summaryrefslogtreecommitdiffstats
path: root/drivers/ide/pci
Commit message (Collapse)AuthorAgeFilesLines
* ide: add PIO masksBartlomiej Zolnierkiewicz2007-07-2030-8/+70
| | | | | | | | | | | | | * Add ATA_PIO[0-6] defines to <linux/ata.h>. * Add ->pio_mask field to ide_pci_device_t and ide_hwif_t. * Add PIO masks to host drivers. <linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: remove ide_find_best_pio_mode()Bartlomiej Zolnierkiewicz2007-07-202-17/+25
| | | | | | | | | | | | | | | | | * Add ->host_flags to ide_hwif_t to store ide_pci_device_t.host_flags, assign it in setup-pci.c:ide_pci_setup_ports(). * Add IDE_HFLAG_PIO_NO_{BLACKLIST,DOWNGRADE} to ide_pci_device_t.host_flags and teach ide_get_best_pio_mode() about them. Also remove needless !drive->id check while at it (drive->id is always present). * Convert amd74xx, via82cxxx and ide-timing.h to use ide_get_best_pio_mode() and then remove no longer needed ide_find_best_pio_mode(). There should be no functionality changes caused by this patch. Acked-by: Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: drop "PIO data" argument from ide_get_best_pio_mode()Bartlomiej Zolnierkiewicz2007-07-2027-34/+33
| | | | | | | | | | * Drop no longer needed "PIO data" argument from ide_get_best_pio_mode() and convert all users accordingly. * Remove no longer needed ide_pio_data_t. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add ide_pio_cycle_time() helper (take 2)Bartlomiej Zolnierkiewicz2007-07-203-19/+19
| | | | | | | | | | | | | | | | * Add ide_pio_cycle_time() helper. * Use it in ali14xx/ht6560b/qd65xx/cmd64{0,x}/sl82c105 and pmac host drivers (previously cycle time given by the device was only used for "pio" == 255). * Remove no longer needed ide_pio_data_t.cycle_time field. v2: * Fix "ata_" prefix (Noticed by Jeff). Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* sc1200: remove stale Power Management codeBartlomiej Zolnierkiewicz2007-07-201-37/+2
| | | | | | | | | | | | | | | * Nowadays core IDE code handles restoring of PIO and DMA modes (ide-io.c:ide_start_power_step() etc) so remove open-coded version from sc1200_resume(). There should be no change in behavior because settings done by sc1200_resume() were always overridden by generic_ide_resume() and ide_{start,stop}_power_step(). * Bump driver version. Cc: Mark Lord <mlord@pobox.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* serverworks: fix DMABartlomiej Zolnierkiewicz2007-07-201-6/+2
| | | | | | | | | | | The driver used to depend on BIOS settings for deciding whether it is OK to use DMA. However it seems that BIOS doesn't always handle all cases correctly so just let IDE core to decide about this. It should be a safe thing to do now, after the driver went through heavy bugfixing. Thanks for bugreport and testing the patch goes out to Sven Niedner. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* serverworks: always tune PIOBartlomiej Zolnierkiewicz2007-07-201-40/+36
| | | | | | | | | | | | | | | | | | * Always set ->autotune so PIO gets correctly auto-tuned (previously ->autotune was only set when ->dma_base wasn't available, however ->ide_dma_check()/->speedproc() was always trying to tune PIO when tuning DMA). * Move code responsible for programming chipset for PIO mode from svwks_tune_chipset() to svwks_tune_pio(). Don't tune PIO when tuning DMA (this is no longer needed since ->autotune is always set now). * Handle PIO modes early in svwks_tune_chipset() so DMA configuration registers don't get cleared when programming PIO mode. * Bump driver version. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add ide_pci_device_t.host_flags (take 2)Bartlomiej Zolnierkiewicz2007-07-2033-85/+19
| | | | | | | | | | | | | | | | | | * Rename ide_pci_device_t.flags to ide_pci_device_t.host_flags and IDEPCI_FLAG_ISA_PORTS flag to IDE_HFLAG_ISA_PORTS. * Add IDE_HFLAG_SINGLE flag for single channel devices. * Convert core code and all IDE PCI drivers to use IDE_HFLAG_SINGLE and remove no longer needed ide_pci_device_t.channels field. v2: * Fix issues noticed by Sergei: - correct code alignment in scc_pata.c - s/IDE_HFLAG_SINGLE/~IDE_HFLAG_SINGLE/ in serverworks.c Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add ide_dev_has_iordy() helper (take 4)Bartlomiej Zolnierkiewicz2007-07-201-3/+7
