summaryrefslogtreecommitdiffstats
path: root/drivers/net
Commit message (Collapse)AuthorAgeFilesLines
* iwlagn: invoke L0S workaround for 6000/1000 seriesBen Cahill2009-11-023-14/+18
| | | | | | | | | | | | Invoke workaround to avoid instability in L0->L0S->L1 transition on PCIe bus. Workaround disables L0S state so device moves directly from L0->L1. Workaround needed on all devices since and including 4965; add to 6000/1000. Describe bug and workaround better in comments. Signed-off-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: remove power-wasting calls to apm_ops.init()Ben Cahill2009-11-023-13/+11
| | | | | | | | | | | | | | | | | | To save power, don't run apm_ops.init() until needed at "up" time. EEPROM (5000 and earlier devices) may be read without running apm_ops.init(), but OTP reads (6000 and newer devices) require a powered-up chip. Therefore, remove apm_ops.init() from the general path in XXXX_pci_probe(), and call it only if device uses OTP. Once done with OTP read, call apm_ops.stop() to reset chip and save power until "up" time comes around. NOTE: This patch depends on removal of priv->lock from iwl_apm_stop(); lock does not get initialized until later in flow. See patch "remove unneeded locks from apm_stop()". Signed-off-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: remove unneeded locks from apm_stop() and stop_master()Ben Cahill2009-11-021-13/+13
| | | | | | | | | | | | | | | | | Since priv->reg_lock was added to keep multi-access register manipulation atomic, priv->lock protection is no longer needed. Remove this from iwl_apm_stop_master() and iwl_apm_stop(). Add warning of timeout when polling for busmaster disablement confirmation, and some comments. NOTE: This is needed to enable use of apm_ops.stop() within iwl_eeprom_init(); priv->lock does not get initialized until after this flow. See patch "remove power-wasting calls to apm_ops.init()" Signed-off-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: provide firmware versionReinette Chatre2009-11-022-0/+16
| | | | | | | | | | | | | | | | | | | By setting the firmware version in wiphy it is possible to obtain this information via ethtool. Some examples, # ethtool -i wlan1 driver: iwlagn version: 2.6.32-rc5-wl-56840-g26d8540 firmware-version: 228.57.2.23 bus-info: 0000:03:00.0 # ethtool -i wlan0 driver: iwl3945 version: 2.6.32-rc5-wl-56840-g26d8540 firmware-version: 15.28.2.8 bus-info: 0000:02:00.0 Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* libertas: remove internal buffers from GSPI driverAndrey Yurovsky2009-11-021-130/+6
| | | | | | | | | | | | | | | | | | | | | | | | | This patch removes the internal command and data buffers that the GSPI driver maintained and instead relies on the Libertas core to synchronize access to the command and data ports as with the other interface drivers. This cleanup reduces the GSPI driver's memory footprint and should improve performance by removing the need to copy to these internal buffers. This also simplifies the bottom half of the interrupt handler. This is an incremental cleanup: after removing the redundant buffers, we can further improve the driver to use a threaded IRQ handler instead of maintaining its own thread. However I would like a few folks to test the buffer removal first and make sure that I'm not introducing regressions. Tested on Blackfin BF527 with DMA disabled due to an issue with the SPI host controller driver in the current bleeding-edge Blackfin kernel. I would appreciate it if someone with working DMA could test this patch and provide feedback. Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Tested-by: George Shore <george.shore@imgtec.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43legacy: Fix DMA TX bounce buffer copyingLarry Finger2009-10-301-2/+15
| | | | | | | | This patch is adapted from the submission by Michael Buesch <mb@bu3sch.de> for a bounce-buffer copying problem with b43. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1271: fix init loop timeoutLuciano Coelho2009-10-301-1/+1
| | | | | | | | | | | | The check after the loop which checks whether the initialization timed-out was wrong. If the initialization would succeed exactly in the 20000th time (the value set for INIT_LOOP), the driver would bail out and claim that initialization failed. Reported-by: Juha Leppanen <juha_motorsportcom@luukku.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wireless: airo_cs needs WEXT_SPYRandy Dunlap2009-10-301-0/+1
| | | | | | | | | | | | | airo_cs uses spy interfaces so it needs to select WEXT_SPY. ERROR: "iw_handler_set_thrspy" [drivers/net/wireless/airo.ko] undefined! ERROR: "wireless_spy_update" [drivers/net/wireless/airo.ko] undefined! ERROR: "iw_handler_get_spy" [drivers/net/wireless/airo.ko] undefined! ERROR: "iw_handler_get_thrspy" [drivers/net/wireless/airo.ko] undefined! ERROR: "iw_handler_set_spy" [drivers/net/wireless/airo.ko] undefined! Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: make ath9k_phy_modify_rx_buffer() staticLuis R. Rodriguez2009-10-301-130/+126
