1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
|
Freescale MCF52277EVB ColdFire Development Board
================================================
TsiChung Liew(Tsi-Chung.Liew@freescale.com)
Created Jan 8, 2008
===========================================
Changed files:
==============
- board/freescale/m52277evb/m52277evb.c Dram setup
- board/freescale/m52277evb/Makefile Makefile
- board/freescale/m52277evb/config.mk config make
- board/freescale/m52277evb/u-boot.lds Linker description
- cpu/mcf5227x/cpu.c cpu specific code
- cpu/mcf5227x/cpu_init.c FBCS, Mux pins, icache and RTC extra regs
- cpu/mcf5227x/interrupts.c cpu specific interrupt support
- cpu/mcf5227x/speed.c system, flexbus, and cpu clock
- cpu/mcf5227x/Makefile Makefile
- cpu/mcf5227x/config.mk config make
- cpu/mcf5227x/start.S start up assembly code
- doc/README.m52277evb This readme file
- drivers/serial/mcfuart.c ColdFire common UART driver
- drivers/rtc/mcfrtc.c Realtime clock Driver
- include/asm-m68k/bitops.h Bit operation function export
- include/asm-m68k/byteorder.h Byte order functions
- include/asm-m68k/crossbar.h CrossBar structure and definition
- include/asm-m68k/dspi.h DSPI structure and definition
- include/asm-m68k/edma.h eDMA structure and definition
- include/asm-m68k/flexbus.h FlexBus structure and definition
- include/asm-m68k/fsl_i2c.h I2C structure and definition
- include/asm-m68k/global_data.h Global data structure
- include/asm-m68k/immap.h ColdFire specific header file and driver macros
- include/asm-m68k/immap_5227x.h mcf5227x specific header file
- include/asm-m68k/io.h io functions
- include/asm-m68k/lcd.h LCD structure and definition
- include/asm-m68k/m5227x.h mcf5227x specific header file
- include/asm-m68k/posix_types.h Posix
- include/asm-m68k/processor.h header file
- include/asm-m68k/ptrace.h Exception structure
- include/asm-m68k/rtc.h Realtime clock header file
- include/asm-m68k/ssi.h SSI structure and definition
- include/asm-m68k/string.h String function export
- include/asm-m68k/timer.h Timer structure and definition
- include/asm-m68k/types.h Data types definition
- include/asm-m68k/uart.h Uart structure and definition
- include/asm-m68k/u-boot.h u-boot structure
- include/configs/M52277EVB.h Board specific configuration file
- arch/m68k/lib/board.c board init function
- arch/m68k/lib/cache.c
- arch/m68k/lib/interrupts Coldfire common interrupt functions
- arch/m68k/lib/m68k_linux.c
- arch/m68k/lib/time.c Timer functions (Dma timer and PIT)
- arch/m68k/lib/traps.c Exception init code
1 MCF52277 specific Options/Settings
====================================
1.1 pre-loader is no longer suppoer in this coldfire family
1.2 Configuration settings for M52277EVB Development Board
CONFIG_MCF5227x -- define for all MCF5227x CPUs
CONFIG_M52277 -- define for all Freescale MCF52277 CPUs
CONFIG_M52277EVB -- define for M52277EVB board
CONFIG_MCFUART -- define to use common CF Uart driver
CONFIG_SYS_UART_PORT -- define UART port number, start with 0, 1 and 2
CONFIG_BAUDRATE -- define UART baudrate
CONFIG_MCFRTC -- define to use common CF RTC driver
CONFIG_SYS_MCFRTC_BASE -- provide base address for RTC in immap.h
CONFIG_SYS_RTC_OSCILLATOR -- define RTC clock frequency
RTC_DEBUG -- define to show RTC debug message
CONFIG_CMD_DATE -- enable to use date feature in u-boot
CONFIG_MCFTMR -- define to use DMA timer
CONFIG_MCFPIT -- define to use PIT timer
CONFIG_FSL_I2C -- define to use FSL common I2C driver
CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SOFT_I2C -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset
