summaryrefslogtreecommitdiffstats
path: root/drivers
Commit message (Collapse)AuthorAgeFilesLines
* r8169: PCI ID for Corega Gigabit network cardAndrew Morton2006-10-091-0/+1
| | | | | | | Fix for http://bugzilla.kernel.org/show_bug.cgi?id=7239. Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
* [netdrvr] b44: handle excessive multicast groupsJeff Garzik2006-10-051-3/+4
| | | | | | | | | | | | | If there are more than B44_MCAST_TABLE_SIZE groups in the dev->mc_list, it will only listen to the first B44_MCAST_TABLE_SIZE that it sees. This change makes the driver go into RXCONFIG_ALLMULTI mode if there are more than B44_MCAST_TABLE_SIZE groups being subscribed to, similar to other network drivers. Noticed by Bill Helfinstine <bhelf@flitterfly.whirpon.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [PATCH] bonding: fix deadlock on high loads in bond_alb_monitor()Karsten Keil2006-10-051-2/+2
| | | | | | | | | | | | | | In bond_alb_monitor the bond->curr_slave_lock write lock is taken and then dev_set_promiscuity maybe called which can take some time, depending on the network HW. If a network IRQ for this card come in the softirq handler maybe try to deliver more packets which end up in a request to the read lock of bond->curr_slave_lock -> deadlock. This issue was found by a test lab during network stress tests, this patch disable the softirq handler for this case and solved the issue. Signed-off-by: Karsten Keil <kkeil@suse.de> Acked-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [PATCH] forcedeth: hardirq lockdep warningPeter Zijlstra2006-10-051-14/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BUG: warning at kernel/lockdep.c:1816/trace_hardirqs_on() (Not tainted) Call Trace: show_trace dump_stack trace_hardirqs_on :forcedeth:nv_nic_irq_other handle_IRQ_event __do_IRQ do_IRQ ret_from_intr DWARF2 barf default_idle cpu_idle rest_init start_kernel _sinittext These 3 functions nv_nic_irq_tx(), nv_nic_irq_rx() and nv_nic_irq_other() are reachable from IRQ context and process context. Make use of the irq-save/restore spinlock variant. (Compile tested only, since I do not have the hardware) Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Jeff Garzik <jeff@garzik.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Dave Jones <davej@redhat.com> Cc: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [PATCH] mv643xx_eth: Fix ethtool statsMaxime Bizon2006-10-051-2/+2
| | | | | | | | | Some stats reported by ethtool -S on mv643xx_eth device are cleared between each call. This patch fixes it. Signed-off-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [PATCH] ibmveth: fix int rollover panicSantiago Leon2006-10-051-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | This patch fixes a nasty bug that has been sitting there since the very first versions of the driver, but is generating a panic because we changed the number of 2K buffers for 2.6.16. The consumer_index and producer_index are u32's that get incremented on every buffer emptied and replenished respectively. We use the {producer,consumer}_index mod'ed with the size of the pool to pick out an entry in the free_map. The problem happens when the u32 rolls over and the number of the buffers in the pool is not a perfect divisor of 2^32. i.e. if the number of 2K buffers is 0x300, before the consumer_index rolls over, our index to the free map = 0xffffffff mod 0x300 = 0xff. The next time a buffer is emptied, we want the index to the free map to be 0x100, but 0x0 mod 0x300 is 0x0. This patch assigns the mod'ed result back to the consumer and producer indexes so that they never roll over. The second chunk of the patch covers the unlikely case where the consumer_index has just been reset to 0x0 and the hypervisor is not able to accept that buffer. Signed-off-by: Santiago Leon <santil@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [PATCH] ibmveth: rename proc entry nameSantiago Leon2006-10-051-2/+6
| | | | | | | | | | | | | | This patch changes the name of the proc file for each ibmveth adapter from the network device name to the slot number in the virtual bus. The proc file is created when the device is probed, so a change in the name of the device will not be reflected in the name of the proc file giving problems when identifying and removing the adapter. The slot number is a property that does not change through the life of the adapter so we use that instead. Signed-off-by: Santiago Leon <santil@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [PATCH] ibmveth: kdump interrupt fixSantiago Leon2006-10-051-0/+2