| | | | | | | To do this we reorder callers in order in which they are called. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: Fix and complete force bias for AR5416Luis R. Rodriguez2009-10-302-1/+73
| | | | | | | | | | | | | | | | Force bias is a fix for usage of AR5416 radios on the 2.4 GHz band for orientation sensitivity. This was only partially implemented with the ath9k_hw_decrease_chain_power() but first -- this was being called for all chipsets which is not correct and second -- it was missing the actual orientation code. We now ensure to only enable force bias only for AR5416 and BUG_ON() on other chipsets. Although ath9k_hw_decrease_chain_power() was enabled for newer chipsets I suspect that it never ran unless the EEPROM had ATH9K_ANT_FIXED_A or ATH9K_ANT_FIXED_B for antenna diversity. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: remove unused modesIndex param from ath9k_hw_write_regs()Luis R. Rodriguez2009-10-303-6/+3
| | | | | Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: make spur mitigation a callbackLuis R. Rodriguez2009-10-302-11/+11
| | | | | | | | This only differs between single-chip solutions and non single-chip solutions. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: order phy.c code and integrate spur mitigationLuis R. Rodriguez2009-10-303-614/+637
| | | | | | | | | | | This reorders phy.c routines in the order in the order in which they are used and also moves the spur mitigation helpers for each type of chip into phy.c as they are RF related. This patch has no functional changes. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: use a callback for frequency changeLuis R. Rodriguez2009-10-302-10/+9
| | | | | | | This avoids a branch on every channel change. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: make both analog channel change routines return intLuis R. Rodriguez2009-10-303-23/+22
| | | | | | | This allows us to later define a callback for both. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: rename ath9k_hw_rf_free() to ath9k_hw_rf_free_ext_banks()Luis R. Rodriguez2009-10-304-5/+10
| | | | | | | This clarifies this is only required for external radios. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: simplify ath9k_hw_rf_alloc_ext_banks()Luis R. Rodriguez2009-10-301-52/+20
| | | | | | | | This is calling an allocation and checking for it, simplify this process in a macro. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: simplify rf attach and rename to ath9k_hw_rf_alloc_ext_banks()Luis R. Rodriguez2009-10-303-32/+17
| | | | | | | | | | | | | ath9k_hw_rfattach() was just calling a helper and this helper was doing nothing for single-chip devices, and for non single-chip devices it is just allocating memory for banks to program the RF registers at a later time. Simplify this by having the hw initialization call the rf bank allocation directly for external radios. Also, propagate an -ENOMEM properly now upon failure. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: bail out early on ath9k_hw_init_rf()Luis R. Rodriguez2009-10-301-54/+55
| | | | | | | | | | | We a huge branch for old hardware and nothing for newer hardware. Instead of doing this just bail out early for newer hardware. This patch has no functional changes. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: start documenting 802.11n RF anlong front endsLuis R. Rodriguez2009-10-302-5/+170
| | | | | | | | | | | | | | | | | | | | | | Document what we can about the RF analog front ends (radios) of Atheros 802.11n devices. What should be clearer now is the what we do for old pre AR5416 and AR5418 MAC based devices in comparison to the modern sigle-chip 802.11n solutions. All devices after AR9280 are single chip and require less programming -- the RF registers no longer need to be initialized as they all have the RF analog front end embedded together with the MAC/BB; this includes the AR9271. Older devices such as the ones with the AR5416 MACs (PCI) or AR5418 MACs (PCI-E) have an external 2.4 GHz AR2133 radio or a dual band 2.4 GHz / 5 GHz AR5133 radio. These external radios require additional programming of the RF registers. Clarify which parts are for what devices and which code is shared. This patch has no functional changes. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: change the way we initialize the pll for ar9271Luis R. Rodriguez2009-10-302-0/+39
