFD_TMIO is not set +# CONFIG_MFD_T7L66XB is not set +# CONFIG_MFD_TC6387XB is not set # CONFIG_MFD_TC6393XB is not set # CONFIG_PMIC_DA903X is not set # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -CONFIG_VIDEO_DEV=y -CONFIG_VIDEO_V4L2_COMMON=y -CONFIG_VIDEO_ALLOW_V4L1=y -CONFIG_VIDEO_V4L1_COMPAT=y -# CONFIG_DVB_CORE is not set -CONFIG_VIDEO_MEDIA=y - -# -# Multimedia drivers -# -# CONFIG_MEDIA_ATTACH is not set -CONFIG_MEDIA_TUNER=y -# CONFIG_MEDIA_TUNER_CUSTOMISE is not set -CONFIG_MEDIA_TUNER_SIMPLE=y -CONFIG_MEDIA_TUNER_TDA8290=y -CONFIG_MEDIA_TUNER_TDA9887=y -CONFIG_MEDIA_TUNER_TEA5761=y -CONFIG_MEDIA_TUNER_TEA5767=y -CONFIG_MEDIA_TUNER_MT20XX=y -CONFIG_MEDIA_TUNER_XC2028=y -CONFIG_MEDIA_TUNER_XC5000=y -CONFIG_MEDIA_TUNER_MC44S803=y -CONFIG_VIDEO_V4L2=y -CONFIG_VIDEO_V4L1=y -CONFIG_VIDEO_CAPTURE_DRIVERS=y -# CONFIG_VIDEO_ADV_DEBUG is not set -# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set -CONFIG_VIDEO_HELPER_CHIPS_AUTO=y -# CONFIG_VIDEO_VIVI is not set -# CONFIG_VIDEO_CPIA is not set -# CONFIG_VIDEO_SAA5246A is not set -# CONFIG_VIDEO_SAA5249 is not set -# CONFIG_SOC_CAMERA is not set -# CONFIG_RADIO_ADAPTERS is not set -# CONFIG_DAB is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support @@ -917,6 +931,7 @@ CONFIG_RTC_DRV_PCF8563=y # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -962,12 +977,15 @@ CONFIG_RTC_DRV_PCF8563=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y # CONFIG_DNOTIFY is not set # CONFIG_INOTIFY is not set +CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set @@ -1021,6 +1039,12 @@ CONFIG_JFFS2_ZLIB=y # CONFIG_JFFS2_LZO is not set CONFIG_JFFS2_RTIME=y # CONFIG_JFFS2_RUBIN is not set +CONFIG_UBIFS_FS=y +# CONFIG_UBIFS_FS_XATTR is not set +# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set +CONFIG_UBIFS_FS_LZO=y +CONFIG_UBIFS_FS_ZLIB=y +# CONFIG_UBIFS_FS_DEBUG is not set # CONFIG_CRAMFS is not set # CONFIG_SQUASHFS is not set # CONFIG_VXFS_FS is not set @@ -1119,25 +1143,11 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_NOP_TRACER=y CONFIG_HAVE_FUNCTION_TRACER=y CONFIG_RING_BUFFER=y +CONFIG_EVENT_TRACING=y +CONFIG_CONTEXT_SWITCH_TRACER=y CONFIG_TRACING=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_IRQSOFF_TRACER is not set -# CONFIG_PREEMPT_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set -# CONFIG_FTRACE_STARTUP_TEST is not set +# CONFIG_FTRACE is not set # CONFIG_DYNAMIC_DEBUG is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y @@ -1151,16 +1161,104 @@ CONFIG_ARM_UNWIND=y # CONFIG_SECURITY is not set # CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set -# CONFIG_CRYPTO is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +# CONFIG_CRYPTO_FIPS is not set +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_ALGAPI2=y +# CONFIG_CRYPTO_MANAGER is not set +# CONFIG_CRYPTO_MANAGER2 is not set +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +# CONFIG_CRYPTO_CBC is not set +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +# CONFIG_CRYPTO_ECB is not set +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +# CONFIG_CRYPTO_MD5 is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_DES is not set +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +CONFIG_CRYPTO_DEFLATE=y +# CONFIG_CRYPTO_ZLIB is not set +CONFIG_CRYPTO_LZO=y + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set +CONFIG_CRYPTO_HW=y CONFIG_BINARY_PRINTF=y # # Library routines # CONFIG_BITREVERSE=y +CONFIG_RATIONAL=y CONFIG_GENERIC_FIND_LAST_BIT=y # CONFIG_CRC_CCITT is not set -# CONFIG_CRC16 is not set +CONFIG_CRC16=y # CONFIG_CRC_T10DIF is not set # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y @@ -1168,6 +1266,8 @@ CONFIG_CRC32=y # CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y +CONFIG_LZO_COMPRESS=y +CONFIG_LZO_DECOMPRESS=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y -- cgit From 42469ff014812880d7324285d165841f4b1814e7 Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Fri, 24 Jul 2009 17:31:03 +0200 Subject: mx3 defconfig update - enable PCM043, MX31LILLY, ARMADILLO5X0 and MX35_3DS boards - enable MXC nand driver - enable UBI support - disable cs89x0 support which broke all boards which do not have this chip Signed-off-by: Sascha Hauer --- arch/arm/configs/mx3_defconfig | 151 ++++++++++++++++++++++++++++------------- 1 file changed, 102 insertions(+), 49 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/configs/mx3_defconfig b/arch/arm/configs/mx3_defconfig index 20ada526f6d..a4f9a2a8149 100644 --- a/arch/arm/configs/mx3_defconfig +++ b/arch/arm/configs/mx3_defconfig @@ -1,15 +1,15 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc1 -# Wed Apr 8 11:06:37 2009 +# Linux kernel version: 2.6.31-rc4 +# Tue Jul 28 14:11:34 2009 # CONFIG_ARM=y +CONFIG_HAVE_PWM=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_GENERIC_GPIO=y CONFIG_GENERIC_TIME=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_MMU=y -# CONFIG_NO_IOPORT is not set CONFIG_GENERIC_HARDIRQS=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y @@ -18,14 +18,13 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_HARDIRQS_SW_RESEND=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_RWSEM_GENERIC_SPINLOCK=y -# CONFIG_ARCH_HAS_ILOG2_U32 is not set -# CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_ARCH_MTD_XIP=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_VECTORS_BASE=0xffff0000 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -86,7 +85,12 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y + +# +# Performance Counters +# CONFIG_VM_EVENT_COUNTERS=y +# CONFIG_STRIP_ASM_SYMS is not set CONFIG_COMPAT_BRK=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -97,6 +101,11 @@ CONFIG_HAVE_OPROFILE=y # CONFIG_KPROBES is not set CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# # CONFIG_SLOW_WORK is not set CONFIG_HAVE_GENERIC_DMA_COHERENT=y CONFIG_SLABINFO=y @@ -109,7 +118,7 @@ CONFIG_MODULE_FORCE_UNLOAD=y CONFIG_MODVERSIONS=y # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -136,13 +145,14 @@ CONFIG_FREEZER=y # CONFIG_ARCH_VERSATILE is not set # CONFIG_ARCH_AT91 is not set # CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_EBSA110 is not set # CONFIG_ARCH_EP93XX is not set -# CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_FOOTBRIDGE is not set +CONFIG_ARCH_MXC=y +# CONFIG_ARCH_STMP3XXX is not set # CONFIG_ARCH_NETX is not set # CONFIG_ARCH_H720X is not set -# CONFIG_ARCH_IMX is not set # CONFIG_ARCH_IOP13XX is not set # CONFIG_ARCH_IOP32X is not set # CONFIG_ARCH_IOP33X is not set @@ -151,25 +161,25 @@ CONFIG_FREEZER=y # CONFIG_ARCH_IXP4XX is not set # CONFIG_ARCH_L7200 is not set # CONFIG_ARCH_KIRKWOOD is not set -# CONFIG_ARCH_KS8695 is not set -# CONFIG_ARCH_NS9XXX is not set # CONFIG_ARCH_LOKI is not set # CONFIG_ARCH_MV78XX0 is not set -CONFIG_ARCH_MXC=y # CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_W90X900 is not set # CONFIG_ARCH_PNX4008 is not set # CONFIG_ARCH_PXA is not set -# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_MSM is not set # CONFIG_ARCH_RPC is not set # CONFIG_ARCH_SA1100 is not set # CONFIG_ARCH_S3C2410 is not set # CONFIG_ARCH_S3C64XX is not set # CONFIG_ARCH_SHARK is not set # CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_U300 is not set # CONFIG_ARCH_DAVINCI is not set # CONFIG_ARCH_OMAP is not set -# CONFIG_ARCH_MSM is not set -# CONFIG_ARCH_W90X900 is not set # # Freescale MXC Implementations @@ -178,6 +188,7 @@ CONFIG_ARCH_MXC=y # CONFIG_ARCH_MX2 is not set CONFIG_ARCH_MX3=y CONFIG_ARCH_MX31=y +CONFIG_ARCH_MX35=y # # MX3 platforms: @@ -185,12 +196,19 @@ CONFIG_ARCH_MX31=y CONFIG_MACH_MX31ADS=y CONFIG_MACH_MX31ADS_WM1133_EV1=y CONFIG_MACH_PCM037=y +CONFIG_MACH_PCM037_EET=y CONFIG_MACH_MX31LITE=y CONFIG_MACH_MX31_3DS=y CONFIG_MACH_MX31MOBOARD=y +CONFIG_MACH_MX31LILLY=y CONFIG_MACH_QONG=y +CONFIG_MACH_PCM043=y +CONFIG_MACH_ARMADILLO5X0=y +CONFIG_MACH_MX35_3DS=y CONFIG_MXC_IRQ_PRIOR=y CONFIG_MXC_PWM=y +CONFIG_ARCH_HAS_RNGA=y +CONFIG_ARCH_MXC_IOMUX_V3=y # # Processor Type @@ -218,6 +236,7 @@ CONFIG_ARM_THUMB=y # CONFIG_CPU_BPREDICT_DISABLE is not set CONFIG_OUTER_CACHE=y CONFIG_CACHE_L2X0=y +# CONFIG_ARM_ERRATA_411920 is not set CONFIG_COMMON_CLKDEV=y # @@ -242,7 +261,6 @@ CONFIG_PREEMPT=y CONFIG_HZ=100 CONFIG_AEABI=y CONFIG_OABI_COMPAT=y -CONFIG_ARCH_FLATMEM_HAS_HOLES=y # CONFIG_ARCH_SPARSEMEM_DEFAULT is not set # CONFIG_ARCH_SELECT_MEMORY_MODEL is not set # CONFIG_HIGHMEM is not set @@ -257,10 +275,11 @@ CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_ALIGNMENT_TRAP=y +# CONFIG_UACCESS_WITH_MEMCPY is not set # # Boot options @@ -362,6 +381,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -465,7 +485,16 @@ CONFIG_MTD_PHYSMAP=y # CONFIG_MTD_DOC2000 is not set # CONFIG_MTD_DOC2001 is not set # CONFIG_MTD_DOC2001PLUS is not set -# CONFIG_MTD_NAND is not set +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +# CONFIG_MTD_NAND_GPIO is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_DISKONCHIP is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +CONFIG_MTD_NAND_MXC=y # CONFIG_MTD_ONENAND is not set # @@ -476,10 +505,30 @@ CONFIG_MTD_PHYSMAP=y # # UBI - Unsorted block images # -# CONFIG_MTD_UBI is not set +CONFIG_MTD_UBI=y +CONFIG_MTD_UBI_WL_THRESHOLD=4096 +CONFIG_MTD_UBI_BEB_RESERVE=1 +# CONFIG_MTD_UBI_GLUEBI is not set + +# +# UBI debugging options +# +# CONFIG_MTD_UBI_DEBUG is not set # CONFIG_PARPORT is not set # CONFIG_BLK_DEV is not set -# CONFIG_MISC_DEVICES is not set +CONFIG_MISC_DEVICES=y +# CONFIG_ICS932S401 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_ISL29003 is not set +# CONFIG_C2PORT is not set + +# +# EEPROM support +# +CONFIG_EEPROM_AT24=y +# CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set +# CONFIG_EEPROM_93CX6 is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -493,7 +542,6 @@ CONFIG_HAVE_IDE=y # CONFIG_ATA is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -528,7 +576,7 @@ CONFIG_MII=y # CONFIG_ETHOC is not set # CONFIG_SMC911X is not set CONFIG_SMSC911X=y -# CONFIG_DNET is not set +CONFIG_DNET=y # CONFIG_IBM_NEW_EMAC_ZMII is not set # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set @@ -537,8 +585,10 @@ CONFIG_SMSC911X=y # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set -CONFIG_CS89x0=y -CONFIG_CS89x0_NONISA_IRQ=y +# CONFIG_CS89x0 is not set +# CONFIG_KS8842 is not set +CONFIG_FEC=y +# CONFIG_FEC2 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -609,6 +659,7 @@ CONFIG_I2C_HELPER_AUTO=y # # I2C system bus drivers (mostly embedded / system-on-chip) # +# CONFIG_I2C_DESIGNWARE is not set # CONFIG_I2C_GPIO is not set CONFIG_I2C_IMX=y # CONFIG_I2C_OCORES is not