| | | | | | | | | | | | | | | This patch fixes a race that panics the kernel when opening the device after a kdump. Without this patch there is a window where the hypervisor can send an interrupt before all the structures for the kdump ibmveth module are ready (because the hypervisor is not aware that the partition crashed and that the virtual driver is reloading). We close this window by disabling the interrupts before registering the adapter to the hypervisor. This patch depends on the "ibmveth: Harden driver initilisation" patch. Signed-off-by: Santiago Leon <santil@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [PATCH] ibmveth: Add netpoll functionSantiago Leon2006-10-051-0/+11
| | | | | | | | This patch adds the net poll controller function to ibmveth to support netconsole and netdump. Signed-off-by: Santiago Leon <santil@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [PATCH] ibmveth: Harden driver initilisationMichael Ellerman2006-10-051-6/+26
| | | | | | | | | | | | | | | | | | This patch has been floating around for a while now, Santi originally sent it in March: http://www.spinics.net/lists/netdev/msg00471.html After a kexec the ibmveth driver will fail when trying to register with the Hypervisor because the previous kernel has not unregistered. So if the registration fails, we unregister and then try again. We don't unconditionally unregister, because we don't want to disturb the regular code path for 99% of users. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Anton Blanchard <anton@samba.org> Signed-off-by: Santiago Leon <santil@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [PATCH] sky2: incorrect length on receive packetsStephen Hemminger2006-10-051-2/+2
| | | | | | | | | | The previous change to do fragmented receive (post 2.6.18) introduced a bug where packets are passed up with size set to the size of the receive buffer not the actual received data. IP silently trims this so it didn't show up right away. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [PATCH] itmtouch: fix inverted flag to indicate touch location correctly, ↵Mark Assad2006-10-041-3/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | correct white space There is a bug in the current version of the itmtouch USB touchscreen driver. The if statment that checks if pressure is being applied to the touch screen is now missing a ! (not), so events are no longer being reported correctly. The original source code for this line was as follows: #define UCP(x) ((unsigned char*)(x)) #define UCOM(x,y,z) ((UCP((x)->transfer_buffer)[y]) & (z)) ... if (!UCOM(urb, 7, 0x20)) { And was cleaned to: unsigned char *data = urb->transfer_buffer; .... if (data[7] & 0x20) { (note the lack of '!') This has been tested on an LG L1510BF and an LG1510SF touch screen. Signed-off-by: Mark Assad <massad@gmail.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Merge master.kernel.org:/pub/scm/linux/kernel/git/willy/parisc-2.6Linus Torvalds2006-10-041-2/+2
|\ | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/willy/parisc-2.6: [PA-RISC] Fix time.c for new do_timer() calling convention [PA-RISC] Fix must_check warnings in drivers.c [PA-RISC] Fix parisc_newuname() [PA-RISC] Remove warning from pci.c [PA-RISC] Fix filldir warnings [PA-RISC] Fix sys32_sysctl [PA-RISC] Fix sba_iommu compilation
| * [PA-RISC] Fix sba_iommu compilationMatthew Wilcox2006-10-051-2/+2
| | | | | | | | | | | | | | klist_iter_exit() only takes one parameter. Also fix warning by adding additional brackets. Signed-off-by: Matthew Wilcox <matthew@wil.cx>
* | Merge master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6Linus Torvalds2006-10-0477-733/+9852
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (54 commits) [SCSI] Initial Commit of qla4xxx [SCSI] raid class: handle component-add errors [SCSI] SCSI megaraid_sas: handle thrown errors [SCSI] SCSI aic94xx: handle sysfs errors [SCSI] SCSI st: fix error handling in module init, sysfs [SCSI] SCSI sd: fix module init/exit error handling [SCSI] SCSI osst: add error handling to module init, sysfs [SCSI] scsi: remove hosts.h [SCSI] scsi: Scsi_Cmnd convertion in aic7xxx_old.c [SCSI] megaraid_sas: sets ioctl timeout and updates version,changelog [SCSI] megaraid_sas: adds tasklet for cmd completion [SCSI] megaraid_sas: prints pending cmds before setting hw_crit_error [SCSI] megaraid_sas: function pointer for disable interrupt [SCSI] megaraid_sas: frame count optimization [SCSI] megaraid_sas: FW transition and q size changes [SCSI] qla2xxx: Update version number to 8.01.07-k2. [SCSI] qla2xxx: Stall mid-layer error handlers while rport is blocked. [SCSI] qla2xxx: Add MODULE_FIRMWARE tags. [SCSI] qla2xxx: Add support for host port state FC transport attribute. [SCSI] qla2xxx: Add support for fabric name FC transport attribute. ...
