summaryrefslogtreecommitdiffstats
path: root/include/configs/at91sam9x5ek.h
Commit message (Collapse)AuthorAgeFilesLines
* ARM: at91: Convert SPL_GENERATE_ATMEL_PMECC_HEADER to KconfigDerald D. Woods2019-01-211-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | | This commit converts the following items to Kconfig: CONFIG_ATMEL_NAND_HWECC CONFIG_ATMEL_NAND_HW_PMECC CONFIG_PMECC_CAP CONFIG_PMECC_SECTOR_SIZE CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER [PMECC References] https://www.at91.com/linux4sam/bin/view/Linux4SAM/PmeccConfigure https://www.at91.com/linux4sam/bin/view/Linux4SAM/AT91Bootstrap [Mailing List Thread] https://lists.denx.de/pipermail/u-boot/2018-December/350666.html Fixes: 5541543f ("configs: at91: Remove CONFIG_SYS_EXTRA_OPTIONS assignment") [trini: Make the migration be size neutral and possibly not fix the above in all cases] Reported-by: Daniel Evans <photonthunder@gmail.com> Cc: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Derald D. Woods <woods.technical@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: at91: at91sam9x5ek: fix bootcmd for NAND flashEugen.Hristev@microchip.com2018-11-011-2/+3
| | | | | | | | | The default bootcommand needs to be accurate w.r.t the nand memory map at http://www.at91.com/linux4sam/bin/view/Linux4SAM/AT91sam9x5ekMainPage#NAND_Flash_demo_Memory_map Updated to load kernel + dtb at right offsets and boot the zImage. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
* configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini2018-08-161-1/+0
| | | | | | | | | | | We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_MTD_PARTITIONS et al to KconfigAdam Ford2018-07-221-3/+0
| | | | | | | | This converts the following to Kconfig: CONFIG_MTD_PARTITIONS CONFIG_MTD_DEVICE Signed-off-by: Adam Ford <aford173@gmail.com>
* Convert CONFIG_NAND_ATMEL to KconfigAdam Ford2018-07-211-1/+0
| | | | | | | This converts the following to Kconfig: CONFIG_NAND_ATMEL Signed-off-by: Adam Ford <aford173@gmail.com>
* configs: at91: Adjust CONFIG_ENV_OFFSET to match sama5 addressNicolas Ferre2018-05-231-1/+1
| | | | | | | | | | In order to have a single ENV_OFFSET to manage, use the same as the sama5 one. This address matches our NAND flash map available at: http://www.at91.com/linux4sam/bin/view/Linux4SAM/Sama5d3XplainedMainPage#NAND_Flash_demo_Memory_map Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> [eugen.hristev@microchip.com: rework on latest version of u-boot] Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
* SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini2018-05-071-2/+1
| | | | | | | | | | | | | | | | | | | | When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
* spl: spi: Move CONFIG_SPL_SPI_LOAD to KconfigMarek Vasut2018-04-111-1/+0
| | | | | | | | Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all configurations using it to Kconfig. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com>
* Convert CONFIG_BOOTP_BOOTPATH et al to KconfigAdam Ford2018-02-231-7/+0
| | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Migrate CONFIG_SPL_FRAMEWORKTom Rini2018-02-141-1/+0
| | | | | | | | | | Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the current set of options we have in Kconfig. We will need to have some options available for SPL and !SPL_FRAMEWORK so this is important. In a few cases we re-order existing options so that we have less escapes from the SPL_FRAMEWORK guard. Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Migrate CONFIG_SYS_TEXT_BASETom Rini2018-02-111-2/+0
| | | | | | | | | | | On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
* board: at91sam9x5ek: Convert to CONFIG_DM_VIDEOWenyou Yang2017-09-291-10/+0
| | | | | | | | Convert the board to support the video driver model, add the device tree node, and remove the unnecessary code. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* configs: at91: Remove CONFIG_SYS_EXTRA_OPTIONS assignmentWenyou Yang2017-09-141-13/+10
| | | | | | | | To remove the assignment of CONFIG_SYS_EXTRA_OPTIONS option, which is deprecated, use the CONFIG_XXXX_BOOT options to indicate the boot media, and the SoC is selected by the board. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
* ARM: at91: Remove hardware.h included in configsWenyou Yang2017-09-141-2/+0
| | | | | | | | | | As said in READRE.kconfig, include/configs/*.h will be removed after all options are switched to Kconfig. As the first step, remove the follow line from include/configs/*.h. #include <asm/hardware.h> Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
* include/configs: drop default definitions of CONFIG_SYS_MAXARGSThomas Petazzoni2017-09-031-1/+0
| | | | | | | | | Now that include/config_fallbacks.h define a sane fallback for CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all configurations that were using the default value. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* include/configs: remove CONFIG_SYS_CBSIZE when the default value is usedThomas Petazzoni2017-09-031-1/+0