set @@ -633,7 +684,6 @@ CONFIG_I2C_IMX=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set @@ -669,6 +719,7 @@ CONFIG_W1=y # # CONFIG_W1_MASTER_DS2482 is not set CONFIG_W1_MASTER_MXC=y +# CONFIG_W1_MASTER_DS1WM is not set # CONFIG_W1_MASTER_GPIO is not set # @@ -703,6 +754,8 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_TPS65010 is not set # CONFIG_TWL4030_CORE is not set # CONFIG_MFD_TMIO is not set +# CONFIG_MFD_T7L66XB is not set +# CONFIG_MFD_TC6387XB is not set # CONFIG_MFD_TC6393XB is not set # CONFIG_PMIC_DA903X is not set # CONFIG_MFD_WM8400 is not set @@ -711,10 +764,8 @@ CONFIG_MFD_WM8350_CONFIG_MODE_0=y CONFIG_MFD_WM8352_CONFIG_MODE_0=y CONFIG_MFD_WM8350_I2C=y # CONFIG_MFD_PCF50633 is not set - -# -# Multimedia devices -# +# CONFIG_AB3100_CORE is not set +CONFIG_MEDIA_SUPPORT=y # # Multimedia core support @@ -758,8 +809,10 @@ CONFIG_SOC_CAMERA_MT9T031=y CONFIG_SOC_CAMERA_MT9V022=y CONFIG_SOC_CAMERA_TW9910=y # CONFIG_SOC_CAMERA_PLATFORM is not set -# CONFIG_SOC_CAMERA_OV772X is not set +CONFIG_SOC_CAMERA_OV772X=y +CONFIG_MX3_VIDEO=y CONFIG_VIDEO_MX3=y +# CONFIG_VIDEO_SH_MOBILE_CEU is not set # CONFIG_RADIO_ADAPTERS is not set # CONFIG_DAB is not set @@ -847,8 +900,11 @@ CONFIG_REGULATOR=y # CONFIG_REGULATOR_DEBUG is not set # CONFIG_REGULATOR_FIXED_VOLTAGE is not set # CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set +# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set # CONFIG_REGULATOR_BQ24022 is not set +# CONFIG_REGULATOR_MAX1586 is not set CONFIG_REGULATOR_WM8350=y +# CONFIG_REGULATOR_LP3971 is not set # CONFIG_UIO is not set # CONFIG_STAGING is not set @@ -861,10 +917,12 @@ CONFIG_REGULATOR_WM8350=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y # CONFIG_DNOTIFY is not set CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -921,6 +979,12 @@ CONFIG_JFFS2_ZLIB=y # CONFIG_JFFS2_LZO is not set CONFIG_JFFS2_RTIME=y # CONFIG_JFFS2_RUBIN is not set +CONFIG_UBIFS_FS=y +# CONFIG_UBIFS_FS_XATTR is not set +# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set +CONFIG_UBIFS_FS_LZO=y +CONFIG_UBIFS_FS_ZLIB=y +# CONFIG_UBIFS_FS_DEBUG is not set # CONFIG_CRAMFS is not set # CONFIG_SQUASHFS is not set # CONFIG_VXFS_FS is not set @@ -937,6 +1001,7 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y +# CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFSD is not set CONFIG_LOCKD=y @@ -979,22 +1044,7 @@ CONFIG_FRAME_WARN=1024 CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_HAVE_FUNCTION_TRACER=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_IRQSOFF_TRACER is not set -# CONFIG_PREEMPT_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_FTRACE is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y CONFIG_ARM_UNWIND=y @@ -1094,9 +1144,9 @@ CONFIG_CRYPTO_DES=y # # Compression # -# CONFIG_CRYPTO_DEFLATE is not set +CONFIG_CRYPTO_DEFLATE=y # CONFIG_CRYPTO_ZLIB is not set -# CONFIG_CRYPTO_LZO is not set +CONFIG_CRYPTO_LZO=y # # Random Number Generation @@ -1109,9 +1159,10 @@ CONFIG_CRYPTO_HW=y # Library routines # CONFIG_BITREVERSE=y +CONFIG_RATIONAL=y CONFIG_GENERIC_FIND_LAST_BIT=y # CONFIG_CRC_CCITT is not set -# CONFIG_CRC16 is not set +CONFIG_CRC16=y # CONFIG_CRC_T10DIF is not set # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y @@ -1119,6 +1170,8 @@ CONFIG_CRC32=y # CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y +CONFIG_LZO_COMPRESS=y +CONFIG_LZO_DECOMPRESS=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y -- cgit From 0c997c0eaac8c68fa23719617484dae29bddaedd Mon Sep 17 00:00:00 2001 From: Lars-Peter Clausen Date: Wed, 22 Jul 2009 00:33:06 +0200 Subject: S3C24XX: GPIO: Fix pin range check in s3c_gpiolib_getchip In the s3c_gpiolib_getchip implementation for s3c24xx the check whether a pin is in the gpio banks range is reversed. Thus the function returns NULL for valid pins and the gpio chip if its not valid. As a result gpio states are not saved/restored properly during suspend/resume. Signed-off-by: Ben Dooks --- arch/arm/mach-s3c2410/include/mach/gpio-core.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-s3c2410/include/mach/gpio-core.h b/arch/arm/mach-s3c2410/include/mach/gpio-core.h index 8fe192081d3..f8b879a7973 100644 --- a/arch/arm/mach-s3c2410/include/mach/gpio-core.h +++ b/arch/arm/mach-s3c2410/include/mach/gpio-core.h @@ -28,7 +28,7 @@ static inline struct s3c_gpio_chip *s3c_gpiolib_getchip(unsigned int pin) return NULL; chip = &s3c24xx_gpios[pin/32]; - return (S3C2410_GPIO_OFFSET(pin) > chip->chip.ngpio) ? chip : NULL; + return (S3C2410_GPIO_OFFSET(pin) < chip->chip.ngpio) ? chip : NULL; } #endif /* __ASM_ARCH_GPIO_CORE_H */ -- cgit From 1d91e1a296244690461a7c36d71710dfbabbc219 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Wed, 15 Jul 2009 13:03:34 +0100 Subject: S3C64XX: Fix get_rate() for ARMCLK If the requested clock is faster than the parent clock then the parent clock is the closest we can get to the request so we need to return that instead of the requested clock. Signed-off-by: Mark Brown Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/s3c6400-clock.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-s3c64xx/s3c6400-clock.c b/arch/arm/plat-s3c64xx/s3c6400-clock.c index 1debc1f9f98..f8165e62247 100644 --- a/arch/arm/plat-s3c64xx/s3c6400-clock.c +++ b/arch/arm/plat-s3c64xx/s3c6400-clock.c @@ -153,7 +153,7 @@ static unsigned long s3c64xx_clk_arm_round_rate(struct clk *clk, u32 div; if (parent < rate) - return rate; + return parent; div = (parent / rate) - 1; if (div > armclk_mask) -- cgit From 9b71de49b030ad8fd4d13d38571b5c42dc9ed8dd Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Wed, 15 Jul 2009 13:03:35 +0100 Subject: S3C64XX: Fix ARMCLK configuration The value of armclk_mask needs to be inverted for use as a mask on the register value when updating ARM_RATIO. This is critical for cpufreq support, without it attempts to scale the frequency of the core trash pretty much the entire clock tree. Signed-off-by: Mark Brown Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/s3c6400-clock.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-s3c64xx/s3c6400-clock.c b/arch/arm/plat-s3c64xx/s3c6400-clock.c index f8165e62247..febac1950d8 100644 --- a/arch/arm/plat-s3c64xx/s3c6400-clock.c +++ b/arch/arm/plat-s3c64xx/s3c6400-clock.c @@ -175,7 +175,7 @@ static int s3c64xx_clk_arm_set_rate(struct clk *clk, unsigned long rate) div = clk_get_rate(clk->parent) / rate; val = __raw_readl(S3C_CLK_DIV0); - val &= armclk_mask; + val &= ~armclk_mask; val |= (div - 1); __raw_writel(val, S3C_CLK_DIV0); -- cgit From 3ef7143d2287b21e09e00a25a8cb4fbdcf0c6c4c Mon Sep 17 00:00:00 2001 From: Uwe Kleine-König Date: Wed, 29 Jul 2009 19:31:30 +0100 Subject: ARM: 5627/1: Fix restoring of lr at the end of mcount MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit After ftrace_trace_function is called r1 is probably clobbered so don't try to use its value for restoring. This was introduced in v2.6.29~38^2~7 Signed-off-by: Uwe Kleine-König Signed-off-by: Russell King --- arch/arm/kernel/entry-common.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/kernel/entry-common.S b/arch/arm/kernel/entry-common.S index 366e5097a41..8c3de1a350b 100644 --- a/arch/arm/kernel/entry-common.S +++ b/arch/arm/kernel/entry-common.S @@ -148,7 +148,7 @@ trace: sub r0, r0, #MCOUNT_INSN_SIZE mov lr, pc mov pc, r2 - mov lr, r1 @ restore lr + ldr lr, [fp, #-4] @ restore lr ldmia sp!, {r0-r3, pc} #endif /* CONFIG_DYNAMIC_FTRACE */ -- cgit From 320145fac91955ee35a6af7e1c2b42388a17b3d8 Mon Sep 17 00:00:00 2001 From: Yegor Yefremov Date: Thu, 9 Jul 2009 08:48:03 +0100 Subject: ARM: 5597/1: [PCI] reset all internal hardware prior PCI initialization Make software reset to avoid freeze if PCI bus was messed up Signed-off-by: Yegor Yefremov Acked-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-ks8695/pci.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-ks8695/pci.c b/arch/arm/mach-ks8695/pci.c index f5ebcc0fcab..78499667eb7 100644 --- a/arch/arm/mach-ks8695/pci.c +++ b/arch/arm/mach-ks8695/pci.c @@ -245,6 +245,9 @@ static int ks8695_pci_fault(unsigned long addr, unsigned int fsr, struct pt_regs static void __init ks8695_pci_preinit(void) { + /* make software reset to avoid freeze if PCI bus was messed up */ + __raw_writel(0x80000000, KS8695_PCI_VA + KS8695_PBCS); + /* stage 1 initialization, subid, subdevice = 0x0001 */ __raw_writel(0x00010001, KS8695_PCI_VA + KS8695_CRCSID); -- cgit From 165f5f64199f972a21f21effc125d89ed2488e58 Mon Sep 17 00:00:00 2001 From: Peter Korsgaard Date: Wed, 1 Jul 2009 17:47:08 +0200 Subject: ARM: S3C: PWM fix for low duty cycle The pwm hardware only checks the compare register after a decrement, so the pin never toggles if tcmp = tcnt. This happens when a very low duty cycle is requested. Fix it by always ensuring that tcmp < tcnt. Signed-off-by: Peter Korsgaard Signed-off-by: Ben Dooks --- arch/arm/plat-s3c24xx/pwm.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/plat-s3c24xx/pwm.c b/arch/arm/plat-s3c24xx/pwm.c index 0120b760315..82a6d4de02a 100644 --- a/arch/arm/plat-s3c24xx/pwm.c +++ b/arch/arm/plat-s3c24xx/pwm.c @@ -246,6 +246,10 @@ int pwm_config(struct pwm_device *pwm, int duty_ns, int period_ns) tcmp = duty_ns / tin_ns; tcmp = tcnt - tcmp; + /* the pwm hw only checks the compare register after a decrement, + so the pin never toggles if tcmp = tcnt */ + if (tcmp == tcnt) + tcmp--; pwm_dbg(pwm, "tin_ns=%lu, tcmp=%ld/%lu\n", tin_ns, tcmp, tcnt); -- cgit From ff46a474ca2566d79e8d7454442b56d82bce37c1 Mon Sep 17 00:00:00 2001 From: Guennadi Liakhovetski Date: Fri, 31 Jul 2009 15:42:09 +0200 Subject: mx3: Fix double pin allocation in pcm037_eet.c SPI pins are now allocated in pcm037.c, remove them from EET. Signed-off-by: Guennadi Liakhovetski Signed-off-by: Sascha Hauer --- arch/arm/mach-mx3/pcm037_eet.c | 9 --------- 1 file changed, 9 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-mx3/pcm037_eet.c b/arch/arm/mach-mx3/pcm037_eet.c index fe52fb1bb8b..8d386000fc4 100644 --- a/arch/arm/mach-mx3/pcm037_eet.c +++ b/arch/arm/mach-mx3/pcm037_eet.c @@ -24,15 +24,6 @@ #include "devices.h" static unsigned int pcm037_eet_pins[] = { - /* SPI #1 */ - MX31_PIN_CSPI1_MISO__MISO, - MX31_PIN_CSPI1_MOSI__MOSI, - MX31_PIN_CSPI1_SCLK__SCLK, - MX31_PIN_CSPI1_SPI_RDY__SPI_RDY, - MX31_PIN_CSPI1_SS0__SS0, - MX31_PIN_CSPI1_SS1__SS1, - MX31_PIN_CSPI1_SS2__SS2, - /* Reserve and hardwire GPIO 57 high - S6E63D6 chipselect */ IOMUX_MODE(MX31_PIN_KEY_COL7, IOMUX_CONFIG_GPIO), /* GPIO keys */ -- cgit From b37c45b8c27c049dc44673e40fd63820fd9a9d91 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 5 Aug 2009 16:53:24 +0300 Subject: OMAP: GPIO: