summaryrefslogtreecommitdiffstats
path: root/include
Commit message (Collapse)AuthorAgeFilesLines
...
| * | colibri-imx6ull: migrate mmc to using driver modelMarcel Ziswiler2019-04-251-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Migrate MMC to using driver model. Migrate USDHC to using pinctrl. While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing. While at it also update copyright period. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
| * | apalis/colibri_imx6/imx6ull: make sure loadaddr does not collideStefan Agner2019-04-253-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently $loadaddr and $fdt_addr_r point to the same address. This might be not ideal for some distro boot scripts which make use of $loadaddr after loading the device tree. Make sure the two variables point to two different addresses. Moving $loadaddr is not entirly trivial since it is defined in mx6_common.h. Move $fdt_addr_r and $ramdisk_addr_r by 1MiB, which should be enough for scripts. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
| * | imx: support i.MX8QM MEK boardPeng Fan2019-04-251-0/+176
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add i.MX8QM MEK board support. Included a basic dts, enabled SPL FIT Boot log as below: U-Boot SPL 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800) Normal Boot Trying to boot from MMC2_2 U-Boot 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800) CPU: NXP i.MX8QM RevB A53 at 142933 MHz Model: Freescale i.MX8QM MEK Board: iMX8QM MEK Build: SCFW 9330215b Boot: SD1 DRAM: 6 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000 Net: Error: ethernet@5b040000 address not set. eth-1: ethernet@5b040000 Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com>
| * | dt-bindings: clock: dt-bindings: pinctrl: add i.MX8QM clocks definitionPeng Fan2019-04-251-0/+846
| | | | | | | | | | | | | | | | | | Add i.MX8QM clocks definition Signed-off-by: Peng Fan <peng.fan@nxp.com>
| * | dt-bindings: pinctrl: add i.MX8QM pads definitionPeng Fan2019-04-251-0/+961
| | | | | | | | | | | | | | | | | | Add i.MX8QM pads definition Signed-off-by: Peng Fan <peng.fan@nxp.com>
| * | Convert CONFIG_USB_EHCI_MX5 to KconfigLukasz Majewski2019-04-257-7/+0
| | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_USB_EHCI_MX5 Signed-off-by: Lukasz Majewski <lukma@denx.de>
| * | ARM: config: Remove not needed CONFIG_MXC_USB_PORT defineLukasz Majewski2019-04-251-1/+0
| | | | | | | | | | | | | | | | | | | | | After i.MX5's EHCI conversion to DM, the CONFIG_MXC_USB_PORT is not needed anymore and should be removed. Signed-off-by: Lukasz Majewski <lukma@denx.de>
| * | ARM: kp_imx53: config: Do not use ${boardtype} to setup update wic fileLukasz Majewski2019-04-251-1/+1
| | | | | | | | | | | | | | | | | | | | | After unification of the rootfs for both HSC and DDC devices, only one, common wic file is necessary - without the distinction of specific board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
| * | ARM: Remove non DM/DTS esdhc3 code from HSC|DDC board related filesLukasz Majewski2019-04-251-4/+0
| | | | | | | | | | | | | | | | | | | | | After switching to DM/DTS support of esdhc3 - the code in this patch can be removed. Signed-off-by: Lukasz Majewski <lukma@denx.de>
| * | ARM: defconfig: Move CONFIG_FSL_ESDHC to KconfigLukasz Majewski2019-04-251-1/+0
| | | | | | | | | | | | | | | | | | | | | The CONFIG_FSL_ESDHC is now enabled and defined in Kconfig, not in include/configs/kp_imx53.h Signed-off-by: Lukasz Majewski <lukma@denx.de>
| * | ARM: omap3_logic: Enable UUIDAdam Ford2019-04-251-2/+4
| | | | | | | | | | | | | | | | | | | | | Instead of hardcoding the mmcroot to /dev/mmcblkX, use the UUID method. Signed-off-by: Adam Ford <aford173@gmail.com>
| * | ARM: imx6q_logic: Allow optional arguments to cmd lineAdam Ford2019-04-251-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | This adds an extra, optional environmental variable called 'optargs' which if enabled allow additional parameters to be passed to the kernel (ie, quiet, cma=128M, etc.) Each script that setups the bootargs will just append this. Signed-off-by: Adam Ford <aford173@gmail.com>
| * | imx8: mek: move HUSH_PARSER to defconfigPeng Fan2019-04-251-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move HUSH_PARSER to defconfig, otherwise meet " => run netboot Booting from net ... Unknown command 'if' - try 'help' Unknown command 'then' - try 'help' Unknown command 'else' - try 'help' Unknown command 'fi' - try 'help' Unknown command '0x80280000' - try 'help' Unknown command 'if' - try 'help' Unknown command 'then' - try 'help' Unknown command 'then' - try 'help' Unknown command 'else' - try 'help' Unknown command 'fi' - try 'help' Unknown command 'else' - try 'help' Unknown command 'fi' - try 'help' " Signed-off-by: Peng Fan <peng.fan@nxp.com>