| * [SCSI] Initial Commit of qla4xxxDavid Somayajulu2006-10-0418-0/+7540
| | | | | | | | | | | | | | | | | | | | open-iSCSI driver for Qlogic Corporation's iSCSI HBAs Signed-off-by: Ravi Anand <ravi.anand@qlogic.com> Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com> Signed-off-by: Doug Maxey <dwm@bubba.enoyolf.org> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] raid class: handle component-add errorsJeff Garzik2006-10-041-4/+16
| | | | | | | | | | Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] SCSI megaraid_sas: handle thrown errorsJeff Garzik2006-10-041-12/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | - handle clear_user() error - handle and properly unwind from sysfs errors thrown during mod init - adjust order of calls in megasas_exit() to precisely match registration order in megasas_init() Signed-off-by: Jeff Garzik <jeff@garzik.org> Updated for extra attribute and Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] SCSI aic94xx: handle sysfs errorsJeff Garzik2006-10-041-8/+33
| | | | | | | | | | | | | | Handle and unwind from errors returned by driver model functions. Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] SCSI st: fix error handling in module init, sysfsJeff Garzik2006-10-041-37/+78
| | | | | | | | | | | | | | | | | | | | | | - Notice and handle sysfs errors in module init, tape init - Properly unwind errors in module init - Remove bogus st_sysfs_class==NULL test, it is guaranteed !NULL at that point Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] SCSI sd: fix module init/exit error handlingJeff Garzik2006-10-041-5/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Properly handle and unwind errors in init_sd(). Fixes leaks on error, if class_register() or scsi_register_driver() failed. - Ensure that exit_sd() execution order is the perfect inverse of initialization order. FIXME: If some-but-not-all register_blkdev() calls fail, we wind up calling unregister_blkdev() for block devices we did not register. This was a pre-existing bug. Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] SCSI osst: add error handling to module init, sysfsJeff Garzik2006-10-041-40/+91
| | | | | | | | | | | | | | | | | | | | | | | | | | | | - check all sysfs-related return codes, and propagate them back to callers - properly unwind errors in osst_probe(), init_osst(). This fixes a leak that occured if scsi driver registration failed, and fixes an oops if sysfs creation returned an error. (unrelated) - kzalloc() cleanup in new_tape_buf() Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] scsi: remove hosts.hHenne2006-10-045-11/+2
| | | | | | | | | | | | | | Remove the obsolete hosts.h file under drivers/scsi. Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] scsi: Scsi_Cmnd convertion in aic7xxx_old.cHenne2006-10-041-154/+144
| | | | | | | | | | | | | | | | | | Changes the obsolete Scsi_Cmnd to struct scsi_cmnd in aic7xxx_old.c. Also replacing lots of whitespaces with tabs in structures and functions which have been changed. Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] megaraid_sas: sets ioctl timeout and updates version,changelogSumant Patro2006-10-042-7/+12
| | | | | | | | | | | | | | | | This patch sets timeout of max 180 seconds for ioctl completion. It also updates the Changelog and hikes the version to 3.05. Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] megaraid_sas: adds tasklet for cmd completionSumant Patro2006-10-042-22/+45
| | | | | | | | | | | | | | This patch adds a tasklet for command completion. Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] megaraid_sas: prints pending cmds before setting hw_crit_errorSumant Patro2006-10-042-0/+94
| | | | | | | | | | | | | | | | | | This patch adds function to print the pending frame details before returning failure from the reset routine. It also exposes a new variable megasas_dbg_lvl that allows the user to set the debug level for logging. Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] megaraid_sas: function pointer for disable interruptSumant Patro2006-10-042-23/+33