| | | | | | | | | | | | | | | | | | * Add ide_dev_has_iordy() helper and use it sl82c105 host driver. * Remove no longer needed ide_pio_data_t.use_iordy field. v2/v3: * Fix issues noticed by Sergei: - correct patch description - fix comment in ide_get_best_pio_mode() v4: * Fix "ata_" prefix (Noticed by Jeff). Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: make ide_get_best_pio_mode() print info if overriding PIO modeBartlomiej Zolnierkiewicz2007-07-202-7/+5
| | | | | | | | | | | * Print info about overriding PIO mode in ide_get_best_pio_mode(). * Remove info about overriding PIO mode from cmd64{0,x} host drivers. * Remove no longer needed ide_pio_data_t.overridden field. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* siimage: PIO mode setup fixes (take 2)Bartlomiej Zolnierkiewicz2007-07-201-98/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Add sil_tuneproc() wrapper for siimage_tuneproc() which also sets PIO mode on the device. * Add missing ide_get_best_pio_mode() call to sil_tuneproc() so "pio" == 255 (autotune) is handled correctly (previously PIO0 was used) and "pio" values > 4 && < 255 are filtered to PIO4 (instead of PIO0). * Add code limiting maximum PIO mode according to the pair device capabilities to sil_tuneproc(). * Convert users of config_siimage_chipset_for_pio() to use sil_tune_pio() and sil_tuneproc(). This fixes PIO fallback in siimage_config_drive_for_dma() to use max PIO mode available instead of PIO4 (config_siimage_chipset_for_pio() used wrong arguments for ide_get_best_pio_mode() and as a results always tried to set PIO4). * Remove no longer needed siimage_taskfile_timing() and config_siimage_chipset_for_pio(). * Enable ->autotune unconditionally and remove PIO tuning for UDMA/MDMA modes from siimage_speedproc() * Bump driver version. v2: * Fix issues noticed by Sergei: - correct pair device check - trim only taskfile PIO to the slowest of the master/slave - enable ->autotune unconditionally and remove PIO tuning for UDMA/MDMA modes from siimage_speedproc() - add TODO item for IORDY bugs - minor cleanups Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* atiixp: PIO mode setup fixesBartlomiej Zolnierkiewicz2007-07-201-13/+19
| | | | | | | | | | | | | | | | | | | | | | * Split off exisiting atiixp_tuneproc() into atiixp_tune_pio() and then add setting device PIO mode to atiixp_tuneproc(). * Add missing ide_get_best_pio_mode() call to atiixp_tuneproc() so "pio" == 255 (autotune) is handled correctly and "pio" values > 4 && < 255 are filtered to PIO4 (previously "pio" == 5 could result in wrong timings being used and "pio" values > 4 && < 255 in an OOPS). * Handle PIO modes early in atiixp_speedproc() so save_mdma_mode[] doesn't get cleared. * In atiixp_dma_check(): - fix max_mode argument for ide_get_best_pio_mode() - don't call atiixp_dma_2_pio() so PIO1 doesn't get remapped to PIO0 - use atiixp_tuneproc() instead of atiixp_speedproc() * Bump driver version. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: Stop mapping ROMsAlan Cox2007-07-205-38/+2
| | | | | | | | | | | | | Various old IDE drivers go mapping ROM devices for no apparent reason and without using the ROM mapping API we now have. They don't actually use the ROM they map and the new libata drivers are happy without it being mapped so rather than port them lets just junk it for the next -rc1. Signed-off-by: Alan Cox <alan@redhat.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Andrew Morton <akpm@osdl.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* scc_pata.c: Workaround for errata A308 (take 2)Kou Ishizaki2007-07-201-13/+54
| | | | | | | | | | | | | Workaround for errata A308: turn down the UDMA mode and retry the DMA command when the data lost condition is detected. take2: udma_filter() hook is used to limit ATAPI UDMA mode. Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* scc_pata: Use inline function for eieioKumar Gala2007-07-201-2/+2
| | | | | | | | | | Move to using inline function variant of eieio instead of inline assmebly. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Cc: kou.ishizaki@toshiba.co.jp Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* PCI: add pci_try_set_mwiRandy Dunlap2007-07-111-1/+1
