From 9ef57bbee1c67cc01da2026c242c4692db32be36 Mon Sep 17 00:00:00 2001 From: Martin Krause Date: Wed, 26 Sep 2007 17:55:55 +0200 Subject: TQM866M: adjust for doubled flash sector size. Adjust flash map to support the new S29GLxxN (N-Type) Flashes with doubled sector size. Signed-off-by: Martin Krause --- include/configs/TQM866M.h | 13 +++++++++---- 1 file changed, 9 insertions(+), 4 deletions(-) (limited to 'include') diff --git a/include/configs/TQM866M.h b/include/configs/TQM866M.h index 0d778919a2..76facc4295 100644 --- a/include/configs/TQM866M.h +++ b/include/configs/TQM866M.h @@ -81,9 +81,14 @@ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "rootpath=/opt/eldk/ppc_8xx\0" \ "bootfile=/tftpboot/TQM866M/uImage\0" \ - "fdt_addr=40080000\0" \ - "kernel_addr=400A0000\0" \ + "fdt_addr=400C0000\0" \ + "kernel_addr=40100000\0" \ "ramdisk_addr=40280000\0" \ + "load=tftp 200000 ${u-boot}\0" \ + "update=protect off 40000000 +${filesize};" \ + "erase 40000000 +${filesize};" \ + "cp.b 200000 40000000 ${filesize};" \ + "protect on 40000000 +${filesize}\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" @@ -215,7 +220,7 @@ #define CFG_FLASH_BASE 0x40000000 #define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #define CFG_MONITOR_BASE CFG_FLASH_BASE -#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */ /* * For booting Linux, the board info and command line data @@ -236,7 +241,7 @@ #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */ #define CFG_ENV_SIZE 0x08000 /* Total Size of Environment Sector */ -#define CFG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */ +#define CFG_ENV_SECT_SIZE 0x40000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ #define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE) -- cgit From d43e489baf02afae49077791fb22332d240d8656 Mon Sep 17 00:00:00 2001 From: Martin Krause Date: Thu, 27 Sep 2007 14:54:36 +0200 Subject: TQM866M: fix SDRAM refresh At 133 MHz the current SDRAM refresh rate is too fast (measured 4 * 1.17 us). CFG_MAMR_PTA changes from 39 to 97. This result in a refresh rate of 4 * 7.8 us at the default clock 50 MHz. At 133 MHz the value will be then 4 * 2.9 us. This is a compromise until a new method is found to adjust the refresh rate. Signed-off-by: Martin Krause --- include/configs/TQM866M.h | 36 ++++++++++++++++++++---------------- 1 file changed, 20 insertions(+), 16 deletions(-) (limited to 'include') diff --git a/include/configs/TQM866M.h b/include/configs/TQM866M.h index 76facc4295..ca3c166524 100644 --- a/include/configs/TQM866M.h +++ b/include/configs/TQM866M.h @@ -426,26 +426,30 @@ #define CFG_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64)) /* - * Memory Periodic Timer Prescaler - * Periodic timer for refresh, start with refresh rate for 40 MHz clock - * (CFG_8xx_CPUCLK_MIN / CFG_PTA_PER_CLK) + * Periodic timer (MAMR[PTx]) for 4 * 7.8 us refresh (= 31.2 us per quad) + * + * CPUclock(MHz) * 31.2 + * CFG_MAMR_PTA = ----------------------------------- with DFBRG = 0 + * 2^(2*SCCR[DFBRG]) * MPTPR_PTP_DIV16 + * + * CPU clock = 15 MHz: CFG_MAMR_PTA = 29 -> 4 * 7.73 us + * CPU clock = 50 MHz: CFG_MAMR_PTA = 97 -> 4 * 7.76 us + * CPU clock = 66 MHz: CFG_MAMR_PTA = 128 -> 4 * 7.75 us + * CPU clock = 133 MHz: CFG_MAMR_PTA = 255 -> 4 * 7.67 us + * + * Value 97 is for 4 * 7.8 us at 50 MHz. So the refresh cycle requirement will + * be met also in the default configuration, i.e. if environment variable + * 'cpuclk' is not set. */ -#define CFG_MAMR_PTA 39 +#define CFG_MAMR_PTA 97 /* - * For 16 MBit, refresh rates could be 31.3 us - * (= 64 ms / 2K = 125 / quad bursts). - * For a simpler initialization, 15.6 us is used instead. - * - * #define CFG_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks - * #define CFG_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank + * Memory Periodic Timer Prescaler Register (MPTPR) values. */ -#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ -#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ - -/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ -#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ -#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ +/* 4 * 7.8 us refresh (= 31.2 us per quad) at 50 MHz and PTA = 97 */ +#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 +/* 4 * 3.9 us refresh (= 15.6 