| | | | | | | | | | | Now that include/config_fallbacks.h define a sane fallback for CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all configurations that were using the default value. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Drop <config.h> from stih410-b2260.h] Signed-off-by: Tom Rini <trini@konsulko.com>
* common: Move CONFIG_BOOTARGS to KconfigSam Protsenko2017-08-141-15/+0
| | | | | | | | | Also introduce CONFIG_USE_BOOTARGS option so we can control if CONFIG_BOOTARGS defined at all. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> [trini: Resync r8a779[56]_ulcb, various ls10xx targets] Signed-off-by: Tom Rini <trini@konsulko.com>
* spl: moveconfig: remove SPL_LDSCRIPT definitions for header-filesPhilipp Tomsich2017-08-131-1/+0
| | | | | | | | | With the hierarchical defaults set up, we remove these from the header files. To do so, I've run moveconfig on SPL_LDSCRIPT and this commits the changes. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* configs: Migrate CMD_NAND*Tom Rini2017-07-311-11/+4
| | | | | | | | | | Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the defconfig files. Tested-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* env: Migrate CONFIG_ENV_IS_IN_FAT options to KconfigTom Rini2017-07-311-3/+0
| | | | | | | | We rename the various FAT_ENV_xxx options to CONFIG_ENV_FAT_xxx so that they can be modified via Kconfig. Migrate all existing users to the new values. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_ENV_IS_IN_FAT to KconfigSimon Glass2017-07-251-1/+0
| | | | | | | This converts the following to Kconfig: CONFIG_ENV_IS_IN_FAT Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_ENV_IS_IN_SPI_FLASH to KconfigSimon Glass2017-07-251-2/+0
| | | | | | | This converts the following to Kconfig: CONFIG_ENV_IS_IN_SPI_FLASH Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to KconfigSimon Glass2017-07-251-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Migrate RBTREE, LZO, CMD_MTDPARTS, CMD_UBI and CMD_UBIFSTom Rini2017-07-241-4/+0
| | | | | | | | The above CONFIG options are in Kconfig, and now have correct depends and inter-dependencies. Migrate these to configs/ from include/configs/. In the case of CMD_UBIFS also change it to be a default y if CMD_UBI. Signed-off-by: Tom Rini <trini@konsulko.com>
* Kconfig: Migrate FS_FAT / FAT_WRITETom Rini2017-06-031-1/+0
| | | | | | | | Now that these symbols are in Kconfig, migrate all users. Use imply on a number of platforms that default to having this enabled. As part of this we must migrate some straglers for CMD_FAT and DOS_PARTITION. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SPL_BOARD_INIT to KconfigLey Foon Tan2017-05-221-1/+0
| | | | | | | | | This converts the following to Kconfig: CONFIG_SPL_BOARD_INIT Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> [trini: Update the Kconfig logic] Signed-off-by: Tom Rini <trini@konsulko.com>
* Kconfig: USB: Migrate CONFIG_USB_EHCI to CONFIG_USB_EHCI_HCDTom Rini2017-05-151-2/+2
| | | | | | | | | | In order to be able to migrate the various SoC EHCI CONFIG options we first need to finish the switch from CONFIG_USB_EHCI to CONFIG_USB_EHCI_HCD. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Marek Vasut <marex@denx.de>
* configs: at91sam9x5ek: Update to support DM/DTWenyou Yang2017-05-091-24/+3
| | | | | | | | | | | | Update the configuration files to support the device tree and driver model. The device clock and pins configuration are handled by the clock and the pinctrl drivers respectively. Because the limitation of internal SRAM size, the SPL with driver model can't be supported, disable the SPL option. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_SYS_WHITE_ON_BLACK to KconfigSimon Glass2017-04-301-1/+0
| | | | | | | | | This converts the following to Kconfig: CONFIG_SYS_WHITE_ON_BLACK Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Make this default y on various SoCs] Signed-off-by: Tom Rini <trini@konsulko.com>
* Kconfig: Migrate CONFIG_BAUDRATEPhilipp Tomsich2017-03-191-2/+0
| | | | | | | | Move this in to Kconfig with a default of 115200. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> [trini: Run moveconfig.py, reword commit slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
* flash: complete CONFIG_SYS_NO_FLASH move with renamingMasahiro Yamada2017-02-121-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is not completed. Finish this work by the tool. During this move, let's rename it to CONFIG_MTD_NOR_FLASH. Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH" than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will make the code more readable. Besides, negative meaning symbols do not fit in obj-$(CONFIG_...) style Makefiles. This commit was created as follows: [1] Edit "default n" to "default y" in the config entry in common/Kconfig. [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH" [3] Rename the instances in defconfigs by the following: find . -path './configs/*_defconfig' | xargs sed -i \ -e '/CONFIG_SYS_NO_FLASH=y/d' \ -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/' [4] Change the conditionals by the following: find . -name '*.