summaryrefslogtreecommitdiffstats
path: root/include/configs/sheevaplug.h
Commit message (Collapse)AuthorAgeFilesLines
* Convert CONFIG_CMD_ASKENV et al to KconfigTom Rini2020-06-041-12/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_CMD_ASKENV CONFIG_CMD_BMP CONFIG_CMD_BOOTD CONFIG_CMD_CACHE CONFIG_CMD_CRC32 CONFIG_CMD_DHCP CONFIG_CMD_ENV CONFIG_CMD_EXPORTENV CONFIG_CMD_EXT2 CONFIG_CMD_EXT4 CONFIG_CMD_FLASH CONFIG_CMD_FS_GENERIC CONFIG_CMD_FUSE CONFIG_CMD_GPIO CONFIG_CMD_GPT CONFIG_CMD_GREPENV CONFIG_CMD_I2C CONFIG_CMD_IMLS CONFIG_CMD_IMPORTENV CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_CMD_MEMINFO CONFIG_CMD_MII CONFIG_CMD_MTDPARTS CONFIG_CMD_NAND CONFIG_CMD_NAND_TRIMFFS CONFIG_CMD_NFS CONFIG_CMD_PCA953X CONFIG_CMD_PCA953X_INFO CONFIG_CMD_PCI CONFIG_CMD_PING CONFIG_CMD_READ CONFIG_CMD_SF CONFIG_CMD_SPI CONFIG_CMD_SPL CONFIG_CMD_SPL_WRITE_SIZE CONFIG_CMD_TIME CONFIG_CMD_TRACE CONFIG_CMD_UBI CONFIG_CMD_UBIFS CONFIG_CMD_UNZIP CONFIG_FS_EXT4 Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_BZIP2 et al to KconfigTom Rini2020-06-041-1/+0
| | | | | | | | | | | | This converts the following to Kconfig: CONFIG_BZIP2 CONFIG_GZIP CONFIG_LZO CONFIG_ZLIB CONFIG_LZMA CONFIG_LZO Signed-off-by: Tom Rini <trini@konsulko.com>
* env: Finish migration of common ENV optionsTom Rini2019-11-201-6/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
* Convert CONFIG_MTD_PARTITIONS et al to KconfigAdam Ford2018-07-221-2/+0
| | | | | | | | This converts the following to Kconfig: CONFIG_MTD_PARTITIONS CONFIG_MTD_DEVICE Signed-off-by: Adam Ford <aford173@gmail.com>
* ARM: kirkwood: Enforce size limit for sheevaplugChris Packham2018-06-051-0/+5
| | | | | | | | | The u-boot binary sits in flash immediately before the environment. Don't allow the binary size to grow into the environment space. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* configs: remove CONFIG_SYS_MVFSChris Packham2018-05-291-1/+3
| | | | | | | | | | | | | This was being used by some Marvell boards to enable some file system related features (many of which have already been moved to Kconfig). Make the future migration of the final 2 or 3 config options easier by expanding #define CONFIG_SYS_MVFS into the options that it enables and remove CONFIG_SYS_MVFS. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini2018-05-071-2/+1
| | | | | | | | | | | | | | | | | | | | When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: Drop unreferenced CONFIG_MACH_* definesTuomas Tynkkynen2018-01-101-1/+0
| | | | | | | | | | | | | | | | | | | | | | These macros are all defined once and never checked or used anywhere: CONFIG_MACH_ASPENITE CONFIG_MACH_DAVINCI_CALIMAIN CONFIG_MACH_DOCKSTAR CONFIG_MACH_EDMINIV2 CONFIG_MACH_GOFLEXHOME CONFIG_MACH_GONI CONFIG_MACH_GURUPLUG CONFIG_MACH_KM_KIRKWOOD CONFIG_MACH_OPENRD_BASE CONFIG_MACH_SHEEVAPLUG Almost all of them were only used for the mach_is_foo() logic in arch/arm/asm/mach-types.h that were dropped in commit f9dadaef8b75fa ("arm: Re-sync asm/mach-types.h with Linux Kernel v4.9") Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
* Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULTTom Rini2017-11-051-11/+1
| | | | | | | | | | We move all instances of CONFIG_MTDIDS_DEFAULT and CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files. There's a few cases here where we need to expand upon what was in the header file. Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to KconfigSimon Glass2017-07-251-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
* Kconfig: Add a CONFIG_IDE optionSimon Glass2017-05-221-2/+2
| | | | | | | | | | | At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate CONFIG_IDE option so that IDE support can be enabled without requiring the 'ide' command. Update existing users and move the ide driver into drivers/block since it should not be in common/. Signed-off-by: Simon Glass <sjg@chromium.org>