us per quad) at 50 MHz and PTA = 97 */ +#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* * MAMR settings for SDRAM -- cgit From da3aad55cbde80ab6e301aafa82a2c411aa53eff Mon Sep 17 00:00:00 2001 From: Martin Krause Date: Wed, 26 Sep 2007 17:55:56 +0200 Subject: TQM860M: adjust for doubled flash sector size. Adjust flash map to support the new S29GLxxN (N-Type) Flashes with doubled sector size. Signed-off-by: Martin Krause --- include/configs/TQM860M.h | 13 +++++++++---- 1 file changed, 9 insertions(+), 4 deletions(-) (limited to 'include') diff --git a/include/configs/TQM860M.h b/include/configs/TQM860M.h index 684b86f2ef..fe3a2f020c 100644 --- a/include/configs/TQM860M.h +++ b/include/configs/TQM860M.h @@ -69,9 +69,14 @@ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "rootpath=/opt/eldk/ppc_8xx\0" \ "bootfile=/tftpboot/TQM860M/uImage\0" \ - "fdt_addr=40080000\0" \ - "kernel_addr=400A0000\0" \ + "fdt_addr=400C0000\0" \ + "kernel_addr=40100000\0" \ "ramdisk_addr=40280000\0" \ + "load=tftp 200000 ${u-boot}\0" \ + "update=protect off 40000000 +${filesize};" \ + "erase 40000000 +${filesize};" \ + "cp.b 200000 40000000 ${filesize};" \ + "protect on 40000000 +${filesize}\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" @@ -172,7 +177,7 @@ #define CFG_FLASH_BASE 0x40000000 #define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #define CFG_MONITOR_BASE CFG_FLASH_BASE -#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */ /* * For booting Linux, the board info and command line data @@ -193,7 +198,7 @@ #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */ #define CFG_ENV_SIZE 0x08000 /* Total Size of Environment Sector */ -#define CFG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */ +#define CFG_ENV_SECT_SIZE 0x40000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ #define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE) -- cgit From 7ee6ba1a056e4061ab4cfde30127e332e7957afd Mon Sep 17 00:00:00 2001 From: "runet@innovsys.com" Date: Tue, 16 Oct 2007 14:50:40 -0500 Subject: Make MPC8266ADS board compile again. Signed-off-by: Runet Torgersen --- include/configs/MPC8266ADS.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include') diff --git a/include/configs/MPC8266ADS.h b/include/configs/MPC8266ADS.h index 14b041e3ae..d392b981ed 100644 --- a/include/configs/MPC8266ADS.h +++ b/include/configs/MPC8266ADS.h @@ -168,6 +168,7 @@ #undef CONFIG_CMD_MFSL #undef CONFIG_CMD_MMC #undef CONFIG_CMD_NAND +#undef CONFIG_CMD_ONENAND #undef CONFIG_CMD_PCMCIA #undef CONFIG_CMD_REISER #undef CONFIG_CMD_SCSI @@ -177,6 +178,7 @@ #undef CONFIG_CMD_UNIVERSE #undef CONFIG_CMD_USB #undef CONFIG_CMD_XIMG +#undef CONFIG_CMD_AT91_SPIMUX /* Define a command string that is automatically executed when no character * is read on the console interface withing "Boot Delay" after reset. -- cgit From a3063eec775719b7e91023bbec3f64b3118791df Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Thu, 11 Oct 2007 00:18:48 -0500 Subject: Set OF_STDOUT_PATH to match the default console on MPC8568 MDS On the MPC8568 MDS we use ttyS0, UART0, etc. as the standard configured console. Make it so we match that config what we tell Linux as the early STDOUT console. Signed-off-by: Kumar Gala --- include/configs/MPC8568MDS.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index ba744e99f8..548e1582a8 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -297,7 +297,7 @@ extern unsigned long get_clock_freq(void); #define OF_SOC "soc8568@e0000000" #define OF_QE "qe@e0080000" #define OF_TBCLK (bd->bi_busfreq / 8) -#define OF_STDOUT_PATH "/soc8568@e0000000/serial@4600" +#define OF_STDOUT_PATH "/soc8568@e0000000/serial@4500" /* * I2C -- cgit From 7600d47b8f6a10019e537dc9a62aa1498df58d25 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Thu, 11 Oct 2007 00:29:18 -0500 Subject: Improve handling of PCI interrupt device tree fixup on MPC85xx CDS On the MPC85xx CDS we have two issues: 1. The device tree fixup code did not check to see if the property we are trying to update is actually found. Its possible that it would update random memory starting at 0. 