Fix incorrect gpio_get logic for output GPIOs gpio_get() should return DATAIN register value when the GPIO is configured as input whereas it should return DATAOUT register value when the GPIO is configured as output. Now /sys/kernel/debug/gpio shows proper values for output GPIOs Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/plat-omap/gpio.c | 121 ++++++++++++++++++++++++++++++++++------------ 1 file changed, 89 insertions(+), 32 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-omap/gpio.c b/arch/arm/plat-omap/gpio.c index 26b387c1242..9c16ca8d293 100644 --- a/arch/arm/plat-omap/gpio.c +++ b/arch/arm/plat-omap/gpio.c @@ -476,14 +476,12 @@ static void _set_gpio_dataout(struct gpio_bank *bank, int gpio, int enable) __raw_writel(l, reg); } -static int __omap_get_gpio_datain(int gpio) +static int _get_gpio_datain(struct gpio_bank *bank, int gpio) { - struct gpio_bank *bank; void __iomem *reg; if (check_gpio(gpio) < 0) return -EINVAL; - bank = get_gpio_bank(gpio); reg = bank->base; switch (bank->method) { #ifdef CONFIG_ARCH_OMAP1 @@ -524,6 +522,53 @@ static int __omap_get_gpio_datain(int gpio) & (1 << get_gpio_index(gpio))) != 0; } +static int _get_gpio_dataout(struct gpio_bank *bank, int gpio) +{ + void __iomem *reg; + + if (check_gpio(gpio) < 0) + return -EINVAL; + reg = bank->base; + + switch (bank->method) { +#ifdef CONFIG_ARCH_OMAP1 + case METHOD_MPUIO: + reg += OMAP_MPUIO_OUTPUT; + break; +#endif +#ifdef CONFIG_ARCH_OMAP15XX + case METHOD_GPIO_1510: + reg += OMAP1510_GPIO_DATA_OUTPUT; + break; +#endif +#ifdef CONFIG_ARCH_OMAP16XX + case METHOD_GPIO_1610: + reg += OMAP1610_GPIO_DATAOUT; + break; +#endif +#ifdef CONFIG_ARCH_OMAP730 + case METHOD_GPIO_730: + reg += OMAP730_GPIO_DATA_OUTPUT; + break; +#endif +#ifdef CONFIG_ARCH_OMAP850 + case METHOD_GPIO_850: + reg += OMAP850_GPIO_DATA_OUTPUT; + break; +#endif +#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \ + defined(CONFIG_ARCH_OMAP4) + case METHOD_GPIO_24XX: + reg += OMAP24XX_GPIO_DATAOUT; + break; +#endif + default: + return -EINVAL; + } + + return (__raw_readl(reg) & (1 << get_gpio_index(gpio))) != 0; +} + #define MOD_REG_BIT(reg, bit_mask, set) \ do { \ int l = __raw_readl(base + reg); \ @@ -1350,9 +1395,49 @@ static int gpio_input(struct gpio_chip *chip, unsigned offset) return 0; } +static int gpio_is_input(struct gpio_bank *bank, int mask) +{ + void __iomem *reg = bank->base; + + switch (bank->method) { + case METHOD_MPUIO: + reg += OMAP_MPUIO_IO_CNTL; + break; + case METHOD_GPIO_1510: + reg += OMAP1510_GPIO_DIR_CONTROL; + break; + case METHOD_GPIO_1610: + reg += OMAP1610_GPIO_DIRECTION; + break; + case METHOD_GPIO_730: + reg += OMAP730_GPIO_DIR_CONTROL; + break; + case METHOD_GPIO_850: + reg += OMAP850_GPIO_DIR_CONTROL; + break; + case METHOD_GPIO_24XX: + reg += OMAP24XX_GPIO_OE; + break; + } + return __raw_readl(reg) & mask; +} + static int gpio_get(struct gpio_chip *chip, unsigned offset) { - return __omap_get_gpio_datain(chip->base + offset); + struct gpio_bank *bank; + void __iomem *reg; + int gpio; + u32 mask; + + gpio = chip->base + offset; + bank = get_gpio_bank(gpio); + reg = bank->base; + mask = 1 << get_gpio_index(gpio); + + if (gpio_is_input(bank, mask)) + return _get_gpio_datain(bank, gpio); + else + return _get_gpio_dataout(bank, gpio); } static int gpio_output(struct gpio_chip *chip, unsigned offset, int value) @@ -1886,34 +1971,6 @@ arch_initcall(omap_gpio_sysinit); #include #include -static int gpio_is_input(struct gpio_bank *bank, int mask) -{ - void __iomem *reg = bank->base; - - switch (bank->method) { - case METHOD_MPUIO: - reg += OMAP_MPUIO_IO_CNTL; - break; - case METHOD_GPIO_1510: - reg += OMAP1510_GPIO_DIR_CONTROL; - break; - case METHOD_GPIO_1610: - reg += OMAP1610_GPIO_DIRECTION; - break; - case METHOD_GPIO_730: - reg += OMAP730_GPIO_DIR_CONTROL; - break; - case METHOD_GPIO_850: - reg += OMAP850_GPIO_DIR_CONTROL; - break; - case METHOD_GPIO_24XX: - reg += OMAP24XX_GPIO_OE; - break; - } - return __raw_readl(reg) & mask; -} - - static int dbg_gpio_show(struct seq_file *s, void *unused) { unsigned i, j, gpio; -- cgit From 7cc515f74d2871daff106a17714bfd16bcb045ca Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Wed, 10 Jun 2009 09:02:25 -0700 Subject: OMAP2/3: PM: make PM __init calls static Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm.h | 3 --- arch/arm/mach-omap2/pm24xx.c | 2 +- arch/arm/mach-omap2/pm34xx.c | 2 +- 3 files changed, 2 insertions(+), 5 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/pm.h b/arch/arm/mach-omap2/pm.h index f7b3baf7667..21201cd4117 100644 --- a/arch/arm/mach-omap2/pm.h +++ b/arch/arm/mach-omap2/pm.h @@ -11,9 +11,6 @@ #ifndef __ARCH_ARM_MACH_OMAP2_PM_H #define __ARCH_ARM_MACH_OMAP2_PM_H -extern int omap2_pm_init(void); -extern int omap3_pm_init(void); - #ifdef CONFIG_PM_DEBUG extern void omap2_pm_dump(int mode, int resume, unsigned int us); extern int omap2_pm_debug; diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c index db1025562fb..528dbdc26e2 100644 --- a/arch/arm/mach-omap2/pm24xx.c +++ b/arch/arm/mach-omap2/pm24xx.c @@ -470,7 +470,7 @@ static void __init prcm_setup_regs(void) WKUP_MOD, PM_WKEN); } -int __init omap2_pm_init(void) +static int __init omap2_pm_init(void) { u32 l; diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 841d4c5ed8b..765cdc0cd7a 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -652,7 +652,7 @@ static int __init clkdms_setup(struct clockdomain *clkdm) return 0; } -int __init omap3_pm_init(void) +static int __init omap3_pm_init(void) { struct power_state *pwrst, *tmp; int ret; -- cgit From 364dd47466ff7a7749bf037df4bf3b7aedbfe6f4 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Tue, 9 Jun 2009 11:45:30 -0700 Subject: OMAP3: PM: CM_REGADDR macros using wrong name Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/cm.h | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/cm.h b/arch/arm/mach-omap2/cm.h index 1d3c93bf86d..f3c91a1ca39 100644 --- a/arch/arm/mach-omap2/cm.h +++ b/arch/arm/mach-omap2/cm.h @@ -29,9 +29,9 @@ * These registers appear once per CM module. */ -#define OMAP3430_CM_REVISION OMAP_CM_REGADDR(OCP_MOD, 0x0000) -#define OMAP3430_CM_SYSCONFIG OMAP_CM_REGADDR(OCP_MOD, 0x0010) -#define OMAP3430_CM_POLCTRL OMAP_CM_REGADDR(OCP_MOD, 0x009c) +#define OMAP3430_CM_REVISION OMAP34XX_CM_REGADDR(OCP_MOD, 0x0000) +#define OMAP3430_CM_SYSCONFIG OMAP34XX_CM_REGADDR(OCP_MOD, 0x0010) +#define OMAP3430_CM_POLCTRL OMAP34XX_CM_REGADDR(OCP_MOD, 0x009c) #define OMAP3_CM_CLKOUT_CTRL_OFFSET 0x0070 #define OMAP3430_CM_CLKOUT_CTRL OMAP_CM_REGADDR(OMAP3430_CCR_MOD, 0x0070) -- cgit From 3a6667acf916b3e32be4682196882fc2ed0ec23e Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Mon, 27 Apr 2009 07:50:23 -0700 Subject: OMAP3: PM: Ensure PRCM interrupts are cleared at boot Any pending PRCM interrupts can prevent retention. Ensure they are cleared during boot. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 765cdc0cd7a..cc83dfc39a8 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -613,6 +613,9 @@ static void __init prcm_setup_regs(void) /* Clear any pending PRCM interrupts */ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); + /* Clear any pending PRCM interrupts */ + prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); + omap3_iva_idle(); omap3_d2d_idle(); } -- cgit From 3a07ae30a0bfa93ff2b242acf670c6d8e2de35de Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Mon, 27 Apr 2009 16:14:54 -0700 Subject: OMAP3: PM: Clear pending PRCM reset flags on init Any pending reset flags can prevent retention. Ensure they are all cleared during boot. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 9 +++++++++ 1 file changed, 9 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index cc83dfc39a8..1422e931f57 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -613,6 +613,15 @@ static void __init prcm_setup_regs(void) /* Clear any pending PRCM interrupts */ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); + /* Clear any pending 'reset' flags */ + prm_write_mod_reg(0xffffffff, MPU_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, CORE_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, OMAP3430_PER_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, OMAP3430_EMU_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, OMAP3430_NEON_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, OMAP3430_DSS_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, OMAP3430ES2_USBHOST_MOD, RM_RSTST); + /* Clear any pending PRCM interrupts */ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); -- cgit From 040fed059c34da5115790609f1a038fc9aec88d1 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Tue, 5 May 2009 16:34:25 -0700 Subject: OMAP3: PM: prevent module wakeups from waking IVA2 By default, prevent functional wakeups from inside a module from waking up the IVA2. Let DSP Bridge code handle this when loaded. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 1422e931f57..c813a081c3c 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -613,6 +613,12 @@ static void __init prcm_setup_regs(void) /* Clear any pending PRCM interrupts */ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); + /* Don't attach IVA interrupts */ + prm_write_mod_reg(0, WKUP_MOD, OMAP3430_PM_IVAGRPSEL); + prm_write_mod_reg(0, CORE_MOD, OMAP3430_PM_IVAGRPSEL1); + prm_write_mod_reg(0, CORE_MOD, OMAP3430ES2_PM_IVAGRPSEL3); + prm_write_mod_reg(0, OMAP3430_PER_MOD, OMAP3430_PM_IVAGRPSEL); + /* Clear any pending 'reset' flags */ prm_write_mod_reg(0xffffffff, MPU_MOD, RM_RSTST); prm_write_mod_reg(0xffffffff, CORE_MOD, RM_RSTST); -- cgit From 10f90ed2d727c0f344d910c02c9726d0481d9b00 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Wed, 24 Jun 2009 11:39:18 -0700 Subject: OMAP3: PM: Do not build suspend code if SUSPEND is not enabled Signed-off-by: Jouni Hogander Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index c813a081c3c..528f725722a 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -39,7 +39,9 @@ struct power_state { struct powerdomain *pwrdm; u32 next_state; +#ifdef CONFIG_SUSPEND u32 saved_state; +#endif struct list_head node; }; @@ -293,6 +295,7 @@ out: local_irq_enable(); } +#ifdef CONFIG_SUSPEND static int omap3_pm_prepare(void) { disable_hlt(); @@ -366,6 +369,7 @@ static struct platform_suspend_ops omap_pm_ops = { .finish = omap3_pm_finish, .valid = suspend_valid_only_mem, }; +#endif /* CONFIG_SUSPEND */ /** @@ -710,7 +714,9 @@ static int __init omap3_pm_init(void) _omap_sram_idle = omap_sram_push(omap34xx_cpu_suspend, omap34xx_cpu_suspend_sz); +#ifdef CONFIG_SUSPEND suspend_set_ops(&omap_pm_ops); +#endif /* CONFIG_SUSPEND */ pm_idle = omap3_pm_idle; -- cgit From 4789998a30d845d94a7595076d1392ffd5a9d39e Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Wed, 24 Jun 2009 10:32:03 -0700 Subject: OMAP4: UART: cleanup special case IRQ handling Streamline the OMAP4 special IRQ assignments by putting inside normal init loop instead of having a separate loop. