summaryrefslogtreecommitdiffstats
path: root/drivers/watchdog
Commit message (Collapse)AuthorAgeFilesLines
* imx_watchdog: Do not assert WDOG_B on watchdog initRoss Parker2016-10-041-1/+1
| | | | | | | | Currently the driver asserts WDOG_B by clearing WCR_WDA bit when enabling the watchdog. Do not clear WCR_WDA. Signed-off-by: Ross Parker <rossjparker@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
* imx_watchdog: add weak attribute to reset_cpu functionStefan Agner2016-07-191-1/+1
| | | | | | | This allows to overwrite reset_cpu function in case a board level reset is preferred (e.g. through PMIC). Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
* imx_watchdog: always set minimal timeout in reset_cpuAndrey Skvortsov2016-01-071-1/+1
| | | | | | | | | The problem is that timeout bits in WCR register were leaved unchanged. So previously set timeout value was applied and therefore 'reset' command takes any value up to two minutes, depending on previous watchdog settings, instead of minimal 0.5 seconds. Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
* ls102xa: Fix reset hangFabio Estevam2015-10-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | Since commit 623d96e89aca6("imx: wdog: correct wcr register settings") issuing a 'reset' command causes the system to hang. Unlike i.MX and Vybrid, the watchdog controller on LS102x is big-endian. This means that the watchdog on LS1021 has been working by accident as it does not use the big-endian accessors in drivers/watchdog/imx_watchdog.c. Commit 623d96e89aca6("imx: wdog: correct wcr register settings") only revelead the endianness problem on LS102x. In order to fix the reset hang, introduce a reset_cpu() implementation that is specific for ls102x, which accesses the watchdog WCR register in big-endian format. All that is required to reset LS102x is to clear the SRS bit. This approach is a temporary workaround to avoid a regression for LS102x in the 2015.10 release. The proper fix is to make the watchdog driver endian-aware, so that it can work for i.MX, Vybrid and LS102x. Reported-by: Sinan Akman <sinan@writeme.com> Tested-by: Sinan Akman <sinan@writeme.com> Reviewed-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* imx_watchdog: Add a header file for watchdog registersFabio Estevam2015-10-121-13/+1
| | | | | | | | | Create fsl_wdog.h to store the watchdog registers and bit fields. This can be useful when accesses to the watchdog block are made from other parts, such as arch/arm/ cpu code. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* imx: wdog: correct wcr register settingsPeng Fan2015-09-201-1/+2
| | | | | | | | | | | | | We should not simple use "writew(WCR_WDE, &wdog->wcr)" to set wcr, since this will override bits set before reset_cpu. Use clrsetbits_le16 instead of writew to fix this issue. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Sebastian Siewior <bigeasy@linutronix.de> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* imx: imx7d: add imx-common cpu support for imx7dAdrian Alonso2015-09-131-1/+1
| | | | | | | | | Add imx-common cpu support for imx7d SoC - Update reset_cause for imx7d - Enable watchdog driver built for imx7d Signed-off-by: Adrian Alonso <aalonso@freescale.com> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* watchdog/imx_watchdog: do not set WCR_WDWSebastian Siewior2015-03-251-2/+1
| | | | | | | | | | | | | | with WCR_WDW set, the watchdog won't trigger if we bootet linux and idle around while the watchdog is not triggered. It seems the timer makes progress very slowly if at all. I managed to remain 20minutes alive while the timeout was set to 60secs. It reboots within 60secs if I start a busyloop in userland (something like "while (1) { }"). While I don't see a reason why the WDT should not be running while the CPU is in idle, I'm dropping this bit. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Stefano Babic <sbabic@denx.de>
* ARM: remove tnetv107x board supportMasahiro Yamada2015-02-242-166/+0
| | | | | | | | This is still a non-generic board. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Chan-Taek Park <c-park@ti.com> Acked-by: Marek Vasut <marex@denx.de>
* arm, at91, wdt: make timeout configurableHeiko Schocher2015-02-071-0/+4
| | | | | | | make the HW WDT timeout configurable through the define CONFIG_AT91_HW_WDT_TIMEOUT. Signed-off-by: Heiko Schocher <hs@denx.de>
* kconfig: add blank Kconfig filesMasahiro Yamada2014-09-241-0/+0
| | | | | | | | This would be useful to start moving various config options. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
* arm: ls102xa: Add Freescale LS102xA SoC supportWang Huan2014-09-081-1/+1
| | | | | | | | | | | | | | | | | | The QorIQ LS1 family is built on Layerscape architecture, the industry's first software-aware, core-agnostic networking architecture to offer unprecedented efficiency and scale. Freescale LS102xA is a set of SoCs combines two ARM Cortex-A7 cores that have been optimized for high reliability and pack the highest level of integration available for sub-3 W embedded communications processors with Layerscape architecture and with a comprehensive enablement model focused on ease of programmability. Signed-off-by: Alison Wang <alison.wang@freescale.com> Signed-off-by: Jason Jin <jason.jin@freescale.com> Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
* blackfin: Fix warning about undefined functionVasili Galka2014-07-071-0/+1
| | | | | | | get_sclk() was not defined in bfin_wdt.c, include the corresponding header. Cc: Sonic Zhang <sonic.adi@gmail.com> Signed-off-by: Vasili Galka <vvv444@gmail.com>
* watchdog/denali: Adding DesignWare watchdog driver supportChin Liang See2014-07-052-0/+75
| | | | | | | | | | | | To add the DesignWare watchdog driver support. It required information such as register base address and clock info from configuration header file within include/configs folder. Signed-off-by: Chin Liang See <clsee@altera.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
