summaryrefslogtreecommitdiffstats
path: root/drivers/net/Kconfig
Commit message (Collapse)AuthorAgeFilesLines
* net: Introduce DSA class for Ethernet switchesClaudiu Manoil2021-02-161-0/+15
| | | | | | | | | | | | | | | DSA stands for Distributed Switch Architecture and it covers switches that are connected to the CPU through an Ethernet link and generally use frame tags to pass information about the source/destination ports to/from CPU. Front panel ports are presented as regular ethernet devices in U-Boot and they are expected to support the typical networking commands. DSA switches may be cascaded, DSA class code does not currently support this. Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
* net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCsAaron Tseng2021-01-271-0/+7
| | | | | | | | | | | | | Add Cortina Access Ethernet device driver for CAxxxx SoCs. This driver supports both legacy and DM_ETH network models. Signed-off-by: Aaron Tseng <aaron.tseng@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Abbie Chang <abbie.chang@Cortina-Access.com> CC: Tom Rini <trini@konsulko.com>
* net: add ethernet driver for MediaTek MT7620 SoCWeijie Gao2021-01-241-0/+12
| | | | | | | | | | | | | | | | This patch adds ethernet driver for MediaTek MT7620 SoC. The MT7620 SoC has a built-in ethernet (Frame Engine) and a built-in 7-port switch and two xMII interfaces (can be MII/RMII/RGMII). The port 0-3 of the switch connects to intergrited FE PHYs. Port 4 can be configured to connect to either the intergrited FE PHY, or the xMII. Port 5 always connects to the xMII. Port 6 is the CPU port. This driver supports MT7530 giga switch connects to port 5. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
* net: Add IPQ40xx MDIO driverRobert Marko2020-10-221-0/+7
| | | | | | | | This adds the driver for the IPQ40xx built-in MDIO. This will be needed to support future PHY driver. Signed-off-by: Robert Marko <robert.marko@sartura.hr> Cc: Luka Perkov <luka.perkov@sartura.hr>
* net: Add NIC controller driver for OcteonTX2Suneel Garapati2020-10-141-0/+17
| | | | | | | | | Adds support for Network Interface controllers found on OcteonTX2 SoC platforms. Signed-off-by: Suneel Garapati <sgarapati@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com>
* net: Add NIC controller driver for OcteonTXSuneel Garapati2020-10-141-0/+14
| | | | | | | | | Adds support for Network Interface controllers found on OcteonTX SoC platforms. Signed-off-by: Suneel Garapati <sgarapati@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com>
* net, qe: add DM support for QE UEC ethernetHeiko Schocher2020-09-171-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | add DM/DTS support for the UEC ethernet on QUICC Engine Block. Signed-off-by: Heiko Schocher <hs@denx.de> Patch-cc: Mario Six <mario.six@gdsys.cc> Patch-cc: Qiang Zhao <qiang.zhao@nxp.com> Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com> Patch-cc: Madalin Bucur <madalin.bucur@oss.nxp.com> Series-changes: 3 - revert: commit "3374264df97b" ("drivers: net: qe: deselect QE when DM_ETH is enabled") as now qe works with DM and DM_ETH support. - fix mailaddress from Holger Series-changes: 2 - add comments from Qiang Zhao: - add device node documentation - I did not drop the dm_qe_uec_phy.c and use drivers/net/fsl_mdio.c because using drivers/net/fsl_mdio.c leads in none existent udevice mdio@3320 instead boards with DM ETH support should use now this driver. - remove RFC tag Commit-notes: - I let the old none DM based implementation in code so boards should work with old implementation. This Code should be removed if all boards are converted to DM/DTS. - add the DM based qe uec driver under drivers/net/qe - Therefore copied the files uccf.c uccf.h uec.h from drivers/qe. So there are a lot of Codingstyle problems currently. I fix them in next version if this RFC patch is OK or it needs some changes. - The dm based driver code is now under drivers/net/qe/dm_qe_uec.c Used a lot of functions from drivers/qe/uec.c - seperated the PHY specific code into seperate file drivers/net/qe/dm_qe_uec_phy.c END
* xilinx: kconfig: Change Kconfig dependencies for Xilinx driversMichal Simek2020-08-201-3/+3
| | | | | | | | | Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in PL and vice versa. That's why change dependencies and do not limit enabling just for some platforms. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
* net: dwc_eth_qos: add Kconfig option to select supported configurationPatrick Delaunay2020-08-041-3/+24
| | | | | | | | | | | | | | | Add configuration flag to select the supported dwc driver configuration: - CONFIG_DWC_ETH_QOS_TEGRA186 - CONFIG_DWC_ETH_QOS_IMX - CONFIG_DWC_ETH_QOS_STM32 See Linux driver ethernet/stmicro/stmmac and associated glue layers for other configuration examples. This patch removes the not-selected compatibles and lets the linker remove the unused functions to reduce the size of the driver. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