* | | configs: move CONFIG_SPL_TEXT_BASE to KconfigSimon Goldschmidt2019-04-29128-171/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> [trini: Re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com>
* | | avb: add support for named persistent valuesIgor Opaniuk2019-04-263-3/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | AVB 2.0 spec. revision 1.1 introduces support for named persistent values that must be tamper evident and allows AVB to store arbitrary key-value pairs [1]. Introduce implementation of two additional AVB operations read_persistent_value()/write_persistent_value() for retrieving/storing named persistent values. Correspondent pull request in the OP-TEE OS project repo [2]. [1]: https://android.googlesource.com/platform/external/avb/+/android-9.0.0_r22 [2]: https://github.com/OP-TEE/optee_os/pull/2699 Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
* | | firmware: ti_sci: Modify auth_boot TI-SCI API to match new versionAndrew F. Davis2019-04-261-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | SYSFW version 2019.01 introduces a slightly modified version of this API, add support for it here. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
* | | firmware: ti_sci: Add support for firewall managementAndrew F. Davis2019-04-261-0/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TI-SCI message protocol provides support for controlling the firewall configurations available in SoC. Introduce support for the set of TI-SCI message protocol APIs that provide us with this capability of controlling firewalls. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
* | | main: add new bootstage ID for entering cli loopHeiko Schocher2019-04-261-0/+1
| | | | | | | | | | | | | | | | | | | | | adding a new bootstage ID: BOOTSTAGE_ID_ENTER_CLI_LOOP Signed-off-by: Heiko Schocher <hs@denx.de>
* | | Merge git://git.denx.de/u-boot-marvellTom Rini2019-04-265-7/+145
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Add DM based generic watchdog start and reset implementation and remove all ad-hoc implementations (Stefan) - Move mv_sdhci to DM (Pierre) - Misc turris_omnia updates (Pierre) - Change openrd targets to correctly build again (size changes and fixes to the dts targets) and bring it back into Travis builds (Stefan) - Add Kirkwood db-88f6281-bp board (Chris)
| * | | watchdog: Implement generic watchdog_reset() versionStefan Roese2019-04-263-5/+45
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch tries to implement a generic watchdog_reset() function that can be used by all boards that want to service the watchdog device in U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG. Without this approach, new boards or platforms needed to implement a board specific version of this functionality, mostly copy'ing the same code over and over again into their board or platforms code base. With this new generic function, the scattered other functions are now removed to be replaced by the generic one. The new version also enables the configuration of the watchdog timeout via the DT "timeout-sec" property (if enabled via CONFIG_OF_CONTROL). This patch also adds a new flag to the GD flags, to flag that the watchdog is ready to use and adds the pointer to the watchdog device to the GD. This enables us to remove the global "watchdog_dev" variable, which was prone to cause problems because of its potentially very early use in watchdog_reset(), even before the BSS is cleared. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Marek Behún" <marek.behun@nic.cz> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Maxim Sloyko <maxims@google.com> Cc: Erik van Luijk <evanluijk@interact.nl> Cc: Ryder Lee <ryder.lee@mediatek.com> Cc: Weijie Gao <weijie.gao@mediatek.com> Cc: Simon Glass <sjg@chromium.org> Cc: "Álvaro Fernández Rojas" <noltari@gmail.com> Cc: Philippe Reynes <philippe.reynes@softathome.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
| * | | ARM: kirkwood: add db-88f6281-bp boardChris Packham2019-04-261-0/+99
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is Marvell's Kirkwood development board. It has the following features - 512M DDR2 - 2 PCI connectors - 1 x1 PCI-e interface - 1 Gigabit Ethernet Port - 2 SATA Ports - USB 2.0 Interface - SDIO - 128M NAND Flash - 16M SPI Flash It can be strapped to boot from SPI or NAND so there are two defconfigs (one per boot media). Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
| * | | arm: kirkwood: openrd: Increase U-Boot size in flash to make it fitStefan Roese2019-04-261-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We have run now multiple times into size issues with the openrd board port. To finally fix this, this patch now moves the U-Boot size from 0x6.0000 to 0x8.0000, giving enough space for the next time. This also changes the environment location and potentially the MTD partitioning, but I see no better fix for now. Especially since this board does not have an active maintainer. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Chris Packham <judge.packham@gmail.com> Reviewed-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