| | | | | | | | | We adjust the core clock for ar9271 to 117 MHz; this also requires us to adjust the baud divider based on the targetted baud rate. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: update register initialization/reset values for ar9271Luis R. Rodriguez2009-10-303-16/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This update the register initialization/reset values (aka initvals) for ar9271 based on the last recommended values on 2009-06-04 by our systems engineering team. The changes account for: * Supporting ar9271 1.0 and ar9271 1.1 together, the difference is bb_spectral_scan_ena, for 1.0 we'll set this to 0x1. * Ensuring we get the correct noise floor values -115 ~ -118 when we enable bb_enable_ant_div_lnadiv=0 and mc_tx_def_ant_sel=1. Previous to this we would get noise floor values in the range -50 ~ -80. To fix settings for the registers: - bb_ch1_xatten1_db - bb_ch1_xatten2_db - bb_ch1_xatten1_margin - bb_ch1_xatten2_margin - bb_ch1_gain_force - bb_ch1_xatten2_hyst_margin - bb_ch1_xatten1_hyst_margin - bb_ch1_max_oc_gain * 0x8120[2] mc_mic_new_location_enable is changed to 0x1. The MAC team suggest to set this value. * 0x9910[0] bb_spectral_scan_ena is changed to 0x0. For ar9271 1.1 we don't need to enable this bit. Cc: Stephen Chen <Stephen.Chen@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: modify the rf control register for ar9271 revision 1.0Luis R. Rodriguez2009-10-301-0/+4
| | | | | Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wireless: remove WLAN_80211 and WLAN_PRE80211 from KconfigJohn W. Linville2009-10-3017-51/+31
| | | | | | | With the WLAN_PRE80211 drivers moved to drivers/staging, this distinction becomes unnecessary. Signed-off-by: John W. Linville <linville@tuxdriver.com>
* netwave: move driver to stagingJohn W. Linville2009-10-303-1405/+0
| | | | | | | | | | | | | Move the netwave driver to drivers/staging. This is another pre-802.11 driver that has seen virtually no non-API-fixup activity in years, and for which no active hardware is likely to still exist. This driver represents unnecessary ongoing maintenance for no clear benefit. This patch brought to you by the "hacking" session at the 2009 Kernel Summit in Tokyo, Japan... Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wavelan: move driver to stagingJohn W. Linville2009-10-3010-11919/+0
| | | | | | | | | | | | | Move the wavelan driver to drivers/staging. This is another pre-802.11 driver that has seen virtually no non-API-fixup activity in years, and for which no active hardware is likely to still exist. This driver represents unnecessary ongoing maintenance for no clear benefit. This patch brought to you by the "hacking" session at the 2009 Kernel Summit in Tokyo, Japan... Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* arlan: move driver to stagingJohn W. Linville2009-10-305-3699/+0
| | | | | | | | | | | | | Move the arlan driver to drivers/staging. This is another pre-802.11 driver that has seen virtually no non-API-fixup activity in years, and for which no active hardware is likely to still exist. This driver represents unnecessary ongoing maintenance for no clear benefit. This patch brought to you by the "hacking" session at the 2009 Kernel Summit in Tokyo, Japan... Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* strip: move driver to stagingJohn W. Linville2009-10-303-2829/+0
| | | | | | | | | | | | | Move the strip ("Starmode Radio IP") driver to drivers/staging. For several years this driver has only seen API "bombing-run" changes, and few people ever had the hardware. This driver represents unnecessary ongoing maintenance for no clear benefit. This patch brought to you by the "hacking" session at the 2009 Kernel Summit in Tokyo, Japan... Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: remove RX_FLAG_RADIOTAPJohannes Berg2009-10-302-2/+2
| | | | | | | | | | | | | | | | | | | | | | | While there may be a case for a driver adding its own bits of radiotap information, none currently does. Also, drivers would have to copy the code to generate the radiotap bits that now mac80211 generates. If some driver in the future needs to add some driver-specific information I'd expect that to be in a radiotap vendor namespace and we can add a different way of passing such data up and having mac80211 include it. Additionally, rename IEEE80211_CONF_RADIOTAP to IEEE80211_CONF_MONITOR since it's still used by b43(legacy) to obtain per-frame timestamps. The purpose of this patch is to simplify the RX code in mac80211 to make it easier to add paged skb support. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211_hwsim: don't register CCK rates on 5ghzJohannes Berg2009-10-301-3/+4
| | | | | | | This buglet confused me a lot just now ... Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: remove bogus register write on ath9k_hw_9271_pa_cal()Luis R. Rodriguez2009-10-301-1/+1
| | | | | | | | | An extra register was being written to for PA calibration making the hardware unresponsive, remove it. Hardware reset should now complete fine on ar9271. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: correct AR_PHY_SPECTRAL_SCAN register offsetLuis R. Rodriguez2009-10-302-3/+16
| | | | | | | | | | We had 0x9912 but AR_PHY_SPECTRAL_SCAN is 0x9910. By using the 0x9912 we were making the hardware unresponsive. This allows us to move forward with hardware reset on ar9271 on the ath9k_htc driver. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: add AR9271 single chip name mappingLuis R. Rodriguez2009-10-301-1/+2
| | | | | Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: distinguish single-chip solutions on initial probe printLuis R. Rodriguez2009-10-304-20/+36