| | | | | | | | | | | | | | | | | | This patch adds function pointer to invoke disable interrupt for xscale and ppc IOP based controllers. Removes old implementation that checks for controller type in megasas_disable_intr. Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] megaraid_sas: frame count optimizationSumant Patro2006-10-041-25/+47
| | | | | | | | | | | | | | | | | | | | This patch removes duplicated code in frame calculation & adds megasas_get_frame_count() that also takes into account the number of frames that can be contained in the Main frame. FW uses the frame count to pull sufficient number of frames from host memory. Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] megaraid_sas: FW transition and q size changesSumant Patro2006-10-042-8/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch has the following enhancements : a. handles new transition states of FW to support controller hotplug. b. It reduces by 1 the maximum cmds that the driver may send to FW. c. Sends "Stop Processing" cmd to FW before returning failure from reset routine d. Adds print in megasas_transition routine e. Sends "RESET" flag to FW to do a soft reset of controller to move from Operational to Ready state. f. Sending correct pointer (cmd->sense) to pci_pool_free Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] qla2xxx: Update version number to 8.01.07-k2.Andrew Vasquez2006-10-031-1/+1
| | | | | | | | | | Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] qla2xxx: Stall mid-layer error handlers while rport is blocked.Andrew Vasquez2006-10-031-0/+25
| | | | | | | | | | | | | | | | | | | | | | Stall error handler if attempting recovery while an rport is blocked. This avoids device offline scenarios due to errors in the error handler. Reference implementation from lpfc/mptfc. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] qla2xxx: Add MODULE_FIRMWARE tags.Andrew Vasquez2006-10-031-5/+16
| | | | | | | | | | Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] qla2xxx: Add support for host port state FC transport attribute.Andrew Vasquez2006-10-031-0/+15
| | | | | | | | | | Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] qla2xxx: Add support for fabric name FC transport attribute.Andrew Vasquez2006-10-033-1/+19
| | | | | | | | | | Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] qla2xxx: Add support for system hostname FC transport attribute.Andrew Vasquez2006-10-032-0/+25
| | | | | | | | | | | | | | | | The system hostname will be used during a subsequent FDMI registration with the fabric. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] qla2xxx: Add support for symbolic nodename FC transport attribute.Andrew Vasquez2006-10-033-15/+22
| | | | | | | | | | | | | | Refactored original code from qla_gs.c:qla2x00_rsnn_nn(). Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] qla2xxx: Add iIDMA support.Andrew Vasquez2006-10-038-12/+401
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | iIDMA (Intelligent Interleaved Direct Memory Access) allows for the HBA hardware to send FC frames at the rate at which they can be received by a target device. By taking advantage of the higher link rate, the HBA can maximize bandwidth utilization in a heterogeneous multi-speed SAN. Within a fabric topology, port speed detection is done via a Name Server command (GFPN_ID) followed by a Fabric Management command (GPSC). In an FCAL/N2N topology, port speed is based on the HBA link-rate. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] scsi: Scsi_Cmnd convertion in arm subtreeHenne2006-10-037-97/+108
| | | | | | | | | | | | | | | | | | Changes the obsolete Scsi_Cmnd to struct scsi_cmnd in the arm subdir of the scsi-subsys. Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de> Acked-by: Russell King <rmk@arm.linux.org.uk> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] scsi: Convertion to struct scsi_cmnd in ips-driverHenne2006-10-032-53/+46