| * | | arm: kirkwood: openrd: Remove superfluous CONFIG_ENV_ADDRStefan Roese2019-04-261-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove the superfluous CONFIG_ENV_ADDR definition. Its not needed as CONFIG_ENV_OFFSET is also set to the same value. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Chris Packham <judge.packham@gmail.com> Reviewed-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
* | | | Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini2019-04-2612-144/+23
|\ \ \ \ | |/ / / |/| | |
| * | | arm: socfpga: clean up board config filesSimon Goldschmidt2019-04-2511-42/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove outdated defines (not used any more, outdated due to DM conversion) from various socfpga files in include/config. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Marek Vasut <marex@denx.de> Series-version: 3 Series-changes: 2 - added (this) patch with further cleanups to the socfpga board config files
| * | | arm: socfpga: remove CONFIG_SYS_BOOTMAPSZSimon Goldschmidt2019-04-251-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | socfpga_common.h defines CONFIG_SYS_BOOTMAPSZ to 64 MiB. Since having this define overrides the 'bootm_size' env variable for the whole socfpga platform, let's remove this define from socfpga_common.h and instead rely on the 'bootm_size' env variable (which is initialized to 160 MiB in the same file's default env). This gives users the chance to override it in their own environment. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Marek Vasut <marex@denx.de> Series-to: Marek Vasut <marex@denx.de> Series-to: u-boot@lists.denx.de Cover-letter: arm: socfpga: clean up socfpga_common.h This series cleans up the include/configs/socfpga_common.h file a bit. It removes some defines that are used nowhere and cleans up some leftovers after various subsystems have been converted to use DM. END
| * | | arm: socfpga: clean up socfpga_common.hSimon Goldschmidt2019-04-251-40/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove outdated macros and comments (not used any more, outdated due to DM conversion) from socfpga_common.h. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Series-changes: 3 - changed commit message: s/defines/macros and comments/ Series-changes: 2 - remove even more outdated things
| * | | arm: socfpga: move vining_fpga to DM_I2CSimon Goldschmidt2019-04-252-35/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All socfpga boards except for vining_fpga use DM_I2C. Enable DM_I2C for this board and set the EEPROM defines via Kconfig (enabling CONFIG_I2C_EEPROM from MISC). Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Series-changes: 2 - added (this) patch to move socfpga_vining to DM_I2C
| * | | arm: socfpga: put initial U-Boot stack into DDRSimon Goldschmidt2019-04-251-22/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If SPL post-reloc stage puts the stack into DDR, U-Boot should be able to do that, too. The reason to do so is that this way, U-Boot initial stack can be larger than SPL initial stack. In situations where we want to save the SPL in SRAM for next boot without reloading, this prevents overwriting the SPL DTB in SRAM if U-Boot stack usage gets too high. To achieve this, the malloc definition for a10 is moved up and sligthly changed to ensure CONFIG_SYS_INIT_RAM_SIZE is the remaining available size. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
| * | | arm: socfpga: fix comment about SPL memory layoutSimon Goldschmidt2019-04-251-3/+3
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | The comment about SPL memory layout for socfpga gen5 is outdated: the initial malloc memory is now at the end of the SRAM, gd is below it (see board_init_f_alloc_reserve). Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
* | | Merge tag 'pull-24apr19' of git://git.denx.de/u-boot-dmTom Rini2019-04-248-67/+68
|\ \ \ | | | | | | | | | | | | | | | | | | | | Various minor sandbox iumprovements Fixes for tracing with sandbox Refactoring for boot_get_fdt()
| * | | pci: pci.h: add missing maskbitRamon Fried2019-04-231-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | PCI_MSI_FLAGS_MASKBIT was missing from include file, add it. Signed-off-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
| * | | fdtdec: Use fdt_setprop_u32() for fdtdec_set_phandle()Thierry Reding2019-04-231-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The fdt_setprop_u32() function does everything that we need, so we really only use the function as a convenience wrapper, in which case it can simply be a static inline function. Signed-off-by: Thierry Reding <treding@nvidia.com>