* net: dc2114x: Add Kconfig entriesMarek Vasut2020-07-251-0/+6
| | | | | | | | Add Kconfig entries for the dc2114x driver and convert various boards. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Ramon Fried <rfried.dev@gmail.com>
* net: designware: s700: Add glue code for S700 macAmit Singh Tomar2020-07-071-0/+7
| | | | | | | | | | | | This patchs adds glue logic to enable designware mac present on Action Semi based S700 SoC, Configures SoC specific bits. Undocumented bit that programs the PHY interface select register comes from vendor source. It has been tested on Cubieboard7-lite based on S700 SoC. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
* net: pcnet: Add Kconfig entriesMarek Vasut2020-06-181-0/+6
| | | | | | | | | Add Kconfig entries for the pcnet driver and convert MIPS malta to use those. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
* net: eepro100: Add Kconfig entriesMarek Vasut2020-06-181-0/+6
| | | | | | Add Kconfig entries for the eepro100 driver and convert various boards. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
* drivers: net: e1000: with DM_ETH needs DM_PCI tooMadalin Bucur2020-06-031-0/+1
| | | | | | | Compilation error occur when DM_ETH is enabled without DM_PCI. Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
* net: ks8851: Add Kconfig entriesMarek Vasut2020-05-221-0/+14
| | | | | | | | Convert CONFIG_KS8851_MLL and CONFIG_KS8851_MLL_BASEADDR to Kconfig Signed-off-by: Marek Vasut <marex@denx.de> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
* rename symbol: CONFIG_KIRKWOOD -> CONFIG_ARCH_KIRKWOODTrevor Woerner2020-05-151-1/+1
| | | | | | | | Have this symbol follow the pattern of all other such symbols. This patch also removes a TODO from the code. Reviewed-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Trevor Woerner <twoerner@gmail.com>
* rename symbol: CONFIG_ORION5X -> CONFIG_ARCH_ORION5XTrevor Woerner2020-05-151-1/+1
| | | | | | | Have this symbol follow the pattern of all other such symbols. This patch removes a TODO from the code. Signed-off-by: Trevor Woerner <twoerner@gmail.com>
* net: Add eth phy generic driver for shared MDIOYe Li2020-05-101-0/+6
| | | | | | | | | | | | | | | | | | | For dual ethernet controllers, the HW design may connect ETH phys to one MDIO ports. So two different ethernet drivers have to share MDIO bus. Since two ethernet drivers are independent, we can't ensure their probe order. To resolve this problem, introduce an eth phy generic driver and uclass. After eth-uclass binds, we search the mdio node and binds the phy node with the eth-phy-generic driver. When one eth driver get its phy device, the parent of phy device will probe prior than phy device. So this ensure the eth driver ownes the MDIO bus will be probed before using its MDIO. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
* net: smc911x: Add DM supportMarek Vasut2020-05-011-0/+2
| | | | | | | | | | Add support for U-Boot DM and DT probing. Furthermore, build the SMC911x standalone EEPROM example only for the non-DM case, as it is not converted yet. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
* drivers: net: add Layerscape mEMAC MDIO driverIoana Ciornei2020-04-291-0/+7
| | | | | | | | Add a driver for the MDIO interface integrated in the mEMAC (Multi-rate Ethernet Media Access Controller) and the Fman 10G Ethernet MACs. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
* net: Add support for Broadcom GENETv5 Ethernet controllerAmit Singh Tomar2020-01-291-0/+7
| | | | | | | | | | | | | | | | The Broadcom GENET Ethernet MACs are used in several MIPS based SoCs and in the Broadcom 2711/2838 SoC used on the Raspberry Pi 4. There is no publicly available documentation, so this driver is based on the Linux driver. Compared to that the queue management is drastically simplified, also we only support version 5 of the IP and RGMII connections between MAC and PHY, as used on the RPi4. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> [Andre: heavy cleanup and a few fixes] Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
* drivers: net: add mcf fec dm Kconfig supportAngelo Durgehello2020-01-101-0/+16
| | | | | | Add ColdFire fec to Kconfig. Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
* net: mvpp2: MVPP2 now needs MVMDIONevo Hed2019-12-091-0/+2
| | | | | | | | | Changes to mvpp2.c require the MVMDIO module which in turn uses DM_MDIO. Signed-off-by: Nevo Hed <nhed+github@starry.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* net: Kconfig: FEC: Add dependency on i.MX8MPeng Fan2019-11-051-1/+1
| | | | | | | | | Make FEC driver could be used by i.MX8M when CONFIG_FEC_MXC defined in defconfig. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
* net: mt7628-eth: make phy link up detection optional via DTWeijie Gao2019-10-251-0/+1