| | | | | | | | | | | | | | Converts the obsolete Scsi_Cmnd to struct scsi_cmnd in the ips-driver. Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] enable clustering for tmscsimGuennadi Liakhovetski2006-10-031-1/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | following an email from John Adams <johna@onevista.com> to me with a patch to enable tmscsim to use blocks up to 1MB and a discussion on linux-scsi, below is a patch to enable clustering for tmscsim. I made it switchable with a module parameter, with default "enable" - in case somebody gets problems with it. Unfortunately, I was not able to check if this alone lets you use any bigger blocks with a tape, as my tape seems to only support 1 block size - only "mt setblk 1" is successful, any other value fails. OTOH, testing on a P-133 showed that enabling clustering alone improves throughput by 10% and reduces CPU load by another 10%, so, seems a worthy thing to do. As for setting max_sectors, that might become a separate patch... Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] scsi_devinfo: scsi2 HP and Hitachi entriesMike Christie2006-10-011-0/+13
| | | | | | | | | | | | | | When SCSI-2 they can support luns past 7 and sparse luns. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] scsi_devinfo: add nec iStorageMike Christie2006-10-011-0/+1
| | | | | | | | | | | | | | support the report luns opcode . Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] scsi_devinfo: add TornadoMike Christie2006-10-011-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | This is from RHEL4. I do not have any info from our bugzilla. All I could find was something like this thread http://lkml.org/lkml/2005/1/7/346 Report lun for linux does not work. It may be our lun format code or it may be the device. It is probably not worth it to add anything special for this device, so the patch just adds BLIST_NOREPORTLUN. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] scsi_devinfo: add EMC InvistaMike Christie2006-10-011-0/+1
| | | | | | | | | | | | | | | | This is from RHEL4. This box can support scsi2 and can also support BLIST_SPARSELUN | BLIST_LARGELUN. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] trivial scsi_execute_async fixArne Redlich2006-10-011-1/+1
| | | | | | | | | | | | | | | | | | In scsi_execute_async()'s error path, a struct scsi_io_context allocated with kmem_cache_alloc() is kfree()'d. Obviously kmem_cache_free() should be used instead. Signed-off-by: Arne Redlich <arne.redlich@xiranet.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] stex: add new device (id 0x8650) supportEd Lin2006-10-011-30/+164
| | | | | | | | | | | | | | | | | | | | | | | | | | A new device (id 0x8650, nickname 'yosemite') support is added. It's basically the same, except for following items: - mapping of id and lun by firmware - special handling for some commands in interrupt routine - change of internal copy function for these special commands - different reset handling code - different shutdown notification command Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] stex: cancel unused field in struct req_msgEd Lin2006-10-011-2/+1
| | | | | | | | | | | | | | | | | | | | The payload_sz field in struct req_msg is not big enough to indicate the size of req_msg, as its type is u8. It is confirmed that this field is not used by firmware, so cancel it here. Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] fix scsi_device_types overrun in scsi.cEric Sesterhenn2006-10-011-1/+1
| | | | | | | | | | | | | | | | | | this overrun was spotted by coverity (cid #1403). If type == ARRAY_SIZE(scsi_device_types), we are off by one. Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] aic7xxx: fix byte I/O order in ahd_inwDenis Vlasenko2006-10-012-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Comment says "Read high byte first as some registers increment..." but code doesn't guarantee that, I think: return ((ahd_inb(ahd, port+1) << 8) | ahd_inb(ahd, port)); Compiler can reorder it. Make the order explicit. Signed-off-by: Denis Vlasenko <vda.linux@googlemail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Fixed rejections and added aic7xxx code Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
generated by cgit (git 2.34.1) at 2025-01-31 07:49:04 +0000