* mmc: move CONFIG_GENERIC_MMC to KconfigMasahiro Yamada2017-01-311-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC. Let's create an entry for "config GENERIC_MMC" with "default MMC", then convert all macro defines in headers to Kconfig. Almost all of the defines will go away. I see only two exceptions: configs/blanche_defconfig configs/sandbox_noblk_defconfig They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something might be wrong with these two boards, so should be checked later. Anyway, this is the output of the moveconfig tool. This commit was created as follows: [1] create a config entry in drivers/mmc/Kconfig [2] tools/moveconfig.py -r HEAD GENERIC_MMC [3] manual clean-up of garbage comments in doc/README.* and include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* disk: convert CONFIG_DOS_PARTITION to KconfigPatrick Delaunay2017-01-281-1/+0
| | | | | Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
* mmc: complete unfinished move of CONFIG_MMCMasahiro Yamada2016-12-291-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | Commit 7a777f6d6f35 ("mmc: Add generic Kconfig option") created a Kconfig entry for this option without any actual moves, then commit 44c798799f66 ("sunxi: Use Kconfig CONFIG_MMC") moved instances only for SUNXI. We generally do not like such partial moves. This kind of work is automated by tools/moveconfig.py, so it is pretty easy to complete this move. I am adding "default ARM || PPC || SANDBOX" (suggested by Tom). This shortens the configs and will ease new board porting. This commit was created as follows: [1] Edit Kconfig (remove the "depends on", add the "default", copy the prompt and help message from Linux) [2] Run 'tools/moveconfig.py -y -s -r HEAD MMC' Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
* Kconfig: Move config IDENT_STRING to KconfigSiva Durga Prasad Paladugu2016-09-201-5/+0
| | | | | | | | | Move the config IDENT_STRING to Kconfig and migrate all boards [sivadur: Migrate zynq boards] Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> [trini: Update configs, add some default to sunxi Kconfig] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Re-sync with cmd/KconfigTom Rini2016-04-251-1/+0
| | | | | | | Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
* include/configs: Whitespace fixupTom Rini2016-04-251-1/+0
| | | | | | | A number of moveconfig.py runs have left a instances of multiple empty lines in a row. Correct this to a single empty line. Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: sheevaplug: correct nand partition layoutPeter Korsgaard2016-03-241-3/+3
| | | | | | | | | | | | | | | | | | | | | Commit 1e3d640316 (ARM: sheevaplug: redefine MTDPARTS) changed the partition layout (without any description why), but didn't change the offset/size to load the kernel from or the root=/dev/mtdblockX in the bootargs. The 3MB forseen for a kernel is furthermore too little. A 4.4 build of mvebu_v5_defconfig is 3.6MB: -rw-r--r-- 1 peko peko 3.6M Jan 16 20:24 uImage.kirkwood-sheevaplug When device tree support for sheevaplug was added to the kernel in commit ee514b381e (ARM: Kirkwood: Add dts files for Sheevaplug and eSATA Sheevaplug) a default flash partition layout (used if mtdparts= isn't passed on the command line / CONFIG_MTD_CMDLINE_PARTS isn't enabled) with 1MB for u-boot / environment, 4MB for the kernel and the rest for the rootfs, so use that layout here and adjust the kernel loading to match. Signed-off-by: Peter Korsgaard <peter@korsgaard.com> Signed-off-by: Stefan Roese <sr@denx.de>
* ARM: sheevaplug: drop unneded 'usb start' from boot commandPeter Korsgaard2016-03-141-1/+1
| | | | | | | | The default bootcommand executes x_bootcmd_usb AFTER loading a kernel from nand and just before executing it, which only slows down boot without adding any functionality - So drop it. Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
* ARM: sheevaplug: unbreak kernel bootargs / mtdparts command by dropping ↵Peter Korsgaard2016-03-141-1/+1
| | | | | | | | | | | | | double mtdparts= Commit 1e3d640316 (ARM: sheevaplug: redefine MTDPARTS) prepended mtdparts= to the flash partition information in CONFIG_MTDPARTS, but it is used like "mtdparts=" CONFIG_MTDPARTS - So we end up passing mtdparts=mtdparts=.. to the kernel, confusing the cmdline partition parser. Fix it by dropping the double 'mtdparts='. Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
* ARM: sheevaplug: unbreak default environmentPeter Korsgaard2016-03-141-1/+1
| | | | | | | | | | | Commit 1e3d640316 (ARM: sheevaplug: redefine MTDPARTS) changed the mtdparts part of the default environment, but dropped the trailing zero termination - So the definition of x_bootcmd_kernel becomes part of the x_bootargs variable. Fix it by reintroducing the zero termination. Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
