summaryrefslogtreecommitdiffstats
path: root/include/configs/uniphier.h
Commit message (Collapse)AuthorAgeFilesLines
* ARM: uniphier: add sdscript, sdboot, sdupdate environment variablesMasahiro Yamada2020-02-281-0/+11
| | | | | | | | | | | | Add handy macros: - sdscript: source boot.scr in the file system of the SD media - sdboot : boot the kernel using the images in the file system of the SD media - sdscript: update the boot firmware in the SD media (in raw block sectors) Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: use $loadaddr for source commandMasahiro Yamada2020-02-011-3/+3
| | | | | | | | | | | If the "source" command is not given the address, it uses CONFIG_SYS_LOAD_ADDR, which is compile-time determined. Using the "loadaddr" environment variable is handier because it is relocated according to the memory base when CONFIG_POSITION_INDEPENDENT is enabled. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* env: Finish migration of common ENV optionsTom Rini2019-11-201-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
* ARM: uniphier: set {kernel, ramdisk, fdt}_addr_r at boot-timeMasahiro Yamada2019-07-101-7/+7
| | | | | | | | The base of DRAM will be changed for the next generation SoC. The addresses needed for booting the kernel should be shifted according to the DRAM base. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: set loadaddr at boot-timeMasahiro Yamada2019-07-101-2/+2
| | | | | | | | | | | The base of DRAM will be changed for the next generation SoC. To support it along with existing SoCs in the single defconfig, set 'loadaddr' at boot-time by adding the offset to the DRAM base. CONFIG_SYS_LOAD_ADDR is still hard-coded for compilation, but the value from environment variable 'loadaddr' should be used. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: remove CONFIG_SYS_SDRAM_BASEMasahiro Yamada2019-07-101-6/+0
| | | | | | | | | The base address of DRAM was 0x80000000 for all the ARM SoCs of this family in the past. It will be changed to 0x20000000 for a planned new SoC. To support multiple SoCs by the single uniphier_v8_defconfig, the base must be run-time determined. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: remove empty #ifdef blockMasahiro Yamada2019-07-101-4/+0
| | | | | | | This is a remnant of commit f89d6133eef2 ("configs: move CONFIG_SPL_TEXT_BASE to Kconfig"). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* CONFIG_SYS_[DI]CACHE_OFF: remove commented linesTrevor Woerner2019-05-181-4/+0
| | | | | | | | Eventually these configuration items will be converted to Kconfig, therefore there's little point in leaving commented-out versions of them in include/configs. Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
* Convert CONFIG_SUPPORT_EMMC_BOOT to KconfigAlex Kiernan2019-05-041-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek <michal.simek@xilinx.com>, these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
* configs: move CONFIG_SPL_TEXT_BASE to KconfigSimon Goldschmidt2019-04-291-3/+0
| | | | | | | | | Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> [trini: Re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com>
* preboot: Introduce CONFIG_USE_PREBOOT and migrate CONFIG_PREBOOTMasahiro Yamada2019-02-221-2/+0
| | | | | | | | | | | | This is the same migration path as commit b6251db8c3f0 ("Kconfig: Introduce USE_BOOTCOMMAND and migrate BOOTCOMMAND"). I also moved the description in README to the Kconfig help. I ripped off the sentence about 'LWMON' since it is gone already. I only let my boards migrate, leaving the rest to platform maintainers. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: add CONFIG_PREBOOTMasahiro Yamada2018-12-291-0/+2
| | | | | | For more boot-flow flexibility, Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: allow to source boot script before distro-bootMasahiro Yamada2018-12-291-0/+20
| | | | | | | | Some users might need additional setups before booting the kernel. If there is found a file 'boot.scr', run it before invoking the distro boot command. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: do not modify bootcmd environment variable at run-timeMasahiro Yamada2018-12-291-0/+4