| | | | | | | | | | | | | | | As suggested by Andrew, add pci_try_set_mwi(), which does not require return-value checking. - add pci_try_set_mwi() without __must_check - make it return 0 on success, errno if the "try" failed or error - review callers Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* PCI: Change all drivers to use pci_device->revisionAuke Kok2007-07-119-57/+22
| | | | | | | | | | | | | | | | | | | | Instead of all drivers reading pci config space to get the revision ID, they can now use the pci_device->revision member. This exposes some issues where drivers where reading a word or a dword for the revision number, and adding useless error-handling around the read. Some drivers even just read it for no purpose of all. In devices where the revision ID is being copied over and used in what appears to be the equivalent of hotpath, I have left the copy code and the cached copy as not to influence the driver's performance. Compile tested with make all{yes,mod}config on x86_64 and i386. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Acked-by: Dave Jones <davej@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* via82cxxx: backport short cables support from pata_via.cBartlomiej Zolnierkiewicz2007-07-091-7/+41
| | | | | | | | | Backport short cables support from pata_via.c. This patch should allow UDMA > 2 modes on Acer Ferrari 3400. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
* sis5513: backport short cables support from pata_sis.cBartlomiej Zolnierkiewicz2007-07-091-1/+24
| | | | | | | | | | | Backport short cables support from pata_sis.c. This patch allows UDMA > 2 modes on ASUS A6K. Thanks to testing this patch goes out to Jiri Stavinoha. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
* alim15x3: backport short cables support from pata_ali.cBartlomiej Zolnierkiewicz2007-07-091-23/+48
| | | | | | | | | | Backport short cables support from pata_ali.c and while at it cleanup existing cable detection code. This patch should allow UDMA > 2 modes on HP Pavilion N5430 and Fujitsu P2000. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
* piix: backport short cables support from ata_piix.cBartlomiej Zolnierkiewicz2007-07-091-3/+34
| | | | | | | | | | | | | Backport short cables support from ata_piix.c. This patch should allow UDMA > 2 modes on: - Acer 5602WLMi - Acer 3682WLMi - Asus W5F - Acer Aspire 2023WLMi Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
* ide: add short cables supportBartlomiej Zolnierkiewicz2007-07-0920-80/+104
| | | | | | | | | | | | | | | | | | | | | | This patch allows users to override both host and device side cable detection with "ideX=ata66" kernel parameter. Thanks to this it should be now possible to use UDMA > 2 modes on systems (laptops mainly) which use short 40-pin cable instead of 80-pin one. Next patches add automatic detection of some systems using short cables. Changes: * Rename hwif->udma_four to hwif->cbl and make it u8. * Convert all existing users accordingly (use ATA_CBL_* defines while at it). * Add ATA_CBL_PATA40_SHORT support to ide-iops.c:eighty_ninty_three(). * Use ATA_CBL_PATA40_SHORT for "ideX=ata66" kernel parameter. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
* ide: convert ide_find_best_mode() users to use ide_max_dma_mode()Bartlomiej Zolnierkiewicz2007-07-092-135/+115
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ide-timing.h: * remove handling of DMA modes from ide_find_best_mode() and rename it to ide_find_best_pio_mode() * drop no longer needed "map" argument from ide_find_best_pio_mode() and delete needless ->id check * remove no longer needed XFER_SWDMA and XFER_UDMA* defines au1xxx-ide.c: * use ide_max_dma_mode() instead of ide_find_best_mode() * remove needless CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA #ifdef amd74xx.c: * store UDMA masks in amd_ide_chip[] and while at it make "base" field to be u8 instead of unsigned long * convert the driver to use UDMA masks from amd_ide_chip[] * use ide_max_dma_mode() and ide_find_best_pio_mode() instead of ide_find_best_mode() * delete stale comment from amd74xx_ide_dma_check() * remove no longer needed AMD_UDMA* defines via82cxxx.c: * remove unused DISPLAY_VIA_TIMINGS define * store UDMA masks in via_isa_bridges[] and while at it make "flags" field to be u8 instead of u16 * convert the driver to use UDMA masks from via_isa_bridges[] * use ide_max_dma_mode() and ide_find_best_pio_mode() instead of ide_find_best_mode() * remove no longer needed VIA_UDMA* defines pmac.c: * use ide_max_dma_mode() instead of ide_find_best_mode() There should be no functionality changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