* Merge branch 'iu-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-11-091-1/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
| * imx_watchdog: do not soft-reset while watchdog initAnatolij Gustschin2013-10-311-1/+2
| | | | | | | | | | | | | | | | Currently the driver clears WCR_SRS bit when enabling the watchdog and this causes a software reset. Do not clear WCR_SRS. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* | drivers: convert makefiles to Kbuild styleMasahiro Yamada2013-10-311-30/+8
|/ | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* microblaze: Fix watchdog initializationMichal Simek2013-10-161-4/+2
| | | | | | | | | | | The patch: "blackfin: Move blackfin watchdog driver out of the blackfin arch folder." (sha1: e9a389a18477c1c57a0b30e9ea8f4d38c6e26e63) changed hw_watchdog_init() prototype which didn't match with Microblaze one. This patch fixes the driver and Microblaze initialization. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* Coding Style cleanup: remove trailing white spaceWolfgang Denk2013-10-141-1/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* arm, am335x: add watchdog supportHeiko Schocher2013-08-282-0/+122
| | | | | | | | Add TI OMAP 16xx & 24xx/34xx 32KHz (non-secure) watchdog support. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-246-84/+6
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-06-081-1/+1
|\ | | | | | | | | Conflicts: drivers/serial/Makefile
| * arm: vf610: Add watchdog support for Vybrid VF610Alison Wang2013-06-031-1/+1
| | | | | | | | | | | | This patch adds watchdog support for Vybrid VF610 platform. Signed-off-by: Alison Wang <b18965@freescale.com>
* | blackfin: Move blackfin watchdog driver out of the blackfin arch folder.Sonic Zhang2013-05-132-0/+27
|/ | | | | | | | | | - Enable hw_watchdog_init() in watchdog.h if CONFIG_HW_WATCHDOG is defined. - Move blackfin hw watchdog driver to the generic driver folder. - Call hw_watchdog_init() from blackfin board init code. - Reuse macro CONFIG_WATCHDOG_TIMEOUT_MSECS - Update README.watchdog accordingly Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
* watchdog: Add support for Xilinx Microblaze watchdogMichal Simek2013-04-302-0/+88
| | | | | | | Watchdog can be used on Microblaze, PPC and Zynq hw designs. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
* mx31/mx35/mx51/mx53/mx6: add watchdogTroy Kisky2013-01-132-0/+69
| | | | | | | Use a common watchdog driver for all these cpus. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
* dm: wdt: Move s5p watchdog timer to drivers/watchdog/Marek Vasut2012-11-152-0/+60
| | | | | | | | | Signed-off-by: Marek Vasut <marex@denx.de> Cc: David Müller <d.mueller@elsoft.ch> Cc: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: U-Boot DM <u-boot-dm@lists.denx.de> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* dm: wdt: arm: Move tnetv107x into drivers/watchdog/Marek Vasut2012-10-182-0/+181
| | | | | | | | Signed-off-by: Marek Vasut <marex@denx.de> Cc: Oliver Brown <obrown@adventnetworks.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: U-Boot DM <u-boot-dm@lists.denx.de>
* AT91: fix at91sam_wdt.c to reworked header filesReinhard Meyer2011-05-181-1/+1
| | | | Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
* AT91: fix related at91 driver filesReinhard Meyer2011-05-181-2/+2
| | | | Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
* ftwdt010_wdt: move header to include/faraday and enhanceMacpaul Lin2011-04-122-108/+7
| | | | | | | | | | | | | 1. Move header to include/faraday 2. Fix include path in ftwdt010_wdt.c 3. Fix function prototype and declaration to - ftwdt010_wdt_settimeout - ftwdt010_wdt_reset - ftwdt010_wdt_disable 4. Add "#if definde (CONFIG_HW_WATCHDOG)" let user have flexibilty to choose which better to his product. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
* ftwdt010_wdt: support faraday ftwdt010 watchdogMacpaul Lin2011-04-113-0/+206
| | | | | | | | Faraday ftwdt010 watchdog is an architecture independant watchdog. It is usually used in SoC chip design. Signed-off-by: Macpaul Lin <macpaul@andestech.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
* Switch from archive libraries to partial linkingSebastien Carlier2010-11-171-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | Before this commit, weak symbols were not overridden by non-weak symbols found in archive libraries when linking with recent versions of binutils. As stated in the System V ABI, "the link editor does not extract archive members to resolve undefined weak symbols". This commit changes all Makefiles to use partial linking (ld -r) instead of creating library archives, which forces all symbols to participate in linking, allowing non-weak symbols to override weak symbols as intended. This approach is also used by Linux, from which the gmake function cmd_link_o_target (defined in config.mk and used in all Makefiles) is inspired. The name of each former library archive is preserved except for extensions which change from ".a" to ".o". This commit updates references accordingly where needed, in particular in some linker scripts. This commit reveals board configurations that exclude some features but include source files that depend these disabled features in the build, resulting in undefined symbols. Known such cases include: - disabling CMD_NET but not CMD_NFS; - enabling CONFIG_OF_LIBFDT but not CONFIG_QE. Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
* Convert at91 watchdog driver to new SoC accessAchim Ehrlich2010-04-031-10/+11
| | | | | | | This converts the at91 watchdog driver to new c structure type to access registers of the SoC Signed-off-by: Achim Ehrlich <aehrlich@taskit.de>
* at91sam9: add watchdog supportJean-Christophe PLAGNIOL-VILLARD2009-04-042-0/+125
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
generated by cgit (git 2.34.1) at 2024-11-19 11:24:42 +0000