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/serial.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index b094c15bfe4..c82ec95cd79 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -496,10 +496,6 @@ void __init omap_serial_init(void) if (info == NULL) return; - if (cpu_is_omap44xx()) { - for (i = 0; i < OMAP_MAX_NR_PORTS; i++) - serial_platform_data[i].irq += 32; - } for (i = 0; i < OMAP_MAX_NR_PORTS; i++) { struct plat_serial8250_port *p = serial_platform_data + i; @@ -533,6 +529,9 @@ void __init omap_serial_init(void) uart->p = p; list_add(&uart->node, &uart_list); + if (cpu_is_omap44xx()) + p->irq += 32; + omap_uart_enable_clocks(uart); omap_uart_reset(uart); omap_uart_idle_init(uart); -- cgit From 2466211e5debd205fc550d871fe0ab9b9a6d02ed Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Thu, 5 Mar 2009 16:32:23 +0200 Subject: OMAP3: Fixed crash bug with serial + suspend It was possible for an unhandled interrupt to occur if there was incoming serial traffic during wakeup from suspend. This was caused by the code in arch-arm/mach-omap2/serial.c keeping interrupt enabled all the time, but not acking its interrupts. Applies on top of PM branch. Use the PM begin/end hooks to ensure that the "serial idle" interrupts are disabled during the suspend path. Also, since begin/end hooks are now used, use the suspend_state that is passed in the begin hook instead of the enter hook as per the platform_suspend_ops docs. Signed-off-by: Tero Kristo Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 23 +++++++++++++++++++++-- arch/arm/mach-omap2/serial.c | 14 ++++++++++++++ arch/arm/plat-omap/include/mach/serial.h | 1 + 3 files changed, 36 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 528f725722a..b07efb26de1 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -296,6 +296,8 @@ out: } #ifdef CONFIG_SUSPEND +static suspend_state_t suspend_state; + static int omap3_pm_prepare(void) { disable_hlt(); @@ -342,11 +344,11 @@ restore: return ret; } -static int omap3_pm_enter(suspend_state_t state) +static int omap3_pm_enter(suspend_state_t unused) { int ret = 0; - switch (state) { + switch (suspend_state) { case PM_SUSPEND_STANDBY: case PM_SUSPEND_MEM: ret = omap3_pm_suspend(); @@ -363,7 +365,24 @@ static void omap3_pm_finish(void) enable_hlt(); } +/* Hooks to enable / disable UART interrupts during suspend */ +static int omap3_pm_begin(suspend_state_t state) +{ + suspend_state = state; + omap_uart_enable_irqs(0); + return 0; +} + +static void omap3_pm_end(void) +{ + suspend_state = PM_SUSPEND_ON; + omap_uart_enable_irqs(1); + return; +} + static struct platform_suspend_ops omap_pm_ops = { + .begin = omap3_pm_begin, + .end = omap3_pm_end, .prepare = omap3_pm_prepare, .enter = omap3_pm_enter, .finish = omap3_pm_finish, diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index c82ec95cd79..5352d05b42d 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -435,6 +435,20 @@ static void omap_uart_idle_init(struct omap_uart_state *uart) WARN_ON(ret); } +void omap_uart_enable_irqs(int enable) +{ + int ret; + struct omap_uart_state *uart; + + list_for_each_entry(uart, &uart_list, node) { + if (enable) + ret = request_irq(uart->p->irq, omap_uart_interrupt, + IRQF_SHARED, "serial idle", (void *)uart); + else + free_irq(uart->p->irq, (void *)uart); + } +} + static ssize_t sleep_timeout_show(struct kobject *kobj, struct kobj_attribute *attr, char *buf) diff --git a/arch/arm/plat-omap/include/mach/serial.h b/arch/arm/plat-omap/include/mach/serial.h index 13abd02d152..def0529c75e 100644 --- a/arch/arm/plat-omap/include/mach/serial.h +++ b/arch/arm/plat-omap/include/mach/serial.h @@ -59,6 +59,7 @@ extern void omap_uart_check_wakeup(void); extern void omap_uart_prepare_suspend(void); extern void omap_uart_prepare_idle(int num); extern void omap_uart_resume_idle(int num); +extern void omap_uart_enable_irqs(int enable); #endif #endif -- cgit From fd455ea899b5a14a8cdd276e15f3b47696526f92 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Mon, 27 Apr 2009 12:27:36 -0700 Subject: OMAP2/3/4: UART: Allow per-UART disabling wakeup for serial ports This patch causes the OMAP uarts to honor the sysfs power/wakeup file for IOPAD wakeups. Before the OMAP was always woken up from off mode on a rs232 signal change. This patch also creates a different platform device for each serial port so that the wakeup properties can be control per port. By default, IOPAD wakeups are enabled for each UART. To disable, # echo disabled > /sys/devices/platform/serial8250.0/power/wakeup Where serial8250.0 can be replaced by .1, or .2 to control the other ports. Original idea and original patch from Russ Dill Cc: Russ Dill Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/serial.c | 174 ++++++++++++++++++++++++++++--------------- 1 file changed, 116 insertions(+), 58 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index 5352d05b42d..6f35a7e4893 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -54,6 +54,7 @@ struct omap_uart_state { struct plat_serial8250_port *p; struct list_head node; + struct platform_device pdev; #if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM) int context_valid; @@ -68,10 +69,9 @@ struct omap_uart_state { #endif }; -static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS]; static LIST_HEAD(uart_list); -static struct plat_serial8250_port serial_platform_data[] = { +static struct plat_serial8250_port serial_platform_data0[] = { { .membase = IO_ADDRESS(OMAP_UART1_BASE), .mapbase = OMAP_UART1_BASE, @@ -81,6 +81,12 @@ static struct plat_serial8250_port serial_platform_data[] = { .regshift = 2, .uartclk = OMAP24XX_BASE_BAUD * 16, }, { + .flags = 0 + } +}; + +static struct plat_serial8250_port serial_platform_data1[] = { + { .membase = IO_ADDRESS(OMAP_UART2_BASE), .mapbase = OMAP_UART2_BASE, .irq = 73, @@ -89,6 +95,12 @@ static struct plat_serial8250_port serial_platform_data[] = { .regshift = 2, .uartclk = OMAP24XX_BASE_BAUD * 16, }, { + .flags = 0 + } +}; + +static struct plat_serial8250_port serial_platform_data2[] = { + { .membase = IO_ADDRESS(OMAP_UART3_BASE), .mapbase = OMAP_UART3_BASE, .irq = 74, @@ -217,6 +229,40 @@ static inline void omap_uart_disable_clocks(struct omap_uart_state *uart) clk_disable(uart->fck); } +static void omap_uart_enable_wakeup(struct omap_uart_state *uart) +{ + /* Set wake-enable bit */ + if (uart->wk_en && uart->wk_mask) { + u32 v = __raw_readl(uart->wk_en); + v |= uart->wk_mask; + __raw_writel(v, uart->wk_en); + } + + /* Ensure IOPAD wake-enables are set */ + if (cpu_is_omap34xx() && uart->padconf) { + u16 v = omap_ctrl_readw(uart->padconf); + v |= OMAP3_PADCONF_WAKEUPENABLE0; + omap_ctrl_writew(v, uart->padconf); + } +} + +static void omap_uart_disable_wakeup(struct omap_uart_state *uart) +{ + /* Clear wake-enable bit */ + if (uart->wk_en && uart->wk_mask) { + u32 v = __raw_readl(uart->wk_en); + v &= ~uart->wk_mask; + __raw_writel(v, uart->wk_en); + } + + /* Ensure IOPAD wake-enables are cleared */ + if (cpu_is_omap34xx() && uart->padconf) { + u16 v = omap_ctrl_readw(uart->padconf); + v &= ~OMAP3_PADCONF_WAKEUPENABLE0; + omap_ctrl_writew(v, uart->padconf); + } +} + static void omap_uart_smart_idle_enable(struct omap_uart_state *uart, int enable) { @@ -246,6 +292,11 @@ static void omap_uart_block_sleep(struct omap_uart_state *uart) static void omap_uart_allow_sleep(struct omap_uart_state *uart) { + if (device_may_wakeup(&uart->pdev.dev)) + omap_uart_enable_wakeup(uart); + else + omap_uart_disable_wakeup(uart); + if (!uart->clocked) return; @@ -292,7 +343,6 @@ void omap_uart_resume_idle(int num) /* Check for normal UART wakeup */ if (__raw_readl(uart->wk_st) & uart->wk_mask) omap_uart_block_sleep(uart); - return; } } @@ -346,16 +396,13 @@ static irqreturn_t omap_uart_interrupt(int irq, void *dev_id) return IRQ_NONE; } -static u32 sleep_timeout = DEFAULT_TIMEOUT; - static void omap_uart_idle_init(struct omap_uart_state *uart) { - u32 v; struct plat_serial8250_port *p = uart->p; int ret; uart->can_sleep = 0; - uart->timeout = sleep_timeout; + uart->timeout = DEFAULT_TIMEOUT; setup_timer(&uart->timer, omap_uart_idle_timer, (unsigned long) uart); mod_timer(&uart->timer, jiffies + uart->timeout); @@ -413,22 +460,6 @@ static void omap_uart_idle_init(struct omap_uart_state *uart) uart->padconf = 0; } - /* Set wake-enable bit */ - if (uart->wk_en && uart->wk_mask) { - v = __raw_readl(uart->wk_en); - v |= uart->wk_mask; - __raw_writel(v, uart->wk_en); - } - - /* Ensure IOPAD wake-enables are set */ - if (cpu_is_omap34xx() && uart->padconf) { - u16 v; - - v = omap_ctrl_readw(uart->padconf); - v |= OMAP3_PADCONF_WAKEUPENABLE0; - omap_ctrl_writew(v, uart->padconf); - } - p->flags |= UPF_SHARE_IRQ; ret = request_irq(p->irq, omap_uart_interrupt, IRQF_SHARED, "serial idle", (void *)uart); @@ -449,54 +480,81 @@ void omap_uart_enable_irqs(int enable) } } -static ssize_t sleep_timeout_show(struct kobject *kobj, - struct kobj_attribute *attr, +static ssize_t sleep_timeout_show(struct device *dev, + struct device_attribute *attr, char *buf) { - return sprintf(buf, "%u\n", sleep_timeout / HZ); + struct platform_device *pdev = container_of(dev, + struct platform_device, dev); + struct omap_uart_state *uart = container_of(pdev, + struct omap_uart_state, pdev); + + return sprintf(buf, "%u\n", uart->timeout / HZ); } -static ssize_t sleep_timeout_store(struct kobject *kobj, - struct kobj_attribute *attr, +static ssize_t sleep_timeout_store(struct device *dev, + struct device_attribute *attr, const char *buf, size_t n) { - struct omap_uart_state *uart; + struct platform_device *pdev = container_of(dev, + struct platform_device, dev); + struct omap_uart_state *uart = container_of(pdev, + struct omap_uart_state, pdev); unsigned int value; if (sscanf(buf, "%u", &value) != 1) { printk(KERN_ERR "sleep_timeout_store: Invalid value\n"); return -EINVAL; } - sleep_timeout = value * HZ; - list_for_each_entry(uart, &uart_list, node) { - uart->timeout = sleep_timeout; - if (uart->timeout) - mod_timer(&uart->timer, jiffies + uart->timeout); - else - /* A zero value means disable timeout feature */ - omap_uart_block_sleep(uart); - } + + uart->timeout = value * HZ; + if (uart->timeout) + mod_timer(&uart->timer, jiffies + uart->timeout); + else + /* A zero value means disable timeout feature */ + omap_uart_block_sleep(uart); + return n; } -static struct kobj_attribute sleep_timeout_attr = - __ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store); - +DEVICE_ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store); +#define DEV_CREATE_FILE(dev, attr) WARN_ON(device_create_file(dev, attr)) #else static inline void omap_uart_idle_init(struct omap_uart_state *uart) {} +#define DEV_CREATE_FILE(dev, attr) #endif /* CONFIG_PM */ -static struct platform_device serial_device = { - .name = "serial8250", - .id = PLAT8250_DEV_PLATFORM, - .dev = { - .platform_data = serial_platform_data, +static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS] = { + { + .pdev = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM, + .dev = { + .platform_data = serial_platform_data0, + }, + }, + }, { + .pdev = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM1, + .dev = { + .platform_data = serial_platform_data1, + }, + }, + }, { + .pdev = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM2, + .dev = { + .platform_data = serial_platform_data2, + }, + }, }, }; void __init omap_serial_init(void) { - int i, err; + int i; const struct omap_uart_config *info; char name[16]; @@ -512,8 +570,10 @@ void __init omap_serial_init(void) return; for (i = 0; i < OMAP_MAX_NR_PORTS; i++) { - struct plat_serial8250_port *p = serial_platform_data + i; struct omap_uart_state *uart = &omap_uart[i]; + struct platform_device *pdev = &uart->pdev; + struct device *dev = &pdev->dev; + struct plat_serial8250_port *p = dev->platform_data; if (!