| * | | dm: core: Change platform specific translation-offset handlingStefan Roese2019-04-232-21/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Testing has shown that the current DM implementation of a platform / board specific translation offset, as its needed for the SPL on MVEBU platforms is buggy. The translation offset is confingured too late, after the driver bind functions are run. This may result in incorrect address translations. With the current implementation its not possible to configure the offset earlier, as the DM code has not run at all. This patch now removed the set_/get_translation_offset() calls and moves the translation offset into the GD variable translation_offset. This variable will get used when CONFIG_TRANSLATION_OFFSET is enabled. This option is enabled only for MVEBU on ARM32 platforms, where its currenty needed and configured in the SPL. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Pierre Bourdon <delroth@gmail.com> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Simon Glass <sjg@chromium.org> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@konsulko.com> Tested-by: Pierre Bourdon <delroth@gmail.com> Tested-by: Baruch Siach <baruch@tkos.co.il>
| * | | sandbox: Enable the 'trace' command when tracing is usedSimon Glass2019-04-231-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable this by default so that tracing can be inspected if enabled. This cannot rely on the 'imply' in lib/Kconfig since this method of enabling tracing relates on an environment variable (FTRACE) and does not use Kconfig. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | | div64: Use kernel typesSimon Glass2019-04-231-35/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | These functions still use uint32_t and uint64_t but checkpatch now requests that the kernel types be used instead. Update them as well as a few resulting checkpatch errors. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | | initcall: Drop use of header filesSimon Glass2019-04-231-6/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This file should not include header files. They have already been included by the time initcall.h is included. Also, document how to enable debugging in this file. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | | sandbox: Increase the early-trace-buffer sizeSimon Glass2019-04-231-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | This buffer is too small now that sandbox has grown in size. Increase it. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | | sandbox: Improve debugging in initcall_run_list()Simon Glass2019-04-232-2/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At present if one of the initcalls fails on sandbox the address printing is not help, e.g.: initcall sequence 0000557678967c80 failed at call 00005576709dfe1f (err=-96) This is because U-Boot gets relocated high into memory and the relocation offset (gd->reloc_off) does not work correctly for sandbox. Add support for finding the base address of the text region (at least on Linux) and use that to set the relocation offset. This makes the output better: initcall sequence 0000560775957c80 failed at call 0000000000048134 (err=-96) Then you use can use grep to see which init call failed, e.g.: $ grep 0000000000048134 u-boot.map stdio_add_devices Of course another option is to run it with a debugger such as gdb: $ gdb u-boot ... (gdb) br initcall.h:41 Breakpoint 1 at 0x4db9d: initcall.h:41. (2 locations) Note that two locations are reported, since this function is used in both board_init_f() and board_init_r(). (gdb) r Starting program: /tmp/b/sandbox/u-boot [Thread debugging using libthread_db enabled] Using host libthread_db library "/lib/x86_64-linux-gnu/libthread_db.so.1". U-Boot 2018.09-00264-ge0c2ba9814-dirty (Sep 22 2018 - 12:21:46 -0600) DRAM: 128 MiB MMC: Breakpoint 1, initcall_run_list (init_sequence=0x5555559619e0 <init_sequence_f>) at /scratch/sglass/cosarm/src/third_party/u-boot/files/include/initcall.h:41 41 printf("initcall sequence %p failed at call %p (err=%d)\n", (gdb) print *init_fnc_ptr $1 = (const init_fnc_t) 0x55555559c114 <stdio_add_devices> (gdb) Signed-off-by: Simon Glass <sjg@chromium.org>
* | | | Merge tag 'efi-2019-07-rc1-3' of git://git.denx.de/u-boot-efiTom Rini2019-04-243-15/+15
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull request for UEFI sub-system for v2019.07-rc1 (3) This patch series reworks the implementation of the `bootefi` command to remove code duplication by using the LoadImage() boot service to load binaries. Missing short texts for UEFI protocols are added for display by the `efidebug dh` command. Missing parameter checks for AllocatePages() and CreateDeviceNode() are implemented. The constants for protocol GUIDs are changed to match the names in the UEFI specification.
