/* * (C) Copyright 2001 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * board/config.h - configuration options, board specific */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options * (easy to change) */ #define CONFIG_405GP 1 /* This is a PPC405 CPU */ #define CONFIG_4xx 1 /* ...member of PPC4xx family */ #define CONFIG_ERIC 1 /* ...on a ERIC board */ #define CONFIG_SYS_TEXT_BASE 0xFFFC0000 #define CONFIG_BOARD_EARLY_INIT_F 1 /* run board_early_init_f() */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ #if 1 #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ #endif #if 0 #define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ #endif #if 0 #define CONFIG_ENV_IS_IN_EEPROM 1 /* use I2C RTC X1240 for environment vars */ #define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ #define CONFIG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars */ #endif /* total size of a X1240 is 2048 bytes */ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 /* X1240 has two I2C slave addresses, one for EEPROM */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* address length for the eeprom */ #define CONFIG_I2C_RTC 1 /* we have a Xicor X1240 RTC */ #define CONFIG_SYS_I2C_RTC_ADDR 0x6F /* and one for RTC */ #ifdef CONFIG_ENV_IS_IN_FLASH #undef CONFIG_ENV_IS_IN_NVRAM #undef CONFIG_ENV_IS_IN_EEPROM #else #ifdef CONFIG_ENV_IS_IN_NVRAM #undef CONFIG_ENV_IS_IN_FLASH #undef CONFIG_ENV_IS_IN_EEPROM #else #ifdef CONFIG_ENV_IS_IN_EEPROM #undef CONFIG_ENV_IS_IN_NVRAM #undef CONFIG_ENV_IS_IN_FLASH #endif #endif #endif #define CONFIG_BAUDRATE 115200 #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ #if 1 #define CONFIG_BOOTCOMMAND "bootm ffc00000" /* autoboot command */ #else #define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ #endif #define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/nfs " \ "nfsroot=192.168.1.2:/eric_root_devel " \ "ip=192.168.1.22:192.168.1.2" #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_PPC4xx_EMAC #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address */ #define CONFIG_NET_MULTI /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME /* * Command line configuration. */ #include #define CONFIG_CMD_PCI #define CONFIG_CMD_IRQ #define CONFIG_CMD_SAVEENV #define CONFIG_CMD_FLASH #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * Miscellaneous configurable options */ #undef CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CONFIG_CONS_INDEX 1 #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_serial_clock() #define CONFIG_SYS_EXT_SERIAL_CLOCK 14318180 /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ 57600, 115200, 230400, 460800, 921600 } #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ #define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- */ #define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ #define PCI_HOST_FORCE 1 /* configure as pci host */ #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ #undef CONFIG_PCI_PNP /* no pci plug-and-play */ /* resource configuration */ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1743 /* PCI Vendor ID: Peppercon AG */ #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: 405GP */ #define CONFIG_SYS_PCI_PTM1LA 0xFFFC0000 /* point to flash */ #define CONFIG_SYS_PCI_PTM1MS 0xFFFFF001 /* 4kB, enable hard-wired to 1 */ #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ #define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ #define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ #define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ /*----------------------------------------------------------------------- * External peripheral base address *----------------------------------------------------------------------- */ /* Bank 0 - Flash/SRAM 0xFF000000 16MB 16 Bit */ /* Bank 1 - NVRAM/RTC 0xF0000000 1MB 8 Bit */ /* Bank 2 - A/D converter 0xF0100000 1MB 8 Bit */ /* Bank 3 - Ethernet PHY Reset 0xF0200000 1MB 8 Bit */ /* Bank 4 - PC-MIP PRSNT1# 0xF0300000 1MB 8 Bit */ /* Bank 5 - PC-MIP PRSNT2# 0xF0400000 1MB 8 Bit */ /* Bank 6 - CPU LED0 0xF0500000 1MB 8 Bit */ /* Bank 7 - CPU LED1 0xF0600000 1MB 8 Bit */ /* ----------------------------------------------------------------------- */ /* Memory Bank 0 (Flash) initialization */ /* ----------------------------------------------------------------------- */ #define CS0_AP 0x9B015480 #define CS0_CR 0xFF87A000 /* BAS=0xFF8,BS=(8MB),BU=0x3(R/W), BW=(16 bits) */ /* ----------------------------------------------------------------------- */ /* Memory Bank 1 (NVRAM/RTC) initialization */ /* ----------------------------------------------------------------------- */ #define CS1_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */ #define CS1_CR 0xF0018000 /* BAS=0xF00,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */ /* ----------------------------------------------------------------------- */ /* Memory Bank 2 (A/D converter) initialization */ /* ----------------------------------------------------------------------- */ #define CS2_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */ #define CS2_CR 0xF0118000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */ /* ----------------------------------------------------------------------- */ /* Memory Bank 3 (Ethernet PHY Reset) initialization */ /* ----------------------------------------------------------------------- */ #define CS3_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */ #define CS3_CR 0xF0218000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */ /* ----------------------------------------------------------------------- */ /* Memory Bank 4 (PC-MIP PRSNT1#) initialization */ /* ----------------------------------------------------------------------- */ #define CS4_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */ #define CS4_CR 0xF0318000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */ /* ----------------------------------------------------------------------- */ /* Memory Bank 5 (PC-MIP PRSNT2#) initialization */ /* ----------------------------------------------------------------------- */ #define CS5_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */ #define CS5_CR 0xF0418000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */ /* ----------------------------------------------------------------------- */ /* Memory Bank 6 (CPU LED0) initialization */ /* ----------------------------------------------------------------------- */ #define CS6_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */ #define CS6_CR 0xF0518000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */ /* ----------------------------------------------------------------------- */ /* Memory Bank 7 (CPU LED1) initialization */ /* ----------------------------------------------------------------------- */ #define CS7_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */ #define CS7_CR 0xF0618000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */ #define CONFIG_SYS_NVRAM_REG_BASE_ADDR 0xF0000000 #define CONFIG_SYS_RTC_REG_BASE_ADDR (0xF0000000 + 0x7F8) #define CONFIG_SYS_ADC_REG_BASE_ADDR 0xF0100000 #define CONFIG_SYS_PHYRES_REG_BASE_ADDR 0xF0200000 #define CONFIG_SYS_PRSNT1_REG_BASE_ADDR 0xF0300000 #define CONFIG_SYS_PRSNT2_REG_BASE_ADDR 0xF0400000 #define CONFIG_SYS_LED0_REG_BASE_ADDR 0xF0500000 #define CONFIG_SYS_LED1_REG_BASE_ADDR 0xF0600000 /* SDRAM CONFIG */ #define CONFIG_SYS_SDRAM_MANUALLY 1 #define CONFIG_SYS_SDRAM_SINGLE_BANK 1 #ifdef CONFIG_SYS_SDRAM_MANUALLY /*----------------------------------------------------------------------- * Set MB0CF for bank 0. (0-32MB) Address Mode 4 since 12x8(2) *----------------------------------------------------------------------*/ #define MB0CF 0x00062001 /* 32MB @ 0 */ /*----------------------------------------------------------------------- * Set MB1CF for bank 1. (32MB-64MB) Address Mode 4 since 12x8(2) *----------------------------------------------------------------------*/ #ifdef CONFIG_SYS_SDRAM_SINGLE_BANK #define MB1CF 0x0 /* 0MB @ 32MB */ #else #define MB1CF 0x02062001 /* 32MB @ 32MB */ #endif /*----------------------------------------------------------------------- * Set MB2CF for bank 2. off *----------------------------------------------------------------------*/ #define MB2CF 0x0 /* 0MB */ /*----------------------------------------------------------------------- * Set MB3CF for bank 3. off *----------------------------------------------------------------------*/ #define MB3CF 0x0 /* 0MB */ #define SDTR_100 0x0086400D #define RTR_100 0x05F0 #define SDTR_66 0x00854006 /* orig U-Boot-wallnut says 0x00854006 */ #define RTR_66 0x03f8 #endif /* CONFIG_SYS_SDRAM_MANUALLY */ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_SDRAM_SIZE 32 #define CONFIG_SYS_FLASH_BASE 0xFF800000 /* 8 MByte Flash */ #define CONFIG_SYS_MONITOR_BASE 0xFFFE0000 /* last 128kByte within Flash */ /*#define CONFIG_SYS_MONITOR_LEN (192 * 1024)*/ /* Reserve 196 kB for Monitor */ #define CONFIG_SYS_MONITOR_LEN (128 * 1024) /* Reserve 128 kB for Monitor */ #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_16BIT 1 /* Rom 16 bit data bus */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ /* BEG ENVIRONNEMENT FLASH */ #ifdef CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_SECT_SIZE (128*1024) #if 0 /* force ENV to be NOT embedded */ #define CONFIG_ENV_ADDR 0xfffa0000 #else /* force ENV to be embedded */ #define CONFIG_ENV_SIZE (2 * 1024) /* Total Size of Environment Sector 2k */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SIZE - 0x10) /* let space for reset vector */ /* #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE)*/ #define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) #endif #endif /* END ENVIRONNEMENT FLASH */ /*----------------------------------------------------------------------- * NVRAM organization */ #define CONFIG_SYS_NVRAM_BASE_ADDR CONFIG_SYS_NVRAM_REG_BASE_ADDR /* NVRAM base address */ #define CONFIG_SYS_NVRAM_SIZE 0x7F8 /* NVRAM size 2kByte - 8 Byte for RTC */ #ifdef CONFIG_ENV_IS_IN_NVRAM #define CONFIG_ENV_SIZE 0x7F8 /* Size of Environment vars */ #define CONFIG_ENV_ADDR \ (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */ #endif /* * Init Memory Controller: * * BR0/1 and OR0/1 (FLASH) */ #define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 8MB */ #define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ /* Configuration Port location */ /* #define CONFIG_PORT_ADDR 0xF0000500 */ /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ #define CONFIG_SYS_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */ #define CONFIG_SYS_INIT_RAM_SIZE 0x0f00 /* Size of used area in RAM */ #define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Definitions for Serial Presence Detect EEPROM address * (to get SDRAM settings) */ #define SPD_EEPROM_ADDRESS 0x50 #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif #endif /* __CONFIG_H */