(info->enabled_uarts & (1 << i))) { p->membase = NULL; @@ -549,15 +609,13 @@ void __init omap_serial_init(void) omap_uart_enable_clocks(uart); omap_uart_reset(uart); omap_uart_idle_init(uart); - } - - err = platform_device_register(&serial_device); - -#ifdef CONFIG_PM - if (!err) - err = sysfs_create_file(&serial_device.dev.kobj, - &sleep_timeout_attr.attr); -#endif + if (WARN_ON(platform_device_register(pdev))) + continue; + if ((cpu_is_omap34xx() && uart->padconf) || + (uart->wk_en && uart->wk_mask)) { + device_init_wakeup(dev, true); + DEV_CREATE_FILE(dev, &dev_attr_sleep_timeout); + } + } } - -- cgit From bcf396c48012a5e4c7ab77be5c40df10d6bdb8ad Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Tue, 30 Jun 2009 21:02:45 -0700 Subject: OMAP2/3/4: UART: allow in-order port traversal Use list_add_tail() when adding discovered UART ports. This is so traversal using list_for_each_entry() will traverse the list in the order they were found. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/serial.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index 6f35a7e4893..a7421a50410 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -601,7 +601,7 @@ void __init omap_serial_init(void) uart->num = i; p->private_data = uart; uart->p = p; - list_add(&uart->node, &uart_list); + list_add_tail(&uart->node, &uart_list); if (cpu_is_omap44xx()) p->irq += 32; -- cgit From 60c45ae1107c4ec47d2c84e5984ea59d02b2863d Mon Sep 17 00:00:00 2001 From: Eero Nurkkala Date: Tue, 23 Jun 2009 12:53:29 +0300 Subject: OMAP: PM: CPUfreq: obey min/max settings of policy Use the min/max settings from CPUfreq policy rather than processor defined min/max settings. Without this patch, it's possible to scale frequency outside the current policy range. Signed-off-by: Eero Nurkkala Signed-off-by: Kevin Hilman --- arch/arm/plat-omap/cpu-omap.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-omap/cpu-omap.c b/arch/arm/plat-omap/cpu-omap.c index 843e8af6406..1868c0d8f9b 100644 --- a/arch/arm/plat-omap/cpu-omap.c +++ b/arch/arm/plat-omap/cpu-omap.c @@ -78,10 +78,10 @@ static int omap_target(struct cpufreq_policy *policy, /* Ensure desired rate is within allowed range. Some govenors * (ondemand) will just pass target_freq=0 to get the minimum. */ - if (target_freq < policy->cpuinfo.min_freq) - target_freq = policy->cpuinfo.min_freq; - if (target_freq > policy->cpuinfo.max_freq) - target_freq = policy->cpuinfo.max_freq; + if (target_freq < policy->min) + target_freq = policy->min; + if (target_freq > policy->max) + target_freq = policy->max; freqs.old = omap_getspeed(0); freqs.new = clk_round_rate(mpu_clk, target_freq * 1000) / 1000; -- cgit From 6c5f80393b107b0c9e2a54b03b65d1880e706655 Mon Sep 17 00:00:00 2001 From: Jouni Hogander Date: Wed, 29 Oct 2008 12:06:04 +0200 Subject: OMAP3: PM: Fix wrong sequence in suspend. Powerdomain previous state is checked after restoring new states in suspend. This patch fixes this problem. Signed-off-by: Jouni Hogander Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index b07efb26de1..488d595d8e4 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -326,7 +326,6 @@ static int omap3_pm_suspend(void) restore: /* Restore next_pwrsts */ list_for_each_entry(pwrst, &pwrst_list, node) { - set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state); state = pwrdm_read_prev_pwrst(pwrst->pwrdm); if (state > pwrst->next_state) { printk(KERN_INFO "Powerdomain (%s) didn't enter " @@ -334,6 +333,7 @@ restore: pwrst->pwrdm->name, pwrst->next_state); ret = -1; } + set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state); } if (ret) printk(KERN_ERR "Could not enter target state in pm_suspend\n"); -- cgit From 55b6019ae29456e0f1e4087546bf4221c48622a0 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Thu, 4 Jun 2009 15:57:10 -0700 Subject: OMAP: GPIO: clear/restore level/edge detect settings on mask/unmask If IRQ triggering is enabled, it can trigger a pending interrupt even for masked interrupts. Any pending GPIO interrupts can prevent the powerdomain from hitting retention. Problem found, reported and additional review and testing by Chunquiu Wang. Tested-by: Chunquiu Wang Signed-off-by: Kevin Hilman --- arch/arm/plat-omap/gpio.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/plat-omap/gpio.c b/arch/arm/plat-omap/gpio.c index 26b387c1242..77bad14633e 100644 --- a/arch/arm/plat-omap/gpio.c +++ b/arch/arm/plat-omap/gpio.c @@ -1189,6 +1189,7 @@ static void gpio_mask_irq(unsigned int irq) struct gpio_bank *bank = get_irq_chip_data(irq); _set_gpio_irqenable(bank, gpio, 0); + _set_gpio_triggering(bank, get_gpio_index(gpio), IRQ_TYPE_NONE); } static void gpio_unmask_irq(unsigned int irq) @@ -1196,6 +1197,11 @@ static void gpio_unmask_irq(unsigned int irq) unsigned int gpio = irq - IH_GPIO_BASE; struct gpio_bank *bank = get_irq_chip_data(irq); unsigned int irq_mask = 1 << get_gpio_index(gpio); + struct irq_desc *desc = irq_to_desc(irq); + u32 trigger = desc->status & IRQ_TYPE_SENSE_MASK; + + if (trigger) + _set_gpio_triggering(bank, get_gpio_index(gpio), trigger); /* For level-triggered GPIOs, the clearing must be done after * the HW source is cleared, thus after the handler has run */ -- cgit From 6fd210a9cc398ecbff7bcdbe220651b73b654f56 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Mon, 20 Jul 2009 09:09:23 -0700 Subject: OMAP3: Overo: add missing pen-down GPIO definition Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/board-overo.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index dff5528fbfb..e26af837510 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -51,6 +51,7 @@ #define OVERO_GPIO_BT_XGATE 15 #define OVERO_GPIO_W2W_NRESET 16 +#define OVERO_GPIO_PENDOWN 114 #define OVERO_GPIO_BT_NRESET 164 #define OVERO_GPIO_USBH_CPEN 168 #define OVERO_GPIO_USBH_NRESET 183 -- cgit From 0a51810aa058a0a4ac76dd6f87f4d10bee774e2e Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Tue, 4 Aug 2009 19:55:56 +0100 Subject: ARM: 5637/1: [KS8695] Don't reference CLOCK_TICK_RATE in drivers Stop referencing CLOCK_TICK_RATE in the KS8695 drivers, rather refer to a KS8695_CLOCK_RATE. Issue pointed out by Russell King on arm-linux-kernel mailing list. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-ks8695/include/mach/hardware.h | 5 +++++ arch/arm/mach-ks8695/include/mach/timex.h | 5 +++-- 2 files changed, 8 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-ks8695/include/mach/hardware.h b/arch/arm/mach-ks8695/include/mach/hardware.h index 1d640d075b7..e0f911d9e02 100644 --- a/arch/arm/mach-ks8695/include/mach/hardware.h +++ b/arch/arm/mach-ks8695/include/mach/hardware.h @@ -16,6 +16,11 @@ #include +/* + * Clocks are derived from MCLK, which is 25Mhz + */ +#define KS8695_CLOCK_RATE 25000000 + /* * Physical RAM address. */ diff --git a/arch/arm/mach-ks8695/include/mach/timex.h b/arch/arm/mach-ks8695/include/mach/timex.h index 4682e350369..10f716371bd 100644 --- a/arch/arm/mach-ks8695/include/mach/timex.h +++ b/arch/arm/mach-ks8695/include/mach/timex.h @@ -14,7 +14,8 @@ #ifndef __ASM_ARCH_TIMEX_H #define __ASM_ARCH_TIMEX_H -/* timers are derived from MCLK, which is 25MHz */ -#define CLOCK_TICK_RATE 25000000 +#include + +#define CLOCK_TICK_RATE KS8695_CLOCK_RATE #endif -- cgit From 65a5053b764a42d33b334ba55810bb5b56eb92df Mon Sep 17 00:00:00 2001 From: Hartley Sweeten Date: Tue, 4 Aug 2009 23:20:45 +0100 Subject: ARM: 5638/1: arch/arm/kernel/signal.c: use correct address space for CRUNCH preserve_crunch_context() calls __copy_to_user() which expects the destination address to be in __user space. setup_sigframe() properly passes the destination address. restore_crunch_context() calls __copy_from_user() which expects the source address to be in __user space. restore_sigframe() properly passes the source address. This fixes {preserve/restore}_crunch_context() to accept the address as __user space and resolves the following sparse warnings: arch/arm/kernel/signal.c:146:31: warning: incorrect type in argument 1 (different address spaces) expected void [noderef] *to got struct crunch_sigframe *frame arch/arm/kernel/signal.c:156:38: warning: incorrect type in argument 2 (different address spaces) expected void const [noderef] *from got struct crunch_sigframe *frame arch/arm/kernel/signal.c:250:48: warning: incorrect type in argument 1 (different address spaces) expected struct crunch_sigframe *frame got struct crunch_sigframe [noderef] * arch/arm/kernel/signal.c:365:49: warning: incorrect type in argument 1 (different address spaces) expected struct crunch_sigframe *frame got struct crunch_sigframe [noderef] * Signed-off-by: H Hartley Sweeten Signed-off-by: Russell King --- arch/arm/kernel/signal.