* aec62xx: kill speedproc() method wrapper (take 2)Sergei Shtylyov2007-07-091-20/+8
| | | | | | | | | There's no reason to have the speedproc() method wrapper for the two quite different chip families, so just get rid of it. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* aec62xx: remove init_dma() method (take 2)Sergei Shtylyov2007-07-091-35/+16
| | | | | | | | | | | | | | | | Get rid of the init_dma() method (which had no particular reason to exist) by folding it into the init_hwif() method. While at it, also perform some cleanup in the latter method: - get rid of the useless clearing of hwif->autodma; - fold the serialization code into one 'if' statement; - fold setting the drives' 'autotune' and 'autodma' fields into the single statements... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* aec62xx: rework init_setup_aec6x80()Sergei Shtylyov2007-07-091-22/+13
| | | | | | | | | | | | | | | | | | | | Rework init_setup_aec6x80() so that it won't rewrite the constant name strings anymore -- in order to do this: - in aec62xx_init_one(), pass a local copy of 'struct pci_device_id' down the call chain; - change the names for in aec62xx_chipsets[] to default to AEC-6280[R]; - override the 'name' field in init_setup_aec6x80() only if bit 4 of the DMA status register is set. While at it, also change the 'udma_mask' field for AEC-6x80R chips in this function and remove the code doing the same from the init_hwif() method... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* cmd64x: init. code cleanupSergei Shtylyov2007-07-091-81/+45
| | | | | | | | | | | | | | | | | | | | | Fix two minor issues with PCI0646 chip reporting in the init_chipset() method: "IRQ workaround enabled" message printed out not only for revision 0x01 and "CMD646: chipset revision" printed twice (by IDE core and the driver itself). Also, remove empty/pointless switch cases for the chips other than PCI0646, duplicate write to the MRDMODE register when enabling interrupts and MEMORY READ LINE cycles, and needless/misplaced initialization of the timing registers in this method. Switch to reading only the PCI revision ID register itself, not the whole 32 bits at its address in init_chipset() and init_hwif() methods; in addition, get rid of the useless clearing of hwif->autodma and perform some cosmetic style changes in the latter method. Refactor ata66_cmd64x() by moving all the code into the 'switch' statement, renaming/adding variables, and fixing the coding style. While at it, finally get rid of the meaningless aliasing register #define's... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt366: simplify UltraDMA filtering (take 4)Sergei Shtylyov2007-07-091-72/+82
| | | | | | | | | | | | | | | | | | Simplify UltraDMA mode filtering in the driver: - make use of the newly introduced 'udma_mask' field of 'ide_pci_device_t' to set the correct hwif->ultra_mask, modifying init_setup_hpt366() to select the correct mask based on the chip revision; - replace 'max_mode' field of the 'struct hpt_info' with 'max_ultra' specifying the maximum UltraDMA mode allowed; - rewrite hpt3xx_udma_filter() to differ the filters based on the 'chip_type' field, and only use it for HPT366 and HPT370[A] where it's really necessary. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: make void and rename ide_dma_timeout() methodSergei Shtylyov2007-07-094-17/+17
| | | | | | | | | | | | | | | Since ide_dma_timeout() method's result is discarded, make it return 'void'. While at it, drop 'ide_' from the method's name, drop the '__' prefix from the default method's name, and do some cleanups in this method driver-wise: - in ide-dma.c, au1xxx-ide.c, and pdc202xx_old.c, define/use 'hwif' variable; - in au1xxx-ide.c, get rid of commented out printk(); - in sl82c105.c, get rid of unnecessary variables. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: make void and rename ide_dma_lostirq() methodSergei Shtylyov2007-07-095-29/+25
