diff options
Diffstat (limited to 'drivers/mtd/nand/omap2.c')
| -rw-r--r-- | drivers/mtd/nand/omap2.c | 253 |
1 files changed, 251 insertions, 2 deletions
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c index c2b0bba9d8b3..d7f681d0c9b9 100644 --- a/drivers/mtd/nand/omap2.c +++ b/drivers/mtd/nand/omap2.c @@ -21,6 +21,10 @@ #include <linux/io.h> #include <linux/slab.h> +#ifdef CONFIG_MTD_NAND_OMAP_BCH +#include <linux/bch.h> +#endif + #include <plat/dma.h> #include <plat/gpmc.h> #include <plat/nand.h> @@ -127,6 +131,11 @@ struct omap_nand_info { } iomode; u_char *buf; int buf_len; + +#ifdef CONFIG_MTD_NAND_OMAP_BCH + struct bch_control *bch; + struct nand_ecclayout ecclayout; +#endif }; /** @@ -402,7 +411,7 @@ static inline int omap_nand_dma_transfer(struct mtd_info *mtd, void *addr, PREFETCH_FIFOTHRESHOLD_MAX, 0x1, len, is_write); if (ret) /* PFPW engine is busy, use cpu copy method */ - goto out_copy; + goto out_copy_unmap; init_completion(&info->comp); @@ -421,6 +430,8 @@ static inline int omap_nand_dma_transfer(struct mtd_info *mtd, void *addr, dma_unmap_single(&info->pdev->dev, dma_addr, len, dir); return 0; +out_copy_unmap: + dma_unmap_single(&info->pdev->dev, dma_addr, len, dir); out_copy: if (info->nand.options & NAND_BUSWIDTH_16) is_write == 0 ? omap_read_buf16(mtd, (u_char *) addr, len) @@ -879,7 +890,7 @@ static int omap_wait(struct mtd_info *mtd, struct nand_chip *chip) struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, mtd); unsigned long timeo = jiffies; - int status = NAND_STATUS_FAIL, state = this->state; + int status, state = this->state; if (state == FL_ERASING) timeo += (HZ * 400) / 1000; @@ -894,6 +905,8 @@ static int omap_wait(struct mtd_info *mtd, struct nand_chip *chip) break; cond_resched(); } + + status = gpmc_nand_read(info->gpmc_cs, GPMC_NAND_DATA); return status; } @@ -925,6 +938,226 @@ static int omap_dev_ready(struct mtd_info *mtd) return 1; } +#ifdef CONFIG_MTD_NAND_OMAP_BCH + +/** + * omap3_enable_hwecc_bch - Program OMAP3 GPMC to perform BCH ECC correction + * @mtd: MTD device structure + * @mode: Read/Write mode + */ +static void omap3_enable_hwecc_bch(struct mtd_info *mtd, int mode) +{ + int nerrors; + unsigned int dev_width; + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); + struct nand_chip *chip = mtd->priv; + + nerrors = (info->nand.ecc.bytes == 13) ? 8 : 4; + dev_width = (chip->options & NAND_BUSWIDTH_16) ? 1 : 0; + /* + * Program GPMC to perform correction on one 512-byte sector at a time. + * Using 4 sectors at a time (i.e. ecc.size = 2048) is also possible and + * gives a slight (5%) performance gain (but requires additional code). + */ + (void)gpmc_enable_hwecc_bch(info->gpmc_cs, mode, dev_width, 1, nerrors); +} + +/** + * omap3_calculate_ecc_bch4 - Generate 7 bytes of ECC bytes + * @mtd: MTD device structure + * @dat: The pointer to data on which ecc is computed + * @ecc_code: The ecc_code buffer + */ +static int omap3_calculate_ecc_bch4(struct mtd_info *mtd, const u_char *dat, + u_char *ecc_code) +{ + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); + return gpmc_calculate_ecc_bch4(info->gpmc_cs, dat, ecc_code); +} + +/** + * omap3_calculate_ecc_bch8 - Generate 13 bytes of ECC bytes + * @mtd: MTD device structure + * @dat: The pointer to data on which ecc is computed + * @ecc_code: The ecc_code buffer + */ +static int omap3_calculate_ecc_bch8(struct mtd_info *mtd, const u_char *dat, + u_char *ecc_code) +{ + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); + return gpmc_calculate_ecc_bch8(info->gpmc_cs, dat, ecc_code); +} + +/** + * omap3_correct_data_bch - Decode received data and correct errors + * @mtd: MTD device structure + * @data: page data + * @read_ecc: ecc read from nand flash + * @calc_ecc: ecc read from HW ECC registers + */ +static int omap3_correct_data_bch(struct mtd_info *mtd, u_char *data, + u_char *read_ecc, u_char *calc_ecc) +{ + int i, count; + /* cannot correct more than 8 errors */ + unsigned int errloc[8]; + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); + + count = decode_bch(info->bch, NULL, 512, read_ecc, calc_ecc, NULL, + errloc); + if (count > 0) { + /* correct errors */ + for (i = 0; i < count; i++) { + /* correct data only, not ecc bytes */ + if (errloc[i] < 8*512) + data[errloc[i]/8] ^= 1 << (errloc[i] & 7); + pr_debug("corrected bitflip %u\n", errloc[i]); + } + } else if (count < 0) { + pr_err("ecc unrecoverable error\n"); + } + return count; +} + +/** + * omap3_free_bch - Release BCH ecc resources + * @mtd: MTD device structure + */ +static void omap3_free_bch(struct mtd_info *mtd) +{ + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); + if (info->bch) { + free_bch(info->bch); + info->bch = NULL; + } +} + +/** + * omap3_init_bch - Initialize BCH ECC + * @mtd: MTD device structure + * @ecc_opt: OMAP ECC mode (OMAP_ECC_BCH4_CODE_HW or OMAP_ECC_BCH8_CODE_HW) + */ +static int omap3_init_bch(struct mtd_info *mtd, int ecc_opt) +{ + int ret, max_errors; + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); +#ifdef CONFIG_MTD_NAND_OMAP_BCH8 + const int hw_errors = 8; +#else + const int hw_errors = 4; +#endif + info->bch = NULL; + + max_errors = (ecc_opt == OMAP_ECC_BCH8_CODE_HW) ? 