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/kernel/signal.c b/arch/arm/kernel/signal.c index 93bb4247b7e..f6bc5d44278 100644 --- a/arch/arm/kernel/signal.c +++ b/arch/arm/kernel/signal.c @@ -133,7 +133,7 @@ sys_sigaction(int sig, const struct old_sigaction __user *act, } #ifdef CONFIG_CRUNCH -static int preserve_crunch_context(struct crunch_sigframe *frame) +static int preserve_crunch_context(struct crunch_sigframe __user *frame) { char kbuf[sizeof(*frame) + 8]; struct crunch_sigframe *kframe; @@ -146,7 +146,7 @@ static int preserve_crunch_context(struct crunch_sigframe *frame) return __copy_to_user(frame, kframe, sizeof(*frame)); } -static int restore_crunch_context(struct crunch_sigframe *frame) +static int restore_crunch_context(struct crunch_sigframe __user *frame) { char kbuf[sizeof(*frame) + 8]; struct crunch_sigframe *kframe; -- cgit From c0c60c4b9ab45bb02b20796401dd6a90770fd0ee Mon Sep 17 00:00:00 2001 From: Hartley Sweeten Date: Tue, 4 Aug 2009 23:38:06 +0100 Subject: ARM: 5639/1: arm: clkdev.c should include should be included to get the base API prototypes. This fixes the following sparse warnings: arch/arm/common/clkdev.c:65:12: warning: symbol 'clk_get_sys' was not declared. Should it be static? arch/arm/common/clkdev.c:79:12: warning: symbol 'clk_get' was not declared. Should it be static? arch/arm/common/clkdev.c:87:6: warning: symbol 'clk_put' was not declared. Should it be static? Signed-off-by: H Hartley Sweeten Signed-off-by: Russell King --- arch/arm/common/clkdev.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm') diff --git a/arch/arm/common/clkdev.c b/arch/arm/common/clkdev.c index f37afd9422f..aae5bc01acc 100644 --- a/arch/arm/common/clkdev.c +++ b/arch/arm/common/clkdev.c @@ -17,6 +17,7 @@ #include #include #include +#include #include #include -- cgit From e8e2ff462dd92693f29eb848f42d3eb720390d59 Mon Sep 17 00:00:00 2001 From: "Gupta, Ajay Kumar" Date: Wed, 29 Jul 2009 11:58:57 +0530 Subject: USB: musb: fix the nop registration for OMAP3EVM OMAP3EVM uses ISP1504 phy which doesn't require any programming and thus has to use NOP otg transceiver. Cleanups being done: - Remove unwanted code in usb-musb.c file - Register NOP in OMAP3EVM board file using usb_nop_xceiv_register(). - Select NOP_USB_XCEIV for OMAP3EVM boards. - Don't enable TWL4030_USB in omap3_evm_defconfig Signed-off-by: Ajay Kumar Gupta Signed-off-by: Eino-Ville Talvala Acked-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- arch/arm/configs/omap3_evm_defconfig | 2 +- arch/arm/mach-omap2/board-omap3evm.c | 5 +++++ arch/arm/mach-omap2/usb-musb.c | 21 --------------------- 3 files changed, 6 insertions(+), 22 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/configs/omap3_evm_defconfig b/arch/arm/configs/omap3_evm_defconfig index 28be17fbc15..d5ff4776cd0 100644 --- a/arch/arm/configs/omap3_evm_defconfig +++ b/arch/arm/configs/omap3_evm_defconfig @@ -1107,7 +1107,7 @@ CONFIG_USB_ZERO=m CONFIG_USB_OTG_UTILS=y # CONFIG_USB_GPIO_VBUS is not set # CONFIG_ISP1301_OMAP is not set -CONFIG_TWL4030_USB=y +# CONFIG_TWL4030_USB is not set # CONFIG_NOP_USB_XCEIV is not set CONFIG_MMC=y # CONFIG_MMC_DEBUG is not set diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index d3cc145814d..cf3dd771a67 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -25,6 +25,7 @@ #include #include #include +#include #include #include @@ -307,6 +308,10 @@ static void __init omap3_evm_init(void) ARRAY_SIZE(omap3evm_spi_board_info)); omap_serial_init(); +#ifdef CONFIG_NOP_USB_XCEIV + /* OMAP3EVM uses ISP1504 phy and so register nop transceiver */ + usb_nop_xceiv_register(); +#endif usb_musb_init(); ads7846_dev_init(); } diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c index d85296dc896..739e59e8025 100644 --- a/arch/arm/mach-omap2/usb-musb.c +++ b/arch/arm/mach-omap2/usb-musb.c @@ -155,20 +155,6 @@ static struct platform_device musb_device = { .resource = musb_resources, }; -#ifdef CONFIG_NOP_USB_XCEIV -static u64 nop_xceiv_dmamask = DMA_BIT_MASK(32); - -static struct platform_device nop_xceiv_device = { - .name = "nop_usb_xceiv", - .id = -1, - .dev = { - .dma_mask = &nop_xceiv_dmamask, - .coherent_dma_mask = DMA_BIT_MASK(32), - .platform_data = NULL, - }, -}; -#endif - void __init usb_musb_init(void) { if (cpu_is_omap243x()) @@ -183,13 +169,6 @@ void __init usb_musb_init(void) */ musb_plat.clock = "ick"; -#ifdef CONFIG_NOP_USB_XCEIV - if (platform_device_register(&nop_xceiv_device) < 0) { - printk(KERN_ERR "Unable to register NOP-XCEIV device\n"); - return; - } -#endif - if (platform_device_register(&musb_device) < 0) { printk(KERN_ERR "Unable to register HS-USB (MUSB) device\n"); return; -- cgit From cd92204924fafbd5c7241dfd12ca3176d542e0c5 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 10 Aug 2009 14:49:50 +0300 Subject: OMAP: Fix testing of cpu defines for mach-omap1 There's no need to keep these defines limited in the ifdef block for mach-omap2. It will just cause problems testing for the CPU revision in the common code, like the next patch does for the DMA errata. Signed-off-by: Tony Lindgren --- arch/arm/plat-omap/include/mach/cpu.h | 5 ----- 1 file changed, 5 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-omap/include/mach/cpu.h b/arch/arm/plat-omap/include/mach/cpu.h index 285eaa3a827..11e73d9e892 100644 --- a/arch/arm/plat-omap/include/mach/cpu.h +++ b/arch/arm/plat-omap/include/mach/cpu.h @@ -378,9 +378,6 @@ IS_OMAP_TYPE(3430, 0x3430) #define cpu_class_is_omap2() (cpu_is_omap24xx() || cpu_is_omap34xx() || \ cpu_is_omap44xx()) -#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) || \ - defined(CONFIG_ARCH_OMAP4) - /* Various silicon revisions for omap2 */ #define OMAP242X_CLASS 0x24200024 #define OMAP2420_REV_ES1_0 0x24200024 @@ -436,5 +433,3 @@ IS_OMAP_TYPE(3430, 0x3430) int omap_chip_is(struct omap_chip_id oci); void omap2_check_revision(void); - -#endif /* defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) */ -- cgit From 284119c48f4a0c469b3e0237b500e536b4bc7b6f Mon Sep 17 00:00:00 2001 From: Vikram Pandita Date: Mon, 10 Aug 2009 14:49:50 +0300 Subject: OMAP2/3: DMA errata correction This errata is valid for: OMAP2420 Errata 1.85 Impacts all 2420 ES rev OMAP2430 Errata 1.10 Impacts only ES1.0 Description: DMA may hang when several channels are used in parallel OMAP3430: Not impacted, so remove the errata fix for omap3 Fixed issue reported on cpu_is_omap24xx check reported by Nishant Kamat Signed-off-by: Vikram Pandita Reviewed-by: Nishant Kamat Signed-off-by: Tony Lindgren --- arch/arm/plat-omap/dma.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-omap/dma.c b/arch/arm/plat-omap/dma.c index 7677a4a1cef..e3ac94f0900 100644 --- a/arch/arm/plat-omap/dma.c +++ b/arch/arm/plat-omap/dma.c @@ -946,7 +946,9 @@ void omap_start_dma(int lch) cur_lch = next_lch; } while (next_lch != -1); - } else if (cpu_class_is_omap2()) { + } else if (cpu_is_omap242x() || + (cpu_is_omap243x() && omap_type() <= OMAP2430_REV_ES1_0)) { + /* Errata: Need to write lch even if not using chaining */ dma_write(lch, CLNK_CTRL(lch)); } -- cgit From 370bc1fdefb8a30018d98aca2fdfd6b6701082e7 Mon Sep 17 00:00:00 2001 From: Janboe Ye Date: Mon, 10 Aug 2009 14:49:50 +0300 Subject: OMAP3: Fix omap3 sram virtual addres overlap vmalloc space after increasing vmalloc size commit e85c205ac1427f2405021a36f083280ff0d0a35e increase vmalloc size. vmalloc space will overlap with OMAP3 sram virtual address. Signed-off-by: Li Hong Mei Signed-off-by: Janboe Ye Reviewed-by: Paul Walmsley --- arch/arm/plat-omap/sram.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c index 4ea73804d21..2890b11f238 100644 --- a/arch/arm/plat-omap/sram.c +++ b/arch/arm/plat-omap/sram.c @@ -44,9 +44,9 @@ #define OMAP2_SRAM_VA 0xe3000000 #define OMAP2_SRAM_PUB_VA (OMAP2_SRAM_VA + 0x800) #define OMAP3_SRAM_PA 0x40200000 -#define OMAP3_SRAM_VA 0xd7000000 +#define OMAP3_SRAM_VA 0xe3000000 #define OMAP3_SRAM_PUB_PA 0x40208000 -#define OMAP3_SRAM_PUB_VA 0xd7008000 +#define OMAP3_SRAM_PUB_VA (OMAP3_SRAM_VA + 0x8000) #define OMAP4_SRAM_PA 0x40200000 /*0x402f0000*/ #define OMAP4_SRAM_VA 0xd7000000 /*0xd70f0000*/ -- cgit From 5032902c331acc71956e47abd90d090181c5ef4a Mon Sep 17 00:00:00 2001 From: Sergio Aguirre Date: Mon, 10 Aug 2009 14:49:50 +0300 Subject: OMAP3: Overo: Fix smsc911x platform device resource value Fixes a wrong setting of resource parameter list in SMSC911x platform driver data structure for Overo case. This fixes folowing warning when compiling for Overo board: warning: initialization from incompatible pointer type Introduced since commit id: commit 172ef275444efa12d834fb9d1b1acdac92db47f7 Author: Steve Sakoman Date: Mon Feb 2 06:27:49 2009 +0000 ARM: Add SMSC911X support to Overo platform (V2) Signed-off-by: Sergio Aguirre Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-overo.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index dff5528fbfb..fec1bb19b9f 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -146,7 +146,7 @@ static struct platform_device overo_smsc911x_device = { .name = "smsc911x", .id = -1, .num_resources = ARRAY_SIZE(overo_smsc911x_resources), - .resource = &overo_smsc911x_resources, + .resource = overo_smsc911x_resources, .dev = { .platform_data = &overo_smsc911x_config, }, -- cgit From dfc27b34496923b5f552eb9cdf20468045114ada Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Mon, 10 Aug 2009 14:49:51 +0300 Subject: OMAP3: RX51: Define TWL4030 USB transceiver in board file Add OTG transceiver to RX51 platform data to prevent kernel NULL pointer dereference during MUSB initialisation. Signed-off-by: Roger Quadros Signed-off-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-rx51-peripherals.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c index 9a0bf6744a0..56d931a425f 100644 --- a/arch/arm/mach-omap2/board-rx51-peripherals.c +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c @@ -278,6 +278,10 @@ static struct twl4030_gpio_platform_data rx51_gpio_data = { .setup = rx51_twlgpio_setup, }; +static struct twl4030_usb_data rx51_usb_data = { + .usb_mode = T2_USB_MODE_ULPI, +}; + static struct twl4030_platform_data rx51_twldata = { .irq_base = TWL4030_IRQ_BASE, .irq_end = TWL4030_IRQ_END, @@ -286,6 +290,7 @@ static struct twl4030_platform_data rx51_twldata = { .gpio = &rx51_gpio_data, .keypad = &rx51_kp_data, .madc = &rx51_madc_data, + .usb = &rx51_usb_data, .vaux1 = &rx51_vaux1, .vaux2 = &rx51_vaux2, -- cgit From 22833044fbe2764d44ae03f58508e671652ca186 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Mon, 10 Aug 2009 14:49:51 +0300 Subject: OMAP2/3: mmc-twl4030: Free up MMC regulators while cleaning up twl_mmc_cleanup() must free up the regulators that were allocated by twl_mmc_late_init(). This eliminates the below error when 'omap_hsmmc' module is repeatedly loaded and unloaded. "sysfs: cannot create duplicate filename '/devices/platform /mmci-omap-hs.0/microamps_requested_vmmc'" Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/mmc-twl4030.