| | | | | | | | | | | | | | | | Since ide_dma_lostirq() method's result is discarded, make it return 'void'. While at it, rename the method to dma_lost_irq(), drop the '__' prefix from the default method's name, and do some cleanups in this method driver-wise: - in aec62xx.c, rename the method in accordance with other drivers, and get rid of unnecessary variables there; - in pdc202xx_old.c, define/use 'hwif' variable; - in sgiioc4.c, rearrange the code to call the resetproc() method directly. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* serverworks: always tune CSB6Bartlomiej Zolnierkiewicz2007-07-091-75/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Switch the driver to always program DMA/PIO timings and set device transfer mode instead of trusting BIOS on CSB6 controllers (libata pata_serverworks.c driver is also doing things this way and there were no problems reported so far). While doing conversion I noticed that the old code had many issues: * the code was assuming that hwif->dma_status is always valid (which obviously isn't true if hwif->dma_base == NULL) * value of "(ultra_timing >> (4*unit)) & ~(0xF0)" expression wasn't checked to fit into udma_modes[5] * code validating DMA timings didn't validate corresponding PIO timings * extra CSB5 PIO register wasn't validated et all * hwif->ide_dma_off_quietly() is always called before ide_set_dma() (which in turn calls hwif->speedproc() method - svwks_tune_chipset() in this case) so the code depending on DMA capable bit of DMA status to be set was never executed (=> the code was never validating DMA timings despite actually enabling DMA if the PIO timings were OK!) * on resume driver dependend entirely on BIOS to restore timings and set transfer mode on the device While at it: There is no need to read PIO/MWDMA timings now so don't do it. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
* sis5513: adding PCI-IDUwe Koziolek2007-07-081-0/+1
| | | | | | | | | | | | | | | The SiS966 has one additional PCI-ID 1180. If the chipset is using this PCI-ID, the primary channel is connected to the first PATA-port. The secondary channel is connected to SATA-ports in IDE emulation mode. The legacy IO-ports are used. The including of the PCI-ID into pata_sis is not sufficient, because the legacy driver in drivers/ide is initialized before pata_sis. Signed-off-by: Uwe Koziolek <uwe.koziolek@gmx.net> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: pdc202xx_new PLL input clock fixAlbert Lee2007-07-031-2/+8
| | | | | | | | | | | | | | | | | Recently the PLL input clock of Promise 2027x is sometimes detected higher than expected (e.g. 20.027 MHz compared to 16.714 MHz). It seems sometimes the mdelay() function is not as precise as it used to be. Per Alan's advice, HT or power management might affect the precision of mdelay(). This patch calls gettimeofday() to measure the time elapsed and calculate the PLL input clock accordingly. Signed-off-by: Albert Lee <albertcc@tw.ibm.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Bahadir Balban <bahadir.balban@gmail.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* it821x: fix incorrect SWDMA maskBartlomiej Zolnierkiewicz2007-07-031-2/+1
| | | | | | | | | | | | | SWDMA modes are unsupported by it821x. Attempts to tune SWDMA modes always fail (due to sanity check in ->speedproc) and result in PIO being tuned. * Fix incorrect SWDMA mask so core code won't try these modes and will just tune PIO if no other DMA modes are available. * Bump driver version. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
* amd74xx: resume fixBartlomiej Zolnierkiewicz2007-07-031-5/+3
| | | | | | | | | | | | * Driver can't skip programming transfer mode on the device in amd_set_drive() (similar fix has been applied to via82cxxx driver ages ago). * While at it remove redundant warning (ide_config_drive_speed() already produces more valuable one). * Bump driver version. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt366: use correct enablebits for HPT36xSergei Shtylyov2007-07-031-5/+15