| | | | | | | | | | | | | Some users might want to modify 'bootcmd' at compile-time by editing include/configs/uniphier.h, but overwriting it at run-time makes it impossible. Instead, set 'bootdev' at run-time, which contains the boot device the system is booting from, then indirectly reference it from 'bootcmd'. It is up to users whether to override 'bootcmd'. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Convert CONFIG_FLASH_CFI_DRIVER et al to KconfigAdam Ford2018-10-191-3/+0
| | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: uniphier: increase CONFIG_SYS_MONITOR_LEN againMasahiro Yamada2018-09-111-2/+2
| | | | | | | | | | | | With the migration to distro-boot, the size of the U-Boot proper image for uniphier_v7_defconfig exceeded the current limit, 576KB. Increase it to 832KB. CONFIG_SYS_UBOOT_BASE must be moved as well to avoid the image over-wrap because the boot ROM of Pro4, Pro5, PXs2/LD6b loads the SPL to the physical address 0x100000. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini2018-08-161-1/+0
| | | | | | | | | | | We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: uniphier: enable distro bootMasahiro Yamada2018-07-251-44/+40
| | | | | | | | | | | | | | | | | | | | Switch to the distro boot for UniPhier platform. - Remove the environment vairalbes used to load images from raw block devices. - Keep the command to download images via tftp. This will be useful to boot the kernel when no valid kernel image is ready yet in the file system. - Use root.cpio.gz instead of root.cpio.uboot because we always know the file size of the init ramdisk; it is loaded via either a file system or network. - Rename fit_addr_r to kernel_addr_r, which the distro command checks to get the load address of FIT image. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Convert CONFIG_MTD_PARTITIONS et al to KconfigAdam Ford2018-07-221-1/+0
| | | | | | | | This converts the following to Kconfig: CONFIG_MTD_PARTITIONS CONFIG_MTD_DEVICE Signed-off-by: Adam Ford <aford173@gmail.com>
* ARM: uniphier: rename environment variable fdt_file to fdtfileMasahiro Yamada2018-05-231-2/+2
| | | | | | | | | For booting Linux in the generic distro mechanism, cmd/pxe.c retrieves the FDT file name from "fdtfile" environment variable. Rename "fdt_file" to "fdtfile" for easier migration to distro boot. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini2018-05-071-2/+1
| | | | | | | | | | | | | | | | | | | | When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: uniphier: move SPL stack addressMasahiro Yamada2018-04-241-1/+1
| | | | | | | | | | | | | | Currently, the address region, 0xf8000 - 0x100000, is used for SPL stack for the 32bit SoCs. Because the U-Boot proper image starts from 0x70000, the maximum size of the U-Boot proper image is 544KB (0x70000 - 0xf8000) for the NOR boot mode. Now uniphier_v7_defconfig is almost hitting this size limit. Changing CONFIG_SPL_STACK can raise the size limit with less impact. With this, the size limit will increase to 576KB (0x70000 - 0x100000). If we need to increase it even more, we would be able to change CONFIG_SYS_UBOOT_BASE at the cost of the flashing command changes. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: select a correct mmc device before flashing imagesMasahiro Yamada2018-04-241-0/+1
| | | | | | | | | Some boards support an SD card and an eMMC device at the same time. Since both belong to 'mmc', they are identified by a device number. When the device number of the eMMC is 1 instead 0, "mmc dev" command must be performed to switch the target device before flashing images. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: increase CONFIG_SYS_MONITOR_LENMasahiro Yamada2018-04-241-1/+1
| | | | | | | | With the recent changes, the size of the U-Boot proper image for uniphier_v7_defconfig exceeded the current limit, 512KB, then SPL fails to load the whole of the U-Boot proper. Increase the size. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Convert all of CONFIG_CONS_INDEX to KconfigTom Rini2018-03-161-2/+0
| | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: uniphier: change load addresses for bigger kernel imageMasahiro Yamada2018-03-151-8/+8
| | | | | | | | | | The kernel size is getting bigger and bigger. Because the Android common kernel is even bigger than the vanilla one, so images overlap in the current memory layout. Adjust the load address for a bigger kernel image. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: increase the firmware size in update command environmentMasahiro Yamada2018-03-151-3/+3
