diff options
| -rw-r--r-- | Documentation/devicetree/bindings/i2c/samsung-i2c.txt | 8 | ||||
| -rw-r--r-- | drivers/i2c/busses/i2c-s3c2410.c | 30 |
2 files changed, 36 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt index 38832c712919..b6cb5a12c672 100644 --- a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt @@ -6,14 +6,18 @@ Required properties: - compatible: value should be either of the following. (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c. (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c. + (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used + inside HDMIPHY block found on several samsung SoCs - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt number to the cpu. - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges. - - gpios: The order of the gpios should be the following: <SDA, SCL>. - The gpio specifier depends on the gpio controller. Optional properties: + - gpios: The order of the gpios should be the following: <SDA, SCL>. + The gpio specifier depends on the gpio controller. Required in all + cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output + lines are permanently wired to the respective client - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not specified, default value is 0. - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c index 23736ffaaa2a..fa0b13490873 100644 --- a/drivers/i2c/busses/i2c-s3c2410.c +++ b/drivers/i2c/busses/i2c-s3c2410.c @@ -46,6 +46,8 @@ /* Treat S3C2410 as baseline hardware, anything else is supported via quirks */ #define QUIRK_S3C2440 (1 << 0) +#define QUIRK_HDMIPHY (1 << 1) +#define QUIRK_NO_GPIO (1 << 2) /* i2c controller state */ enum s3c24xx_i2c_state { @@ -93,6 +95,9 @@ static struct platform_device_id s3c24xx_driver_ids[] = { }, { .name = "s3c2440-i2c", .driver_data = QUIRK_S3C2440, + }, { + .name = "s3c2440-hdmiphy-i2c", + .driver_data = QUIRK_S3C2440 | QUIRK_HDMIPHY | QUIRK_NO_GPIO, }, { }, }; MODULE_DEVICE_TABLE(platform, s3c24xx_driver_ids); @@ -101,6 +106,8 @@ MODULE_DEVICE_TABLE(platform, s3c24xx_driver_ids); static const struct of_device_id s3c24xx_i2c_match[] = { { .compatible = "samsung,s3c2410-i2c", .data = (void *)0 }, { .compatible = "samsung,s3c2440-i2c", .data = (void *)QUIRK_S3C2440 }, + { .compatible = "samsung,s3c2440-hdmiphy-i2c", + .data = (void *)(QUIRK_S3C2440 | QUIRK_HDMIPHY | QUIRK_NO_GPIO) }, {}, }; MODULE_DEVICE_TABLE(of, s3c24xx_i2c_match); @@ -483,6 +490,13 @@ static int s3c24xx_i2c_set_master(struct s3c24xx_i2c *i2c) unsigned long iicstat; int timeout = 400; + /* the timeout for HDMIPHY is reduced to 10 ms because + * the hangup is expected to happen, so waiting 400 ms + * causes only unnecessary system hangup + */ + if (i2c->quirks & QUIRK_HDMIPHY) + timeout = 10; + while (timeout-- > 0) { iicstat = readl(i2c->regs + S3C2410_IICSTAT); @@ -492,6 +506,15 @@ static int s3c24xx_i2c_set_master(struct s3c24xx_i2c *i2c) msleep(1); } + /* hang-up of bus dedicated for HDMIPHY occurred, resetting */ + if (i2c->quirks & QUIRK_HDMIPHY) { + writel(0, i2c->regs + S3C2410_IICCON); + writel(0, i2c->regs + S3C2410_IICSTAT); + writel(0, i2c->regs + S3C2410_IICDS); + + return 0; + } + return -ETIMEDOUT; } @@ -773,6 +796,9 @@ static int s3c24xx_i2c_parse_dt_gpio(struct s3c24xx_i2c *i2c) { int idx, gpio, ret; + if (i2c->quirks & QUIRK_NO_GPIO) + return 0; + for (idx = 0; idx < 2; idx++) { gpio = of_get_gpio(i2c->dev->of_node, idx); if (!gpio_is_valid(gpio)) { @@ -797,6 +823,10 @@ free_gpio: static void s3c24xx_i2c_dt_gpio_free(struct s3c24xx_i2c *i2c) { unsigned int idx; + + if (i2c->quirks & QUIRK_NO_GPIO) + return; + for (idx = 0; idx < 2; idx++) gpio_free(i2c->gpios[idx]); } |