CONFIG_SYS_IMMR -- define for MBAR offset
CONFIG_SYS_MBAR -- define MBAR offset
CONFIG_MONITOR_IS_IN_RAM -- Not support
CONFIG_SYS_INIT_RAM_ADDR -- defines the base address of the MCF52277 internal SRAM
CONFIG_SYS_CSn_BASE -- defines the Chip Select Base register
CONFIG_SYS_CSn_MASK -- defines the Chip Select Mask register
CONFIG_SYS_CSn_CTRL -- defines the Chip Select Control register
CONFIG_SYS_SDRAM_BASE -- defines the DRAM Base
CONFIG_LCD and CONFIG_CMD_USB are not supported in this current u-boot,
update will be provided at later time
2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL
===========================================
2.1. System memory map:
Flash: 0x00000000-0x3FFFFFFF (1024MB)
DDR: 0x40000000-0x7FFFFFFF (1024MB)
SRAM: 0x80000000-0x8FFFFFFF (256MB)
IP: 0xF0000000-0xFFFFFFFF (256MB)
2.2. For the initial bringup, we adopted a consistent memory scheme between u-boot and
linux kernel, you can customize it based on your system requirements:
Flash0: 0x00000000-0x00FFFFFF (16MB)
DDR: 0x40000000-0x4FFFFFFF (64MB)
SRAM: 0x80000000-0x80007FFF (32KB)
IP: 0xFC000000-0xFC0FFFFF (64KB)
3. COMPILATION
==============
3.1 To create U-Boot the gcc-4.1-xx compiler set (ColdFire ELF or
uClinux version) from codesourcery.com was used. Download it from:
http://www.codesourcery.com/gnu_toolchains/coldfire/download.html
3.2 Compilation
export CROSS_COMPILE=cross-compile-prefix
cd u-boot-1.x.x
make distclean
make M52277EVB_config
make
4. SCREEN DUMP
==============
4.1 M52277EVB Development board
(NOTE: May not show exactly the same)
U-Boot 1.3.1 (Jan 8 2008 - 12:44:08)
CPU: Freescale MCF52277 (Mask:6c Version:0)
CPU CLK 160 Mhz BUS CLK 80 Mhz FLB CLK 80 MHZ
INP CLK 16 Mhz VCO CLK 480 Mhz
Board: Freescale 52277 EVB
I2C: ready
DRAM: 64 MB
FLASH: 16 MB
In: serial
Out: serial
Err: serial
-> print
baudrate=115200
hostname=M52277EVB
inpclk=16000000
loadaddr=(0x40000000 + 0x10000)
load=tftp ${loadaddr) ${u-boot}
upd=run load; run prog
prog=prot off 0 3ffff;era 0 3ffff;cp.b ${loadaddr} 0 ${filesize};save
u-boot=u-boot.bin
stdin=serial
stdout=serial
stderr=serial
mem=65024k
Environment size: 280/32764 bytes
-> bdinfo
memstart = 0x40000000
memsize = 0x04000000
flashstart = 0x00000000
flashsize = 0x01000000
flashoffset = 0x00000000
sramstart = 0x80000000
sramsize = 0x00008000
mbar = 0xFC000000
busfreq = 80 MHz
flbfreq = 80 Mhz
inpfreq = 16 Mhz
vcofreq = 480 Mhz
baudrate = 115200 bps
->
-> help
? - alias for 'help'
base - print or set address offset
bdinfo - print Board Info structure
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
date - get/set/reset date & time
dcache - enable or disable data cache
echo - echo args to console
erase - erase FLASH memory
flinfo - print FLASH memory information
go - start application at address 'addr'
help - print online help
i2c - I2C sub-system
icache - enable or disable instruction cache
iminfo - print header information for application image
imls - list all images found in flash
itest - return true/false on integer compare
loadb - load binary file over serial line (kermit mode)
loads - load S-Record file over serial line
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
ls - list files in a directory (default /)
md - memory display
mm - memory modify (auto-incrementing)
mtest - simple RAM test
mw - memory write (fill)
nm - memory modify (constant address)
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv - set environment variables
sleep - delay execution for some time
source - run script from memory
version - print monitor version
->
|
