diff options
Diffstat (limited to 'base/tks/shared/conf/workers.properties')
| -rw-r--r-- | base/tks/shared/conf/workers.properties | 211 |
1 files changed, 211 insertions, 0 deletions
diff --git a/base/tks/shared/conf/workers.properties b/base/tks/shared/conf/workers.properties new file mode 100644 index 000000000..2c39c6402 --- /dev/null +++ b/base/tks/shared/conf/workers.properties @@ -0,0 +1,211 @@ +# --- BEGIN COPYRIGHT BLOCK --- +# Copyright (C) 2006 Red Hat, Inc. +# All rights reserved. +# --- END COPYRIGHT BLOCK --- +# +# workers.properties - +# +# This file provides jk derived plugins with the needed information to +# connect to the different tomcat workers. Note that the distributed +# version of this file requires modification before it is usable by a +# plugin. +# +# As a general note, the characters $( and ) are used internally to define +# macros. Do not use them in your own configuration!!! +# +# Whenever you see a set of lines such as: +# x=value +# y=$(x)\something +# +# the final value for y will be value\something +# +# Normaly all you will need to do is un-comment and modify the first three +# properties, i.e. workers.tomcat_home, workers.java_home and ps. +# Most of the configuration is derived from these. +# +# When you are done updating workers.tomcat_home, workers.java_home and ps +# you should have 3 workers configured: +# +# - An ajp12 worker that connects to localhost:8007 +# - An ajp13 worker that connects to localhost:8009 +# - A jni inprocess worker. +# - A load balancer worker +# +# However by default the plugins will only use the ajp12 worker. To have +# the plugins use other workers you should modify the worker.list property. +# +# + +# OPTIONS ( very important for jni mode ) + +# +# workers.tomcat_home should point to the location where you +# installed tomcat. This is where you have your conf, webapps and lib +# directories. +# +workers.tomcat_home=/var/tomcat3 + +# +# workers.java_home should point to your Java installation. Normally +# you should have a bin and lib directories beneath it. +# +workers.java_home=/opt/IBMJava2-13 + +# +# You should configure your environment slash... ps=\ on NT and / on UNIX +# and maybe something different elsewhere. +# +ps=/ + +# +#------ ADVANCED MODE ------------------------------------------------ +#--------------------------------------------------------------------- +# + +# +#------ DEFAULT worket list ------------------------------------------ +#--------------------------------------------------------------------- +# +# +# The workers that your plugins should create and work with +# +# Add 'inprocess' if you want JNI connector +worker.list=ajp12, ajp13 +# , inprocess + + +# +#------ DEFAULT ajp12 WORKER DEFINITION ------------------------------ +#--------------------------------------------------------------------- +# + +# +# Defining a worker named ajp12 and of type ajp12 +# Note that the name and the type do not have to match. +# +worker.ajp12.port=8007 +worker.ajp12.host=localhost +worker.ajp12.type=ajp12 +# +# Specifies the load balance factor when used with +# a load balancing worker. +# Note: +# ----> lbfactor must be > 0 +# ----> Low lbfactor means less work done by the worker. +worker.ajp12.lbfactor=1 + +# +#------ DEFAULT ajp13 WORKER DEFINITION ------------------------------ +#--------------------------------------------------------------------- +# + +# +# Defining a worker named ajp13 and of type ajp13 +# Note that the name and the type do not have to match. +# +worker.ajp13.port=8009 +worker.ajp13.host=localhost +worker.ajp13.type=ajp13 +# +# Specifies the load balance factor when used with +# a load balancing worker. +# Note: +# ----> lbfactor must be > 0 +# ----> Low lbfactor means less work done by the worker. +worker.ajp13.lbfactor=1 + +# +# Specify the size of the open connection cache. +#worker.ajp13.cachesize + +# +#------ DEFAULT LOAD BALANCER WORKER DEFINITION ---------------------- +#--------------------------------------------------------------------- +# + +# +# The loadbalancer (type lb) workers perform wighted round-robin +# load balancing with sticky sessions. +# Note: +# ----> If a worker dies, the load balancer will check its state +# once in a while. Until then all work is redirected to peer +# workers. +worker.loadbalancer.type=lb +worker.loadbalancer.balanced_workers=ajp12, ajp13 + + +# +#------ DEFAULT JNI WORKER DEFINITION--------------------------------- +#--------------------------------------------------------------------- +# + +# +# Defining a worker named inprocess and of type jni +# Note that the name and the type do not have to match. +# +worker.inprocess.type=jni + +# +#------ CLASSPATH DEFINITION ----------------------------------------- +#--------------------------------------------------------------------- +# + +# +# Additional class path components. +# +worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)tomcat.jar + +# +# Setting the command line for tomcat. +# Note: The cmd_line string may not contain spaces. +# +worker.inprocess.cmd_line=start + +# Not needed, but can be customized. +#worker.inprocess.cmd_line=-config +#worker.inprocess.cmd_line=$(workers.tomcat_home)$(ps)conf$(ps)server.xml +#worker.inprocess.cmd_line=-home +#worker.inprocess.cmd_line=$(workers.tomcat_home) + +# +# The JVM that we are about to use +# +# This is for Java2 +# +# Windows +worker.inprocess.jvm_lib=$(workers.java_home)$(ps)jre$(ps)bin$(ps)classic$(ps)jvm.dll +# IBM JDK1.3 +#worker.inprocess.jvm_lib=$(workers.java_home)$(ps)jre$(ps)bin$(ps)classic$(ps)libjvm.so +# Unix - Sun VM or blackdown +#worker.inprocess.jvm_lib=$(workers.java_home)$(ps)jre$(ps)lib$(ps)i386$(ps)classic$(ps)libjvm.so + +# +# And this is for jdk1.1.X +# +#worker.inprocess.jvm_lib=$(workers.java_home)$(ps)bin$(ps)javai.dll + + +# +# Setting the place for the stdout and stderr of tomcat +# +worker.inprocess.stdout=$(workers.tomcat_home)$(ps)logs$(ps)inprocess.stdout +worker.inprocess.stderr=$(workers.tomcat_home)$(ps)logs$(ps)inprocess.stderr + +# +# Setting the tomcat.home Java property +# +#worker.inprocess.sysprops=tomcat.home=$(workers.tomcat_home) + +# +# Java system properties +# +# worker.inprocess.sysprops=java.compiler=NONE +# worker.inprocess.sysprops=myprop=mypropvalue + +# +# Additional path components. +# +# worker.inprocess.ld_path=d:$(ps)SQLLIB$(ps)bin +# + + |