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/mmc-twl4030.c b/arch/arm/mach-omap2/mmc-twl4030.c index 1541fd4c8d0..3c04c2f1b23 100644 --- a/arch/arm/mach-omap2/mmc-twl4030.c +++ b/arch/arm/mach-omap2/mmc-twl4030.c @@ -119,6 +119,7 @@ static int twl_mmc_late_init(struct device *dev) if (i != 0) break; ret = PTR_ERR(reg); + hsmmc[i].vcc = NULL; goto err; } hsmmc[i].vcc = reg; @@ -165,8 +166,13 @@ done: static void twl_mmc_cleanup(struct device *dev) { struct omap_mmc_platform_data *mmc = dev->platform_data; + int i; gpio_free(mmc->slots[0].switch_pin); + for(i = 0; i < ARRAY_SIZE(hsmmc); i++) { + regulator_put(hsmmc[i].vcc); + regulator_put(hsmmc[i].vcc_aux); + } } #ifdef CONFIG_PM -- cgit From 4177662ec9f5e50b69ef074369fdb429dd48d97e Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Mon, 10 Aug 2009 14:49:52 +0300 Subject: OMAP3: RX51: Updated rx51_defconfig Added REGULATOR, MMC and updated default CMDLINE so RX51 now boots. Note that the regulator code should be moved from mmc-twl4030.c to omap_hsmmc.c so it can be a module. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/configs/rx51_defconfig | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/configs/rx51_defconfig b/arch/arm/configs/rx51_defconfig index eb2cb31825c..f238df66efd 100644 --- a/arch/arm/configs/rx51_defconfig +++ b/arch/arm/configs/rx51_defconfig @@ -282,7 +282,7 @@ CONFIG_ALIGNMENT_TRAP=y # CONFIG_ZBOOT_ROM_TEXT=0x0 CONFIG_ZBOOT_ROM_BSS=0x0 -CONFIG_CMDLINE="init=/sbin/preinit ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs rootflags=bulk_read,no_chk_data_crc rw console=ttyMTD,log console=tty0" +CONFIG_CMDLINE="init=/sbin/preinit ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs rootflags=bulk_read,no_chk_data_crc rw console=ttyMTD,log console=tty0 console=ttyS2,115200n8" # CONFIG_XIP_KERNEL is not set # CONFIG_KEXEC is not set @@ -1354,7 +1354,7 @@ CONFIG_USB_OTG_UTILS=y # CONFIG_USB_GPIO_VBUS is not set # CONFIG_ISP1301_OMAP is not set CONFIG_TWL4030_USB=y -CONFIG_MMC=m +CONFIG_MMC=y # CONFIG_MMC_DEBUG is not set # CONFIG_MMC_UNSAFE_RESUME is not set @@ -1449,7 +1449,8 @@ CONFIG_RTC_DRV_TWL4030=m # on-CPU RTC drivers # # CONFIG_DMADEVICES is not set -# CONFIG_REGULATOR is not set +CONFIG_REGULATOR=y +CONFIG_REGULATOR_TWL4030=y # CONFIG_UIO is not set # CONFIG_STAGING is not set -- cgit From dee2b904a1f93c275a015b67cd693038d74b18e8 Mon Sep 17 00:00:00 2001 From: Mikael Pettersson Date: Sun, 9 Aug 2009 21:21:57 +0200 Subject: IXP4xx: Fix IO_SPACE_LIMIT for 2.6.31-rc core PCI changes MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit 2.6.31-rc kernels don't boot on my ixp4xx box (ds101), because the libata driver doesn't find the PCI IDE controller any more. 2.6.30 was fine. I traced this to a PCI update (1f82de10d6b1d845155363c895c552e61b36b51a) in 2.6.30-git19. Diffing the kernel boot logs from 2.6.30-git18 and 2.6.30-git19 illustrates the breakage: > --- dmesg-2.6.30-git18 2009-08-04 01:45:22.000000000 +0200 > +++ dmesg-2.6.30-git19 2009-08-04 01:45:46.000000000 +0200 > @@ -26,6 +26,13 @@ > pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot > pci 0000:00:02.2: PME# disabled > PCI: bus0: Fast back to back transfers disabled > +pci 0000:00:01.0: BAR 0: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:01.0: BAR 1: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:01.0: BAR 2: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:01.0: BAR 3: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:01.0: BAR 4: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:02.0: BAR 4: can't allocate I/O resource [0x10000-0xffff] > +pci 0000:00:02.1: BAR 4: can't allocate I/O resource [0x10000-0xffff] > bio: create slab at 0 > SCSI subsystem initialized > NET: Registered protocol family 2 > @@ -44,11 +51,7 @@ > console [ttyS0] enabled > serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale > Driver 'sd' needs updating - please use bus_type methods > -PCI: enabling device 0000:00:01.0 (0140 -> 0141) > -scsi0 : pata_artop > -scsi1 : pata_artop > -ata1: PATA max UDMA/100 cmd 0x1050 ctl 0x1060 bmdma 0x1040 irq 28 > -ata2: PATA max UDMA/100 cmd 0x1058 ctl 0x1064 bmdma 0x1048 irq 28 > +pata_artop 0000:00:01.0: no available native port > Using configured DiskOnChip probe address 0x50000000 > DiskOnChip found at 0x50000000 > NAND device: Manufacturer ID: 0x98, Chip ID: 0x73 (Toshiba NAND 16MiB 3,3V 8-bit) The specific change in 1f82de10d6b1d845155363c895c552e61b36b51a responsible for this failure turned out to be the following: > --- a/drivers/pci/probe.c > +++ b/drivers/pci/probe.c > @@ -193,7 +193,7 @@ int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type, > res->flags |= pci_calc_resource_flags(l) | IORESOURCE_SIZEALIGN; > if (type == pci_bar_io) { > l &= PCI_BASE_ADDRESS_IO_MASK; > - mask = PCI_BASE_ADDRESS_IO_MASK & 0xffff; > + mask = PCI_BASE_ADDRESS_IO_MASK & IO_SPACE_LIMIT; > } else { > l &= PCI_BASE_ADDRESS_MEM_MASK; > mask = (u32)PCI_BASE_ADDRESS_MEM_MASK; Every arch except arm's ixp4xx defines IO_SPACE_LIMIT as an all-bits-one bitmask, typically -1UL but sometimes only a 16-bit 0x0000ffff. But ixp4xx defines it as 0xffff0000, which is now causing the PCI failures. Russell King noted that ixp4xx has 64KB PCI IO space, so IO_SPACE_LIMIT should be 0x0000ffff. This patch makes that change, which fixes the PCI failures on my ixp4xx box. Signed-off-by: Mikael Pettersson Signed-off-by: Krzysztof Hałasa --- arch/arm/mach-ixp4xx/include/mach/io.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-ixp4xx/include/mach/io.h b/arch/arm/mach-ixp4xx/include/mach/io.h index ce63048d45e..8a947d42a6f 100644 --- a/arch/arm/mach-ixp4xx/include/mach/io.h +++ b/arch/arm/mach-ixp4xx/include/mach/io.h @@ -17,7 +17,7 @@ #include -#define IO_SPACE_LIMIT 0xffff0000 +#define IO_SPACE_LIMIT 0x0000ffff extern int (*ixp4xx_pci_read)(u32 addr, u32 cmd, u32* data); extern int ixp4xx_pci_write(u32 addr, u32 cmd, u32 data); -- cgit From 48ec45e725aa385d72bced73b267dfaf13351876 Mon Sep 17 00:00:00 2001 From: Davide Rizzo Date: Thu, 13 Aug 2009 11:53:53 +0200 Subject: ARM: S3C24XX: Fix clkout mpx error Bug correction: CLK Outputs cannot have XTAL as parent Signed-off-by: Davide Rizzo [ben-linux@fluff.org: updated patch subject] Signed-off-by: Ben Dooks --- arch/arm/plat-s3c24xx/clock-dclk.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-s3c24xx/clock-dclk.c b/arch/arm/plat-s3c24xx/clock-dclk.c index 5b75a797b5a..0afb217a775 100644 --- a/arch/arm/plat-s3c24xx/clock-dclk.c +++ b/arch/arm/plat-s3c24xx/clock-dclk.c @@ -129,7 +129,7 @@ static int s3c24xx_clkout_setparent(struct clk *clk, struct clk *parent) /* calculate the MISCCR setting for the clock */ - if (parent == &clk_xtal) + if (parent == &clk_mpll) source = S3C2410_MISCCR_CLK0_MPLL; else if (parent == &clk_upll) source = S3C2410_MISCCR_CLK0_UPLL; -- cgit From 563abb4be1a79e7b64784d43beb9d0cacb1bad6f Mon Sep 17 00:00:00 2001 From: Valentin Longchamp Date: Tue, 11 Aug 2009 17:29:21 +0200 Subject: mx31moboard: invert sdhc ro signal sense Small confusion with our hardware engineer, the WP signal (RO) is active low on our boards, the signal has to inverted. This is a pretty straightforward patch, it could even go to -rc, but if not, then push it for 2.6.32. Signed-off-by: Valentin Longchamp Signed-off-by: Sascha Hauer --- arch/arm/mach-mx3/mx31moboard-devboard.c | 2 +- arch/arm/mach-mx3/mx31moboard-marxbot.c | 2 +- arch/arm/mach-mx3/mx31moboard.c | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-mx3/mx31moboard-devboard.c b/arch/arm/mach-mx3/mx31moboard-devboard.c index 4704405165a..b48581e7ded 100644 --- a/arch/arm/mach-mx3/mx31moboard-devboard.c +++ b/arch/arm/mach-mx3/mx31moboard-devboard.c @@ -63,7 +63,7 @@ static struct imxuart_platform_data uart_pdata = { static int devboard_sdhc2_get_ro(struct device *dev) { - return gpio_get_value(SDHC2_WP); + return !gpio_get_value(SDHC2_WP); } static int devboard_sdhc2_init(struct device *dev, irq_handler_t detect_irq, diff --git a/arch/arm/mach-mx3/mx31moboard-marxbot.c b/arch/arm/mach-mx3/mx31moboard-marxbot.c index 641c3d6153a..901fb0166c0 100644 --- a/arch/arm/mach-mx3/mx31moboard-marxbot.c +++ b/arch/arm/mach-mx3/mx31moboard-marxbot.c @@ -67,7 +67,7 @@ static unsigned int marxbot_pins[] = { static int marxbot_sdhc2_get_ro(struct device *dev) { - return gpio_get_value(SDHC2_WP); + return !gpio_get_value(SDHC2_WP); } static int marxbot_sdhc2_init(struct device *dev, irq_handler_t detect_irq, diff --git a/arch/arm/mach-mx3/mx31moboard.c b/arch/arm/mach-mx3/mx31moboard.c index a17f2e41160..2a2da4739ec 100644 --- a/arch/arm/mach-mx3/mx31moboard.c +++ b/arch/arm/mach-mx3/mx31moboard.c @@ -94,7 +94,7 @@ static struct imxi2c_platform_data moboard_i2c1_pdata = { static int moboard_sdhc1_get_ro(struct device *dev) { - return gpio_get_value(SDHC1_WP); + return !gpio_get_value(SDHC1_WP); } static int moboard_sdhc1_init(struct device *dev, irq_handler_t detect_irq, -- cgit From dde5828f56cb2c1aa70365c476e6830482127258 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sat, 15 Aug 2009 12:36:00 +0100 Subject: ARM: Fix broken highmem support Currently, highmem is selectable, and you can request an increased vmalloc area. However, none of this has any effect on the memory layout since a patch in the highmem series was accidentally dropped. Moreover, even if you did want highmem, all memory would still be registered as lowmem, possibly resulting in overflow of the available virtual mapping space. The highmem boundary is determined by the highest allowed beginning of the vmalloc area, which depends on its configurable minimum size (see commit 60296c71f6c5063e3c1f1d2619ca0b60940162e7 for details on this). We should create mappings and initialize bootmem only for low memory, while the zone allocator must still be told about highmem. Currently, memory nodes which are completely located in high memory are not supported. This is not a huge limitation since systems relying on highmem support are unlikely to have discontiguous memory with large holes. [ A similar patch was meant to be merged before commit 5f0fbf9ecaf3 and be available in Linux v2.6.30, however some git rebase screw-up of mine dropped the first commit of the series, and that goofage escaped testing somehow as well. -- Nico ] Signed-off-by: Russell King Reviewed-by: Nicolas Pitre --- arch/arm/include/asm/setup.h | 3 +- arch/arm/mm/init.c | 118 ++++++++++++++++++++++++++----------------- arch/arm/mm/mmu.c | 9 +++- 3 files changed, 83 insertions(+), 47 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/include/asm/setup.h b/arch/arm/include/asm/setup.h index ee1304f22f9..5ccce0a9b03 100644 --- a/arch/arm/include/asm/setup.h +++ b/arch/arm/include/asm/setup.h @@ -201,7 +201,8 @@ static