| | | | | | | If a bigger EL32 is used, fip.bin can be larger than the currently assumed boot firmware size. Adjust the update commands. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Convert CONFIG_BOOTP_BOOTPATH et al to KconfigAdam Ford2018-02-231-5/+0
| | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Migrate CONFIG_SPL_FRAMEWORKTom Rini2018-02-141-2/+0
| | | | | | | | | | Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the current set of options we have in Kconfig. We will need to have some options available for SPL and !SPL_FRAMEWORK so this is important. In a few cases we re-order existing options so that we have less escapes from the SPL_FRAMEWORK guard. Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: uniphier: hide memory top by platform hook instead of CONFIGMasahiro Yamada2018-01-091-2/+0
| | | | | | | I do not see a good reason to do this by a CONFIG option that affects all SoCs. The ram_size can be adjusted by dram_init() at run-time. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Move CONFIG_PANIC_HANG to KconfigMasahiro Yamada2017-12-261-2/+0
| | | | | | | | Freescale (NXP) boards have lots of defconfig files per board. I used "imply PANIC_HANG" for them. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: York Sun <york.sun@nxp.com>
* ARM: uniphier: remove unused NAND CONFIG optionsMasahiro Yamada2017-11-291-5/+0
| | | | | | The Denali NAND driver does not use these options any more. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: remove verify=n from environmentsMasahiro Yamada2017-10-231-1/+0
| | | | | | | If the environment "verify" is set to n, the image verification is entirely skipped. Remove it as a preparation for verified boot. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: increase CONFIG_SYS_BOOTM_LEN to 32MBMasahiro Yamada2017-10-231-0/+1
| | | | | | | | | | The default value of CONFIG_SYS_BOOTM_LEN, 0x800000, causes error when uncompressing Image.gz out of FIT image. Uncompressing Kernel Image ... Error: inflate() returned -5 Image too large: increase CONFIG_SYS_BOOTM_LEN Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* net: Add SMC911X driver to Kconfig, convertAdam Ford2017-10-201-8/+0
| | | | | | | | | | | | | We add the various SMC91XX symbols to drivers/net/Kconfig and then this converts the following to Kconfig: CONFIG_SMC911X CONFIG_SMC911X_BASE CONFIG_SMC911X_16_BIT CONFIG_SMC911X_32_BIT Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Apply to the rest of the tree, re-squash old and new patch] Signed-off-by: Tom Rini <trini@konsulko.com>
* include/configs: drop default definitions of CONFIG_SYS_MAXARGSThomas Petazzoni2017-09-031-1/+0
| | | | | | | | | Now that include/config_fallbacks.h define a sane fallback for CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all configurations that were using the default value. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* include/configs: drop default definitions of CONFIG_SYS_PBSIZEThomas Petazzoni2017-09-031-2/+0
| | | | | | | | | Now that the fallback value of CONFIG_SYS_PBSIZE in include/config_fallbacks.h has been adjusted, remove its definition from a large number of board configuration files. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* Kconfig: Add EEPROM options to Kconfig when I2C_EEPROM is setAdam Ford2017-09-021-2/+0
| | | | | | | | | | | | | | | | | | Add the following options to drivers/misc/Kconfig: SYS_I2C_EEPROM_ADDR SYS_I2C_EEPROM_BUS SYS_EEPROM_SIZE SYS_EEPROM_PAGE_WRITE_BITS SYS_EEPROM_PAGE_WRITE_DELAY_MS SYS_I2C_EEPROM_ADDR_LEN SYS_I2C_EEPROM_ADDR_OVERFLOW This does not migrate any boards, but provides a foundations for those who want/need these options Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Migrate uniphier] Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: uniphier: remove unneeded NAND config optionsMasahiro Yamada2017-08-301-3/+0
| | | | | | | | CONFIG_NAND_DENALI select's CONFIG_SYS_NAND_SELF_INIT, so the NAND initialization process is driven by the driver itself. CONFIG_SYS_NAND_MAX_CHIPS and CONFIG_SYS_NAND_BASE are unused. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: remove sLD3 SoC supportMasahiro Yamada2017-08-201-7/+1