| | | | | | | | | | | | The HPT36x chips finally turned out to have the channel enable bits -- however, badly implemented. Make use of them despite it's probably only going to burden the driver's code -- assuming both channels are always enabled by the HighPoint BIOS anyway... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: Linas Vepstas <linas@austin.ibm.com> Cc: michal.kepien@poczta.onet.pl Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt366: blacklist MAXTOR STM3320620A for UltraDMA/66Sergei Shtylyov2007-07-031-1/+2
| | | | | | | | | Add the MAXTOR STM3320620A drive into the UltraDMA/66 mode blacklist for the HPT36x chips. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: Add the MCP73/77 support to PATA driverPeer Chen2007-06-081-3/+9
| | | | | | | | | | | | | | Add the MCP73/MCP77 support to PATA driver. bart: Added amd74xx_chipsets[] and amd_pci_tbl[] entries. bart: Bumped driver version. Signed-off-by: Peer Chen <peerchen@gmail.com> Cc: Alan Cox <alan@redhat.com>, Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jeff Garzik <jeff@garzik.org> Cc: Tejun Heo <htejun@gmail.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt366: disallow Ultra133 for HPT374Sergei Shtylyov2007-06-081-4/+4
| | | | | | | | | Eliminate UltraATA/133 support for HPT374 -- the chip isn't capable of this mode according to the manual, and doesn't even seem to tolerate 66 MHz DPLL clock... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Geller Sandor <wildy@petra.hos.u-szeged.hu> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: generic IDE PCI driver, add another device exceptionJiri Slaby2007-06-081-14/+23
| | | | | | | | | | | | | | | | generic IDE PCI driver, add another device exception This device is char device and is grabbed by generic ide driver: 00:0b.0 Class ffff: National Semiconductor Corporation 87410 IDE (rev ff) (prog-if ff) Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Disallow generic IDE PCI driver to grab it by adding next condition. Also consolidate exceptions to one bigger 'switch (dev->vendor)'. Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Ingo Korb <ml@akana.de> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* it821x: RAID mode fixesBartlomiej Zolnierkiewicz2007-06-081-16/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DMA support for RAID mode broke after: commit 71ef51cc1756d1c56b57c70e7cc27a3559c81ee6 Author: Jens Axboe <axboe@suse.de> Date:   Fri Jul 28 09:02:17 2006 +0200     [PATCH] it821x: fix ide dma setup bug     Only enable dma for a valid speed setting.     Signed-off-by: Jens Axboe <axboe@suse.de> commit 0a8348d08677ad77ee353f96eb8745c693a05a13 Author: Jens Axboe <axboe@suse.de> Date:   Fri Jul 28 08:58:26 2006 +0200     [PATCH] ide: if the id fields looks screwy, disable DMA     It's the safer choice. Originally due to a bug in itx821x, but a     generally sound thing to do.     Signed-off-by: Jens Axboe <axboe@suse.de> However it worked by pure luck before Jens' fixes: bogus ide_dma_enable() usage in it821x driver combined with loosy check in ide_dma_verbose() allowed the hardware to operate in DMA mode. When these problems were fixed the DMA support broke... The source root for the regression turned out to be that the it821x.c code was clearing too much of id->field_valid. The IDE core code was using the original value of id->field_valid to do the tuning but later DMA got disabled in ide_dma_verbose() because of the incorrect id->field_valid fixup. Fix it. While at it: * Do fixup() after probing the drives but before tuning them (which is also OK w.r.t. ide_undecoded_slave() fixup). This change fixes device IDENTIFY data to be consistent before/after the tuning and allows us to remove extra re-tuning of drives from it821x_fixups(). * Fake MWDMA0 enabled/supported bits in IDENTIFY data if the device has DMA capable bit set (this is just to tell the IDE core that DMA is supported since it821x firmware takes care of DMA mode programming). * Don't touch timing registers and don't program transfer modes on devices et all when in RAID mode - depend solely on firmware to do the tuning (as suggested by Alan Cox and done in libata pata_it821x driver). Thanks for testing the patch goes out to Thomas Kuther. Cc: Thomas Kuther <gimpel@sonnenkinder.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Jens Axboe <axboe@suse.de> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* serverworks: fix CSB6 tuning logicBartlomiej Zolnierkiewicz2007-06-081-13/+27