| * | | | efi_loader: check memory type in AllocatePages()Heinrich Schuchardt2019-04-231-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The UEFI specification prescribes that AllocatePages() checks the memory type. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
| * | | | efi_loader: rework bootmgr/bootefi using load_image APIAKASHI Takahiro2019-04-231-4/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the current implementation, bootefi command and EFI boot manager don't use load_image API, instead, use more primitive and internal functions. This will introduce duplicated code and potentially unknown bugs as well as inconsistent behaviours. With this patch, do_efibootmgr() and do_boot_efi() are completely overhauled and re-implemented using load_image API. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Use efi_root as parent handle for the loaded image. LoadImage() should be called with BootPolicy = true by the boot manager. Avoid duplicate free_pool(). Eliminate variable memdp which is not needed after anymore due to "efi_loader: correctly split device path of loaded image". Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
| * | | | efi_loader: consistent naming of protocol GUIDsHeinrich Schuchardt2019-04-231-11/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We should consistently use the same name for protocol GUIDs as defined in the UEFI specification. Not adhering to this rule has led to duplicate definitions for the EFI_LOADED_IMAGE_PROTOCOL_GUID. Adjust misnamed protocol GUIDs. Adjust the text for the graphics output protocol in the output of the `efidebug dh` command. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
| * | | | efi_loader: export root node handleAKASHI Takahiro2019-04-231-0/+3
| |/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a preparatory patch. The root node handle will be used as a dummy parent handle when invoking an EFI image from bootefi/bootmgr command. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Rebased. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
* | | | Merge tag 'u-boot-stm32-mcu-20190423' of https://github.com/pchotard/u-bootTom Rini2019-04-244-2964/+18
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | STM32 MCUs update: - DT rework and alignment with DT kernel v4.20 - mmc: arm_pl180_mmci: Synchronize compatible with kernel v4.20 - mmc: stm32_sdmmc2: Synchronize properties with kernel v4.20 - configs: update for F746/769 boards
| * | | | configs: stm32f746-disco: update EXTRA_ENV_SETTINGSPatrice Chotard2019-04-231-8/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Allows to boot linux distribution. As stm32f746-disco and stm32f769-disco are sharing the same defconfig file, in case of stm32f769-disco build, "fdtfile=..." must be updated with the correct stm32f769 DTB file name. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
| * | | | ARM: dts: stm32: Sync DT with v4.20 kernel for stm32h7Patrice Chotard2019-04-231-1612/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Synchronize stm32h7 device tree with kernel v4.20. U-boot DT files and pinctrl bindings are updated, useless nodes are removed and gpio compatible added. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
| * | | | ARM: dts: stm32: Sync DT with v4.20 kernel for stm32f7Patrice Chotard2019-04-231-1341/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Synchronize stm32f7 device tree with kernel v4.20. All pinctrl bindings are updated. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
| * | | | ARM: dts: stm32: Sync DT files with v4.20 kernel for stm32f4Patrice Chotard2019-04-231-3/+4
| | |_|/ | |/| | | | | | | | | | | | | | | | | | Synchronize stm32f7 device tree with kernel v4.20. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
* | | | Merge tag 'u-boot-amlogic-20190423' of git://git.denx.de/u-boot-amlogicTom Rini2019-04-248-1/+468
|\ \ \ \ | |_|_|/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Add support for Amlogic p200 & p201 Reference Designs - Add Amlogic SoC information display - Add support for the Libretech-AC AML-S805X-AC board - Add Amlogic AXG reset compatible - Add I2C support for Amlogic AXG - Fix AXG PIN and BANK pinctrl definitions - Fix regmap_read_poll_timeout warning about sandbox_timer_add_offset - Add initial support for Amlogic G12A SoC and U200 board - Enable PHY_REALTEK for selected boards - Fix Khadas VIM2 README
generated by cgit (git 2.34.1) at 2026-04-27 22:54:49 +0000