summaryrefslogtreecommitdiffstats
path: root/include/configs/xtfpga.h
Commit message (Collapse)AuthorAgeFilesLines
* treewide: mem: Move mtest related defines to KconfigAshok Reddy Soma2020-05-081-2/+0
| | | | | | | | | | | Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini <trini@konsulko.com>
* env: Finish migration of common ENV optionsTom Rini2019-11-201-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
* Convert CONFIG_MX_CYCLIC to KconfigAdam Ford2019-08-231-2/+0
| | | | | | | | This converts the following to Kconfig: CONFIG_MX_CYCLIC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: David Lechner <david@lechnology.com>
* Convert CONFIG_SHOW_BOOT_PROGRESS to KconfigSimon Glass2019-08-021-1/+0
| | | | | | | This converts the following to Kconfig: CONFIG_SHOW_BOOT_PROGRESS Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_FLASH_CFI_DRIVER et al to KconfigAdam Ford2018-10-191-3/+0
| | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_MISC_INIT_R to KconfigAdam Ford2018-08-171-1/+0
| | | | | | | | | This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
* SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini2018-05-071-2/+1
| | | | | | | | | | | | | | | | | | | | When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert all of CONFIG_CONS_INDEX to KconfigTom Rini2018-03-161-1/+0
| | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_BOOTP_BOOTPATH et al to KconfigAdam Ford2018-02-231-3/+0
| | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
* xtensa: clean up CONFIG_SYS_TEXT_ADDRMax Filippov2018-02-231-3/+2
| | | | | | | Drop CONFIG_SYS_MEMORY_TOP. Rename CONFIG_SYS_TEXT_ADDR to XTENSA_SYS_TEXT_ADDR. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
* xtfpga: enable hush parserMax Filippov2018-02-131-2/+0
| | | | | | | Remove CONFIG_BOOT_RETRY_TIME as it doesn't do much good and enable CONFIG_HUSH_PARSER in xtfpga_defconfig. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
* Move CONFIG_PANIC_HANG to KconfigMasahiro Yamada2017-12-261-4/+0
| | | | | | | | Freescale (NXP) boards have lots of defconfig files per board. I used "imply PANIC_HANG" for them. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: York Sun <york.sun@nxp.com>
* include/configs: drop default definitions of CONFIG_SYS_MAXARGSThomas Petazzoni2017-09-031-2/+0
| | | | | | | | | Now that include/config_fallbacks.h define a sane fallback for CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all configurations that were using the default value. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* include/configs: drop default definitions of CONFIG_SYS_PBSIZEThomas Petazzoni2017-09-031-3/+0
| | | | | | | | | Now that the fallback value of CONFIG_SYS_PBSIZE in include/config_fallbacks.h has been adjusted, remove its definition from a large number of board configuration files. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_CMD_SAVES to KconfigSimon Glass2017-08-111-6/+0
| | | | | | | | | This converts the following to Kconfig: CONFIG_CMD_SAVES Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
* Convert CONFIG_ENV_IS_IN_FLASH to KconfigSimon Glass2017-07-251-1/+0
| | | | | | | This converts the following to Kconfig: CONFIG_ENV_IS_IN_FLASH Signed-off-by: Simon Glass <sjg@chromium.org>
* Kconfig: Finish migration of hashing commandsDaniel Thompson2017-05-311-1/+0
| | | | | | | | | | | | Currently these (board agnostic) commands cannot be selected using menuconfig and friends. Fix this the obvious way. As part of this, don't muddle the meaning of CONFIG_HASH_VERIFY to mean both 'hash -v' and "we have a hashing command" as this makes the Kconfig logic odd. Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> [trini: Re-apply, add imply for a few cases, run moveconfig.py, also migrate CRC32_VERIFY] Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_CMD_DIAG to KconfigSimon Glass2017-04-301-1/+0
| | | | | | | | | This converts the following to Kconfig: CONFIG_CMD_DIAG Signed-off-by: Simon Glass <sjg@chromium.org> [trini: imply CMD_DIAG on some keymile configs] Signed-off-by: Tom Rini <trini@konsulko.com>
* Remove various unused interrupt related codeTom Rini2017-04-061-2/+0
| | | | | | | | | | | | | With d53ecad92f06 some unused interrupt related code was removed. However all of these options are currently unused. Rather than migrate some of these options to Kconfig we just remove the code in question. The only related code changes here are that in some cases we use CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename and move the value local to the code in question. Fixes: d53ecad92f06 ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi") Signed-off-by: Tom Rini <trini@konsulko.com>
* Kconfig: Migrate CONFIG_BAUDRATEPhilipp Tomsich2017-03-191-1/+0
| | | | | | | | Move this in to Kconfig with a default of 115200. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> [trini: Run moveconfig.py, reword commit slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
* common: Add DISPLAY_BOARDINFOLokesh Vutla2016-10-121-1/+0
| | | | | | | | Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default in certain architectures. Migrate all config files. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* common/Kconfig: Add DISPLAY_CPUINFOLokesh Vutla2016-10-121-1/+0
| | | | | | | | Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default in certain architectures. Migrate all config files. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* common, kconfig: move VERSION_VARIABLE to KconfigHeiko Schocher2016-09-091-1/+0
| | | | | | | move VERSION_VARIABLE from board config file into a Kconfig option. Signed-off-by: Heiko Schocher <hs@denx.de>
* xtensa: add support for the 'xtfpga' evaluation boardChris Zankel2016-08-151-0/+268
The 'xtfpga' board is actually a set of FPGA evaluation boards that can be configured to run an Xtensa processor. - Avnet Xilinx LX60 - Avnet Xilinx LX110 - Avnet Xilinx LX200 - Xilinx ML605 - Xilinx KC705 These boards share the same components (open-ethernet, ns16550 serial, lcd display, flash, etc.). Signed-off-by: Chris Zankel <chris@zankel.net> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
generated by cgit (git 2.34.1) at 2024-11-20 03:45:30 +0000