* arm: kirkwood: Move common definitions into common fileQuentin Armitage2015-11-171-38/+2
| | | | | | | | Create include/configs/mv-plug-common.h for common definitions for Sheevaplug, Guruplug and Dreamplug. This will make it easier to ensure the built u-boots stay in track with each other Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
* arm: kirkwood: Use common definition for filesystemsQuentin Armitage2015-11-171-15/+10
| | | | | | | include/configs/mv-common.h brings in the required filesystems if CONFIG_SYS_MVFS is defined, so use it for Sheevaplug and Guruplug. Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
* arm: kirkwood: Move configuration of some commands to _defconfig filesQuentin Armitage2015-11-171-9/+0
| | | | | | | | | | | | For Marvell plugs, move the configuration of DHCP, NAND/SF, PING and USB commands, and HUSH_PARSER into the _defconfig file, rather than the include/configs/*plug.h files. This avoids compiler warnings of duplicate definitions if the option is selected in the .config, but also defined in the include/configs/*plug.h file. Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
* arm: kirkwood: standardise the configurationQuentin Armitage2015-11-171-0/+13
| | | | | | | | | | | | | The Marvell plugs are very similar systems, and so it makes sense for their u-boots to have the same commands/configuration. Add EXT4 and MII to Dreamplug, DATE to Guruplug and Sheevaplug. Add CONFIG_SYS_ALT_MEMTEST to Sheevaplug. There are still command differences around NAND, SPI/NOR. Also default to building u-boot.kwb for Sheevaplug and Guruplug. Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
* arm, powerpc: select SYS_GENERIC_BOARDMasahiro Yamada2015-10-241-1/+0
| | | | | | | | | | | We have finished Generic Board conversion for ARM and PowerPC, i.e. all the boards have been converted except OpenRISC, SuperH, SPARC, which have not supported Generic Board framework yet. Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro defines in include/configs/*.h. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Move defaults from config_cmd_default.h to KconfigJoe Hershberger2015-06-251-1/+0
| | | | | | | | | | This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini <trini@konsulko.com>
* kirkwood: sheevaplug: add FDT supportDrEagle2015-02-061-0/+5
| | | | | | | LIBFDT feature is required to support new kernels. Signed-off-by: Gérald Kerma <drEagle@doukki.net> Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
* kirkwood: sheevaplug: fix multiple definesDrEagle2015-02-061-1/+0
| | | | | Signed-off-by: Gérald Kerma <drEagle@doukki.net> Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
* kirkwood: sheevaplug: fix styleDrEagle2015-02-061-0/+1
| | | | | Signed-off-by: Gérald Kerma <drEagle@doukki.net> Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
* kirkwood: sheevaplug: add CONFIG_SYS_GENERIC_BOARD defineLuka Perkov2015-01-251-0/+2
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> Acked-by: Stefan Roese <sr@denx.de> CC: Prafulla Wadaskar <prafulla@marvell.com>
* ARM: sheevaplug: add HUSH parserDrEagle2014-10-011-0/+5
| | | | | | | | | | This patch add HUSH command parser Signed-off-by: Gerald Kerma <drEagle@doukki.net> Changes in v1: - add HUSH command parser Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* ARM: sheevaplug: redefine MTDPARTSDrEagle2014-10-011-2/+4
| | | | | | | | | | This patch redefine MTDPARTS Signed-off-by: Gerald Kerma <drEagle@doukki.net> Changes in v1: - redefine MTDPARTS Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* ARM: sheevaplug: add MTD defaultsDrEagle2014-10-011-0/+5
| | | | | | | | | | This patch add MTDIDS and MTDPARTS defaults settings to sheevaplug Signed-off-by: Gerald Kerma <drEagle@doukki.net> Changes in v1: - add MTDIDS and MTDPARTS default to sheevaplug Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* ARM: sheevaplug: add MVSATA driverDrEagle2014-10-011-1/+25
| | | | | | | | | | | This patch add MVSATA driver to sheevaplug Signed-off-by: Gerald Kerma <drEagle@doukki.net> Changes in v1: - add MVSATA driver to sheevaplug - enable ext4 FS support Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* ARM: sheevaplug: change env locationDrEagle2014-10-011-2/+2