2. Newer Linux kernel's have moved the location of the PCI nodes to be sibilings of the soc node and not children. The explicit PATH to the PCI node would not be found for these device trees. Add the ability to handle both paths. In the future we shouldn't handle such fixups by explicit path. Signed-off-by: Kumar Gala --- include/configs/MPC8541CDS.h | 1 + include/configs/MPC8548CDS.h | 1 + include/configs/MPC8555CDS.h | 1 + 3 files changed, 3 insertions(+) (limited to 'include') diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h index 4e061bd9ff..8dda6651ef 100644 --- a/include/configs/MPC8541CDS.h +++ b/include/configs/MPC8541CDS.h @@ -316,6 +316,7 @@ extern unsigned long get_clock_freq(void); #define OF_SOC "soc8541@e0000000" #define OF_TBCLK (bd->bi_busfreq / 8) #define OF_STDOUT_PATH "/soc8541@e0000000/serial@4600" +#define OF_PCI "pci@e0008000" /* * I2C diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h index 6083715189..4edc7fd2b6 100644 --- a/include/configs/MPC8548CDS.h +++ b/include/configs/MPC8548CDS.h @@ -340,6 +340,7 @@ extern unsigned long get_clock_freq(void); #define OF_SOC "soc8548@e0000000" #define OF_TBCLK (bd->bi_busfreq / 8) #define OF_STDOUT_PATH "/soc8548@e0000000/serial@4600" +#define OF_PCI "pci@e0008000" /* * I2C diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h index 1d1b7c9079..c414bf033e 100644 --- a/include/configs/MPC8555CDS.h +++ b/include/configs/MPC8555CDS.h @@ -316,6 +316,7 @@ extern unsigned long get_clock_freq(void); #define OF_SOC "soc8555@e0000000" #define OF_TBCLK (bd->bi_busfreq / 8) #define OF_STDOUT_PATH "/soc8555@e0000000/serial@4600" +#define OF_PCI "pci@e0008000" /* * I2C -- cgit From de9a738faa7c2f47286119c3bfebc3dfbfe7d86d Mon Sep 17 00:00:00 2001 From: Vlad Lungu Date: Sun, 21 Oct 2007 22:10:10 +0900 Subject: [MIPS] Fix UNCACHED_SDRAM PHYSADDR is for physical address, KSEG1ADDR is for uncached. Signed-off-by: Vlad Lungu Signed-off-by: Shinya Kuribayashi --- include/asm-mips/addrspace.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/asm-mips/addrspace.h b/include/asm-mips/addrspace.h index b8214b1c85..0e6abd7d0f 100644 --- a/include/asm-mips/addrspace.h +++ b/include/asm-mips/addrspace.h @@ -49,7 +49,7 @@ cannot access physical memory directly from core */ #define UNCACHED_SDRAM(a) (((unsigned long)(a)) | 0x20000000) #else /* !CONFIG_AU1X00 */ -#define UNCACHED_SDRAM(a) PHYSADDR(a) +#define UNCACHED_SDRAM(a) KSEG1ADDR(a) #endif /* CONFIG_AU1X00 */ #endif /* __ASSEMBLY__ */ /* -- cgit From d3afa1ee19345a31fd1eaad3e98b97d13ca47315 Mon Sep 17 00:00:00 2001 From: Bartlomiej Sieka Date: Tue, 23 Oct 2007 13:14:10 +0200 Subject: Motion-PRO: Update configuration to accomodate next generation board. New board has faster oscillator and a different Flash chip. This affects: - CFG_MPC5XXX_CLKIN - SDRAM timings - Flash CS configuration (timings) - Flash sector size, and thus MTD partition layout - malloc() arena size (due to bigger Flash sectors) - smaller memory test range (due to bigger malloc() arena) This patch also enables more extensive memory testing via "mtest". Signed-off-by: Bartlomiej Sieka --- include/configs/motionpro.h | 29 +++++++++++++++-------------- 1 file changed, 15 insertions(+), 14 deletions(-) (limited to 'include') diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h index 9a21632162..1503598166 100644 --- a/include/configs/motionpro.h +++ b/include/configs/motionpro.h @@ -163,9 +163,9 @@ /* - * Clock configuration: SYS_XTALIN = 25MHz + * Clock configuration: SYS_XTALIN = 33MHz */ -#define CFG_MPC5XXX_CLKIN 25000000 +#define CFG_MPC5XXX_CLKIN 33000000 /* @@ -211,7 +211,7 @@ #endif #define CFG_MONITOR_LEN (256 << 10) /* 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 << 10) /* 128 kB for malloc() */ +#define CFG_MALLOC_LEN (1024 << 10) /* 1 MiB for malloc() */ #define CFG_BOOTMAPSZ (8 << 20) /* initial mem map for Linux */ @@ -221,7 +221,7 @@ /* Boot Chipselect */ #define CFG_BOOTCS_START CFG_FLASH_BASE #define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#define CFG_BOOTCS_CFG 0x03035D00 +#define CFG_BOOTCS_CFG 0x00045D00 /* Flash memory addressing */ #define CFG_CS0_START CFG_FLASH_BASE @@ -251,11 +251,11 @@ /* * SDRAM configuration */ -/* 2 x MT48LC16M16A2BG-75 IT:D, CASL 2, 32 bit data bus */ -#define SDRAM_CONFIG1 0x52222600 -#define SDRAM_CONFIG2 0x88b70000 -#define SDRAM_CONTROL 0x50570000 -#define SDRAM_MODE 0x008d0000 +/* 2 x MT48LC16M16A2BG-75 IT:D, CASL 3, 32 bit data bus */ +#define SDRAM_CONFIG1 0x62322900 +#define SDRAM_CONFIG2 