[ch]' | xargs sed -i \ -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \ -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \ -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \ -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/' [5] Modify the following manually - Rename the rest of instances - Remove the description from README - Create the new Kconfig entry in drivers/mtd/Kconfig - Remove the old Kconfig entry from common/Kconfig - Remove the garbage comments from include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* mmc: move CONFIG_GENERIC_MMC to KconfigMasahiro Yamada2017-01-311-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC. Let's create an entry for "config GENERIC_MMC" with "default MMC", then convert all macro defines in headers to Kconfig. Almost all of the defines will go away. I see only two exceptions: configs/blanche_defconfig configs/sandbox_noblk_defconfig They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something might be wrong with these two boards, so should be checked later. Anyway, this is the output of the moveconfig tool. This commit was created as follows: [1] create a config entry in drivers/mmc/Kconfig [2] tools/moveconfig.py -r HEAD GENERIC_MMC [3] manual clean-up of garbage comments in doc/README.* and include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* disk: convert CONFIG_DOS_PARTITION to KconfigPatrick Delaunay2017-01-281-5/+0
| | | | | Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
* Convert CONFIG_BOARD_EARLY_INIT_F to KconfigSimon Glass2017-01-251-1/+0
| | | | | | | This converts the following to Kconfig: CONFIG_BOARD_EARLY_INIT_F Signed-off-by: Simon Glass <sjg@chromium.org>
* mmc: complete unfinished move of CONFIG_MMCMasahiro Yamada2016-12-291-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | Commit 7a777f6d6f35 ("mmc: Add generic Kconfig option") created a Kconfig entry for this option without any actual moves, then commit 44c798799f66 ("sunxi: Use Kconfig CONFIG_MMC") moved instances only for SUNXI. We generally do not like such partial moves. This kind of work is automated by tools/moveconfig.py, so it is pretty easy to complete this move. I am adding "default ARM || PPC || SANDBOX" (suggested by Tom). This shortens the configs and will ease new board porting. This commit was created as follows: [1] Edit Kconfig (remove the "depends on", add the "default", copy the prompt and help message from Linux) [2] Run 'tools/moveconfig.py -y -s -r HEAD MMC' Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
* spl: Remove CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORSSemen Protsenko2016-11-181-1/+0
| | | | | | This option isn't used for anything, so get rid of it. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
* spl: Convert CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to KconfigSemen Protsenko2016-11-181-1/+0
| | | | | | Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> [trini: Fix sniper and kc1 migration] Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_CONSOLE_IS_IN_ENV and CONFIG_CONSOLE_MUX to KconfigSimon Glass2016-10-231-1/+0
| | | | | | | | | | This converts the following to Kconfig: CONFIG_SYS_CONSOLE_IS_IN_ENV CONFIG_CONSOLE_MUX Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Re-order, re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_LCD to KconfigSimon Glass2016-10-231-1/+0
| | | | | | | | | This converts the following to Kconfig: CONFIG_LCD Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
* common/Kconfig: Add DISPLAY_CPUINFOLokesh Vutla2016-10-121-1/+0
| | | | | | | | Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default in certain architectures. Migrate all config files. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* kconfig: introduce kconfig for UBIHeiko Schocher2016-09-261-1/+0
| | | | | | | | | move the UBI config options into Kconfig. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andrew F. Davis <afd@ti.com> Reviewed by: Evgeni Dobrev <evgeni at studio-punkt.com>
* Convert CONFIG_SPL_SPI_SUPPORT to KconfigSimon Glass2016-09-161-1/+0
| | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_SPL_SPI_FLASH_SUPPORT to KconfigSimon Glass2016-09-161-1/+0
| | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_SPL_SERIAL_SUPPORT to KconfigSimon Glass2016-09-161-2/+0
| | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_SPL_NAND_SUPPORT to KconfigSimon Glass2016-09-161-1/+0
| | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_SPL_MMC_SUPPORT to KconfigSimon Glass2016-09-161-1/+0
| | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_SPL_LIBGENERIC_SUPPORT to KconfigSimon Glass2016-09-161-1/+0
| | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_SPL_LIBDISK_SUPPORT to KconfigSimon Glass2016-09-161-1/+0
| | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_SPL_LIBCOMMON_SUPPORT to KconfigSimon Glass2016-09-161-1/+0
| | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_SPL_GPIO_SUPPORT to KconfigSimon Glass2016-09-161-1/+0
| | | | | | Move this option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2024-11-19 09:26:24 +0000