| | | | | | | | | | | | | | | This patch move the environment offset in sheevaplug. The size of the u-boot binary is become too big. Fix saving environments was result of corrupting the u-boot. Signed-off-by: Gerald Kerma <drEagle@doukki.net> Changes in v2: - patch description Changes in v1: - fix sheevaplug environment offset Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* kirkwood: kconfig: refactor Kconfig and defconfigMasahiro Yamada2014-08-301-1/+0
| | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the KirkWood board select menu to kirkwood/Kconfig. Consolidate also common settings (CONFIG_SYS_CPU="arm926ejs" and CONFIG_SYS_SOC="kirkwood"). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Prafulla Wadasdkar <prafulla@marvell.com> Cc: Luka Perkov <luka@openwrt.org>
* ARM: kirkwood: add mvsdio driverDrEagle2014-08-011-0/+11
| | | | | | | | | This patch add Marvell kirkwood MVSDIO/MMC driver and enable it for Sheevaplugs and OpenRD boards. Signed-off-by: Gerald Kerma <drEagle@doukki.net> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-241-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* kirkwood: added common config file mv-common.hPrafulla Wadaskar2010-10-131-101/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | It is observed that, in most of the board configs the code is being duplicated, also for any common change all board files needs update This issue was under discussion from long on mailing list and we converge on introducing common config file. With this patch- 1. Total Kirkwood specific configuration code is reduced by 210 lines 2. All common configuration can be shared by multiple boards 3. Easy to manage common updates like ARM relocation changes mv-common.h file is added to include/configs/ It contains all common configuration supported for all Kirkwood boards The respective board configs are updated for its usage Build tested for guruplug, mv88f6281gtw_ge, openrd_base, rd6281a and sheevaplug Binary execution tested for sheevaplug Todo: 1. Other custom Kirkwood boards to be synced 2. The support to be extended for Orion5X based boards Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* mvgbe: support SoCs other than kirkwoodAlbert Aribaud2010-07-121-2/+2
| | | | | | | | | Rename all references to kirkwood in mvgbe symbols throughout the whole codebase. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* configs/sheevaplug: added a few additional commandsFrans Meulenbroeks2010-04-301-5/+22
| | | | | | | | | | | | | | | | | This patch includes a few additional commands in the sheevaplug version of u-boot: - support for LONGHELP so you can get help messages - auto completion and command editing - ubi and mii support - ext2 filesystem (convenient if you have an ext2 from which you want to boot) - jffs2 and ubifs filesystems (if you want to use these in NAND) This also makes it more similar to openrd client. Side effect of this patch is that the code now needs 3 sectors i.s.o. 2 so an existing env is overwritten Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
* common: delete CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOULHeiko Schocher2009-12-081-1/+0
| | | | | | | | | There is more and more usage of printing 64bit values, so enable this feature generally, and delete the CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL defines. Signed-off-by: Heiko Schocher <hs@denx.de>
* arm: Sheevaplug: Fixed NAND specific warningPrafulla Wadaskar2009-08-091-0/+1
| | | | | | | It is recommended to define the macro CONFIG_SYS_64BIT_VSPRINTF for NAND specific warning removal, same is done in this patch Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* Marvell Sheevaplug Board supportPrafulla Wadaskar2009-07-181-0/+195
Reference: http://plugcomputer.org/ http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support This patch is tested for- 1. Boot from DRAM/NAND flash 2. File transfer using tftp 3. NAND flash read/write/erase 4. Linux kernel and RFS Boot from NAND 5. Enabled USB PHY init for kernel need 6. Boot from USB supported Note: to boot Kirkwood kernel with USB support, you should add "usb start" in the boot sequence Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
generated by cgit (git 2.34.1) at 2024-06-30 14:33:08 +0000