0x88c70000 +#define SDRAM_CONTROL 0x504f0000 +#define SDRAM_MODE 0x00cd0000 /* @@ -267,7 +267,7 @@ #define CFG_FLASH_SIZE 0x01000000 #define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */ #define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } -#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */ +#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */ #define CONFIG_FLASH_16BIT /* Flash is 16-bit */ /* @@ -277,8 +277,8 @@ #define MTDIDS_DEFAULT "nor0=motionpro-0" #define MTDPARTS_DEFAULT "mtdparts=motionpro-0:" \ "13m(fs),2m(kernel),256k(uboot)," \ - "64k(env),64k(redund_env),64k(dtb)," \ - "-(user_data)" + "128k(env),128k(redund_env)," \ + "128k(dtb),-(user_data)" /* * IDE/ATA configuration @@ -356,7 +356,7 @@ extern void __led_set(led_id_t id, int state); /* This has to be a multiple of the Flash sector size */ #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) #define CFG_ENV_SIZE 0x1000 -#define CFG_ENV_SECT_SIZE 0x10000 +#define CFG_ENV_SECT_SIZE 0x20000 /* Configuration of redundant environment */ #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE) @@ -394,7 +394,8 @@ extern void __led_set(led_id_t id, int state); #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_MEMTEST_START 0x00100000 /* memtest works on */ -#define CFG_MEMTEST_END 0x03f00000 /* 1 ... 64 MiB in DRAM */ +#define CFG_MEMTEST_END 0x03e00000 /* 1 ... 62 MiB in DRAM */ +#define CFG_ALT_MEMTEST #define CFG_LOAD_ADDR 0x200000 /* default kernel load addr */ -- cgit From 298cd4cafe81ff8a6c87be8fbc440a20720d3ed6 Mon Sep 17 00:00:00 2001 From: Rune Torgersen Date: Wed, 17 Oct 2007 11:56:31 -0500 Subject: Make MPC8266ADS command selection more robust Fix MPC8266 command line definition so it won't break when new commands are added to u-boot. Signed-off-by Rune Torgersen --- include/configs/MPC8266ADS.h | 53 +++++++++++++++++--------------------------- 1 file changed, 20 insertions(+), 33 deletions(-) (limited to 'include') diff --git a/include/configs/MPC8266ADS.h b/include/configs/MPC8266ADS.h index d392b981ed..3659002d5e 100644 --- a/include/configs/MPC8266ADS.h +++ b/include/configs/MPC8266ADS.h @@ -146,39 +146,26 @@ /* * Command line configuration. */ -#include - -#undef CONFIG_CMD_BEDBUG -#undef CONFIG_CMD_BMP -#undef CONFIG_CMD_BSP -#undef CONFIG_CMD_DATE -#undef CONFIG_CMD_DHCP -#undef CONFIG_CMD_DISPLAY -#undef CONFIG_CMD_DOC -#undef CONFIG_CMD_DTT -#undef CONFIG_CMD_EEPROM -#undef CONFIG_CMD_ELF -#undef CONFIG_CMD_EXT2 -#undef CONFIG_CMD_FDC -#undef CONFIG_CMD_FDOS -#undef CONFIG_CMD_HWFLOW -#undef CONFIG_CMD_IDE -#undef CONFIG_CMD_JFFS2 -#undef CONFIG_CMD_KGDB -#undef CONFIG_CMD_MFSL -#undef CONFIG_CMD_MMC -#undef CONFIG_CMD_NAND -#undef CONFIG_CMD_ONENAND -#undef CONFIG_CMD_PCMCIA -#undef CONFIG_CMD_REISER -#undef CONFIG_CMD_SCSI -#undef CONFIG_CMD_SPI -#undef CONFIG_CMD_SNTP -#undef CONFIG_CMD_VFD -#undef CONFIG_CMD_UNIVERSE -#undef CONFIG_CMD_USB -#undef CONFIG_CMD_XIMG -#undef CONFIG_CMD_AT91_SPIMUX +#include + +/* Commands we want, that are not part of default set */ +#define CONFIG_CMD_ASKENV /* ask for env variable */ +#define CONFIG_CMD_CACHE /* icache, dcache */ +#define CONFIG_CMD_DHCP /* DHCP Support */ +#define CONFIG_CMD_DIAG /* Diagnostics */ +#define CONFIG_CMD_IMMAP /* IMMR dump support */ +#define CONFIG_CMD_IRQ /* irqinfo */ +#define CONFIG_CMD_MII /* MII support */ +#define CONFIG_CMD_PCI /* pciinfo */ +#define CONFIG_CMD_PING /* ping support */ +#define CONFIG_CMD_PORTIO /* Port I/O */ +#define CONFIG_CMD_REGINFO /* Register dump */ +#define CONFIG_CMD_SAVES /* save S record dump */ +#define CONFIG_CMD_SDRAM /* SDRAM DIMM SPD info printout */ + +/* Commands from default set we don't need */ +#undef CONFIG_CMD_FPGA /* FPGA configuration Support */ +#undef CONFIG_CMD_SETGETDCR /* DCR support on 4xx */ /* Define a command string that is automatically executed when no character * is read on the console interface withing "Boot Delay" after reset. -- cgit From 2a4741d9a14ec475f50e9856d2c0a67e8b4271bd Mon Sep 17 00:00:00 2001 From: Marcel Ziswiler Date: Fri, 19 Oct 2007 00:25:33 +0200 Subject: fix pxa255_idp board The pxa255_idp being an old unmaintained board showed several issues: 1. CONFIG_INIT_CRITICAL was still defined. 2. Neither CONFIG_MAC_PARTITION nor CONFIG_DOS_PARTITION was defined. 3. Symbol flash_addr was undeclared. 