8 : 4; + if (max_errors != hw_errors) { + pr_err("cannot configure %d-bit BCH ecc, only %d-bit supported", + max_errors, hw_errors); + goto fail; + } + + /* initialize GPMC BCH engine */ + ret = gpmc_init_hwecc_bch(info->gpmc_cs, 1, max_errors); + if (ret) + goto fail; + + /* software bch library is only used to detect and locate errors */ + info->bch = init_bch(13, max_errors, 0x201b /* hw polynomial */); + if (!info->bch) + goto fail; + + info->nand.ecc.size = 512; + info->nand.ecc.hwctl = omap3_enable_hwecc_bch; + info->nand.ecc.correct = omap3_correct_data_bch; + info->nand.ecc.mode = NAND_ECC_HW; + + /* + * The number of corrected errors in an ecc block that will trigger + * block scrubbing defaults to the ecc strength (4 or 8). + * Set mtd->bitflip_threshold here to define a custom threshold. + */ + + if (max_errors == 8) { + info->nand.ecc.strength = 8; + info->nand.ecc.bytes = 13; + info->nand.ecc.calculate = omap3_calculate_ecc_bch8; + } else { + info->nand.ecc.strength = 4; + info->nand.ecc.bytes = 7; + info->nand.ecc.calculate = omap3_calculate_ecc_bch4; + } + + pr_info("enabling NAND BCH ecc with %d-bit correction\n", max_errors); + return 0; +fail: + omap3_free_bch(mtd); + return -1; +} + +/** + * omap3_init_bch_tail - Build an oob layout for BCH ECC correction. + * @mtd: MTD device structure + */ +static int omap3_init_bch_tail(struct mtd_info *mtd) +{ + int i, steps; + struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, + mtd); + struct nand_ecclayout *layout = &info->ecclayout; + + /* build oob layout */ + steps = mtd->writesize/info->nand.ecc.size; + layout->eccbytes = steps*info->nand.ecc.bytes; + + /* do not bother creating special oob layouts for small page devices */ + if (mtd->oobsize < 64) { + pr_err("BCH ecc is not supported on small page devices\n"); + goto fail; + } + + /* reserve 2 bytes for bad block marker */ + if (layout->eccbytes+2 > mtd->oobsize) { + pr_err("no oob layout available for oobsize %d eccbytes %u\n", + mtd->oobsize, layout->eccbytes); + goto fail; + } + + /* put ecc bytes at oob tail */ + for (i = 0; i < layout->eccbytes; i++) + layout->eccpos[i] = mtd->oobsize-layout->eccbytes+i; + + layout->oobfree[0].offset = 2; + layout->oobfree[0].length = mtd->oobsize-2-layout->eccbytes; + info->nand.ecc.layout = layout; + + if (!(info->nand.options & NAND_BUSWIDTH_16)) + info->nand.badblock_pattern = &bb_descrip_flashbased; + return 0; +fail: + omap3_free_bch(mtd); + return -1; +} + +#else +static int omap3_init_bch(struct mtd_info *mtd, int ecc_opt) +{ + pr_err("CONFIG_MTD_NAND_OMAP_BCH is not enabled\n"); + return -1; +} +static int omap3_init_bch_tail(struct mtd_info *mtd) +{ + return -1; +} +static void omap3_free_bch(struct mtd_info *mtd) +{ +} +#endif /* CONFIG_MTD_NAND_OMAP_BCH */ + static int __devinit omap_nand_probe(struct platform_device *pdev) { struct omap_nand_info *info; @@ -1063,6 +1296,13 @@ static int __devinit omap_nand_probe(struct platform_device *pdev) info->nand.ecc.hwctl = omap_enable_hwecc; info->nand.ecc.correct = omap_correct_data; info->nand.ecc.mode = NAND_ECC_HW; + } else if ((pdata->ecc_opt == OMAP_ECC_BCH4_CODE_HW) || + (pdata->ecc_opt == OMAP_ECC_BCH8_CODE_HW)) { + err = omap3_init_bch(&info->mtd, pdata->ecc_opt); + if (err) { + err = -EINVAL; + goto out_release_mem_region; + } } /* DIP switches on some boards change between 8 and 16 bit @@ -1094,6 +1334,14 @@ static int __devinit omap_nand_probe(struct platform_device *pdev) (offset + omap_oobinfo.eccbytes); info->nand.ecc.layout = &omap_oobinfo; + } else if ((pdata->ecc_opt == OMAP_ECC_BCH4_CODE_HW) || + (pdata->ecc_opt == OMAP_ECC_BCH8_CODE_HW)) { + /* build OOB layout for BCH ECC correction */ + err = omap3_init_bch_tail(&info->mtd); + if (err) { + err = -EINVAL; + goto out_release_mem_region; + } } /* second phase scan */ @@ -1122,6 +1370,7 @@ static int omap_nand_remove(struct platform_device *pdev) struct mtd_info *mtd = platform_get_drvdata(pdev); struct omap_nand_info *info = container_of(mtd, struct omap_nand_info, mtd); + omap3_free_bch(&info->mtd); platform_set_drvdata(pdev, NULL); if (info->dma_ch != -1) |