| | | | | | | | | | | | The mt7628 has an embedded ethernet switch (5 phy ports + 1 cpu port). Although in IOT mode only port0 is usable, the phy0 is still connected to the switch, not the ethernet gmac directly. This patch rewrites it and makes it optional. It can be turned on by adding mediatek,poll-link-phy = <?> explicitly into the eth node. By default the driver is switch mode with all 5 phy ports working without link detection. Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
* drivers: net: add marvell MDIO driverAlex Marginean2019-09-041-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds a separate driver for the MDIO interface of the Marvell Ethernet controllers based on driver model. There are two reasons to have a separate driver rather than including it inside the MAC driver itself: *) The MDIO interface is shared by all Ethernet ports, so a driver must guarantee non-concurrent accesses to this MDIO interface. The most logical way is to have a separate driver that handles this single MDIO interface, used by all Ethernet ports. *) The MDIO interface is the same between the existing mv643xx_eth driver and the new mvneta/mvpp2 driver. Even though it is for now only used by the mvneta/mvpp2 driver, it will in the future be used by the mv643xx_eth driver as well. This driver supports SMI IEEE for 802.3 Clause 22 and XSMI for IEEE 802.3 Clause 45. This patch also adds device tree binding for marvell MDIO driver. Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* drivers/fsl-mc: Create Kconfig file to manage driver specific configs betterFlorinel Iordache2019-09-041-0/+1
| | | | | | | | Create drivers/net/fsl-mc/Kconfig and move fsl-mc specific configs from arch/arm/cpu/armv8/fsl-layerscape/Kconfig to this new Kconfig Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* drivers: net: driver for MDIO muxes controlled over I2CAlex Marginean2019-09-041-0/+8
| | | | | | | | | | This driver is used for MDIO muxes driven over I2C. This is currently used on Freescale LS1028A QDS board, on which the physical MDIO MUX is controlled by an on-board FPGA which in turn is configured through I2C. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* Revert "drivers: net: driver for MDIO muxes controlled over I2C"Joe Hershberger2019-09-041-8/+0
| | | | This reverts commit d9a9174fa5687521035b2ec82cce86cdcf4f36e6.
* doc: arch: sandbox: Replace all the instances of README.sandboxKeerthy2019-07-291-1/+1
| | | | | | | | | commit 49116e6d236d ("doc: arch: Convert README.sandbox to reST") Moves README.sandbox to doc/arch. Replace all the existing instances to point to the right documentation file. Signed-off-by: Keerthy <j-keerthy@ti.com>
* Merge tag 'u-boot-imx-20190719' of ↵Tom Rini2019-07-271-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | https://gitlab.denx.de/u-boot/custodians/u-boot-imx u-boot-imx-20190719 - CCF for i.MX6 - nandbcb command to write SPL into NAND - Switch to DM (i.MX28) - Boards: Toradex, engicam, DH - Fixes for i.MX8 - Fixes for i.MX7ULP Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/561147504
| * net: fec: Enable support for i.MX28 DM_ETH in the fec_mxc.c driverLukasz Majewski2019-07-191-1/+1
| | | | | | | | | | | | | | | | | | The fec_mxc.c driver can be reused by i.MX28 when DM_ETH is enabled. One only needs to add proper compatible and dependency on FEC_MXC in the Kconfig. Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Marek Vasut <marex@denx.de>
* | drivers: net: driver for MDIO muxes controlled over I2CAlex Marginean2019-07-251-0/+8
| | | | | | | | | | | | | | | | | | | | This driver is used for MDIO muxes driven over I2C. This is currently used on Freescale LS1028A QDS board, on which the physical MDIO MUX is controlled by an on-board FPGA which in turn is configured through I2C. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* | drivers: net: add NXP ENETC MDIO driverAlex Marginean2019-07-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Adds a driver for the MDIO interface currently integrated in LS1028A SoC. This MDIO interface is shared by multiple ethernet interfaces and is presented as a stand-alone PCI function on the SoC ECAM. Ethernet has a functional dependency on MDIO, for simplicity there is a single config option for both. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* | drivers: net: add NXP ENETC ethernet driverAlex Marginean2019-07-251-0/+7
| | | | | | | | | | | | | | | | | | | | | | Adds a driver for NXP ENETC ethernet controller currently integrated in LS1028A. ENETC is a fairly straight-forward BD ring device and interfaces are presented as PCI EPs on the SoC ECAM. Signed-off-by: Catalin Horghidan <catalin.horghidan@nxp.com> Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* | test: dm: add a test for MDIO MUX DM uclassAlex Marginean2019-07-181-0/+10
| | | | | | | | | | | | | | | | | | Adds a test using a makeshift MDIO MUX. The test is based on the existing MDIO test. It uses the last emulated PHY register to verify MUX selection. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* | net: add MDIO_MUX DM classAlex Marginean2019-07-181-0/+12