4. The boards lowlevel_init function was still called memsetup. 5. The TEXT_BASE was still 0xa3000000 rather than 0xa3080000. 6. Using -march=armv5 instead of -march=armv5te resulted in lots of 'target CPU does not support interworking' warnings on recent compilers. 7. The PXA's serial driver redefined FFUART, BTUART and STUART used as indexes rather than the register definitions from the pxa-regs header file. Renamed them to FFUART_INDEX, BTUART_INDEX and STUART_INDEX to avoid any ambiguities. 8. There were several redefinition warnings concerning ICMR, OSMR3, OSCR, OWER, OIER, RCSR and CCCR in the PXA's assembly start file. 9. The board configuration file was rather outdated. 10. The part header file defined the vendor, product and revision arrays as unsigned chars instead of just chars in the block_dev_desc_t structure. Signed-off-by: Marcel Ziswiler --- include/configs/pxa255_idp.h | 13 +++++++------ include/part.h | 6 +++--- 2 files changed, 10 insertions(+), 9 deletions(-) (limited to 'include') diff --git a/include/configs/pxa255_idp.h b/include/configs/pxa255_idp.h index 0e884fc114..4a9cadbc73 100644 --- a/include/configs/pxa255_idp.h +++ b/include/configs/pxa255_idp.h @@ -38,10 +38,11 @@ #include /* - * If we are developing, we might want to start armboot from ram + * If we are developing, we might want to start U-Boot from RAM * so we MUST NOT initialize critical regs like mem-timing ... */ -#define CONFIG_INIT_CRITICAL /* undef for developing */ +#undef CONFIG_SKIP_LOWLEVEL_INIT /* define for developing */ +#undef CONFIG_SKIP_RELOCATE_UBOOT /* define for developing */ /* * define the following to enable debug blinks. A debug blink function @@ -62,6 +63,7 @@ #endif #define CONFIG_MMC 1 +#define CONFIG_DOS_PARTITION 1 #define BOARD_LATE_INIT 1 #undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ @@ -121,7 +123,6 @@ #define CONFIG_CMD_FAT #define CONFIG_CMD_DHCP - #define CONFIG_BOOTDELAY 3 #define CONFIG_BOOTCOMMAND "bootm 40000" #define CONFIG_BOOTARGS "root=/dev/mtdblock2 rootfstype=cramfs console=ttyS0,115200" @@ -332,7 +333,7 @@ #define CFG_FLASH_CFI_DRIVER 1 #define CFG_MONITOR_BASE 0 -#define CFG_MONITOR_LEN 0x40000 +#define CFG_MONITOR_LEN PHYS_FLASH_SECT_SIZE #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ @@ -347,7 +348,7 @@ #define CFG_ENV_IS_IN_FLASH 1 /* Addr of Environment Sector */ #define CFG_ENV_ADDR (PHYS_FLASH_1 + PHYS_FLASH_SIZE - 0x40000) -#define CFG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */ -#define CFG_ENV_SECT_SIZE 0x40000 +#define CFG_ENV_SIZE PHYS_FLASH_SECT_SIZE /* Total Size of Environment Sector */ +#define CFG_ENV_SECT_SIZE (PHYS_FLASH_SECT_SIZE / 16) #endif /* __CONFIG_H */ diff --git a/include/part.h b/include/part.h index 29c03205f2..37b2b6845b 100644 --- a/include/part.h +++ b/include/part.h @@ -38,9 +38,9 @@ typedef struct block_dev_desc { #endif lbaint_t lba; /* number of blocks */ unsigned long blksz; /* block size */ - unsigned char vendor [40+1]; /* IDE model, SCSI Vendor */ - unsigned char product[20+1]; /* IDE Serial no, SCSI product */ - unsigned char revision[8+1]; /* firmware revision */ + char vendor [40+1]; /* IDE model, SCSI Vendor */ + char product[20+1]; /* IDE Serial no, SCSI product */ + char revision[8+1]; /* firmware revision */ unsigned long (*block_read)(int dev, unsigned long start, lbaint_t blkcnt, -- cgit From 10cdb8dbd67a818823ab9ec88b68fc348903db59 Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Fri, 19 Oct 2007 00:24:59 +0200 Subject: lubbock: Fix no partition type specified, use DOS as default Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD --- include/configs/lubbock.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include') diff --git a/include/configs/lubbock.h b/include/configs/lubbock.h index 4adf254221..82fe19c725 100644 --- a/include/configs/lubbock.h +++ b/include/configs/lubbock.h @@ -42,6 +42,7 @@ #endif #define CONFIG_MMC 1 #define BOARD_LATE_INIT 1 +#define CONFIG_DOS_PARTITION #undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ -- cgit From e78220f6e514206757acfe247297fc9a328a881f Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Fri, 19 Oct 2007 06:33:45 +0200 Subject: xsengine: Fix no partition type specified, use DOS as default Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD --- include/configs/xsengine.