| | | | | | | | | | | | | | | | | | | | | | | | | Problem noticed by Joe Zbiciak, see http://kerneltrap.org/node/8252 for details. On CSB6 the driver is using BIOS settings and not programming DMA/PIO timings itself. However the logic was completely broken and resulted in wrong timings being silently allowed (instead of being corrected by the driver). This bug would explain some data corruption/timeout issues with Serverworks MegaIDE in RAID mode that Alan Cox has fixed recently with: http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=2074a106f52b6371885afbd714e929d60d0e3f64 For 2.6.23 we may be better off with completely switching the driver to always programming timings (libata pata_serverworks.c driver is doing things this way and there were no problems reported so far) but for 2.6.22 lets fix the bug in the simplest and the least intrusive way. Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* serverworks: remove crappy codeBartlomiej Zolnierkiewicz2007-06-081-7/+6
| | | | | | | | | | | | | | | | Remove crappy code noticed by Linus, see http://lkml.org/lkml/2007/5/23/476 for details. While at it simplify logic a bit. There should be no functionality changes caused by this patch. Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide serverworks warning fixesAndrew Morton2007-05-241-4/+4
| | | | | | | | | | | | | gcc-4.3: drivers/ide/pci/serverworks.c: In function 'svwks_tune_chipset': drivers/ide/pci/serverworks.c:176: warning: overflow in implicit constant conversion drivers/ide/pci/serverworks.c:190: warning: overflow in implicit constant conversion drivers/ide/pci/serverworks.c:211: warning: overflow in implicit constant conversion drivers/ide/pci/serverworks.c:212: warning: overflow in implicit constant conversion Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide/pci/serverworks.c: Fix corruption/timeouts with MegaIDEAlan Cox2007-05-241-0/+6
| | | | | | | | | | | | | | | | | | It turns out from customer reports to Red Hat and some PCI dumps that the MegaIDE in RAID mode doesn't provide the drive tuning data that the serverworks driver expects but sometimes does provide something that fools the code. For the RAID class case skip the oem setup and don't trust the BIOS data. We then tune from scratch and this sorts it out. (This has been confirmed on an afflicted IBM blade) [libata serverworks.c never trusts the BIOS in the first place so is accidentally immune] Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add the IDE device ID for ATI SB700Henry Su2007-05-241-0/+1
| | | | | | | | | Add the IDE device ID to atiixp_pci_tbl struct in atiixp.c for ATI SB700. From: Henry Su <henry.su@amd.com> Signed-off-by: Luugi Marsan <luugi.marsan@amd.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* sl82c105: Switch to ref counting APIAlan Cox2007-05-161-3/+5
| | | | | | | | | Not sure how this one got missed in the great purge some time ago but it did. Signed-off-by: Alan Cox <alan@redhat.com> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: remove ide_dma_enable()Bartlomiej Zolnierkiewicz2007-05-166-86/+8
| | | | | | | | * check ->speedproc return value in ide_tune_dma() * use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers * remove no longer needed ide_dma_enable() Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* sl82c105: add speedproc() method and MWDMA0/1 supportSergei Shtylyov2007-05-161-5/+66
| | | | | | | | | | | Add the speedproc() method for setting transfer modes, modify config_for_dma() to call it and use ide_max_dma_mode() to select the best DMA mode. Add support for the multiword DMA modes 0 and 1, using the upper half of the 'drive_data' field to store the DMA timings to program into the drive control register when DMA is turned on for real. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* cs5530/sc1200: add ->speedproc supportBartlomiej Zolnierkiewicz2007-05-162-46/+81
| | | | | | | | | | | * add {cs5530,sc1200}_tunepio() for programming PIO timings * add {cs5530,sc1200}_tune_chipset() (->speedproc method) for setting transfer mode and convert {cs5530,sc1200}_config_dma() to use it * bump driver version Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
generated by cgit (git 2.34.1) at 2024-10-03 21:34:15 +0000