struct tagtable __tagtable_##fn __tag = { tag, fn } struct membank { unsigned long start; unsigned long size; - int node; + unsigned short node; + unsigned short highmem; }; struct meminfo { diff --git a/arch/arm/mm/init.c b/arch/arm/mm/init.c index 8277802ec85..3a7279c1ce5 100644 --- a/arch/arm/mm/init.c +++ b/arch/arm/mm/init.c @@ -120,6 +120,32 @@ void show_mem(void) printk("%d pages swap cached\n", cached); } +static void __init find_node_limits(int node, struct meminfo *mi, + unsigned long *min, unsigned long *max_low, unsigned long *max_high) +{ + int i; + + *min = -1UL; + *max_low = *max_high = 0; + + for_each_nodebank(i, mi, node) { + struct membank *bank = &mi->bank[i]; + unsigned long start, end; + + start = bank_pfn_start(bank); + end = bank_pfn_end(bank); + + if (*min > start) + *min = start; + if (*max_high < end) + *max_high = end; + if (bank->highmem) + continue; + if (*max_low < end) + *max_low = end; + } +} + /* * FIXME: We really want to avoid allocating the bootmap bitmap * over the top of the initrd. Hopefully, this is located towards @@ -210,40 +236,24 @@ static inline void map_memory_bank(struct membank *bank) #endif } -static unsigned long __init bootmem_init_node(int node, struct meminfo *mi) +static void __init bootmem_init_node(int node, struct meminfo *mi, + unsigned long start_pfn, unsigned long end_pfn) { - unsigned long start_pfn, end_pfn, boot_pfn; + unsigned long boot_pfn; unsigned int boot_pages; pg_data_t *pgdat; int i; - start_pfn = -1UL; - end_pfn = 0; - /* - * Calculate the pfn range, and map the memory banks for this node. + * Map the memory banks for this node. */ for_each_nodebank(i, mi, node) { struct membank *bank = &mi->bank[i]; - unsigned long start, end; - start = bank_pfn_start(bank); - end = bank_pfn_end(bank); - - if (start_pfn > start) - start_pfn = start; - if (end_pfn < end) - end_pfn = end; - - map_memory_bank(bank); + if (!bank->highmem) + map_memory_bank(bank); } - /* - * If there is no memory in this node, ignore it. - */ - if (end_pfn == 0) - return end_pfn; - /* * Allocate the bootmem bitmap page. */ @@ -260,7 +270,8 @@ static unsigned long __init bootmem_init_node(int node, struct meminfo *mi) for_each_nodebank(i, mi, node) { struct membank *bank = &mi->bank[i]; - free_bootmem_node(pgdat, bank_phys_start(bank), bank_phys_size(bank)); + if (!bank->highmem) + free_bootmem_node(pgdat, bank_phys_start(bank), bank_phys_size(bank)); memory_present(node, bank_pfn_start(bank), bank_pfn_end(bank)); } @@ -269,8 +280,6 @@ static unsigned long __init bootmem_init_node(int node, struct meminfo *mi) */ reserve_bootmem_node(pgdat, boot_pfn << PAGE_SHIFT, boot_pages << PAGE_SHIFT, BOOTMEM_DEFAULT); - - return end_pfn; } static void __init bootmem_reserve_initrd(int node) @@ -297,33 +306,39 @@ static void __init bootmem_reserve_initrd(int node) static void __init bootmem_free_node(int node, struct meminfo *mi) { unsigned long zone_size[MAX_NR_ZONES], zhole_size[MAX_NR_ZONES]; - unsigned long start_pfn, end_pfn; - pg_data_t *pgdat = NODE_DATA(node); + unsigned long min, max_low, max_high; int i; - start_pfn = pgdat->bdata->node_min_pfn; - end_pfn = pgdat->bdata->node_low_pfn; + find_node_limits(node, mi, &min, &max_low, &max_high); /* * initialise the zones within this node. */ memset(zone_size, 0, sizeof(zone_size)); - memset(zhole_size, 0, sizeof(zhole_size)); /* * The size of this node has already been determined. If we need * to do anything fancy with the allocation of this memory to the * zones, now is the time to do it. */ - zone_size[0] = end_pfn - start_pfn; + zone_size[0] = max_low - min; +#ifdef CONFIG_HIGHMEM + zone_size[ZONE_HIGHMEM] = max_high - max_low; +#endif /* * For each bank in this node, calculate the size of the holes. * holes = node_size - sum(bank_sizes_in_node) */ - zhole_size[0] = zone_size[0]; - for_each_nodebank(i, mi, node) - zhole_size[0] -= bank_pfn_size(&mi->bank[i]); + memcpy(zhole_size, zone_size, sizeof(zhole_size)); + for_each_nodebank(i, mi, node) { + int idx = 0; +#ifdef CONFIG_HIGHMEM + if (mi->bank[i].highmem) + idx = ZONE_HIGHMEM; +#endif + zhole_size[idx] -= bank_pfn_size(&mi->bank[i]); + } /* * Adjust the sizes according to any special requirements for @@ -331,13 +346,13 @@ static void __init bootmem_free_node(int node, struct meminfo *mi) */ arch_adjust_zones(node, zone_size, zhole_size); - free_area_init_node(node, zone_size, start_pfn, zhole_size); + free_area_init_node(node, zone_size, min, zhole_size); } void __init bootmem_init(void) { struct meminfo *mi = &meminfo; - unsigned long memend_pfn = 0; + unsigned long min, max_low, max_high; int node, initrd_node; /* @@ -345,11 +360,29 @@ void __init bootmem_init(void) */ initrd_node = check_initrd(mi); + max_low = max_high = 0; + /* * Run through each node initialising the bootmem allocator. */ for_each_node(node) { - unsigned long end_pfn = bootmem_init_node(node, mi); + unsigned long node_low, node_high; + + find_node_limits(node, mi, &min, &node_low, &node_high); + + if (node_low > max_low) + max_low = node_low; + if (node_high > max_high) + max_high = node_high; + + /* + * If there is no memory in this node, ignore it. + * (We can't have nodes which have no lowmem) + */ + if (node_low == 0) + continue; + + bootmem_init_node(node, mi, min, node_low); /* * Reserve any special node zero regions. @@ -362,12 +395,6 @@ void __init bootmem_init(void) */ if (node == initrd_node) bootmem_reserve_initrd(node); - - /* - * Remember the highest memory PFN. - */ - if (end_pfn > memend_pfn) - memend_pfn = end_pfn; } /* @@ -383,7 +410,7 @@ void __init bootmem_init(void) for_each_node(node) bootmem_free_node(node, mi); - high_memory = __va((memend_pfn << PAGE_SHIFT) - 1) + 1; + high_memory = __va((max_low << PAGE_SHIFT) - 1) + 1; /* * This doesn't seem to be used by the Linux memory manager any @@ -393,7 +420,8 @@ void __init bootmem_init(void) * Note: max_low_pfn and max_pfn reflect the number of _pages_ in * the system, not the maximum PFN. */ - max_pfn = max_low_pfn = memend_pfn - PHYS_PFN_OFFSET; + max_low_pfn = max_low - PHYS_PFN_OFFSET; + max_pfn = max_high - PHYS_PFN_OFFSET; } static inline int free_area(unsigned long pfn, unsigned long end, char *s) diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c index 4722582b17b..4426ee67cec 100644 --- a/arch/arm/mm/mmu.c +++ b/arch/arm/mm/mmu.c @@ -687,13 +687,19 @@ __early_param("vmalloc=", early_vmalloc); static void __init sanity_check_meminfo(void) { - int i, j; + int i, j, highmem = 0; for (i = 0, j = 0; i < meminfo.nr_banks; i++) { struct membank *bank = &meminfo.bank[j]; *bank = meminfo.bank[i]; #ifdef CONFIG_HIGHMEM + if (__va(bank->start) > VMALLOC_MIN || + __va(bank->start) < (void *)PAGE_OFFSET) + highmem = 1; + + bank->highmem = highmem; + /* * Split those memory banks which are partially overlapping * the vmalloc area greatly simplifying things later. @@ -714,6 +720,7 @@ static void __init sanity_check_meminfo(void) i++; bank[1].size -= VMALLOC_MIN - __va(bank->start); bank[1].start = __pa(VMALLOC_MIN - 1) + 1; + bank[1].highmem = highmem = 1; j++; } bank->size = VMALLOC_MIN - __va(bank->start); -- cgit From a2bb9f4d6a5a589b481595207ac3588cc08d1b60 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Thu, 13 Aug 2009 21:57:22 +0100 Subject: ARM: 5673/1: U300 fix initsection compile warning The u300_init_check_chip() function was not properly tagged with the __init macro and provided a initsection mismatch on compilation. Signed-off-by: Linus Walleij Signed-off-by: Russell King --- arch/arm/mach-u300/core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c index 7936085dd75..2e9b8ccd8ec 100644 --- a/arch/arm/mach-u300/core.c +++ b/arch/arm/mach-u300/core.c @@ -510,7 +510,7 @@ static struct db_chip db_chips[] __initdata = { } }; -static void u300_init_check_chip(void) +static void __init u300_init_check_chip(void) { u16 val; -- cgit From 3e475f579e56caf57cadc0cc995c152f9da641a9 Mon Sep 17 00:00:00 2001 From: Martin Michlmayr Date: Mon, 17 Aug 2009 23:34:10 -1000 Subject: [ARM] Kirkwood: __init requires linux/init.h MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Include linux/init.h for __init to fix this error: CC [M] drivers/net/wireless/wl12xx/boot.o In file included from arch/arm/mach-kirkwood/include/mach/gpio.h:13, from arch/arm/include/asm/gpio.h:5, from include/linux/gpio.h:7, from drivers/net/wireless/wl12xx/boot.c:24: arch/arm/plat-orion/include/plat/gpio.h:32: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘orion_gpio_init’ make[6]: *** [drivers/net/wireless/wl12xx/boot.o] Error 1 make[5]: *** [drivers/net/wireless/wl12xx] Error 2 Signed-off-by: Martin Michlmayr Signed-off-by: Nicolas Pitre --- arch/arm/plat-orion/include/plat/gpio.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/plat-orion/include/plat/gpio.h b/arch/arm/plat-orion/include/plat/gpio.h index 9646a94ed3d..07c430fdc9e 100644 --- a/arch/arm/plat-orion/include/plat/gpio.h +++ b/arch/arm/plat-orion/include/plat/gpio.h @@ -11,6 +11,8 @@ #ifndef __PLAT_GPIO_H #define __PLAT_GPIO_H +#include + /* * GENERIC_GPIO primitives. */ -- cgit From c55bf102b675c94edef006ce487d909669221d90 Mon Sep 17 00:00:00 2001 From: John Holland Date: Wed, 19 Aug 2009 13:24:03 -1000 Subject: [ARM] Kirkwood: enable eSATA on QNAP TS-219P Initialize PCI/PCIe on the QNAP TS-119, TS-219 and TS-219P hardware allowing the use of the discrete eSATA controller connected to the PCIe bus in the TS-219P. Signed-off-by: John Holland Tested-by: Thomas Reitmayr Signed-off-by: Martin Michlmayr Signed-off-by: Nicolas Pitre --- arch/arm/configs/kirkwood_defconfig | 2 +- arch/arm/mach-kirkwood/ts219-setup.c | 9 +++++++++ 2 files changed, 10 insertions(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig index 0a1abb978d7..af74cc2de8b 100644 --- a/arch/arm/configs/kirkwood_defconfig +++ b/arch/arm/configs/kirkwood_defconfig @@ -629,7 +629,7 @@ CONFIG_SCSI_LOWLEVEL=y CONFIG_ATA=y # CONFIG_ATA_NONSTANDARD is not set CONFIG_SATA_PMP=y -# CONFIG_SATA_AHCI is not set +CONFIG_SATA_AHCI=y # CONFIG_SATA_SIL24 is not set CONFIG_ATA_SFF=y # CONFIG_SATA_SVW is not set diff --git a/arch/arm/mach-kirkwood/ts219-setup.c b/arch/arm/mach-kirkwood/ts219-setup.c index 01aa213c0a6..ec1a64f263d 100644 --- a/arch/arm/mach-kirkwood/ts219-setup.c +++ b/arch/arm/mach-kirkwood/ts219-setup.c @@ -206,6 +206,15 @@ static void __init qnap_ts219_init(void) } +static int __init ts219_pci_init(void) +{ + if (machine_is_ts219()) + kirkwood_pcie_init(); + + return 0; +} +subsys_initcall(ts219_pci_init); + MACHINE_START(TS219, "QNAP TS-119/TS-219") /* Maintainer: Martin Michlmayr */ .phys_io = KIRKWOOD_REGS_PHYS_BASE, -- cgit