|/ | | | | | | | | | | | | Adds a class for MDIO MUXes, which control access to a series of downstream child MDIOs. MDIO MUX drivers are required to implement a select function used to switch between child buses. MUX children are registered as MDIO buses and they can be used just like regular MDIOs. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* test: dm: add MDIO testAlex Marginean2019-07-151-0/+10
| | | | | | | | | | A very simple test for DM_MDIO, mimicks a register write/read through the sandbox bus to a dummy PHY. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* net: introduce MDIO DM class for MDIO devicesAlex Marginean2019-07-151-0/+13
| | | | | | | | | | | Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as stand-alone devices. Useful in particular for systems that support DM_ETH and have a stand-alone MDIO hardware block shared by multiple Ethernet interfaces. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* configs: Migrate CONFIG_FMAN_ENET and some related options to KconfigTom Rini2019-05-261-0/+6
| | | | | | | | | Move the main symbol for Freescale Fman Ethernet controller option to Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and rename the SPIFLASH one to follow the same format as all of the others. To do this fully we need to migrate CONFIG_QC, do so. Signed-off-by: Tom Rini <trini@konsulko.com>
* mips: rename mach-mt7620 to mach-mtmipsWeijie Gao2019-05-031-1/+1
| | | | | | | | | | | | | | Currently mach-mt7620 contains only support for mt7628. To avoid confusion, rename mach-mt7620 to mach-mtmips, which means MediaTek MIPS platforms. MT7620 and MT7628 should be distinguished by SOC_MT7620 and SOC_MT7628 because they do not share the same lowlevel codes. Dependencies of four drivers are changed to SOC_MT7628 as these drivers are only used by MT7628. Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
* net: add higmacv300 Ethernet driver for HiSilicon platformShawn Guo2019-04-231-0/+9
| | | | | | | | | | It adds the driver for HIGMACV300 Ethernet controller found on HiSilicon SoCs like Hi3798CV200. It's based on a downstream U-Boot driver, but quite a lot of code gets rewritten and cleaned up to adopt driver model and PHY API. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* net: Kconfig: FEC: Add dependency on VF610Lukasz Majewski2019-04-131-1/+1
| | | | | Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
* arm: socfpga: gen5 enable designware_socfpgaSimon Goldschmidt2019-02-181-0/+1
| | | | | | | | | | | Enable the socfpga specific designware ethernet driver by default for socfpga by implying it when enabling CONFIG_ETH_DESIGNWARE for a MACH_SOCFPGA config. This is required to remove the hacky reset and phy mode handling in arch/arm/mach-socfpga. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
* net: designware: socfpga: adapt to Gen5Simon Goldschmidt2019-02-181-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | This driver was written for Arria10, but it applies to Gen5, too. The main difference is that Gen5 has 2 MACs (Arria10 has 3) and the syscon bits are encoded in the same register, thus an offset is needed. This offset is already read from the devicetree, but for Arria10 it is always 0, which is probably why it has been ignored. By using this offset when writing the phy mode into the syscon regiter, we can use this driver to set the phy mode for both of the MACs on Gen5. Since the PHY mode bits in sysmgr are the same even for Stratix10, let's drop the detection of the sub-mach by checking compatible version and just use the same code for all FPGAs. To work correctly, this driver depends on SYSCON and REGMAP, so select those via Kconfig when it is enabeld. Tested on socfpga_socrates (where the 2nd MAC is connected, so a shift offset is required). Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
* net: mscc: Move ocelot_switch to mscc_eswitch folderHoratiu Vultur2019-02-011-6/+1
| | | | | | | Move file ocelot_switch to mscc_eswitch to prepare to add new net drivers for other MSCC SoCs. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
* net: add MSCC Ocelot switch supportGregory CLEMENT2019-01-231-0/+7
| | | | | | | | This patch adds support for the Microsemi Ethernet switch present on Ocelot SoCs. Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
* ethernet: MediaTek: add ethernet driver for MediaTek ARM-based SoCsWeijie Gao2019-01-141-0/+10
| | | | | | | | | | This patch adds ethernet support for Mediatek ARM-based SoCs, including a minimum setup of the integrated switch. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Mark Lee <Mark-MC.Lee@mediatek.com> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com> Tested-By: "Frank Wunderlich" <frank-w@public-files.de>
* net: add support for bcm6368-enetÁlvaro Fernández Rojas2018-12-191-0/+8
| | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
* net: add support for bcm6348-enetÁlvaro Fernández Rojas2018-12-191-0/+10
| | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
generated by cgit (git 2.34.1) at 2024-11-16 13:22:07 +0000