| | | | | | | | | | Devices with external radios have revisions which we can count on. On single chip solutions these EEPROM values for these radio revision also exist but are not meaningful as the radios are embedded onto the same chip. Each single-chip device evolves together as one device. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: move mac name and rf name helpers to hw codeLuis R. Rodriguez2009-10-305-62/+71
| | | | | | | These are shared between ath9k and the future ath9k_htc driver. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: enable power saveKalle Valo2009-10-301-1/+2
| | | | | | | wl1251 supports power save and it can be enabled now. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: LP-PHY: Begin implementing calibration & software RFKILL supportGábor Stefanik2009-10-302-136/+658
| | | | | | | | | | | | | | | | | | | | This implements the following calibration functions: -Set TX IQCC -Set TX Power by Index -PR41573 workaround (incomplete, needs PHY reset) -Calc RX IQ Comp -PHY Cordic -Run Samples -Start/Stop TX Tone -part of PAPD Cal TX Power -RX I/Q Calibration -The basic structure of the periodic calibration wrapper Software RFKILL (required by calibration) is also implemented in this round. Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* convert kaweth to use usb_reset_configuration()Oliver Neukum2009-10-291-10/+1
| | | | | | | | | | | | | | | | For USB 3.0 it is necessary that all drivers use the standard API to reset a configuration. This removes a home-grown implementation. Signed-off-by: Oliver Neukum <oliver@neukum.org> Hi David, please take this for the next merge window. Regards Oliver Signed-off-by: David S. Miller <davem@davemloft.net>
* sky2: version 1.26Stephen Hemminger2009-10-291-1/+1
| | | | | Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sky2: 88E8059 supportStephen Hemminger2009-10-291-1/+78
| | | | | | | | | Tentative support for newer Marvell hardware including the Yukon-2 Optima chip. Do not have hatdware to test this yet, code is based on vendor driver. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sky2: workarounds for Yukon-2 supremeStephen Hemminger2009-10-291-2/+32
| | | | | | | | | Changes related to support of Yukon supreme chip. Don't have this chip version to test on, these are reverse engineered from the vendor (GPL) driver. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sky2: fix receive pause thresholdsStephen Hemminger2009-10-292-5/+12
| | | | | | | | Program the receive pause thresholds differently depending on chip version. This cloned from from the vendor (GPL) driver. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sky2: add register definitions for new chipsStephen Hemminger2009-10-291-1/+177
| | | | | | | | This adds infrastructure for the newer chip versions and workarounds. Extracted from the vendor (GPL) driver. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sky2: add SK-9E21M device idStephen Hemminger2009-10-291-0/+1
| | | | | | | This is a new ID that just showed up in latest vendor driver. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Enable heuristic selection between page and skb RX buffersBen Hutchings2009-10-291-1/+1
| | | | | | | | Now that we can tell whether GRO is being applied, this heuristic is effective once more. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Feed GRO result into RX allocation policy and interrupt moderationBen Hutchings2009-10-291-2/+11
| | | | | | | | | | | | When GRO is successfully merging received packets, we should allocate raw page buffers rather than skbs that will be discarded by GRO. Otherwise, we should allocate skbs. GRO also benefits from higher interrupt moderation, so increase the score for mergeable RX packets. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2009-10-2915-61/+107
|\ | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
| * netdev: usb: dm9601.c can drive a device not supported yet, add support for itJanusz Krzysztofik2009-10-291-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | I found that the current version of drivers/net/usb/dm9601.c can be used to successfully drive a low-power, low-cost network adapter with USB ID 0a46:9000, based on a DM9000E chipset. As no device with this ID is yet present in the kernel, I have created a patch that adds support for the device to the dm9601 driver. Created and tested against linux-2.6.32-rc5. Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
| * qlge: Fix firmware mailbox command timeout.Ron Mercer2009-10-292-11/+13
| | | | | | | | | | | | | | | | | | The mailbox command process would only process a maximum of 5 unrelated firmware events while waiting for it's command completion status. It should process an unlimited number of events while waiting for a maximum of 5 seconds. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * qlge: Fix EEH handling.Ron Mercer2009-10-291-26/+52
| | | | | | | | | | | | | | | | Clean up driver resources without touch the hardware. Add pci save/restore state. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2024-11-18 17:21:16 +0000