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include') diff --git a/include/configs/xsengine.h b/include/configs/xsengine.h index 5733933d61..766617e075 100644 --- a/include/configs/xsengine.h +++ b/include/configs/xsengine.h @@ -32,6 +32,7 @@ #define CONFIG_PXA250 1 /* This is an PXA250 CPU */ #define CONFIG_XSENGINE 1 #define CONFIG_MMC 1 +#define CONFIG_DOS_PARTITION 1 #define BOARD_POST_INIT 1 #undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ #define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */ -- cgit From e9d0d527992566ebef9826962ff1745b2f082b92 Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Fri, 19 Oct 2007 10:55:24 +0200 Subject: delta: Fix OHCI_REGS_BASE undeclared and wait_ms implicit declaration Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD --- include/configs/delta.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include') diff --git a/include/configs/delta.h b/include/configs/delta.h index 09667edaa5..14fde1a957 100644 --- a/include/configs/delta.h +++ b/include/configs/delta.h @@ -123,6 +123,8 @@ #define CONFIG_USB_STORAGE 1 #define CONFIG_DOS_PARTITION 1 +#include /* for OHCI_REGS_BASE */ + #undef CFG_USB_OHCI_BOARD_INIT #define CFG_USB_OHCI_CPU_INIT 1 #define CFG_USB_OHCI_REGS_BASE OHCI_REGS_BASE -- cgit From 7b0a42219f30277f71f4405cbaf8a269f6d2d227 Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Sun, 21 Oct 2007 09:14:28 +0200 Subject: Mips: Fix string functions differ prototype declaration Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD --- include/asm-mips/string.h | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) (limited to 'include') diff --git a/include/asm-mips/string.h b/include/asm-mips/string.h index c42ad82c47..579a591e62 100644 --- a/include/asm-mips/string.h +++ b/include/asm-mips/string.h @@ -19,21 +19,21 @@ extern char *strcpy(char *__dest, __const__ char *__src); #undef __HAVE_ARCH_STRNCPY -extern char *strncpy(char *__dest, __const__ char *__src, size_t __n); +extern char *strncpy(char *__dest, __const__ char *__src, __kernel_size_t __n); #undef __HAVE_ARCH_STRCMP extern int strcmp(__const__ char *__cs, __const__ char *__ct); #undef __HAVE_ARCH_STRNCMP -extern int strncmp(__const__ char *__cs, __const__ char *__ct, size_t __count); +extern int strncmp(__const__ char *__cs, __const__ char *__ct, __kernel_size_t __count); #undef __HAVE_ARCH_MEMSET -extern void *memset(void *__s, int __c, size_t __count); +extern void *memset(void *__s, int __c, __kernel_size_t __count); #undef __HAVE_ARCH_MEMCPY -extern void *memcpy(void *__to, __const__ void *__from, size_t __n); +extern void *memcpy(void *__to, __const__ void *__from, __kernel_size_t __n); #undef __HAVE_ARCH_MEMMOVE -extern void *memmove(void *__dest, __const__ void *__src, size_t __n); +extern void *memmove(void *__dest, __const__ void *__src, __kernel_size_t __n); #endif /* _ASM_STRING_H */ -- cgit From b31f64343ead9482cd439b1adbe4c34026a641b1 Mon Sep 17 00:00:00 2001 From: Martin Krause Date: Mon, 22 Oct 2007 16:45:53 +0200 Subject: TQM5200: fix spurious characters on second serial interface With this patch PSC3 is configured as UART. This is done, because if the pins of PSC3 are not configured at all (-> all pins are GPI), due to crosstalk, spurious characters may be send over the RX232_2_TXD signal line. Signed-off-by: Martin Krause --- include/configs/TQM5200.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index d55340404d..c3f16f524e 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -547,7 +547,7 @@ # if defined (CONFIG_TQM5200_REV100) # error TQM5200 REV100 not supported on STK52XX REV200 or above # else/* TQM5200 REV200 and above */ -# define CFG_GPS_PORT_CONFIG 0x91500004 +# define CFG_GPS_PORT_CONFIG 0x91500404 # endif # endif #elif defined (CONFIG_FO300) -- cgit From 1a0ce20aa4cb4e3068da04e7290ee9986fd0b834 Mon Sep 17 00:00:00 2001 From: Martin Krause Date: Wed, 24 Oct 2007 08:42:25 +0200 Subject: TQM5200: fix spurious characters on second serial interface With this patch PSC3 is configured as UART. This is done, because if the pins of PSC3 are not configured at all (-> all pins are GPI), due to crosstalk, spurious characters may be send over the RX232_2_TXD signal line. Signed-off-by: Martin Krause Signed-off-by: Grant Likely --- include/configs/TQM5200.