| | | | | | This SoC is too old. It is difficult to maintain any longer. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* configs: Remove CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS in all boardsBin Meng2017-07-281-3/+0
| | | | | | | | | | Now that xHCD does not use CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS, remove it in all boards' config files. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
* ARM: uniphier: remove SPL support for ARMv8 SoCsMasahiro Yamada2017-07-261-33/+3
| | | | | | | | | | | It has been a while since ARM Trusted Firmware supported UniPhier SoC family. U-Boot SPL was intended as a temporary loader that runs in secure world. It is a maintenance headache to support two different boot mechanisms. Secure firmware is realm of ARM Trusted Firmware and now U-Boot only serves as a non-secure boot loader for UniPhier ARMv8 SoCs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to KconfigSimon Glass2017-07-251-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
* Kconfig: Migrate FS_FAT / FAT_WRITETom Rini2017-06-031-1/+0
| | | | | | | | Now that these symbols are in Kconfig, migrate all users. Use imply on a number of platforms that default to having this enabled. As part of this we must migrate some straglers for CMD_FAT and DOS_PARTITION. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SPL_BOARD_INIT to KconfigLey Foon Tan2017-05-221-2/+0
| | | | | | | | | This converts the following to Kconfig: CONFIG_SPL_BOARD_INIT Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> [trini: Update the Kconfig logic] Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: uniphier: move kernel physical base to 0x82080000Masahiro Yamada2017-05-171-1/+1
| | | | | | | | | | Reserve enough space below the kernel base. The assumed address map is: 80000000 - 80ffffff : for IPP 81000000 - 81ffffff : for ARM secure 82000000 - : for Linux Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: add usbupdate commandMasahiro Yamada2017-05-171-0/+5
| | | | | | | This script command will be useful to update boot images in the USB storage. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Kconfig: Migrate CONFIG_BAUDRATEPhilipp Tomsich2017-03-191-1/+0
| | | | | | | | Move this in to Kconfig with a default of 115200. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> [trini: Run moveconfig.py, reword commit slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: uniphier: rename second stage loader nameMasahiro Yamada2017-02-231-1/+1
| | | | | | | | | For the memory footprint reason, the Boot ROM can not load the ARM Trusted Firmware BL1 directly when Trusted Board Boot is enabled. The second stage loader is Socionext's own firmware, so rename it for clarification. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* flash: complete CONFIG_SYS_NO_FLASH move with renamingMasahiro Yamada2017-02-121-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is not completed. Finish this work by the tool. During this move, let's rename it to CONFIG_MTD_NOR_FLASH. Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH" than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will make the code more readable. Besides, negative meaning symbols do not fit in obj-$(CONFIG_...) style Makefiles. This commit was created as follows: [1] Edit "default n" to "default y" in the config entry in common/Kconfig. [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH" [3] Rename the instances in defconfigs by the following: find . -path './configs/*_defconfig' | xargs sed -i \ -e '/CONFIG_SYS_NO_FLASH=y/d' \ -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/' [4] Change the conditionals by the following: find . -name '*.[ch]' | xargs sed -i \ -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \ -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \ -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \ -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/' [5] Modify the following manually - Rename the rest of instances - Remove the description from README - Create the new Kconfig entry in drivers/mtd/Kconfig - Remove the old Kconfig entry from common/Kconfig - Remove the garbage comments from include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
generated by cgit (git 2.34.1) at 2024-11-19 20:44:23 +0000