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index d55340404d..c3f16f524e 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -547,7 +547,7 @@ # if defined (CONFIG_TQM5200_REV100) # error TQM5200 REV100 not supported on STK52XX REV200 or above # else/* TQM5200 REV200 and above */ -# define CFG_GPS_PORT_CONFIG 0x91500004 +# define CFG_GPS_PORT_CONFIG 0x91500404 # endif # endif #elif defined (CONFIG_FO300) -- cgit From d78791ae914d4e7c5edca1cdad73b3dc81a4eb82 Mon Sep 17 00:00:00 2001 From: Bartlomiej Sieka Date: Thu, 25 Oct 2007 17:20:01 +0200 Subject: TQM5200: increase kernel_addr_r and fdt_addr_r (hinted by Wolfgang Denk). Signed-off-by: Bartlomiej Sieka --- include/configs/TQM5200.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index c3f16f524e..7ecc275a1c 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -257,8 +257,8 @@ "fdt_addr=FC0A0000\0" \ "kernel_addr=FC0C0000\0" \ "ramdisk_addr=FC300000\0" \ - "kernel_addr_r=200000\0" \ - "fdt_addr_r=400000\0" \ + "kernel_addr_r=400000\0" \ + "fdt_addr_r=600000\0" \ "rootpath=/opt/eldk/ppc_6xx\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ -- cgit From 2acefa72ee0026f862ab65597ca687428f63a973 Mon Sep 17 00:00:00 2001 From: TsiChungLiew Date: Thu, 25 Oct 2007 17:09:17 -0500 Subject: ColdFire 5282: Fix external flash boot and return dramsize Signed-off-by: TsiChungLiew --- include/configs/M5282EVB.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/M5282EVB.h b/include/configs/M5282EVB.h index 3c17c1ea14..7bb9f60f76 100644 --- a/include/configs/M5282EVB.h +++ b/include/configs/M5282EVB.h @@ -163,7 +163,7 @@ * Please note that CFG_SDRAM_BASE _must_ start at 0 */ #define CFG_SDRAM_BASE 0x00000000 -#define CFG_SDRAM_SIZE 8 /* SDRAM size in MB */ +#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ #define CFG_FLASH_BASE 0xffe00000 #define CFG_INT_FLASH_BASE 0xf0000000 #define CFG_INT_FLASH_ENABLE 0x21 -- cgit From 95e9f2c212a65610b2e59a5c00d0113383a4da0b Mon Sep 17 00:00:00 2001 From: TsiChungLiew Date: Thu, 25 Oct 2007 17:10:23 -0500 Subject: ColdFire 5253: Assign correct SDRAM size Signed-off-by: TsiChungLiew --- include/configs/M5253EVBE.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/M5253EVBE.h b/include/configs/M5253EVBE.h index 48170e7a35..f5e1b646ca 100644 --- a/include/configs/M5253EVBE.h +++ b/include/configs/M5253EVBE.h @@ -146,7 +146,7 @@ * Please note that CFG_SDRAM_BASE _must_ start at 0 */ #define CFG_SDRAM_BASE 0x00000000 -#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ +#define CFG_SDRAM_SIZE 8 /* SDRAM size in MB */ #ifdef CONFIG_MONITOR_IS_IN_RAM #define CFG_MONITOR_BASE 0x20000 -- cgit From c67e12e705b204cfe914e3e3e693d69a445dcabf Mon Sep 17 00:00:00 2001 From: TsiChungLiew Date: Thu, 25 Oct 2007 17:12:36 -0500 Subject: ColdFire 5329: Assign correct SDRAM size and fix cache Signed-off-by: TsiChungLiew --- include/configs/M5329EVB.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/M5329EVB.h b/include/configs/M5329EVB.h index d3b160505b..47d74a3c37 100644 --- a/include/configs/M5329EVB.h +++ b/include/configs/M5329EVB.h @@ -175,7 +175,7 @@ * Please note that CFG_SDRAM_BASE _must_ start at 0 */ #define CFG_SDRAM_BASE 0x40000000 -#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ +#define CFG_SDRAM_SIZE 32 /* SDRAM size in MB */ #define CFG_SDRAM_CFG1 0x53722730 #define CFG_SDRAM_CFG2 0x56670000 #define CFG_SDRAM_CTRL 0xE1092000 -- cgit From e8ee8f3ade2a06c1893dd5e68f223070d650c7ed Mon Sep 17 00:00:00 2001 From: TsiChungLiew Date: Thu, 25 Oct 2007 17:16:22 -0500 Subject: ColdFire 54455: Fix correct boot location for atmel and intel Signed-off-by: TsiChungLiew --- include/configs/M54455EVB.h | 36 ++++++++++++++++++++---------------- 1 file changed, 20 insertions(+), 16 deletions(-) (limited to 'include') diff --git a/include/configs/M54455EVB.h b/include/configs/M54455EVB.h index 6f4859c238..ba050cb7e4 100644 --- a/include/configs/M54455EVB.h +++ b/include/configs/M54455EVB.h @@ -27,8 +27,8 @@ * board/config.h - configuration options, board specific */ -#ifndef _JAMICA54455_H -#define _JAMICA54455_H +#ifndef _M54455EVB_H +#define _M54455EVB_H /* * High Level Configuration Options @@ -75,7 +75,7 @@ #define CONFIG_CMD_MISC #define CONFIG_CMD_MII #define CONFIG_CMD_NET -#define CONFIG_CMD_PCI +#undef CONFIG_CMD_PCI #define CONFIG_CMD_PING #define CONFIG_CMD_REGINFO @@ -129,8 +129,8 @@ "u-boot=u-boot.bin\0" \ "load=tftp ${loadaddr) ${u-boot}\0" \ "upd=run load; run prog\0" \ - "prog=prot off 0 2ffff;" \ - "era 0 2ffff;" \ + "prog=prot off 4000000 402ffff;" \ + "era 4000000 402ffff;" \ "cp.b ${loadaddr} 0 ${filesize};" \ "save\0" \ "" @@ -174,6 +174,7 @@ #define CFG_IMMR CFG_MBAR /* PCI */ +#ifdef CONFIG_CMD_PCI #define CONFIG_PCI 1 #define CFG_PCI_MEM_BUS 0xA0000000 @@ -187,6 +188,7 @@ #define CFG_PCI_CFG_BUS 0xB0000000 #define CFG_PCI_CFG_PHYS CFG_PCI_CFG_BUS #define CFG_PCI_CFG_SIZE 0x01000000 +#endif /* FPGA - Spartan 2 */ /* experiment @@ -268,8 +270,6 @@ /* Configuration for environment * Environment is embedded in u-boot in the second sector of the flash */ -#define CFG_ENV_OFFSET 0x4000 -#define CFG_ENV_SECT_SIZE 0x2000 #define CFG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_OVERWRITE 1 #undef CFG_ENV_IS_EMBEDDED @@ -278,13 +278,17 @@ * FLASH organization */ #ifdef CFG_ATMEL_BOOT -# define CFG_FLASH_BASE 0 +# define CFG_FLASH_BASE CFG_CS0_BASE # define CFG_FLASH0_BASE CFG_CS0_BASE # define CFG_FLASH1_BASE CFG_CS1_BASE +# define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x4000) +# define CFG_ENV_SECT_SIZE 0x2000 #else # define CFG_FLASH_BASE CFG_FLASH0_BASE # define CFG_FLASH0_BASE CFG_CS1_BASE # define CFG_FLASH1_BASE CFG_CS0_BASE +# define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x60000) +# define CFG_ENV_SECT_SIZE 0x20000 #endif /* M54455EVB has one non CFI flash, defined CFG_FLASH_CFI will cause the system @@ -328,9 +332,9 @@ * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support. */ #ifdef CFG_ATMEL_BOOT -# define CONFIG_JFFS2_DEV "nor0" +# define CONFIG_JFFS2_DEV "nor1" # define CONFIG_JFFS2_PART_SIZE 0x01000000 -# define CONFIG_JFFS2_PART_OFFSET CFG_FLASH1_BASE +# define CONFIG_JFFS2_PART_OFFSET (CFG_FLASH1_BASE + 0x500000) #else # define CONFIG_JFFS2_DEV "nor0" # define CONFIG_JFFS2_PART_SIZE (0x01000000 - 0x500000) @@ -356,20 +360,20 @@ #ifdef CFG_ATMEL_BOOT /* Atmel Flash */ -#define CFG_CS0_BASE 0 +#define CFG_CS0_BASE 0x04000000 #define CFG_CS0_MASK 0x00070001 #define CFG_CS0_CTRL 0x00001140 /* Intel Flash */ -#define CFG_CS1_BASE 0x04000000 +#define CFG_CS1_BASE 0x00000000 #define CFG_CS1_MASK 0x01FF0001 -#define CFG_CS1_CTRL 0x003F3D60 +#define CFG_CS1_CTRL 0x00000D60 #define CFG_ATMEL_BASE CFG_CS0_BASE #else /* Intel Flash */ -#define CFG_CS0_BASE 0 +#define CFG_CS0_BASE 0x00000000 #define CFG_CS0_MASK 0x01FF0001 -#define CFG_CS0_CTRL 0x003F3D60 +#define CFG_CS0_CTRL 0x00000D60 /* Atmel Flash */ #define CFG_CS1_BASE 0x04000000 #define CFG_CS1_MASK 0x00070001 @@ -388,4 +392,4 @@ #define CFG_CS3_MASK 0x00070001 #define CFG_CS3_CTRL 0x00000020 -#endif /* _JAMICA54455_H */ +#endif /* _M54455EVB_H */ -- cgit From 8b6684a698500be9c142ec2c9f46cfc348e17f0c Mon Sep 17 00:00:00 2001 From: Haavard Skinnemoen Date: Wed, 24 Oct 2007 15:48:37 +0200 Subject: ATSTK1002: Remove default ethernet addresses Wolfgang is right: It's not a good idea to set up default initial ethernet addresses for a board, even though they belong to the local range. This will change the failure mode from "IT manager screams at you for using duplicate ethernet addresses" to a nice error message explaining that the ethernet address hasn't been set properly. Signed-off-by: Haavard Skinnemoen --- include/configs/atstk1002.h | 11 +++-------- 1 file changed, 3 insertions(+), 8 deletions(-) (limited to 'include') diff --git a/include/configs/atstk1002.h b/include/configs/atstk1002.h index 1809fc5d86..b33e26fe01 100644 --- a/include/configs/atstk1002.h +++ b/include/configs/atstk1002.h @@ -114,15 +114,10 @@ #define CONFIG_AUTOBOOT_STOP_STR " " /* - * These are "locally administered ethernet addresses" generated by - * ./tools/gen_eth_addr - * - * After booting the board for the first time, new addresses should be - * generated and assigned to the environment variables "ethaddr" and - * "eth1addr". + * After booting the board for the first time, new ethernet addresses + * should be generated and assigned to the environment variables + * "ethaddr" and "eth1addr". This is normally done during production. */ -#define CONFIG_ETHADDR 6a:87:71:14:cd:cb -#define CONFIG_ETH1ADDR ca:f8:15:e6:3e:e6 #define CONFIG_OVERWRITE_ETHADDR_ONCE 1 #define CONFIG_NET_MULTI 1 -- cgit